2.5.66-mm2-1 freezes solid after init PCMCIA

public inbox for linux-kernel@vger.kernel.org
 help / color / mirror / Atom feed

* 2.5.66-mm2-1 freezes solid after init PCMCIA
@ 2003-04-01 11:20 Felipe Alfaro Solana
  2003-04-01 11:53 ` Russell King
  0 siblings, 1 reply; 5+ messages in thread
From: Felipe Alfaro Solana @ 2003-04-01 11:20 UTC (permalink / raw)
  To: LKML

Hi,

2.5.66-mm2-1 freezes solid after initialising PCMCIA yenta. Next written
by hand:

PCI: Found IRQ 10 for device 00:0c.0
yenta 00:0c.0: Preassigned resource 3 busy, reconfiguring...
Yenta IRQ list 08d8, PCI irq10
Socket status: 30000006
PCI: Found IRQ 5 for device 00:0c.1
PCI: Sharing IRQ 5 with 00:09.0
yenta 00:0c.1: Preassigned resource 2 busy, reconfiguring...
yenta 00:0c.1: Preassigned resource 3 busy, reconfiguring...
Yenta IRQ list 08d8, PCI irq5
Socket status: 30000020

At this point, the machine hangs. This didn't happen with 2.5.66-mm1 or
2.5.66-mm2 (but it happens with 2.5.66-mm2-1). I'm 99% sure this is
caused by Dominik or Russell King PCMCIA patches.

________________________________________________________________________
        Felipe Alfaro Solana
   Linux Registered User #287198
http://counter.li.org

^ permalink raw reply	[flat|nested] 5+ messages in thread

* Re: 2.5.66-mm2-1 freezes solid after init PCMCIA
  2003-04-01 11:20 2.5.66-mm2-1 freezes solid after init PCMCIA Felipe Alfaro Solana
@ 2003-04-01 11:53 ` Russell King
  2003-04-01 13:02   ` Felipe Alfaro Solana
  0 siblings, 1 reply; 5+ messages in thread
From: Russell King @ 2003-04-01 11:53 UTC (permalink / raw)
  To: Felipe Alfaro Solana; +Cc: LKML

On Tue, Apr 01, 2003 at 01:20:21PM +0200, Felipe Alfaro Solana wrote:
> PCI: Found IRQ 10 for device 00:0c.0
> yenta 00:0c.0: Preassigned resource 3 busy, reconfiguring...
> Yenta IRQ list 08d8, PCI irq10
> Socket status: 30000006
> PCI: Found IRQ 5 for device 00:0c.1
> PCI: Sharing IRQ 5 with 00:09.0
> yenta 00:0c.1: Preassigned resource 2 busy, reconfiguring...
> yenta 00:0c.1: Preassigned resource 3 busy, reconfiguring...
> Yenta IRQ list 08d8, PCI irq5
> Socket status: 30000020
> 
> At this point, the machine hangs. This didn't happen with 2.5.66-mm1 or
> 2.5.66-mm2 (but it happens with 2.5.66-mm2-1). I'm 99% sure this is
> caused by Dominik or Russell King PCMCIA patches.

What happens if you boot without the cardbus card inserted?  If this
works, please send lspci -vv output.  What happens if you insert the
cardbus card?  If this works, again, please send the lspci -vv output.

Please send lspci -vv output under a kernel which works with the card
inserted.

(so you should have up to 3 lspci outputs to send me.)

Thanks.

