From: Tony Lindgren <tony@atomide.com>
To: linux-kernel@vger.kernel.org
Cc: Kyungmin Park <kyungmin.park@samsung.com>,
Tony Lindgren <tony@atomide.com>
Subject: [PATCH 5/18] ARM: OMAP: Board Apollon update, fix boot
Date: Mon, 9 Apr 2007 17:30:48 -0400 [thread overview]
Message-ID: <1176154277435-git-send-email-tony@atomide.com> (raw)
In-Reply-To: <11761542731458-git-send-email-tony@atomide.com>
From: Kyungmin Park <kyungmin.park@samsung.com>
Update Apollon board init to initialize NAND, USB,
and LEDs. Also configure GPMC memory for smc91x Ethernet.
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
---
arch/arm/mach-omap2/board-apollon.c | 99 +++++++++++++++++++++++++++++++---
1 files changed, 90 insertions(+), 9 deletions(-)
--- a/arch/arm/mach-omap2/board-apollon.c
+++ b/arch/arm/mach-omap2/board-apollon.c
@@ -25,6 +25,8 @@
#include <linux/irq.h>
#include <linux/interrupt.h>
#include <linux/delay.h>
+#include <linux/leds.h>
+#include <linux/irq.h>
#include <asm/hardware.h>
#include <asm/mach-types.h>
@@ -32,10 +34,12 @@
#include <asm/mach/flash.h>
#include <asm/arch/gpio.h>
+#include <asm/arch/led.h>
#include <asm/arch/mux.h>
#include <asm/arch/usb.h>
#include <asm/arch/board.h>
#include <asm/arch/common.h>
+#include <asm/arch/gpmc.h>
#include "prcm-regs.h"
/* LED & Switch macros */
@@ -46,6 +50,9 @@
#define SW_UP_GPIO17 17
#define SW_DOWN_GPIO58 58
+#define APOLLON_FLASH_CS 0
+#define APOLLON_ETH_CS 1
+
static struct mtd_partition apollon_partitions[] = {
{
.name = "X-Loader + U-Boot",
@@ -85,10 +92,10 @@ static struct flash_platform_data apollon_flash_data = {
.nr_parts = ARRAY_SIZE(apollon_partitions),
};
-static struct resource apollon_flash_resource = {
- .start = APOLLON_CS0_BASE,
- .end = APOLLON_CS0_BASE + SZ_128K,
- .flags = IORESOURCE_MEM,
+static struct resource apollon_flash_resource[] = {
+ [0] = {
+ .flags = IORESOURCE_MEM,
+ },
};
static struct platform_device apollon_onenand_device = {
@@ -97,14 +104,24 @@ static struct platform_device apollon_onenand_device = {
.dev = {
.platform_data = &apollon_flash_data,
},
- .num_resources = ARRAY_SIZE(&apollon_flash_resource),
- .resource = &apollon_flash_resource,
+ .num_resources = ARRAY_SIZE(apollon_flash_resource),
+ .resource = apollon_flash_resource,
};
+static void __init apollon_flash_init(void)
+{
+ unsigned long base;
+
+ if (gpmc_cs_request(APOLLON_FLASH_CS, SZ_128K, &base) < 0) {
+ printk(KERN_ERR "Cannot request OneNAND GPMC CS\n");
+ return;
+ }
+ apollon_flash_resource[0].start = base;
+ apollon_flash_resource[0].end = base + SZ_128K - 1;
+}
+
static struct resource apollon_smc91x_resources[] = {
[0] = {
- .start = APOLLON_ETHR_START, /* Physical */
- .end = APOLLON_ETHR_START + 0xf,
.flags = IORESOURCE_MEM,
},
[1] = {
@@ -126,14 +143,51 @@ static struct platform_device apollon_lcd_device = {
.id = -1,
};
+static struct omap_led_config apollon_led_config[] = {
+ {
+ .cdev = {
+ .name = "apollon:led0",
+ },
+ .gpio = LED0_GPIO13,
+ },
+ {
+ .cdev = {
+ .name = "apollon:led1",
+ },
+ .gpio = LED1_GPIO14,
+ },
+ {
+ .cdev = {
+ .name = "apollon:led2",
+ },
+ .gpio = LED2_GPIO15,
+ },
+};
+
+static struct omap_led_platform_data apollon_led_data = {
+ .nr_leds = ARRAY_SIZE(apollon_led_config),
+ .leds = apollon_led_config,
+};
+
+static struct platform_device apollon_led_device = {
+ .name = "omap-led",
+ .id = -1,
+ .dev = {
+ .platform_data = &apollon_led_data,
+ },
+};
+
static struct platform_device *apollon_devices[] __initdata = {
&apollon_onenand_device,
&apollon_smc91x_device,
&apollon_lcd_device,
+ &apollon_led_device,
};
static inline void __init apollon_init_smc91x(void)
{
+ unsigned long base;
+
/* Make sure CS1 timings are correct */
GPMC_CONFIG1_1 = 0x00011203;
GPMC_CONFIG2_1 = 0x001f1f01;
@@ -141,13 +195,20 @@ static inline void __init apollon_init_smc91x(void)
GPMC_CONFIG4_1 = 0x1c091c09;
GPMC_CONFIG5_1 = 0x041f1f1f;
GPMC_CONFIG6_1 = 0x000004c4;
- GPMC_CONFIG7_1 = 0x00000f40 | (APOLLON_CS1_BASE >> 24);
+
+ if (gpmc_cs_request(APOLLON_ETH_CS, SZ_16M, &base) < 0) {
+ printk(KERN_ERR "Failed to request GPMC CS for smc91x\n");
+ return;
+ }
+ apollon_smc91x_resources[0].start = base + 0x300;
+ apollon_smc91x_resources[0].end = base + 0x30f;
udelay(100);
omap_cfg_reg(W4__24XX_GPIO74);
if (omap_request_gpio(APOLLON_ETHR_GPIO_IRQ) < 0) {
printk(KERN_ERR "Failed to request GPIO%d for smc91x IRQ\n",
APOLLON_ETHR_GPIO_IRQ);
+ gpmc_cs_free(APOLLON_ETH_CS);
return;
}
omap_set_gpio_direction(APOLLON_ETHR_GPIO_IRQ, 1);
@@ -175,6 +236,13 @@ static struct omap_mmc_config apollon_mmc_config __initdata = {
},
};
+static struct omap_usb_config apollon_usb_config __initdata = {
+ .register_dev = 1,
+ .hmc_mode = 0x14, /* 0:dev 1:host1 2:disable */
+
+ .pins[0] = 6,
+};
+
static struct omap_lcd_config apollon_lcd_config __initdata = {
.ctrl_name = "internal",
};
@@ -182,6 +250,7 @@ static struct omap_lcd_config apollon_lcd_config __initdata = {
static struct omap_board_config_kernel apollon_config[] = {
{ OMAP_TAG_UART, &apollon_uart_config },
{ OMAP_TAG_MMC, &apollon_mmc_config },
+ { OMAP_TAG_USB, &apollon_usb_config },
{ OMAP_TAG_LCD, &apollon_lcd_config },
};
@@ -250,10 +319,22 @@ static void __init apollon_sw_init(void)
return;
}
+static void __init apollon_usb_init(void)
+{
+ /* USB device */
+ /* DEVICE_SUSPEND */
+ omap_cfg_reg(P21_242X_GPIO12);
+ omap_request_gpio(12);
+ omap_set_gpio_direction(12, 0); /* OUT */
+ omap_set_gpio_dataout(12, 0);
+}
+
static void __init omap_apollon_init(void)
{
apollon_led_init();
apollon_sw_init();
+ apollon_flash_init();
+ apollon_usb_init();
/* REVISIT: where's the correct place */
omap_cfg_reg(W19_24XX_SYS_NIRQ);
--
1.4.4.2
next prev parent reply other threads:[~2007-04-09 21:42 UTC|newest]
Thread overview: 19+ messages / expand[flat|nested] mbox.gz Atom feed top
2007-04-09 21:30 [PATCH 0/18] ARM: OMAP: Updates for OMAP2 common code Tony Lindgren
2007-04-09 21:30 ` [PATCH 1/18] ARM: OMAP2: Place SMS and SDRC into smart idle mode Tony Lindgren
2007-04-09 21:30 ` [PATCH 2/18] ARM: OMAP2: Force APLLs always active Tony Lindgren
2007-04-09 21:30 ` [PATCH 3/18] ARM: OMAP: Enable serial idling and wakeup features Tony Lindgren
2007-04-09 21:30 ` [PATCH 4/18] ARM: OMAP: Optimize INTC register accesses and enable autoidling Tony Lindgren
2007-04-09 21:30 ` Tony Lindgren [this message]
2007-04-09 21:30 ` [PATCH 6/18] ARM: OMAP: omap2/memory.c compile fixes Tony Lindgren
2007-04-09 21:30 ` [PATCH 7/18] ARM: OMAP: 24xx pinmux updates Tony Lindgren
2007-04-09 21:30 ` [PATCH 8/18] ARM: OMAP: omap2/gpmc updates Tony Lindgren
2007-04-09 21:30 ` [PATCH 9/18] ARM: OMAP: abstract debug card setup (smc, leds) Tony Lindgren
2007-04-09 21:30 ` [PATCH 10/18] ARM: OMAP: Add minimal OMAP2430 support Tony Lindgren
2007-04-09 21:30 ` [PATCH 11/18] ARM: OMAP: Tabify mux.c Tony Lindgren
2007-04-09 21:30 ` [PATCH 12/18] ARM: OMAP: TUSB EVM init Tony Lindgren
2007-04-09 21:30 ` [PATCH 13/18] ARM: OMAP: Merge gpmc changes from N800 tree Tony Lindgren
2007-04-09 21:30 ` [PATCH 14/18] ARM: OMAP: Merge driver headers " Tony Lindgren
2007-04-09 21:30 ` [PATCH 15/18] ARM: OMAP: Merge PM code " Tony Lindgren
2007-04-09 21:30 ` [PATCH 16/18] ARM: OMAP: 243x: Add mappings for SDRC and SMS Tony Lindgren
2007-04-09 21:31 ` [PATCH 17/18] ARM: OMAP: Device init for OMAP24xx Enhanced Audio Controller Tony Lindgren
2007-04-09 21:31 ` [PATCH 18/18] ARM: OMAP: Fix PRCM base register usage for 243x Tony Lindgren
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1176154277435-git-send-email-tony@atomide.com \
--to=tony@atomide.com \
--cc=kyungmin.park@samsung.com \
--cc=linux-kernel@vger.kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox