translated ATA stat/err 0x51/0c to ... PDC20376 (FastTrak 376) related cold freezes

translated ATA stat/err 0x51/0c to ... PDC20376 (FastTrak 376) related cold freezes

[Soeren Sonnenburg]

Dear all,

I just upgraded to using 2 sata disks (both seagate drives
ST3400832AS and ST3750640AS) on this asus a7v8x on-board promise fastrak
376 (PDC20376) controller. However, as soon as I do a lot of io (cp some
G of files) I get swamped in 

ata1: translated ATA stat/err 0x51/0c to SCSI SK/ASC/ASCQ 0xb/00/00
ata1: status=0x51 { DriveReady SeekComplete Error }
ata1: error=0x0c { DriveStatusError }
ata2: translated ATA stat/err 0x51/0c to SCSI SK/ASC/ASCQ 0xb/00/00
ata2: status=0x51 { DriveReady SeekComplete Error }
ata2: error=0x0c { DriveStatusError }
...

messages. For that it is enough to do it on a single drive or copy from
drive to drive. This is on kernel 2.6.17.4, but I remember (when I was
still using a single drive) this very same output to happen on 2.6.15.

Can anyone translate these dubious error messages to me ?

Here are more details about the system:

- the sata_promise driver version 1.04 is used

- relevant dmesg output:
libata version 1.20 loaded.
sata_promise 0000:00:08.0: version 1.04
ACPI: PCI Interrupt 0000:00:08.0[A] -> GSI 17 (level, low) -> IRQ 17
ata1: SATA max UDMA/133 cmd 0xF8822200 ctl 0xF8822238 bmdma 0x0 irq 17
ata2: SATA max UDMA/133 cmd 0xF8822280 ctl 0xF88222B8 bmdma 0x0 irq 17
ata1: SATA link up 1.5 Gbps (SStatus 113)
ata1: dev 0 cfg 49:2f00 82:346b 83:7d01 84:4023 85:3469 86:3c01 87:4023 88:007f
ata1: dev 0 ATA-7, max UDMA/133, 781422768 sectors: LBA48
ata1: dev 0 configured for UDMA/133
scsi0 : sata_promise
ata2: SATA link up 1.5 Gbps (SStatus 113)
ata2: dev 0 cfg 49:2f00 82:346b 83:7d01 84:4023 85:3469 86:3c01 87:4023 88:007f
ata2: dev 0 ATA-7, max UDMA/133, 1465149168 sectors: LBA48
ata2: dev 0 configured for UDMA/133
scsi1 : sata_promise
  Vendor: ATA       Model: ST3400832AS       Rev: 3.01
  Type:   Direct-Access                      ANSI SCSI revision: 05
  Vendor: ATA       Model: ST3750640AS       Rev: 3.AA
  Type:   Direct-Access                      ANSI SCSI revision: 05
SCSI device sda: 781422768 512-byte hdwr sectors (400088 MB)
sda: Write Protect is off
sda: Mode Sense: 00 3a 00 00
SCSI device sda: drive cache: write back
SCSI device sda: 781422768 512-byte hdwr sectors (400088 MB)
sda: Write Protect is off
sda: Mode Sense: 00 3a 00 00
SCSI device sda: drive cache: write back
 sda: unknown partition table
sd 0:0:0:0: Attached scsi disk sda
SCSI device sdb: 1465149168 512-byte hdwr sectors (750156 MB)
sdb: Write Protect is off
sdb: Mode Sense: 00 3a 00 00
SCSI device sdb: drive cache: write back
SCSI device sdb: 1465149168 512-byte hdwr sectors (750156 MB)
sdb: Write Protect is off
sdb: Mode Sense: 00 3a 00 00
SCSI device sdb: drive cache: write back
 sdb: unknown partition table
sd 1:0:0:0: Attached scsi disk sdb


# cat /proc/interrupts
           CPU0
  0:    1513605    IO-APIC-edge  timer
  1:        469    IO-APIC-edge  i8042
  8:          4    IO-APIC-edge  rtc
  9:          0   IO-APIC-level  acpi
 14:      85189    IO-APIC-edge  ide0
 15:      14736    IO-APIC-edge  ide1
 16:      88324   IO-APIC-level  ide2
 17:     234771   IO-APIC-level  libata
 18:     277667   IO-APIC-level  ehci_hcd:usb1, uhci_hcd:usb2, uhci_hcd:usb3, uhci_hcd:usb4
 19:      14909   IO-APIC-level  fcpci, eth0
 20:          0   IO-APIC-level  saa7146 (0)
 21:          0   IO-APIC-level  VIA8233
NMI:    1516297
LOC:    1515188
ERR:          0
MIS:          0

# lspci
0000:00:00.0 Host bridge: VIA Technologies, Inc. VT8377 [KT400/KT600 AGP] Host Bridge
0000:00:01.0 PCI bridge: VIA Technologies, Inc. VT8235 PCI Bridge
0000:00:07.0 FireWire (IEEE 1394): VIA Technologies, Inc. IEEE 1394 Host Controller (rev 46)
0000:00:08.0 RAID bus controller: Promise Technology, Inc. PDC20376 (FastTrak 376) (rev 02)
0000:00:09.0 Ethernet controller: Broadcom Corporation BCM4401 100Base-T (rev 01)
0000:00:0a.0 Multimedia controller: Philips Semiconductors SAA7146 (rev 01)
0000:00:0b.0 Network controller: AVM Audiovisuelles MKTG & Computer System GmbH A1 ISDN [Fritz] (rev 02)
0000:00:0c.0 Ethernet controller: Intel Corp. 82541GI/PI Gigabit Ethernet Controller
0000:00:0f.0 Unknown mass storage controller: Triones Technologies, Inc. HPT366/368/370/370A/372 (rev 04)
0000:00:10.0 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (rev 80)
0000:00:10.1 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (rev 80)
0000:00:10.2 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (rev 80)
0000:00:10.3 USB Controller: VIA Technologies, Inc. USB 2.0 (rev 82)
0000:00:11.0 ISA bridge: VIA Technologies, Inc. VT8235 ISA Bridge
0000:00:11.1 IDE interface: VIA Technologies, Inc. VT82C586A/B/VT82C686/A/B/VT823x/A/C PIPC Bus Master IDE (rev 06)
0000:00:11.5 Multimedia audio controller: VIA Technologies, Inc. VT8233/A/8235/8237 AC97 Audio Controller (rev 50)
0000:01:00.0 VGA compatible controller: ATI Technologies Inc RV280 [Radeon 9200] (rev 01)
0000:01:00.1 Display controller: ATI Technologies Inc RV280 [Radeon 9200] (Secondary) (rev 01)

Any ideas/need more info -> let me know.

Thanks in advance,
Soeren
-- 
Sometimes, there's a moment as you're waking, when you become aware of
the real world around you, but you're still dreaming.

Re: translated ATA stat/err 0x51/0c to ... PDC20376 (FastTrak 376) related cold freezes

[Tejun Heo]

Soeren Sonnenburg wrote:
> Dear all,
> 
> I just upgraded to using 2 sata disks (both seagate drives
> ST3400832AS and ST3750640AS) on this asus a7v8x on-board promise fastrak
> 376 (PDC20376) controller. However, as soon as I do a lot of io (cp some
> G of files) I get swamped in 
> 
> ata1: translated ATA stat/err 0x51/0c to SCSI SK/ASC/ASCQ 0xb/00/00
> ata1: status=0x51 { DriveReady SeekComplete Error }
> ata1: error=0x0c { DriveStatusError }
> ata2: translated ATA stat/err 0x51/0c to SCSI SK/ASC/ASCQ 0xb/00/00
> ata2: status=0x51 { DriveReady SeekComplete Error }
> ata2: error=0x0c { DriveStatusError }
> ...

Is the system usable after these messages?

> messages. For that it is enough to do it on a single drive or copy from
> drive to drive. This is on kernel 2.6.17.4, but I remember (when I was
> still using a single drive) this very same output to happen on 2.6.15.
> 
> Can anyone translate these dubious error messages to me ?
> 
> Here are more details about the system:
> 
> - the sata_promise driver version 1.04 is used

Can you give a shot at 2.6.18-rc4?

-- 
tejun

Re: translated ATA stat/err 0x51/0c to ... PDC20376 (FastTrak 376) related cold freezes

[Soeren Sonnenburg]

On Sun, 2006-08-27 at 18:37 +0900, Tejun Heo wrote:
> Soeren Sonnenburg wrote:
> > Dear all,
> > 
> > I just upgraded to using 2 sata disks (both seagate drives
> > ST3400832AS and ST3750640AS) on this asus a7v8x on-board promise fastrak
> > 376 (PDC20376) controller. However, as soon as I do a lot of io (cp some
> > G of files) I get swamped in 
> > 
> > ata1: translated ATA stat/err 0x51/0c to SCSI SK/ASC/ASCQ 0xb/00/00
> > ata1: status=0x51 { DriveReady SeekComplete Error }
> > ata1: error=0x0c { DriveStatusError }
> > ata2: translated ATA stat/err 0x51/0c to SCSI SK/ASC/ASCQ 0xb/00/00
> > ata2: status=0x51 { DriveReady SeekComplete Error }
> > ata2: error=0x0c { DriveStatusError }
> > ...
> 
> Is the system usable after these messages?

Yes, however I got cold freezes from (time to time) after a while...

> > messages. For that it is enough to do it on a single drive or copy from
> > drive to drive. This is on kernel 2.6.17.4, but I remember (when I was
> > still using a single drive) this very same output to happen on 2.6.15.
> > 
> > Can anyone translate these dubious error messages to me ?
> > 
> > Here are more details about the system:
> > 
> > - the sata_promise driver version 1.04 is used
> 
> Can you give a shot at 2.6.18-rc4?

I will, though I don't see much changes in that driver...

Soeren
-- 
Sometimes, there's a moment as you're waking, when you become aware of
the real world around you, but you're still dreaming.

Re: translated ATA stat/err 0x51/0c to ... PDC20376 (FastTrak 376) related cold freezes

[Tejun Heo]

Soeren Sonnenburg wrote:
> On Sun, 2006-08-27 at 18:37 +0900, Tejun Heo wrote:
>> Soeren Sonnenburg wrote:
>>> Dear all,
>>>
>>> I just upgraded to using 2 sata disks (both seagate drives
>>> ST3400832AS and ST3750640AS) on this asus a7v8x on-board promise fastrak
>>> 376 (PDC20376) controller. However, as soon as I do a lot of io (cp some
>>> G of files) I get swamped in 
>>>
>>> ata1: translated ATA stat/err 0x51/0c to SCSI SK/ASC/ASCQ 0xb/00/00
>>> ata1: status=0x51 { DriveReady SeekComplete Error }
>>> ata1: error=0x0c { DriveStatusError }
>>> ata2: translated ATA stat/err 0x51/0c to SCSI SK/ASC/ASCQ 0xb/00/00
>>> ata2: status=0x51 { DriveReady SeekComplete Error }
>>> ata2: error=0x0c { DriveStatusError }
>>> ...
>> Is the system usable after these messages?
> 
> Yes, however I got cold freezes from (time to time) after a while...

I see.  your drive is reporting error for some reason and libata is 
failing to recover.

>>> messages. For that it is enough to do it on a single drive or copy from
>>> drive to drive. This is on kernel 2.6.17.4, but I remember (when I was
>>> still using a single drive) this very same output to happen on 2.6.15.
>>>
>>> Can anyone translate these dubious error messages to me ?
>>>
>>> Here are more details about the system:
>>>
>>> - the sata_promise driver version 1.04 is used
>> Can you give a shot at 2.6.18-rc4?
> 
> I will, though I don't see much changes in that driver...

Ah.. right.  sata_promise isn't converted to new EH yet.  There's no 
reason to try -rc4.  Please stand by.

Thanks.

-- 
tejun

Re: translated ATA stat/err 0x51/0c to ... PDC20376 (FastTrak 376) related cold freezes

[Tejun Heo]

[cc'ing Jeff & linux-ide, quoting whole body]

Jeff, here's a EH test case for sata_promise, just in case you missed 
this thread.

Tejun Heo wrote:
> Soeren Sonnenburg wrote:
>> On Sun, 2006-08-27 at 18:37 +0900, Tejun Heo wrote:
>>> Soeren Sonnenburg wrote:
>>>> Dear all,
>>>>
>>>> I just upgraded to using 2 sata disks (both seagate drives
>>>> ST3400832AS and ST3750640AS) on this asus a7v8x on-board promise 
>>>> fastrak
>>>> 376 (PDC20376) controller. However, as soon as I do a lot of io (cp 
>>>> some
>>>> G of files) I get swamped in
>>>> ata1: translated ATA stat/err 0x51/0c to SCSI SK/ASC/ASCQ 0xb/00/00
>>>> ata1: status=0x51 { DriveReady SeekComplete Error }
>>>> ata1: error=0x0c { DriveStatusError }
>>>> ata2: translated ATA stat/err 0x51/0c to SCSI SK/ASC/ASCQ 0xb/00/00
>>>> ata2: status=0x51 { DriveReady SeekComplete Error }
>>>> ata2: error=0x0c { DriveStatusError }
>>>> ...
>>> Is the system usable after these messages?
>>
>> Yes, however I got cold freezes from (time to time) after a while...
> 
> I see.  your drive is reporting error for some reason and libata is 
> failing to recover.
> 
>>>> messages. For that it is enough to do it on a single drive or copy from
>>>> drive to drive. This is on kernel 2.6.17.4, but I remember (when I was
>>>> still using a single drive) this very same output to happen on 2.6.15.
>>>>
>>>> Can anyone translate these dubious error messages to me ?
>>>>
>>>> Here are more details about the system:
>>>>
>>>> - the sata_promise driver version 1.04 is used
>>> Can you give a shot at 2.6.18-rc4?
>>
>> I will, though I don't see much changes in that driver...
> 
> Ah.. right.  sata_promise isn't converted to new EH yet.  There's no 
> reason to try -rc4.  Please stand by.
> 
> Thanks.

-- 
tejun