-- 
Russell King (rmk@arm.linux.org.uk)                The developer of ARM Linux
             http://www.arm.linux.org.uk/personal/aboutme.html


^ permalink raw reply	[flat|nested] 5+ messages in thread

* Re: 2.5.66-mm2-1 freezes solid after init PCMCIA
  2003-04-01 11:53 ` Russell King
@ 2003-04-01 13:02   ` Felipe Alfaro Solana
  2003-04-01 19:46     ` Russell King
  0 siblings, 1 reply; 5+ messages in thread
From: Felipe Alfaro Solana @ 2003-04-01 13:02 UTC (permalink / raw)
  To: Russell King; +Cc: LKML

[-- Attachment #1: Type: text/plain, Size: 1526 bytes --]

On Tue, 2003-04-01 at 13:53, Russell King wrote:
> On Tue, Apr 01, 2003 at 01:20:21PM +0200, Felipe Alfaro Solana wrote:
> > At this point, the machine hangs. This didn't happen with 2.5.66-mm1 or
> > 2.5.66-mm2 (but it happens with 2.5.66-mm2-1). I'm 99% sure this is
> > caused by Dominik or Russell King PCMCIA patches.
> 
> What happens if you boot without the cardbus card inserted?  If this
> works, please send lspci -vv output.  What happens if you insert the
> cardbus card?  If this works, again, please send the lspci -vv output.

OK, here we go...

1. Booting 2.5.66-mm2-1 at "init 1" with *no* CardBus card inserted
works fine, as expected. The lspci -vvv for this configuration is
attached to this message as "lspci-no-cardbus-inserted".

2. After booting 2.5.66-mm2-1 with *no* CardBus inserted, inserting my
3CCFE575CT CardBus NIC *does* work nicely (i.e. no freezes and network
working OK). The lspci -vvv for this configuration (booting with no
cardbus adapters at "init 1", inserting the card and bringing up the
network) is attached to this message as "lspci-after-inserting-cardbus".

3. Booting 2.5.66-mm1 with CardBus inserted at "init 1". The lspci -vvv
for this scenario is attached to this message as "lspci-2.5.66-mm1".

Hope this helps. Please, don't hesitate to contact with me for further
information, help or patch-testing :-)

Thanks!.

________________________________________________________________________
        Felipe Alfaro Solana
   Linux Registered User #287198
http://counter.li.org

[-- Attachment #2: lspci-2.5.66-mm1 --]
[-- Type: text/plain, Size: 7763 bytes --]

00:00.0 Host bridge: Intel Corp. 440BX/ZX/DX - 82443BX/ZX/DX Host bridge (rev 03)
	Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
	Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR-
	Latency: 32
	Region 0: Memory at e0000000 (32-bit, prefetchable) [size=256M]
	Capabilities: [a0] AGP version 1.0
		Status: RQ=31 SBA+ 64bit- FW- Rate=x1,x2
		Command: RQ=0 SBA- AGP- 64bit- FW- Rate=<none>

00:01.0 PCI bridge: Intel Corp. 440BX/ZX/DX - 82443BX/ZX/DX AGP bridge (rev 03) (prog-if 00 [Normal decode])
	Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B-
	Status: Cap- 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
	Latency: 32
	Bus: primary=00, secondary=01, subordinate=01, sec-latency=32
	I/O behind bridge: 0000d000-0000dfff
	Memory behind bridge: fca00000-feafffff
	Prefetchable memory behind bridge: dc800000-dc8fffff
	BridgeCtl: Parity+ SERR- NoISA- VGA+ MAbort- >Reset- FastB2B+

00:07.0 ISA bridge: Intel Corp. 82371AB/EB/MB PIIX4 ISA (rev 02)
	Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
	Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
	Latency: 0

00:07.1 IDE interface: Intel Corp. 82371AB/EB/MB PIIX4 IDE (rev 01) (prog-if 80 [Master])
	Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
	Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
	Latency: 32
	Region 4: I/O ports at ffa0 [size=16]

00:07.2 USB Controller: Intel Corp. 82371AB/EB/MB PIIX4 USB (rev 01) (prog-if 00 [UHCI])
	Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
	Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
	Latency: 32
	Interrupt: pin D routed to IRQ 9
	Region 4: I/O ports at ef80 [size=32]

00:07.3 Bridge: Intel Corp. 82371AB/EB/MB PIIX4 ACPI (rev 03)
	Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
	Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
	Interrupt: pin ? routed to IRQ 9

00:09.0 Multimedia audio controller: Yamaha Corporation YMF-754 [DS-1E Audio Controller]
	Subsystem: NEC Corporation: Unknown device 80b5
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
	Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR+
	Latency: 32 (1250ns min, 6250ns max)
	Interrupt: pin A routed to IRQ 5
	Region 0: Memory at febf0000 (32-bit, non-prefetchable) [size=32K]
	Region 1: I/O ports at ef00 [size=64]
	Region 2: I/O ports at efe4 [size=4]
	Capabilities: [50] Power Management version 1
		Flags: PMEClk- DSI- D1- D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
		Status: D0 PME-Enable- DSel=0 DScale=0 PME-

00:0c.0 CardBus bridge: Texas Instruments PCI4450 PC card Cardbus Controller
	Subsystem: NEC Corporation: Unknown device 80b6
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
	Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
	Latency: 168, cache line size 08
	Interrupt: pin A routed to IRQ 10
	Region 0: Memory at 10000000 (32-bit, non-prefetchable) [size=4K]
	Bus: primary=00, secondary=02, subordinate=05, sec-latency=176
	Memory window 0: 10400000-107ff000 (prefetchable)
	Memory window 1: 10800000-10bff000
	I/O window 0: 000002c0-000002c3
	I/O window 1: 00001000-000010ff
	BridgeCtl: Parity- SERR- ISA- VGA- MAbort- >Reset+ 16bInt+ PostWrite+
	16-bit legacy interface ports at 0001

00:0c.1 CardBus bridge: Texas Instruments PCI4450 PC card Cardbus Controller
	Subsystem: NEC Corporation: Unknown device 80b6
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
	Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
	Latency: 168, cache line size 08
	Interrupt: pin B routed to IRQ 5
	Region 0: Memory at 10001000 (32-bit, non-prefetchable) [size=4K]
	Bus: primary=00, secondary=06, subordinate=09, sec-latency=176
	Memory window 0: 10c00000-10fff000 (prefetchable)
	Memory window 1: 11000000-113ff000
	I/O window 0: 00001400-000014ff
	I/O window 1: 00001800-000018ff
	BridgeCtl: Parity- SERR- ISA- VGA- MAbort- >Reset- 16bInt- PostWrite+
	16-bit legacy interface ports at 0001

00:0c.2 FireWire (IEEE 1394): Texas Instruments: Unknown device 8011 (prog-if 10 [OHCI])
	Subsystem: NEC Corporation: Unknown device 80b6
	Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR+ FastB2B-
	Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
	Latency: 32 (750ns min, 1000ns max), cache line size 08
	Interrupt: pin C routed to IRQ 5
	Region 0: Memory at febff000 (32-bit, non-prefetchable) [size=2K]
	Region 1: Memory at febf8000 (32-bit, non-prefetchable) [size=16K]
	Capabilities: [44] Power Management version 1
		Flags: PMEClk- DSI- D1- D2+ AuxCurrent=0mA PME(D0-,D1-,D2+,D3hot+,D3cold-)
		Status: D0 PME-Enable- DSel=0 DScale=0 PME-

00:0f.0 Communication controller: Lucent Microelectronics LT WinModem
	Subsystem: NEC Corporation: Unknown device 80a8
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
	Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
	Latency: 32 (63000ns min, 3500ns max)
	Interrupt: pin A routed to IRQ 5
	Region 0: Memory at febfff00 (32-bit, non-prefetchable) [size=256]
	Region 1: I/O ports at eff0 [size=8]
	Region 2: I/O ports at e800 [size=256]
	Capabilities: [f8] Power Management version 2
		Flags: PMEClk- DSI+ D1- D2- AuxCurrent=160mA PME(D0-,D1-,D2-,D3hot+,D3cold+)
		Status: D0 PME-Enable- DSel=0 DScale=0 PME-

01:00.0 VGA compatible controller: ATI Technologies Inc Rage Mobility P/M AGP 2x (rev 64) (prog-if 00 [VGA])
	Subsystem: NEC Corporation: Unknown device 80b7
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping+ SERR- FastB2B-
	Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
	Latency: 32 (2000ns min), cache line size 08
	Interrupt: pin A routed to IRQ 10
	Region 0: Memory at fd000000 (32-bit, non-prefetchable) [size=16M]
	Region 1: I/O ports at d800 [size=256]
	Region 2: Memory at feaff000 (32-bit, non-prefetchable) [size=4K]
	Expansion ROM at feac0000 [disabled] [size=128K]
	Capabilities: [50] AGP version 1.0
		Status: RQ=255 SBA+ 64bit- FW- Rate=x1,x2
		Command: RQ=0 SBA- AGP- 64bit- FW- Rate=<none>
	Capabilities: [5c] Power Management version 1
		Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
		Status: D0 PME-Enable- DSel=0 DScale=0 PME-

06:00.0 Ethernet controller: 3Com Corporation 3CCFE575CT Cyclone CardBus (rev 10)
	Subsystem: 3Com Corporation FE575C-3Com 10/100 LAN CardBus-Fast Ethernet
	Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
	Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
	Interrupt: pin A routed to IRQ 5
	Region 0: I/O ports at 1400 [size=256]
	Region 1: Memory at 11000000 (32-bit, non-prefetchable) [size=128]
	Region 2: Memory at 11000080 (32-bit, non-prefetchable) [size=128]
	Expansion ROM at 10c00000 [disabled] [size=128K]
	Capabilities: [50] Power Management version 2
		Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1+,D2+,D3hot+,D3cold+)
		Status: D0 PME-Enable- DSel=0 DScale=1 PME-


[-- Attachment #3: lspci-after-inserting-cardbus --]
[-- Type: text/plain, Size: 7801 bytes --]

00:00.0 Host bridge: Intel Corp. 440BX/ZX/DX - 82443BX/ZX/DX Host bridge (rev 03)
	Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
	Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR-
	Latency: 32
	Region 0: Memory at e0000000 (32-bit, prefetchable) [size=256M]
	Capabilities: [a0] AGP version 1.0
		Status: RQ=31 SBA+ 64bit- FW- Rate=x1,x2
		Command: RQ=0 SBA- AGP- 64bit- FW- Rate=<none>

00:01.0 PCI bridge: Intel Corp. 440BX/ZX/DX - 82443BX/ZX/DX AGP bridge (rev 03) (prog-if 00 [Normal decode])
	Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B-
	Status: Cap- 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
	Latency: 32
	Bus: primary=00, secondary=01, subordinate=01, sec-latency=32
	I/O behind bridge: 0000d000-0000dfff
	Memory behind bridge: fca00000-feafffff
	Prefetchable memory behind bridge: dc800000-dc8fffff
	BridgeCtl: Parity+ SERR- NoISA- VGA+ MAbort- >Reset- FastB2B+

00:07.0 ISA bridge: Intel Corp. 82371AB/EB/MB PIIX4 ISA (rev 02)
	Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
	Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
	Latency: 0

00:07.1 IDE interface: Intel Corp. 82371AB/EB/MB PIIX4 IDE (rev 01) (prog-if 80 [Master])
	Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
	Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
	Latency: 32
	Region 4: I/O ports at ffa0 [size=16]

00:07.2 USB Controller: Intel Corp. 82371AB/EB/MB PIIX4 USB (rev 01) (prog-if 00 [UHCI])
	Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
	Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
	Latency: 32
	Interrupt: pin D routed to IRQ 9
	Region 4: I/O ports at ef80 [size=32]

00:07.3 Bridge: Intel Corp. 82371AB/EB/MB PIIX4 ACPI (rev 03)
	Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
	Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
	Interrupt: pin ? routed to IRQ 9

00:09.0 Multimedia audio controller: Yamaha Corporation YMF-754 [DS-1E Audio Controller]
	Subsystem: NEC Corporation: Unknown device 80b5
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
	Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR+
	Latency: 32 (1250ns min, 6250ns max)
	Interrupt: pin A routed to IRQ 5
	Region 0: Memory at febf0000 (32-bit, non-prefetchable) [size=32K]
	Region 1: I/O ports at ef00 [size=64]
	Region 2: I/O ports at efe4 [size=4]
	Capabilities: [50] Power Management version 1
		Flags: PMEClk- DSI- D1- D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
		Status: D0 PME-Enable- DSel=0 DScale=0 PME-

00:0c.0 CardBus bridge: Texas Instruments PCI4450 PC card Cardbus Controller
	Subsystem: NEC Corporation: Unknown device 80b6
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
	Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
	Latency: 168, cache line size 08
	Interrupt: pin A routed to IRQ 10
	Region 0: Memory at 10000000 (32-bit, non-prefetchable) [size=4K]
	Bus: primary=00, secondary=02, subordinate=05, sec-latency=176
	Memory window 0: 10400000-107ff000 (prefetchable)
	Memory window 1: 10800000-10bff000
	I/O window 0: 000002c0-000002c3
	I/O window 1: 00001000-000010ff
	BridgeCtl: Parity- SERR- ISA- VGA- MAbort- >Reset+ 16bInt+ PostWrite+
	16-bit legacy interface ports at 0001

00:0c.1 CardBus bridge: Texas Instruments PCI4450 PC card Cardbus Controller
	Subsystem: NEC Corporation: Unknown device 80b6
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
	Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
	Latency: 168, cache line size 08
	Interrupt: pin B routed to IRQ 5
	Region 0: Memory at 10001000 (32-bit, non-prefetchable) [size=4K]
	Bus: primary=00, secondary=06, subordinate=09, sec-latency=176
	Memory window 0: 10c00000-10fff000 (prefetchable)
	Memory window 1: 11000000-113ff000
	I/O window 0: 00001400-000014ff
	I/O window 1: 00001800-000018ff
	BridgeCtl: Parity- SERR- ISA- VGA- MAbort- >Reset- 16bInt- PostWrite+
	16-bit legacy interface ports at 0001

00:0c.2 FireWire (IEEE 1394): Texas Instruments: Unknown device 8011 (prog-if 10 [OHCI])
	Subsystem: NEC Corporation: Unknown device 80b6
	Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR+ FastB2B-
	Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
	Latency: 32 (750ns min, 1000ns max), cache line size 08
	Interrupt: pin C routed to IRQ 5
	Region 0: Memory at febff000 (32-bit, non-prefetchable) [size=2K]
	Region 1: Memory at febf8000 (32-bit, non-prefetchable) [size=16K]
	Capabilities: [44] Power Management version 1
		Flags: PMEClk- DSI- D1- D2+ AuxCurrent=0mA PME(D0-,D1-,D2+,D3hot+,D3cold-)
		Status: D0 PME-Enable- DSel=0 DScale=0 PME-

00:0f.0 Communication controller: Lucent Microelectronics LT WinModem
	Subsystem: NEC Corporation: Unknown device 80a8
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
	Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
	Latency: 32 (63000ns min, 3500ns max)
	Interrupt: pin A routed to IRQ 5
	Region 0: Memory at febfff00 (32-bit, non-prefetchable) [size=256]
	Region 1: I/O ports at eff0 [size=8]
	Region 2: I/O ports at e800 [size=256]
	Capabilities: [f8] Power Management version 2
		Flags: PMEClk- DSI+ D1- D2- AuxCurrent=160mA PME(D0-,D1-,D2-,D3hot+,D3cold+)
		Status: D0 PME-Enable- DSel=0 DScale=0 PME-

01:00.0 VGA compatible controller: ATI Technologies Inc Rage Mobility P/M AGP 2x (rev 64) (prog-if 00 [VGA])
	Subsystem: NEC Corporation: Unknown device 80b7
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping+ SERR- FastB2B-
	Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
	Latency: 32 (2000ns min), cache line size 08
	Interrupt: pin A routed to IRQ 10
	Region 0: Memory at fd000000 (32-bit, non-prefetchable) [size=16M]
	Region 1: I/O ports at d800 [size=256]
	Region 2: Memory at feaff000 (32-bit, non-prefetchable) [size=4K]
	Expansion ROM at feac0000 [disabled] [size=128K]
	Capabilities: [50] AGP version 1.0
		Status: RQ=255 SBA+ 64bit- FW- Rate=x1,x2
		Command: RQ=0 SBA- AGP- 64bit- FW- Rate=<none>
	Capabilities: [5c] Power Management version 1
		Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
		Status: D0 PME-Enable- DSel=0 DScale=0 PME-

06:00.0 Ethernet controller: 3Com Corporation 3CCFE575CT Cyclone CardBus (rev 10)
	Subsystem: 3Com Corporation FE575C-3Com 10/100 LAN CardBus-Fast Ethernet
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
	Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
	Latency: 64 (2500ns min, 1250ns max)
	Interrupt: pin A routed to IRQ 5
	Region 0: I/O ports at 1400 [size=256]
	Region 1: Memory at 11000000 (32-bit, non-prefetchable) [size=128]
	Region 2: Memory at 11000080 (32-bit, non-prefetchable) [size=128]
	Expansion ROM at 10c00000 [disabled] [size=128K]
	Capabilities: [50] Power Management version 2
		Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1+,D2+,D3hot+,D3cold+)
		Status: D0 PME-Enable- DSel=0 DScale=1 PME-


[-- Attachment #4: lspci-no-cardbus-inserted --]
[-- Type: text/plain, Size: 6984 bytes --]

00:00.0 Host bridge: Intel Corp. 440BX/ZX/DX - 82443BX/ZX/DX Host bridge (rev 03)
	Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
	Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR-
	Latency: 32
	Region 0: Memory at e0000000 (32-bit, prefetchable) [size=256M]
	Capabilities: [a0] AGP version 1.0
		Status: RQ=31 SBA+ 64bit- FW- Rate=x1,x2
		Command: RQ=0 SBA- AGP- 64bit- FW- Rate=<none>

00:01.0 PCI bridge: Intel Corp. 440BX/ZX/DX - 82443BX/ZX/DX AGP bridge (rev 03) (prog-if 00 [Normal decode])
	Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B-
	Status: Cap- 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
	Latency: 32
	Bus: primary=00, secondary=01, subordinate=01, sec-latency=32
	I/O behind bridge: 0000d000-0000dfff
	Memory behind bridge: fca00000-feafffff
	Prefetchable memory behind bridge: dc800000-dc8fffff
	BridgeCtl: Parity+ SERR- NoISA- VGA+ MAbort- >Reset- FastB2B+

00:07.0 ISA bridge: Intel Corp. 82371AB/EB/MB PIIX4 ISA (rev 02)
	Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
	Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
	Latency: 0

00:07.1 IDE interface: Intel Corp. 82371AB/EB/MB PIIX4 IDE (rev 01) (prog-if 80 [Master])
	Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
	Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
	Latency: 32
	Region 4: I/O ports at ffa0 [size=16]

00:07.2 USB Controller: Intel Corp. 82371AB/EB/MB PIIX4 USB (rev 01) (prog-if 00 [UHCI])
	Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
	Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
	Latency: 32
	Interrupt: pin D routed to IRQ 9
	Region 4: I/O ports at ef80 [size=32]

00:07.3 Bridge: Intel Corp. 82371AB/EB/MB PIIX4 ACPI (rev 03)
	Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
	Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
	Interrupt: pin ? routed to IRQ 9

00:09.0 Multimedia audio controller: Yamaha Corporation YMF-754 [DS-1E Audio Controller]
	Subsystem: NEC Corporation: Unknown device 80b5
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
	Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR+
	Latency: 32 (1250ns min, 6250ns max)
	Interrupt: pin A routed to IRQ 5
	Region 0: Memory at febf0000 (32-bit, non-prefetchable) [size=32K]
	Region 1: I/O ports at ef00 [size=64]
	Region 2: I/O ports at efe4 [size=4]
	Capabilities: [50] Power Management version 1
		Flags: PMEClk- DSI- D1- D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
		Status: D0 PME-Enable- DSel=0 DScale=0 PME-

00:0c.0 CardBus bridge: Texas Instruments PCI4450 PC card Cardbus Controller
	Subsystem: NEC Corporation: Unknown device 80b6
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
	Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
	Latency: 168, cache line size 08
	Interrupt: pin A routed to IRQ 10
	Region 0: Memory at 10000000 (32-bit, non-prefetchable) [size=4K]
	Bus: primary=00, secondary=02, subordinate=05, sec-latency=176
	Memory window 0: 10400000-107ff000 (prefetchable)
	Memory window 1: 10800000-10bff000
	I/O window 0: 000002c0-000002c3
	I/O window 1: 00001000-000010ff
	BridgeCtl: Parity- SERR- ISA- VGA- MAbort- >Reset+ 16bInt+ PostWrite+
	16-bit legacy interface ports at 0001

00:0c.1 CardBus bridge: Texas Instruments PCI4450 PC card Cardbus Controller
	Subsystem: NEC Corporation: Unknown device 80b6
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
	Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
	Latency: 168, cache line size 08
	Interrupt: pin B routed to IRQ 5
	Region 0: Memory at 10001000 (32-bit, non-prefetchable) [size=4K]
	Bus: primary=00, secondary=06, subordinate=09, sec-latency=176
	Memory window 0: 10c00000-10fff000 (prefetchable)
	Memory window 1: 11000000-113ff000
	I/O window 0: 00001400-000014ff
	I/O window 1: 00001800-000018ff
	BridgeCtl: Parity- SERR- ISA- VGA- MAbort- >Reset+ 16bInt+ PostWrite+
	16-bit legacy interface ports at 0001

00:0c.2 FireWire (IEEE 1394): Texas Instruments: Unknown device 8011 (prog-if 10 [OHCI])
	Subsystem: NEC Corporation: Unknown device 80b6
	Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR+ FastB2B-
	Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
	Latency: 32 (750ns min, 1000ns max), cache line size 08
	Interrupt: pin C routed to IRQ 5
	Region 0: Memory at febff000 (32-bit, non-prefetchable) [size=2K]
	Region 1: Memory at febf8000 (32-bit, non-prefetchable) [size=16K]
	Capabilities: [44] Power Management version 1
		Flags: PMEClk- DSI- D1- D2+ AuxCurrent=0mA PME(D0-,D1-,D2+,D3hot+,D3cold-)
		Status: D0 PME-Enable- DSel=0 DScale=0 PME-

00:0f.0 Communication controller: Lucent Microelectronics LT WinModem
	Subsystem: NEC Corporation: Unknown device 80a8
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
	Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
	Latency: 32 (63000ns min, 3500ns max)
	Interrupt: pin A routed to IRQ 5
	Region 0: Memory at febfff00 (32-bit, non-prefetchable) [size=256]
	Region 1: I/O ports at eff0 [size=8]
	Region 2: I/O ports at e800 [size=256]
	Capabilities: [f8] Power Management version 2
		Flags: PMEClk- DSI+ D1- D2- AuxCurrent=160mA PME(D0-,D1-,D2-,D3hot+,D3cold+)
		Status: D0 PME-Enable- DSel=0 DScale=0 PME-

01:00.0 VGA compatible controller: ATI Technologies Inc Rage Mobility P/M AGP 2x (rev 64) (prog-if 00 [VGA])
	Subsystem: NEC Corporation: Unknown device 80b7
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping+ SERR- FastB2B-
	Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
	Latency: 32 (2000ns min), cache line size 08
	Interrupt: pin A routed to IRQ 10
	Region 0: Memory at fd000000 (32-bit, non-prefetchable) [size=16M]
	Region 1: I/O ports at d800 [size=256]
	Region 2: Memory at feaff000 (32-bit, non-prefetchable) [size=4K]
	Expansion ROM at feac0000 [disabled] [size=128K]
	Capabilities: [50] AGP version 1.0
		Status: RQ=255 SBA+ 64bit- FW- Rate=x1,x2
		Command: RQ=0 SBA- AGP- 64bit- FW- Rate=<none>
	Capabilities: [5c] Power Management version 1
		Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
		Status: D0 PME-Enable- DSel=0 DScale=0 PME-


^ permalink raw reply	[flat|nested] 5+ messages in thread

* Re: 2.5.66-mm2-1 freezes solid after init PCMCIA
  2003-04-01 13:02   ` Felipe Alfaro Solana
@ 2003-04-01 19:46     ` Russell King
  2003-04-01 21:01       ` Felipe Alfaro Solana
  0 siblings, 1 reply; 5+ messages in thread
From: Russell King @ 2003-04-01 19:46 UTC (permalink / raw)
  To: Felipe Alfaro Solana; +Cc: LKML

On Tue, Apr 01, 2003 at 03:02:16PM +0200, Felipe Alfaro Solana wrote:
> OK, here we go...

I was thinking that it could be due to the pci changes - that's one of
the areas I've been working in recently which could have caused this.

However, I believe it is to do with the recent PCMCIA changes to use
the device model, and deadlock within the device model itself.

What basically seems to be happening is this:

- the ds module is inserted
- ds registers a driver model interface for pcmcia socket drivers,
  which takes the global devclass_sem.
- ds causes the pcmcia core to evaluate the status of the sockets, and
  perform "card insertion" processing if cards are present.
- this processing detects a cardbus card, and calls the cardbus code to
  scan pci devices, and add them to the device tree.
- each device gets passed to the device model's class layer, which tries
  to take devclass_sem.  But wait!  We've locked it while initialising
  the ds module -> deadlock.

I'm currently working on the card insertion/removal code which hopefully
should fix this.  However, it's not going to be immediately available,
so please be patient.

-- 
Russell King (rmk@arm.linux.org.uk)                The developer of ARM Linux
             http://www.arm.linux.org.uk/personal/aboutme.html


^ permalink raw reply	[flat|nested] 5+ messages in thread

* Re: 2.5.66-mm2-1 freezes solid after init PCMCIA
  2003-04-01 19:46     ` Russell King
@ 2003-04-01 21:01       ` Felipe Alfaro Solana
  0 siblings, 0 replies; 5+ messages in thread
From: Felipe Alfaro Solana @ 2003-04-01 21:01 UTC (permalink / raw)
  To: Russell King; +Cc: LKML

On Tue, 2003-04-01 at 21:46, Russell King wrote:
> I was thinking that it could be due to the pci changes - that's one of
> the areas I've been working in recently which could have caused this.
> 
> However, I believe it is to do with the recent PCMCIA changes to use
> the device model, and deadlock within the device model itself.
> 
> What basically seems to be happening is this:
> 
> - the ds module is inserted
> - ds registers a driver model interface for pcmcia socket drivers,
>   which takes the global devclass_sem.
> - ds causes the pcmcia core to evaluate the status of the sockets, and
>   perform "card insertion" processing if cards are present.
> - this processing detects a cardbus card, and calls the cardbus code to
>   scan pci devices, and add them to the device tree.
> - each device gets passed to the device model's class layer, which tries
>   to take devclass_sem.  But wait!  We've locked it while initialising
>   the ds module -> deadlock.
> 
> I'm currently working on the card insertion/removal code which hopefully
> should fix this.  However, it's not going to be immediately available,
> so please be patient.

Ok, Russell, take your time... Meanwhile, I'll stick with 2.5.66-mm1 and
will try all upcoming patches to see if/when the deadlock is fixed.
Thanks :-)

________________________________________________________________________
        Felipe Alfaro Solana
   Linux Registered User #287198
http://counter.li.org


^ permalink raw reply	[flat|nested] 5+ messages in thread

end of thread, other threads:[~2003-04-01 20:50 UTC | newest]

Thread overview: 5+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
2003-04-01 11:20 2.5.66-mm2-1 freezes solid after init PCMCIA Felipe Alfaro Solana
2003-04-01 11:53 ` Russell King
2003-04-01 13:02   ` Felipe Alfaro Solana
2003-04-01 19:46     ` Russell King
2003-04-01 21:01       ` Felipe Alfaro Solana

This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox