From: Felipe Alfaro Solana <felipe_alfaro@linuxmail.org>
To: Russell King <rmk@arm.linux.org.uk>
Cc: LKML <linux-kernel@vger.kernel.org>
Subject: Re: 2.5.66-mm2-1 freezes solid after init PCMCIA
Date: 01 Apr 2003 15:02:16 +0200 [thread overview]
Message-ID: <1049202135.612.4.camel@teapot> (raw)
In-Reply-To: <20030401125328.B30470@flint.arm.linux.org.uk>
[-- Attachment #1: Type: text/plain, Size: 1526 bytes --]
On Tue, 2003-04-01 at 13:53, Russell King wrote:
> On Tue, Apr 01, 2003 at 01:20:21PM +0200, Felipe Alfaro Solana wrote:
> > At this point, the machine hangs. This didn't happen with 2.5.66-mm1 or
> > 2.5.66-mm2 (but it happens with 2.5.66-mm2-1). I'm 99% sure this is
> > caused by Dominik or Russell King PCMCIA patches.
>
> What happens if you boot without the cardbus card inserted? If this
> works, please send lspci -vv output. What happens if you insert the
> cardbus card? If this works, again, please send the lspci -vv output.
OK, here we go...
1. Booting 2.5.66-mm2-1 at "init 1" with *no* CardBus card inserted
works fine, as expected. The lspci -vvv for this configuration is
attached to this message as "lspci-no-cardbus-inserted".
2. After booting 2.5.66-mm2-1 with *no* CardBus inserted, inserting my
3CCFE575CT CardBus NIC *does* work nicely (i.e. no freezes and network
working OK). The lspci -vvv for this configuration (booting with no
cardbus adapters at "init 1", inserting the card and bringing up the
network) is attached to this message as "lspci-after-inserting-cardbus".
3. Booting 2.5.66-mm1 with CardBus inserted at "init 1". The lspci -vvv
for this scenario is attached to this message as "lspci-2.5.66-mm1".
Hope this helps. Please, don't hesitate to contact with me for further
information, help or patch-testing :-)
Thanks!.
________________________________________________________________________
Felipe Alfaro Solana
Linux Registered User #287198
http://counter.li.org
[-- Attachment #2: lspci-2.5.66-mm1 --]
[-- Type: text/plain, Size: 7763 bytes --]
00:00.0 Host bridge: Intel Corp. 440BX/ZX/DX - 82443BX/ZX/DX Host bridge (rev 03)
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR-
Latency: 32
Region 0: Memory at e0000000 (32-bit, prefetchable) [size=256M]
Capabilities: [a0] AGP version 1.0
Status: RQ=31 SBA+ 64bit- FW- Rate=x1,x2
Command: RQ=0 SBA- AGP- 64bit- FW- Rate=<none>
00:01.0 PCI bridge: Intel Corp. 440BX/ZX/DX - 82443BX/ZX/DX AGP bridge (rev 03) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32
Bus: primary=00, secondary=01, subordinate=01, sec-latency=32
I/O behind bridge: 0000d000-0000dfff
Memory behind bridge: fca00000-feafffff
Prefetchable memory behind bridge: dc800000-dc8fffff
BridgeCtl: Parity+ SERR- NoISA- VGA+ MAbort- >Reset- FastB2B+
00:07.0 ISA bridge: Intel Corp. 82371AB/EB/MB PIIX4 ISA (rev 02)
Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
00:07.1 IDE interface: Intel Corp. 82371AB/EB/MB PIIX4 IDE (rev 01) (prog-if 80 [Master])
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32
Region 4: I/O ports at ffa0 [size=16]
00:07.2 USB Controller: Intel Corp. 82371AB/EB/MB PIIX4 USB (rev 01) (prog-if 00 [UHCI])
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32
Interrupt: pin D routed to IRQ 9
Region 4: I/O ports at ef80 [size=32]
00:07.3 Bridge: Intel Corp. 82371AB/EB/MB PIIX4 ACPI (rev 03)
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin ? routed to IRQ 9
00:09.0 Multimedia audio controller: Yamaha Corporation YMF-754 [DS-1E Audio Controller]
Subsystem: NEC Corporation: Unknown device 80b5
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR+
Latency: 32 (1250ns min, 6250ns max)
Interrupt: pin A routed to IRQ 5
Region 0: Memory at febf0000 (32-bit, non-prefetchable) [size=32K]
Region 1: I/O ports at ef00 [size=64]
Region 2: I/O ports at efe4 [size=4]
Capabilities: [50] Power Management version 1
Flags: PMEClk- DSI- D1- D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:0c.0 CardBus bridge: Texas Instruments PCI4450 PC card Cardbus Controller
Subsystem: NEC Corporation: Unknown device 80b6
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 168, cache line size 08
Interrupt: pin A routed to IRQ 10
Region 0: Memory at 10000000 (32-bit, non-prefetchable) [size=4K]
Bus: primary=00, secondary=02, subordinate=05, sec-latency=176
Memory window 0: 10400000-107ff000 (prefetchable)
Memory window 1: 10800000-10bff000
I/O window 0: 000002c0-000002c3
I/O window 1: 00001000-000010ff
BridgeCtl: Parity- SERR- ISA- VGA- MAbort- >Reset+ 16bInt+ PostWrite+
16-bit legacy interface ports at 0001
00:0c.1 CardBus bridge: Texas Instruments PCI4450 PC card Cardbus Controller
Subsystem: NEC Corporation: Unknown device 80b6
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 168, cache line size 08
Interrupt: pin B routed to IRQ 5
Region 0: Memory at 10001000 (32-bit, non-prefetchable) [size=4K]
Bus: primary=00, secondary=06, subordinate=09, sec-latency=176
Memory window 0: 10c00000-10fff000 (prefetchable)
Memory window 1: 11000000-113ff000
I/O window 0: 00001400-000014ff
I/O window 1: 00001800-000018ff
BridgeCtl: Parity- SERR- ISA- VGA- MAbort- >Reset- 16bInt- PostWrite+
16-bit legacy interface ports at 0001
00:0c.2 FireWire (IEEE 1394): Texas Instruments: Unknown device 8011 (prog-if 10 [OHCI])
Subsystem: NEC Corporation: Unknown device 80b6
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32 (750ns min, 1000ns max), cache line size 08
Interrupt: pin C routed to IRQ 5
Region 0: Memory at febff000 (32-bit, non-prefetchable) [size=2K]
Region 1: Memory at febf8000 (32-bit, non-prefetchable) [size=16K]
Capabilities: [44] Power Management version 1
Flags: PMEClk- DSI- D1- D2+ AuxCurrent=0mA PME(D0-,D1-,D2+,D3hot+,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:0f.0 Communication controller: Lucent Microelectronics LT WinModem
Subsystem: NEC Corporation: Unknown device 80a8
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32 (63000ns min, 3500ns max)
Interrupt: pin A routed to IRQ 5
Region 0: Memory at febfff00 (32-bit, non-prefetchable) [size=256]
Region 1: I/O ports at eff0 [size=8]
Region 2: I/O ports at e800 [size=256]
Capabilities: [f8] Power Management version 2
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=160mA PME(D0-,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
01:00.0 VGA compatible controller: ATI Technologies Inc Rage Mobility P/M AGP 2x (rev 64) (prog-if 00 [VGA])
Subsystem: NEC Corporation: Unknown device 80b7
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping+ SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32 (2000ns min), cache line size 08
Interrupt: pin A routed to IRQ 10
Region 0: Memory at fd000000 (32-bit, non-prefetchable) [size=16M]
Region 1: I/O ports at d800 [size=256]
Region 2: Memory at feaff000 (32-bit, non-prefetchable) [size=4K]
Expansion ROM at feac0000 [disabled] [size=128K]
Capabilities: [50] AGP version 1.0
Status: RQ=255 SBA+ 64bit- FW- Rate=x1,x2
Command: RQ=0 SBA- AGP- 64bit- FW- Rate=<none>
Capabilities: [5c] Power Management version 1
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
06:00.0 Ethernet controller: 3Com Corporation 3CCFE575CT Cyclone CardBus (rev 10)
Subsystem: 3Com Corporation FE575C-3Com 10/100 LAN CardBus-Fast Ethernet
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin A routed to IRQ 5
Region 0: I/O ports at 1400 [size=256]
Region 1: Memory at 11000000 (32-bit, non-prefetchable) [size=128]
Region 2: Memory at 11000080 (32-bit, non-prefetchable) [size=128]
Expansion ROM at 10c00000 [disabled] [size=128K]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=1 PME-
[-- Attachment #3: lspci-after-inserting-cardbus --]
[-- Type: text/plain, Size: 7801 bytes --]
00:00.0 Host bridge: Intel Corp. 440BX/ZX/DX - 82443BX/ZX/DX Host bridge (rev 03)
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR-
Latency: 32
Region 0: Memory at e0000000 (32-bit, prefetchable) [size=256M]
Capabilities: [a0] AGP version 1.0
Status: RQ=31 SBA+ 64bit- FW- Rate=x1,x2
Command: RQ=0 SBA- AGP- 64bit- FW- Rate=<none>
00:01.0 PCI bridge: Intel Corp. 440BX/ZX/DX - 82443BX/ZX/DX AGP bridge (rev 03) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32
Bus: primary=00, secondary=01, subordinate=01, sec-latency=32
I/O behind bridge: 0000d000-0000dfff
Memory behind bridge: fca00000-feafffff
Prefetchable memory behind bridge: dc800000-dc8fffff
BridgeCtl: Parity+ SERR- NoISA- VGA+ MAbort- >Reset- FastB2B+
00:07.0 ISA bridge: Intel Corp. 82371AB/EB/MB PIIX4 ISA (rev 02)
Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
00:07.1 IDE interface: Intel Corp. 82371AB/EB/MB PIIX4 IDE (rev 01) (prog-if 80 [Master])
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32
Region 4: I/O ports at ffa0 [size=16]
00:07.2 USB Controller: Intel Corp. 82371AB/EB/MB PIIX4 USB (rev 01) (prog-if 00 [UHCI])
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32
Interrupt: pin D routed to IRQ 9
Region 4: I/O ports at ef80 [size=32]
00:07.3 Bridge: Intel Corp. 82371AB/EB/MB PIIX4 ACPI (rev 03)
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin ? routed to IRQ 9
00:09.0 Multimedia audio controller: Yamaha Corporation YMF-754 [DS-1E Audio Controller]
Subsystem: NEC Corporation: Unknown device 80b5
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR+
Latency: 32 (1250ns min, 6250ns max)
Interrupt: pin A routed to IRQ 5
Region 0: Memory at febf0000 (32-bit, non-prefetchable) [size=32K]
Region 1: I/O ports at ef00 [size=64]
Region 2: I/O ports at efe4 [size=4]
Capabilities: [50] Power Management version 1
Flags: PMEClk- DSI- D1- D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:0c.0 CardBus bridge: Texas Instruments PCI4450 PC card Cardbus Controller
Subsystem: NEC Corporation: Unknown device 80b6
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 168, cache line size 08
Interrupt: pin A routed to IRQ 10
Region 0: Memory at 10000000 (32-bit, non-prefetchable) [size=4K]
Bus: primary=00, secondary=02, subordinate=05, sec-latency=176
Memory window 0: 10400000-107ff000 (prefetchable)
Memory window 1: 10800000-10bff000
I/O window 0: 000002c0-000002c3
I/O window 1: 00001000-000010ff
BridgeCtl: Parity- SERR- ISA- VGA- MAbort- >Reset+ 16bInt+ PostWrite+
16-bit legacy interface ports at 0001
00:0c.1 CardBus bridge: Texas Instruments PCI4450 PC card Cardbus Controller
Subsystem: NEC Corporation: Unknown device 80b6
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 168, cache line size 08
Interrupt: pin B routed to IRQ 5
Region 0: Memory at 10001000 (32-bit, non-prefetchable) [size=4K]
Bus: primary=00, secondary=06, subordinate=09, sec-latency=176
Memory window 0: 10c00000-10fff000 (prefetchable)
Memory window 1: 11000000-113ff000
I/O window 0: 00001400-000014ff
I/O window 1: 00001800-000018ff
BridgeCtl: Parity- SERR- ISA- VGA- MAbort- >Reset- 16bInt- PostWrite+
16-bit legacy interface ports at 0001
00:0c.2 FireWire (IEEE 1394): Texas Instruments: Unknown device 8011 (prog-if 10 [OHCI])
Subsystem: NEC Corporation: Unknown device 80b6
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32 (750ns min, 1000ns max), cache line size 08
Interrupt: pin C routed to IRQ 5
Region 0: Memory at febff000 (32-bit, non-prefetchable) [size=2K]
Region 1: Memory at febf8000 (32-bit, non-prefetchable) [size=16K]
Capabilities: [44] Power Management version 1
Flags: PMEClk- DSI- D1- D2+ AuxCurrent=0mA PME(D0-,D1-,D2+,D3hot+,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:0f.0 Communication controller: Lucent Microelectronics LT WinModem
Subsystem: NEC Corporation: Unknown device 80a8
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32 (63000ns min, 3500ns max)
Interrupt: pin A routed to IRQ 5
Region 0: Memory at febfff00 (32-bit, non-prefetchable) [size=256]
Region 1: I/O ports at eff0 [size=8]
Region 2: I/O ports at e800 [size=256]
Capabilities: [f8] Power Management version 2
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=160mA PME(D0-,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
01:00.0 VGA compatible controller: ATI Technologies Inc Rage Mobility P/M AGP 2x (rev 64) (prog-if 00 [VGA])
Subsystem: NEC Corporation: Unknown device 80b7
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping+ SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32 (2000ns min), cache line size 08
Interrupt: pin A routed to IRQ 10
Region 0: Memory at fd000000 (32-bit, non-prefetchable) [size=16M]
Region 1: I/O ports at d800 [size=256]
Region 2: Memory at feaff000 (32-bit, non-prefetchable) [size=4K]
Expansion ROM at feac0000 [disabled] [size=128K]
Capabilities: [50] AGP version 1.0
Status: RQ=255 SBA+ 64bit- FW- Rate=x1,x2
Command: RQ=0 SBA- AGP- 64bit- FW- Rate=<none>
Capabilities: [5c] Power Management version 1
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
06:00.0 Ethernet controller: 3Com Corporation 3CCFE575CT Cyclone CardBus (rev 10)
Subsystem: 3Com Corporation FE575C-3Com 10/100 LAN CardBus-Fast Ethernet
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (2500ns min, 1250ns max)
Interrupt: pin A routed to IRQ 5
Region 0: I/O ports at 1400 [size=256]
Region 1: Memory at 11000000 (32-bit, non-prefetchable) [size=128]
Region 2: Memory at 11000080 (32-bit, non-prefetchable) [size=128]
Expansion ROM at 10c00000 [disabled] [size=128K]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=1 PME-
[-- Attachment #4: lspci-no-cardbus-inserted --]
[-- Type: text/plain, Size: 6984 bytes --]
00:00.0 Host bridge: Intel Corp. 440BX/ZX/DX - 82443BX/ZX/DX Host bridge (rev 03)
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR-
Latency: 32
Region 0: Memory at e0000000 (32-bit, prefetchable) [size=256M]
Capabilities: [a0] AGP version 1.0
Status: RQ=31 SBA+ 64bit- FW- Rate=x1,x2
Command: RQ=0 SBA- AGP- 64bit- FW- Rate=<none>
00:01.0 PCI bridge: Intel Corp. 440BX/ZX/DX - 82443BX/ZX/DX AGP bridge (rev 03) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32
Bus: primary=00, secondary=01, subordinate=01, sec-latency=32
I/O behind bridge: 0000d000-0000dfff
Memory behind bridge: fca00000-feafffff
Prefetchable memory behind bridge: dc800000-dc8fffff
BridgeCtl: Parity+ SERR- NoISA- VGA+ MAbort- >Reset- FastB2B+
00:07.0 ISA bridge: Intel Corp. 82371AB/EB/MB PIIX4 ISA (rev 02)
Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
00:07.1 IDE interface: Intel Corp. 82371AB/EB/MB PIIX4 IDE (rev 01) (prog-if 80 [Master])
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32
Region 4: I/O ports at ffa0 [size=16]
00:07.2 USB Controller: Intel Corp. 82371AB/EB/MB PIIX4 USB (rev 01) (prog-if 00 [UHCI])
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32
Interrupt: pin D routed to IRQ 9
Region 4: I/O ports at ef80 [size=32]
00:07.3 Bridge: Intel Corp. 82371AB/EB/MB PIIX4 ACPI (rev 03)
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin ? routed to IRQ 9
00:09.0 Multimedia audio controller: Yamaha Corporation YMF-754 [DS-1E Audio Controller]
Subsystem: NEC Corporation: Unknown device 80b5
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR+
Latency: 32 (1250ns min, 6250ns max)
Interrupt: pin A routed to IRQ 5
Region 0: Memory at febf0000 (32-bit, non-prefetchable) [size=32K]
Region 1: I/O ports at ef00 [size=64]
Region 2: I/O ports at efe4 [size=4]
Capabilities: [50] Power Management version 1
Flags: PMEClk- DSI- D1- D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:0c.0 CardBus bridge: Texas Instruments PCI4450 PC card Cardbus Controller
Subsystem: NEC Corporation: Unknown device 80b6
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 168, cache line size 08
Interrupt: pin A routed to IRQ 10
Region 0: Memory at 10000000 (32-bit, non-prefetchable) [size=4K]
Bus: primary=00, secondary=02, subordinate=05, sec-latency=176
Memory window 0: 10400000-107ff000 (prefetchable)
Memory window 1: 10800000-10bff000
I/O window 0: 000002c0-000002c3
I/O window 1: 00001000-000010ff
BridgeCtl: Parity- SERR- ISA- VGA- MAbort- >Reset+ 16bInt+ PostWrite+
16-bit legacy interface ports at 0001
00:0c.1 CardBus bridge: Texas Instruments PCI4450 PC card Cardbus Controller
Subsystem: NEC Corporation: Unknown device 80b6
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 168, cache line size 08
Interrupt: pin B routed to IRQ 5
Region 0: Memory at 10001000 (32-bit, non-prefetchable) [size=4K]
Bus: primary=00, secondary=06, subordinate=09, sec-latency=176
Memory window 0: 10c00000-10fff000 (prefetchable)
Memory window 1: 11000000-113ff000
I/O window 0: 00001400-000014ff
I/O window 1: 00001800-000018ff
BridgeCtl: Parity- SERR- ISA- VGA- MAbort- >Reset+ 16bInt+ PostWrite+
16-bit legacy interface ports at 0001
00:0c.2 FireWire (IEEE 1394): Texas Instruments: Unknown device 8011 (prog-if 10 [OHCI])
Subsystem: NEC Corporation: Unknown device 80b6
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32 (750ns min, 1000ns max), cache line size 08
Interrupt: pin C routed to IRQ 5
Region 0: Memory at febff000 (32-bit, non-prefetchable) [size=2K]
Region 1: Memory at febf8000 (32-bit, non-prefetchable) [size=16K]
Capabilities: [44] Power Management version 1
Flags: PMEClk- DSI- D1- D2+ AuxCurrent=0mA PME(D0-,D1-,D2+,D3hot+,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:0f.0 Communication controller: Lucent Microelectronics LT WinModem
Subsystem: NEC Corporation: Unknown device 80a8
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32 (63000ns min, 3500ns max)
Interrupt: pin A routed to IRQ 5
Region 0: Memory at febfff00 (32-bit, non-prefetchable) [size=256]
Region 1: I/O ports at eff0 [size=8]
Region 2: I/O ports at e800 [size=256]
Capabilities: [f8] Power Management version 2
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=160mA PME(D0-,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
01:00.0 VGA compatible controller: ATI Technologies Inc Rage Mobility P/M AGP 2x (rev 64) (prog-if 00 [VGA])
Subsystem: NEC Corporation: Unknown device 80b7
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping+ SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32 (2000ns min), cache line size 08
Interrupt: pin A routed to IRQ 10
Region 0: Memory at fd000000 (32-bit, non-prefetchable) [size=16M]
Region 1: I/O ports at d800 [size=256]
Region 2: Memory at feaff000 (32-bit, non-prefetchable) [size=4K]
Expansion ROM at feac0000 [disabled] [size=128K]
Capabilities: [50] AGP version 1.0
Status: RQ=255 SBA+ 64bit- FW- Rate=x1,x2
Command: RQ=0 SBA- AGP- 64bit- FW- Rate=<none>
Capabilities: [5c] Power Management version 1
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
next prev parent reply other threads:[~2003-04-01 12:51 UTC|newest]
Thread overview: 5+ messages / expand[flat|nested] mbox.gz Atom feed top
2003-04-01 11:20 2.5.66-mm2-1 freezes solid after init PCMCIA Felipe Alfaro Solana
2003-04-01 11:53 ` Russell King
2003-04-01 13:02 ` Felipe Alfaro Solana [this message]
2003-04-01 19:46 ` Russell King
2003-04-01 21:01 ` Felipe Alfaro Solana
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1049202135.612.4.camel@teapot \
--to=felipe_alfaro@linuxmail.org \
--cc=linux-kernel@vger.kernel.org \
--cc=rmk@arm.linux.org.uk \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox