From: Martin Knoblauch <spamtrap@knobisoft.de>
To: "Rafael J. Wysocki" <rjw@sisk.pl>
Cc: linux-kernel@vger.kernel.org
Subject: Re: Booting 2.6.30-rc2-git7 very slow
Date: Wed, 22 Apr 2009 02:56:27 -0700 (PDT) [thread overview]
Message-ID: <106159.21345.qm@web32608.mail.mud.yahoo.com> (raw)
In-Reply-To: <200904212112.20278.rjw@sisk.pl>
> From: Rafael J. Wysocki <rjw@sisk.pl>
> To: Martin Knoblauch <spamtrap@knobisoft.de>
> Cc: linux-kernel@vger.kernel.org
> Sent: Tuesday, April 21, 2009 9:12:20 PM
> Subject: Re: Booting 2.6.30-rc2-git7 very slow
>
> On Tuesday 21 April 2009, Martin Knoblauch wrote:
> >
> > Hi, [please CC me on replies, as I am not subscribed]
> >
> > booting 2.6.30-rc2-git7 on a HP/DL380G3 (x86_64, RHEL4.3, 64 bit userspace)
> is much slower that it used to be. It seems I run into timeouts when [trying to]
> load intel and tg3 microcodes:
> >
> > [ 14.478892] platform microcode: firmware: requesting intel-ucode/0f-04-0a
> > [ 74.476741] platform microcode: firmware: requesting intel-ucode/0f-04-0a
> > [ 134.476638] platform microcode: firmware: requesting intel-ucode/0f-04-0a
> > [ 194.476637] platform microcode: firmware: requesting intel-ucode/0f-04-0a
> > [ 254.476493] Microcode Update Driver: v2.00 ,
> Peter Oruba
> > [ 254.718489] Microcode Update Driver: v2.00 removed.
> >
> > So, we see 60 seconds for eaoch of the CPUs
> >
> > [ 255.273426] tg3 0000:03:01.0: PME# disabled
> > [ 257.833769] tg3: eth0: Link is up at 1000 Mbps, full duplex.
> > [ 257.833775] tg3: eth0: Flow control is off for TX and off for RX.
> > [ 269.643973] tg3 0000:03:01.1: firmware: requesting tigon/tg3_tso.bin
> > [ 329.640456] eth1: Failed to load firmware "tigon/tg3_tso.bin"
> > [ 329.640463] eth1: TSO capability disabled.
> > [ 329.640487] tg3 0000:03:01.1: PME# disabled
> > [ 333.081753] tg3: eth1: Link is up at 1000 Mbps, full duplex.
> > [ 333.081759] tg3: eth1: Flow control is off for TX and off for RX.
> >
> > We see 60 seconds for eth1, complaining about a failed firmware load.
> > /lib/firmware/tigon/tg3_tso.bin does exist and is from the current
> > build.
>
> Do I assume correctly that 2.6.29 did not have this problem?
>
Just checked. 2.6.29 has exactely the same problem. 2.6.28.2 was OK. This is from the 2.6.29 boot:
[ 14.308340] platform microcode: firmware: requesting intel-ucode/0f-04-0a
[ 74.304612] platform microcode: firmware: requesting intel-ucode/0f-04-0a
[ 134.304651] platform microcode: firmware: requesting intel-ucode/0f-04-0a
[ 194.304638] platform microcode: firmware: requesting intel-ucode/0f-04-0a
[ 254.304597] Microcode Update Driver: v2.00 <tigran@aivazian.fsnet.co.uk>, Peter Oruba
[ 254.546200] Microcode Update Driver: v2.00 removed.
[ 255.088405] tg3 0000:03:01.0: PME# disabled
[ 257.669617] tg3: eth0: Link is up at 1000 Mbps, full duplex.
[ 257.669622] tg3: eth0: Flow control is off for TX and off for RX.
[ 269.456132] tg3 0000:03:01.1: firmware: requesting tigon/tg3_tso.bin
[ 329.456495] eth1: Failed to load firmware "tigon/tg3_tso.bin"
[ 329.456500] eth1: TSO capability disabled.
[ 329.456524] tg3 0000:03:01.1: PME# disabled
[ 332.921832] tg3: eth1: Link is up at 1000 Mbps, full duplex.
[ 332.921837] tg3: eth1: Flow control is off for TX and off for RX.
Cheers
Martin
next prev parent reply other threads:[~2009-04-22 9:56 UTC|newest]
Thread overview: 7+ messages / expand[flat|nested] mbox.gz Atom feed top
2009-04-21 14:21 Booting 2.6.30-rc2-git7 very slow Martin Knoblauch
2009-04-21 14:32 ` Martin Knoblauch
2009-04-21 19:12 ` Rafael J. Wysocki
2009-04-22 9:56 ` Martin Knoblauch [this message]
-- strict thread matches above, loose matches on Subject: below --
2009-04-22 6:06 Martin Knoblauch
2009-04-22 11:32 Martin Knoblauch
2009-04-22 16:55 Martin Knoblauch
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=106159.21345.qm@web32608.mail.mud.yahoo.com \
--to=spamtrap@knobisoft.de \
--cc=linux-kernel@vger.kernel.org \
--cc=rjw@sisk.pl \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox