From: "CK Hu (胡俊光)" <ck.hu@mediatek.com>
To: "angelogioacchino.delregno@collabora.com"
<angelogioacchino.delregno@collabora.com>,
"chunkuang.hu@kernel.org" <chunkuang.hu@kernel.org>
Cc: "linux-kernel@vger.kernel.org" <linux-kernel@vger.kernel.org>,
"linux-mediatek@lists.infradead.org"
<linux-mediatek@lists.infradead.org>,
"wenst@chromium.org" <wenst@chromium.org>,
"kernel@collabora.com" <kernel@collabora.com>,
"dri-devel@lists.freedesktop.org"
<dri-devel@lists.freedesktop.org>,
"linux-arm-kernel@lists.infradead.org"
<linux-arm-kernel@lists.infradead.org>,
"matthias.bgg@gmail.com" <matthias.bgg@gmail.com>,
"nfraprado@collabora.com" <nfraprado@collabora.com>
Subject: Re: [PATCH v6 04/11] drm/mediatek: dp: Use devm variant of drm_bridge_add()
Date: Tue, 18 Jul 2023 09:33:36 +0000 [thread overview]
Message-ID: <0be54099a44dcaeafa3ff930dcd87a780da045fb.camel@mediatek.com> (raw)
In-Reply-To: <20230717141438.274419-5-angelogioacchino.delregno@collabora.com>
Hi, Angelo:
On Mon, 2023-07-17 at 16:14 +0200, AngeloGioacchino Del Regno wrote:
>
> External email : Please do not click links or open attachments until
> you have verified the sender or the content.
> In preparation for adding support for aux-bus, which will add a code
> path that may fail after the drm_bridge_add() call, change that to
> devm_drm_bridge_add() to simplify failure paths later.
Reviewed-by: CK Hu <ck.hu@mediatek.com>
>
> Signed-off-by: AngeloGioacchino Del Regno <
> angelogioacchino.delregno@collabora.com>
> Tested-by: Chen-Yu Tsai <wenst@chromium.org>
> ---
> drivers/gpu/drm/mediatek/mtk_dp.c | 5 +++--
> 1 file changed, 3 insertions(+), 2 deletions(-)
>
> diff --git a/drivers/gpu/drm/mediatek/mtk_dp.c
> b/drivers/gpu/drm/mediatek/mtk_dp.c
> index 98f63d8230e4..fc6cabf5370b 100644
> --- a/drivers/gpu/drm/mediatek/mtk_dp.c
> +++ b/drivers/gpu/drm/mediatek/mtk_dp.c
> @@ -2552,7 +2552,9 @@ static int mtk_dp_probe(struct platform_device
> *pdev)
> DRM_BRIDGE_OP_DETECT | DRM_BRIDGE_OP_EDID |
> DRM_BRIDGE_OP_HPD;
> mtk_dp->bridge.type = mtk_dp->data->bridge_type;
>
> - drm_bridge_add(&mtk_dp->bridge);
> + ret = devm_drm_bridge_add(dev, &mtk_dp->bridge);
> + if (ret)
> + return dev_err_probe(dev, ret, "Failed to add
> bridge\n");
>
> mtk_dp->need_debounce = true;
> timer_setup(&mtk_dp->debounce_timer, mtk_dp_debounce_timer, 0);
> @@ -2570,7 +2572,6 @@ static int mtk_dp_remove(struct platform_device
> *pdev)
> pm_runtime_put(&pdev->dev);
> pm_runtime_disable(&pdev->dev);
> del_timer_sync(&mtk_dp->debounce_timer);
> - drm_bridge_remove(&mtk_dp->bridge);
> platform_device_unregister(mtk_dp->phy_dev);
> if (mtk_dp->audio_pdev)
> platform_device_unregister(mtk_dp->audio_pdev);
> --
> 2.40.1
next prev parent reply other threads:[~2023-07-18 9:33 UTC|newest]
Thread overview: 34+ messages / expand[flat|nested] mbox.gz Atom feed top
2023-07-17 14:14 [PATCH v6 00/11] MediaTek DisplayPort: support eDP and aux-bus AngeloGioacchino Del Regno
2023-07-17 14:14 ` [PATCH v6 01/11] drm/mediatek: dp: Add missing error checks in mtk_dp_parse_capabilities AngeloGioacchino Del Regno
2023-07-18 8:02 ` CK Hu (胡俊光)
2023-07-20 15:56 ` Alexandre Mergnat
2023-07-17 14:14 ` [PATCH v6 02/11] drm/mediatek: dp: Move AUX and panel poweron/off sequence to function AngeloGioacchino Del Regno
2023-07-18 7:49 ` CK Hu (胡俊光)
2023-07-20 15:56 ` Alexandre Mergnat
2023-07-17 14:14 ` [PATCH v6 03/11] drm/mediatek: dp: Change logging to dev for mtk_dp_aux_transfer() AngeloGioacchino Del Regno
2023-07-18 9:19 ` CK Hu (胡俊光)
2023-07-20 15:57 ` Alexandre Mergnat
2023-07-17 14:14 ` [PATCH v6 04/11] drm/mediatek: dp: Use devm variant of drm_bridge_add() AngeloGioacchino Del Regno
2023-07-18 9:33 ` CK Hu (胡俊光) [this message]
2023-07-20 15:58 ` Alexandre Mergnat
2023-07-17 14:14 ` [PATCH v6 05/11] drm/mediatek: dp: Move AUX_P0 setting to mtk_dp_initialize_aux_settings() AngeloGioacchino Del Regno
2023-07-20 2:01 ` CK Hu (胡俊光)
2023-07-20 15:59 ` Alexandre Mergnat
2023-07-17 14:14 ` [PATCH v6 06/11] drm/mediatek: dp: Enable event interrupt only when bridge attached AngeloGioacchino Del Regno
2023-07-20 13:03 ` Alexandre Mergnat
2023-07-17 14:14 ` [PATCH v6 07/11] drm/mediatek: dp: Avoid mutex locks if audio is not supported/enabled AngeloGioacchino Del Regno
2023-07-20 13:05 ` Alexandre Mergnat
2023-07-24 2:33 ` CK Hu (胡俊光)
2023-07-17 14:14 ` [PATCH v6 08/11] drm/mediatek: dp: Move PHY registration to new function AngeloGioacchino Del Regno
2023-07-20 13:58 ` Alexandre Mergnat
2023-07-17 14:14 ` [PATCH v6 09/11] drm/mediatek: dp: Add support for embedded DisplayPort aux-bus AngeloGioacchino Del Regno
2023-07-20 14:30 ` Alexandre Mergnat
2023-07-24 6:24 ` CK Hu (胡俊光)
2023-07-17 14:14 ` [PATCH v6 10/11] drm/mediatek: dp: Add .wait_hpd_asserted() for AUX bus AngeloGioacchino Del Regno
2023-07-20 15:03 ` Alexandre Mergnat
2023-07-24 8:43 ` CK Hu (胡俊光)
2023-07-17 14:14 ` [PATCH v6 11/11] drm/mediatek: dp: Don't register HPD interrupt handler for eDP case AngeloGioacchino Del Regno
2023-07-20 15:55 ` Alexandre Mergnat
2023-07-25 6:37 ` CK Hu (胡俊光)
2023-07-25 7:19 ` AngeloGioacchino Del Regno
2023-07-19 4:00 ` [PATCH v6 00/11] MediaTek DisplayPort: support eDP and aux-bus Chen-Yu Tsai
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=0be54099a44dcaeafa3ff930dcd87a780da045fb.camel@mediatek.com \
--to=ck.hu@mediatek.com \
--cc=angelogioacchino.delregno@collabora.com \
--cc=chunkuang.hu@kernel.org \
--cc=dri-devel@lists.freedesktop.org \
--cc=kernel@collabora.com \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-mediatek@lists.infradead.org \
--cc=matthias.bgg@gmail.com \
--cc=nfraprado@collabora.com \
--cc=wenst@chromium.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox