From: Carlo <devel@integra-sc.it>
To: Bruce Allen <ballen@gravity.phys.uwm.edu>
Cc: dan carpenter <error27@email.com>,
Oleg Drokin <green@linuxhacker.ru>,
linux-kernel@vger.kernel.org
Subject: Re: Ooops with kernel 2.4.22 and reiserfs
Date: Sat, 27 Dec 2003 13:52:40 +0100 [thread overview]
Message-ID: <1072529558.21200.111.camel@atena> (raw)
In-Reply-To: <Pine.GSO.4.21.0312251946460.2554-100000@dirac.phys.uwm.edu>
Il ven, 2003-12-26 alle 02:47, Bruce Allen ha scritto:
> > > > C> hda: set_drive_speed_status: status=0x58 { DriveReady SeekComplete
> > > > C> DataRequest }
> > > > C> ide0: Drive 0 didn't accept speed setting. Oh, well.
> > > > C> hda: dma_intr: status=0x58 { DriveReady SeekComplete DataRequest }
> > > > C> hda: CHECK for good STATUS
> > > >
> >
> > I would check for SMARTerrors: smartctl -a /dev/hda
> > Also you could try running badblocks on the drive.
>
> Run some drive self-tests:
> smartctl -t long /dev/hda
> and let them complete, then look again at
> smartctl -a /dev/hda
>
smartctl version 5.26 Copyright (C) 2002-3 Bruce Allen
Home page is http://smartmontools.sourceforge.net/
=== START OF INFORMATION SECTION ===
Device Model: Maxtor 6Y120L0
Serial Number: Y3K9Q2GE
Firmware Version: YAR41BW0
Device is: In smartctl database [for details use: -P show]
ATA Version is: 7
ATA Standard is: ATA/ATAPI-7 T13 1532D revision 0
Local Time is: Sat Dec 27 13:42:50 2003 CET
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x80) Offline data collection activity
was
never started.
Auto Offline Data Collection:
Enabled.
Self-test execution status: ( 0) The previous self-test routine
completed
without error or no self-test
has ever
been run.
Total time to complete Offline
1data collection: ( 242) seconds.
Offline data collection
capabilities: (0x5b) SMART execute Offline immediate.
Auto Offline data collection
on/off support.
Suspend Offline collection upon
new
command.
Offline surface scan supported.
Self-test supported.
No Conveyance Self-test
supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
No General Purpose Logging
support.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 54) minutes.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE
UPDATED WHEN_FAILED RAW_VALUE
3 Spin_Up_Time 0x0027 204 204 063 Pre-fail
Always - 5709
4 Start_Stop_Count 0x0032 253 253 000 Old_age
Always - 28
5 Reallocated_Sector_Ct 0x0033 253 253 063 Pre-fail
Always - 0
6 Read_Channel_Margin 0x0001 253 253 100 Pre-fail
Offline - 0
7 Seek_Error_Rate 0x000a 253 252 000 Old_age
Always - 0
8 Seek_Time_Performance 0x0027 251 245 187 Pre-fail
Always - 57965
9 Power_On_Minutes 0x0032 250 250 000 Old_age
Always - 1064h+20m
10 Spin_Retry_Count 0x002b 253 252 157 Pre-fail
Always - 0
11 Calibration_Retry_Count 0x002b 253 252 223 Pre-fail
Always - 0
12 Power_Cycle_Count 0x0032 253 253 000 Old_age
Always - 53
192 Power-Off_Retract_Count 0x0032 253 253 000 Old_age
Always - 0
193 Load_Cycle_Count 0x0032 253 253 000 Old_age
Always - 0
194 Temperature_Celsius 0x0032 253 253 000 Old_age
Always - 31
195 Hardware_ECC_Recovered 0x000a 253 252 000 Old_age
Always - 6759
196 Reallocated_Event_Count 0x0008 253 253 000 Old_age
Offline - 0
197 Current_Pending_Sector 0x0008 253 253 000 Old_age
Offline - 0
198 Offline_Uncorrectable 0x0008 253 253 000 Old_age
Offline - 0
199 UDMA_CRC_Error_Count 0x0008 199 199 000 Old_age
Offline - 0
200 Multi_Zone_Error_Rate 0x000a 253 252 000 Old_age
Always - 0
201 Soft_Read_Error_Rate 0x000a 253 248 000 Old_age
Always - 2
202 TA_Increase_Count 0x000a 253 252 000 Old_age
Always - 0
203 Run_Out_Cancel 0x000b 253 252 180 Pre-fail
Always - 0
204 Shock_Count_Write_Opern 0x000a 253 252 000 Old_age
Always - 0
205 Shock_Rate_Write_Opern 0x000a 253 252 000 Old_age
Always - 0
207 Spin_High_Current 0x002a 253 252 000 Old_age
Always - 0
208 Spin_Buzz 0x002a 253 252 000 Old_age
Always - 0
209 Offline_Seek_Performnce 0x0024 197 197 000 Old_age
Offline - 0
99 Unknown_Attribute 0x0004 253 253 000 Old_age
Offline - 0
100 Unknown_Attribute 0x0004 253 253 000 Old_age
Offline - 0
101 Unknown_Attribute 0x0004 253 253 000 Old_age
Offline - 0
SMART Error Log Version: 1
No Errors Logged
SMART Self-test log structure revision number 1
Num Test_Description Status Remaining
LifeTime(hours) LBA_of_first_error
# 1 Extended offline Completed without error 00%
997 -
Some ideas??
Saluti Carlo!
> Cheers,
> Bruce
>
>
next prev parent reply other threads:[~2003-12-27 12:52 UTC|newest]
Thread overview: 12+ messages / expand[flat|nested] mbox.gz Atom feed top
2003-12-22 21:01 Ooops with kernel 2.4.22 and reiserfs Carlo
2003-12-22 22:05 ` Oleg Drokin
2003-12-23 10:04 ` Carlo
2003-12-23 15:20 ` Oleg Drokin
2003-12-23 18:17 ` Carlo
2003-12-25 12:34 ` dan carpenter
2003-12-26 1:47 ` Bruce Allen
2003-12-27 12:52 ` Carlo [this message]
2003-12-27 19:38 ` Bruce Allen
-- strict thread matches above, loose matches on Subject: below --
2003-12-22 18:49 Carlo
2003-12-23 10:39 ` Andre Hedrick
2003-12-23 17:45 ` Carlo
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1072529558.21200.111.camel@atena \
--to=devel@integra-sc.it \
--cc=ballen@gravity.phys.uwm.edu \
--cc=error27@email.com \
--cc=green@linuxhacker.ru \
--cc=linux-kernel@vger.kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox