[PATCH] [16/48] Suspend2 2.1.9.8 for 2.6.12: 406-dynamic-pageflags.patch

[Nigel Cunningham <nigel@suspend2.net>]

diff -ruNp 500-version-specific-i386.patch-old/arch/i386/power/Makefile 500-version-specific-i386.patch-new/arch/i386/power/Makefile
--- 500-version-specific-i386.patch-old/arch/i386/power/Makefile	2004-11-03 21:52:57.000000000 +1100
+++ 500-version-specific-i386.patch-new/arch/i386/power/Makefile	2005-07-04 23:14:19.000000000 +1000
@@ -1,2 +1,2 @@
-obj-$(CONFIG_PM)		+= cpu.o
+obj-$(CONFIG_PM)		+= cpu.o smp.o
 obj-$(CONFIG_SOFTWARE_SUSPEND)	+= swsusp.o
diff -ruNp 500-version-specific-i386.patch-old/arch/i386/power/smp.c 500-version-specific-i386.patch-new/arch/i386/power/smp.c
--- 500-version-specific-i386.patch-old/arch/i386/power/smp.c	1970-01-01 10:00:00.000000000 +1000
+++ 500-version-specific-i386.patch-new/arch/i386/power/smp.c	2005-07-04 23:14:19.000000000 +1000
@@ -0,0 +1,84 @@
+//#ifdef CONFIG_SMP
+#include <linux/suspend.h>
+#include <linux/irq.h>
+#include <asm/tlbflush.h>
+#include <asm/suspend2.h>
+
+extern atomic_t suspend_cpu_counter __nosavedata;
+unsigned char * my_saved_context __nosavedata;
+static unsigned long c_loops_per_jiffy_ref[NR_CPUS] __nosavedata;
+
+struct suspend2_saved_context suspend2_saved_contexts[NR_CPUS];
+struct suspend2_saved_context suspend2_saved_context;	/* temporary storage */
+cpumask_t saved_affinity[NR_IRQS];
+
+/*
+ * Save and restore processor state for secondary processors.
+ * IRQs (and therefore preemption) are already disabled 
+ * when we enter here (IPI).
+ */
+
+static volatile int loop __nosavedata;
+
+void __smp_suspend_lowlevel(void * data)
+{
+	__asm__( "movl %%ecx,%%cr3\n" ::"c"(__pa(swsusp_pg_dir)));
+
+	if (test_suspend_state(SUSPEND_NOW_RESUMING)) {
+		BUG_ON(!irqs_disabled());
+		kernel_fpu_begin();
+		c_loops_per_jiffy_ref[_smp_processor_id()] = current_cpu_data.loops_per_jiffy;
+		atomic_inc(&suspend_cpu_counter);
+
+		/* Only image copied back while we spin in this loop. Our
+		 * task info should not be looked at while this is happening
+		 * (which smp_processor_id() will do( */
+		while (test_suspend_state(SUSPEND_FREEZE_SMP)) { 
+			cpu_relax();
+			barrier();
+		}
+
+		while (atomic_read(&suspend_cpu_counter) != _smp_processor_id()) {
+			cpu_relax();
+			barrier();
+		}
+	       	my_saved_context = (unsigned char *) (suspend2_saved_contexts + _smp_processor_id());
+		for (loop = sizeof(struct suspend2_saved_context); loop--; loop)
+			*(((unsigned char *) &suspend2_saved_context) + loop - 1) = *(my_saved_context + loop - 1);
+		suspend2_restore_processor_context();
+		cpu_clear(_smp_processor_id(), per_cpu(cpu_tlbstate, _smp_processor_id()).active_mm->cpu_vm_mask);
+		load_cr3(swapper_pg_dir);
+		wbinvd();
+		__flush_tlb_all();
+		current_cpu_data.loops_per_jiffy = c_loops_per_jiffy_ref[_smp_processor_id()];
+		mtrr_restore_one_cpu();
+		atomic_dec(&suspend_cpu_counter);
+	} else {	/* suspending */
+		BUG_ON(!irqs_disabled());
+		/* 
+		 *Save context and go back to idling.
+		 * Note that we cannot leave the processor
+		 * here. It must be able to receive IPIs if
+		 * the LZF compression driver (eg) does a
+		 * vfree after compressing the kernel etc
+		 */
+		while (test_suspend_state(SUSPEND_FREEZE_SMP) &&
+			(atomic_read(&suspend_cpu_counter) != (_smp_processor_id() - 1))) {
+			cpu_relax();
+			barrier();
+		}
+		suspend2_save_processor_context();
+		my_saved_context = (unsigned char *) (suspend2_saved_contexts + _smp_processor_id());
+		for (loop = sizeof(struct suspend2_saved_context); loop--; loop)
+			*(my_saved_context + loop - 1) = *(((unsigned char *) &suspend2_saved_context) + loop - 1);
+		atomic_inc(&suspend_cpu_counter);
+		/* Now spin until the atomic copy of the kernel is made. */
+		while (test_suspend_state(SUSPEND_FREEZE_SMP)) {
+			cpu_relax();
+			barrier();
+		}
+		atomic_dec(&suspend_cpu_counter);
+		kernel_fpu_end();
+	}
+}
+//#endif
diff -ruNp 500-version-specific-i386.patch-old/include/asm-i386/suspend2.h 500-version-specific-i386.patch-new/include/asm-i386/suspend2.h
--- 500-version-specific-i386.patch-old/include/asm-i386/suspend2.h	1970-01-01 10:00:00.000000000 +1000
+++ 500-version-specific-i386.patch-new/include/asm-i386/suspend2.h	2005-07-05 23:56:41.000000000 +1000
@@ -0,0 +1,391 @@
+ /*
+  * Copyright 2003-2005 Nigel Cunningham <nigel@suspend2.net>
+  * Based on code
+  * Copyright 2001-2002 Pavel Machek <pavel@suse.cz>
+  * Based on code
+  * Copyright 2001 Patrick Mochel <mochel@osdl.org>
+  */
+#include <linux/irq.h>
+#include <asm/desc.h>
+#include <asm/i387.h>
+#include <asm/tlbflush.h>
+#include <asm/desc.h>
+#include <asm/suspend.h>
+#undef inline
+#define inline	__inline__ __attribute__((always_inline))
+
+/* image of the saved processor states */
+struct suspend2_saved_context {
+	u32 eax, ebx, ecx, edx;
+	u32 esp, ebp, esi, edi;
+	u16 es, fs, gs, ss;
+	u32 cr0, cr2, cr3, cr4;
+	u16 gdt_pad;
+	u16 gdt_limit;
+	u32 gdt_base;
+	u16 idt_pad;
+	u16 idt_limit;
+	u32 idt_base;
+	u16 ldt;
+	u16 tss;
+	u32 tr;
+	u32 safety;
+	u32 return_address;
+	u32 eflags;
+} __attribute__((packed));
+
+extern struct suspend2_saved_context suspend2_saved_context;	/* temporary storage */
+
+#ifdef CONFIG_MTRR
+/* MTRR functions */
+extern int mtrr_save(void);
+extern int mtrr_restore_one_cpu(void);
+extern void mtrr_restore_finish(void);
+#else
+#define mtrr_save() do { } while(0)
+#define mtrr_restore_one_cpu() do { } while(0)
+#define mtrr_restore_finish() do { } while(0)
+#endif
+		  
+#ifndef CONFIG_SMP
+#undef cpu_clear
+#define cpu_clear(a, b) do { } while(0)
+#endif
+
+extern struct suspend2_saved_context suspend2_saved_context;	/* temporary storage */
+
+/*
+ * save_processor_context
+ * 
+ * Save the state of the processor before we go to sleep.
+ *
+ * return_stack is the value of the stack pointer (%esp) as the caller sees it.
+ * A good way could not be found to obtain it from here (don't want to make _too_
+ * many assumptions about the layout of the stack this far down.) Also, the 
+ * handy little __builtin_frame_pointer(level) where level > 0, is blatantly 
+ * buggy - it returns the value of the stack at the proper location, not the 
+ * location, like it should (as of gcc 2.91.66)
+ * 
+ * Note that the context and timing of this function is pretty critical.
+ * With a minimal amount of things going on in the caller and in here, gcc
+ * does a good job of being just a dumb compiler.  Watch the assembly output
+ * if anything changes, though, and make sure everything is going in the right
+ * place. 
+ */
+static inline void suspend2_save_processor_context(void)
+{
+	kernel_fpu_begin();
+
+	/*
+	 * descriptor tables
+	 */
+	asm volatile ("sgdt (%0)" : "=m" (suspend2_saved_context.gdt_limit));
+	asm volatile ("sidt (%0)" : "=m" (suspend2_saved_context.idt_limit));
+	asm volatile ("sldt (%0)" : "=m" (suspend2_saved_context.ldt));
+	asm volatile ("str (%0)"  : "=m" (suspend2_saved_context.tr));
+
+	/*
+	 * save the general registers.
+	 * note that gcc has constructs to specify output of certain registers,
+	 * but they're not used here, because it assumes that you want to modify
+	 * those registers, so it tries to be smart and save them beforehand.
+	 * It's really not necessary, and kinda fishy (check the assembly output),
+	 * so it's avoided. 
+	 */
+	asm volatile ("movl %%esp, (%0)" : "=m" (suspend2_saved_context.esp));
+	asm volatile ("movl %%eax, (%0)" : "=m" (suspend2_saved_context.eax));
+	asm volatile ("movl %%ebx, (%0)" : "=m" (suspend2_saved_context.ebx));
+	asm volatile ("movl %%ecx, (%0)" : "=m" (suspend2_saved_context.ecx));
+	asm volatile ("movl %%edx, (%0)" : "=m" (suspend2_saved_context.edx));
+	asm volatile ("movl %%ebp, (%0)" : "=m" (suspend2_saved_context.ebp));
+	asm volatile ("movl %%esi, (%0)" : "=m" (suspend2_saved_context.esi));
+	asm volatile ("movl %%edi, (%0)" : "=m" (suspend2_saved_context.edi));
+
+	/*
+	 * segment registers
+	 */
+	asm volatile ("movw %%es, %0" : "=r" (suspend2_saved_context.es));
+	asm volatile ("movw %%fs, %0" : "=r" (suspend2_saved_context.fs));
+	asm volatile ("movw %%gs, %0" : "=r" (suspend2_saved_context.gs));
+	asm volatile ("movw %%ss, %0" : "=r" (suspend2_saved_context.ss));
+
+	/*
+	 * control registers 
+	 */
+	asm volatile ("movl %%cr0, %0" : "=r" (suspend2_saved_context.cr0));
+	asm volatile ("movl %%cr2, %0" : "=r" (suspend2_saved_context.cr2));
+	asm volatile ("movl %%cr3, %0" : "=r" (suspend2_saved_context.cr3));
+	asm volatile ("movl %%cr4, %0" : "=r" (suspend2_saved_context.cr4));
+
+	/*
+	 * eflags
+	 */
+	asm volatile ("pushfl ; popl (%0)" : "=m" (suspend2_saved_context.eflags));
+}
+
+static void fix_processor_context(void)
+{
+	int nr = _smp_processor_id();
+	struct tss_struct * t = &per_cpu(init_tss,nr);
+
+	set_tss_desc(nr,t);	/* This just modifies memory; should not be neccessary. But... This is neccessary, because 386 hardware has concept of busy tsc or some similar stupidity. */
+        per_cpu(cpu_gdt_table,nr)[GDT_ENTRY_TSS].b &= 0xfffffdff;
+
+	load_TR_desc();
+
+	load_LDT(&current->active_mm->context);	/* This does lldt */
+
+	/*
+	 * Now maybe reload the debug registers
+	 */
+	if (current->thread.debugreg[7]){
+                loaddebug(&current->thread, 0);
+                loaddebug(&current->thread, 1);
+                loaddebug(&current->thread, 2);
+                loaddebug(&current->thread, 3);
+                /* no 4 and 5 */
+                loaddebug(&current->thread, 6);
+                loaddebug(&current->thread, 7);
+	}
+
+}
+
+static void do_fpu_end(void)
+{
+        /* restore FPU regs if necessary */
+	/* Do it out of line so that gcc does not move cr0 load to some stupid place */
+        kernel_fpu_end();
+}
+
+/*
+ * restore_processor_context
+ * 
+ * Restore the processor context as it was before we went to sleep
+ * - descriptor tables
+ * - control registers
+ * - segment registers
+ * - flags
+ * 
+ * Note that it is critical that this function is declared inline.  
+ * It was separated out from restore_state to make that function
+ * a little clearer, but it needs to be inlined because we won't have a
+ * stack when we get here (so we can't push a return address).
+ */
+static inline void restore_processor_context(void)
+{
+	/*
+	 * first restore %ds, so we can access our data properly
+	 */
+	asm volatile (".align 4");
+	asm volatile ("movw %0, %%ds" :: "r" ((u16)__KERNEL_DS));
+
+
+	/*
+	 * control registers
+	 */
+	asm volatile ("movl %0, %%cr4" :: "r" (suspend2_saved_context.cr4));
+	asm volatile ("movl %0, %%cr3" :: "r" (suspend2_saved_context.cr3));
+	asm volatile ("movl %0, %%cr2" :: "r" (suspend2_saved_context.cr2));
+	asm volatile ("movl %0, %%cr0" :: "r" (suspend2_saved_context.cr0));
+
+	/*
+	 * segment registers
+	 */
+	asm volatile ("movw %0, %%es" :: "r" (suspend2_saved_context.es));
+	asm volatile ("movw %0, %%fs" :: "r" (suspend2_saved_context.fs));
+	asm volatile ("movw %0, %%gs" :: "r" (suspend2_saved_context.gs));
+	asm volatile ("movw %0, %%ss" :: "r" (suspend2_saved_context.ss));
+
+	/*
+	 * the other general registers
+	 *
+	 * note that even though gcc has constructs to specify memory 
+	 * input into certain registers, it will try to be too smart
+	 * and save them at the beginning of the function.  This is esp.
+	 * bad since we don't have a stack set up when we enter, and we 
+	 * want to preserve the values on exit. So, we set them manually.
+	 */
+	asm volatile ("movl %0, %%esp" :: "m" (suspend2_saved_context.esp));
+	asm volatile ("movl %0, %%ebp" :: "m" (suspend2_saved_context.ebp));
+	asm volatile ("movl %0, %%eax" :: "m" (suspend2_saved_context.eax));
+	asm volatile ("movl %0, %%ebx" :: "m" (suspend2_saved_context.ebx));
+	asm volatile ("movl %0, %%ecx" :: "m" (suspend2_saved_context.ecx));
+	asm volatile ("movl %0, %%edx" :: "m" (suspend2_saved_context.edx));
+	asm volatile ("movl %0, %%esi" :: "m" (suspend2_saved_context.esi));
+	asm volatile ("movl %0, %%edi" :: "m" (suspend2_saved_context.edi));
+
+	/*
+	 * now restore the descriptor tables to their proper values
+	 * ltr is done in fix_processor_context().
+	 */
+
+	asm volatile ("lgdt (%0)" :: "m" (suspend2_saved_context.gdt_limit));
+	asm volatile ("lidt (%0)" :: "m" (suspend2_saved_context.idt_limit));
+	asm volatile ("lldt (%0)" :: "m" (suspend2_saved_context.ldt));
+
+	fix_processor_context();
+
+	/*
+	 * the flags
+	 */
+	asm volatile ("pushl %0 ; popfl" :: "m" (suspend2_saved_context.eflags));
+
+	do_fpu_end();
+}
+
+#if defined(CONFIG_SUSPEND2) || defined(CONFIG_SMP)
+extern atomic_t suspend_cpu_counter __nosavedata;
+extern unsigned char * my_saved_context __nosavedata;
+static unsigned long c_loops_per_jiffy_ref[NR_CPUS] __nosavedata;
+#endif
+
+#ifdef CONFIG_SUSPEND2
+#ifndef CONFIG_SMP
+extern unsigned long loops_per_jiffy;
+volatile static unsigned long cpu_khz_ref __nosavedata = 0;
+#endif
+
+/* 
+ * APIC support: These routines save the APIC
+ * configuration for the CPU on which they are
+ * being executed
+ */
+extern void suspend_apic_save_state(void);
+extern void suspend_apic_reload_state(void);
+
+#ifdef CONFIG_SMP
+/* ------------------------------------------------
+ * BEGIN Irq affinity code, based on code from LKCD.
+ *
+ * IRQ affinity support:
+ * Save and restore IRQ affinities, and set them
+ * all to CPU 0.
+ *
+ * Section between dashes taken from LKCD code.
+ * Perhaps we should be working toward a shared library
+ * of such routines for kexec, lkcd, software suspend
+ * and whatever other similar projects there are?
+ */
+
+extern irq_desc_t irq_desc[];
+extern cpumask_t irq_affinity[];
+extern cpumask_t saved_affinity[NR_IRQS];
+
+/*
+ * Routine to save the old irq affinities and change affinities of all irqs to
+ * the dumping cpu.
+ */
+static void save_and_set_irq_affinity(void)
+{
+	int i;
+	int cpu = _smp_processor_id();
+
+	memcpy(saved_affinity, irq_affinity, NR_IRQS * sizeof(cpumask_t));
+	for (i = 0; i < NR_IRQS; i++) {
+		if (irq_desc[i].handler == NULL)
+			continue;
+		irq_affinity[i] = cpumask_of_cpu(cpu);
+		if (irq_desc[i].handler->set_affinity != NULL)
+			irq_desc[i].handler->set_affinity(i, irq_affinity[i]);
+	}
+}
+
+/*
+ * Restore old irq affinities.
+ */
+static void reset_irq_affinity(void)
+{
+	int i;
+
+	memcpy(irq_affinity, saved_affinity, NR_IRQS * sizeof(cpumask_t));
+	for (i = 0; i < NR_IRQS; i++) {
+		if (irq_desc[i].handler == NULL)
+			continue;
+		if (irq_desc[i].handler->set_affinity != NULL)
+			irq_desc[i].handler->set_affinity(i, irq_affinity[i]);
+	}
+}
+
+/*
+ * END of IRQ affinity code, based on LKCD code.
+ * -----------------------------------------------------------------
+ */
+#else
+#define save_and_set_irq_affinity() do { } while(0)
+#define reset_irq_affinity() do { } while(0)
+#endif
+
+static inline void suspend2_pre_copy(void)
+{
+	/*
+	 * Save the irq affinities before we freeze the
+	 * other processors!
+	 */
+	save_and_set_irq_affinity();
+	mtrr_save();
+}
+
+static inline void suspend2_post_copy(void)
+{
+}
+
+static inline void suspend2_pre_copyback(void)
+{
+	/* We want to run from swsusp_pg_dir, since swsusp_pg_dir is stored in constant
+	 * place in memory 
+	 */
+
+        __asm__( "movl %%ecx,%%cr3\n" ::"c"(__pa(swsusp_pg_dir)));
+	/* Send all IRQs to CPU 0. We will replace the saved affinities
+	 * with the suspend-time ones when we copy the original kernel
+	 * back in place
+	 */
+	save_and_set_irq_affinity();
+	
+	c_loops_per_jiffy_ref[_smp_processor_id()] = current_cpu_data.loops_per_jiffy;
+#ifndef CONFIG_SMP
+	cpu_khz_ref = cpu_khz;
+	c_loops_per_jiffy_ref[_smp_processor_id()] = loops_per_jiffy;
+#endif
+	
+}
+
+static inline void suspend2_restore_processor_context(void)
+{
+	restore_processor_context();
+}
+	
+static inline void suspend2_flush_caches(void)
+{
+	cpu_clear(_smp_processor_id(), per_cpu(cpu_tlbstate, _smp_processor_id()).active_mm->cpu_vm_mask);
+	wbinvd();
+	__flush_tlb_all();
+	
+}
+
+static inline void suspend2_post_copyback(void)
+{
+	mtrr_restore_one_cpu();
+
+	/* Get other CPUs to restore their contexts and flush their tlbs. */
+	clear_suspend_state(SUSPEND_FREEZE_SMP);
+	
+	do {
+		cpu_relax();
+		barrier();
+	} while (atomic_read(&suspend_cpu_counter));
+	mtrr_restore_finish();
+	
+	BUG_ON(!irqs_disabled());
+
+	/* put the irq affinity tables back */
+	reset_irq_affinity();
+	
+	current_cpu_data.loops_per_jiffy = c_loops_per_jiffy_ref[_smp_processor_id()];
+#ifndef CONFIG_SMP
+	loops_per_jiffy = c_loops_per_jiffy_ref[_smp_processor_id()];
+	cpu_khz = cpu_khz_ref;
+#endif
+}
+
+#endif
diff -ruNp 500-version-specific-i386.patch-old/include/asm-i386/suspend.h 500-version-specific-i386.patch-new/include/asm-i386/suspend.h
--- 500-version-specific-i386.patch-old/include/asm-i386/suspend.h	2005-06-20 11:47:15.000000000 +1000
+++ 500-version-specific-i386.patch-new/include/asm-i386/suspend.h	2005-07-04 23:14:19.000000000 +1000
@@ -3,6 +3,7 @@
  * Based on code
  * Copyright 2001 Patrick Mochel <mochel@osdl.org>
  */
+#include <linux/errno.h>
 #include <asm/desc.h>
 #include <asm/i387.h>