Re: [RESEND PATCH v1 4/4] clk: rockchip: rk3036: fix and add node id for emac clock

Xing Zheng
2016-01-06T13:06:15Z

Hi Heiko,

On 2016年01月02日 10:34, Xing Zheng wrote:
> Hi Heiko,
> Thank you for your patch, I will apply and test it later.
>
> Thanks.
>
>> 在 2016年1月2日，06:10，Heiko Stübner <heiko@sntech.de> 写道：
>>
>> Hi Xing,
>>
>> Am Dienstag, 29. Dezember 2015, 10:34:09 schrieb Xing Zheng:
>>> On 2015年12月29日 09:59, Yakir Yang wrote:
>>>> On 12/28/2015 08:41 PM, Heiko Stübner wrote:
>>>>> Am Montag, 28. Dezember 2015, 17:03:53 schrieb Xing Zheng:
>>>>>> Due to referred old version TRM, there is incorrect emac clock node,
>>>>>> we should fix it. The SEL_21_9 is the parent of SEL_21_4.
>>>>>>
>>>>>> In the emac driver, we need to refer HCLK_MAC, and because There are
>>>>>> only 3PLLs (APLL/GPLL/DPLL) on the rk3036, most clock are under the
>>>>>> GPLL, and it is unable to provide the accurate rate for mac_ref which
>>>>>> need to 50MHz probability, we should let it under the APLL and are
>>>>>> able to set the freq which integer multiples of 50MHz, so we add these
>>>>>> emac node for reference.
>>>>> I don't really follow here. While I do understand that the emac needs
>>>>> 50MHz, I
>>>>> don't think using the APLL as source is helpful.
>>>>>
>>>>> The APLL is the main clocksource for the cpu-cores, including frequency
>>>>> scaling, and while it currently only lists 816MHz as sole frequency,
>>>>> you're
>>>>> pretty much guaranteed to not get your correct multiple of 50MHz from
>>>>> there
>>>>> either. And limiting the cpu to just do 600MHz to get the mac working
>>>>> sounds
>>>>> pretty bad ;-) .
>>>>>
>>>>>
>>>>> In the rk3036 cru-node the gpll gets set to 594MHz. Is there a
>>>>> special reason
>>>>> why it needs to be 594MHz and cannot be a round 600MHz? Because that
>>>>> would
>>>>> also provide your 50MHz-multiple nicely.
>>>> Yes, this magic 594MHz would help to support the standard HDMI
>>>> resolutions, here are the math:
>>>>
>>>> 1920x1080-60Hz DCLK = 148.5MHz = 594MHz / 4
>>>> 1280x720-60Hz DCLK = 74.25MHz = 594MHz / 8
>>>> 720x480-60Hz DCLK = 27MHz = 594MHz / 22
>>>>
>>>> Thanks,
>>>> - Yakir
>>> Thanks Yakir.
>>>
>>> Hi Heiko,
>>> From the above, do you have better idea for the RK3036's emac without
>>> ext-oscillator?
>> During the last days I did play a bit with the clock framework. As I don't
>> have a Kylin (or any rk3036) board, I did build a test-case with pclk_cpu on
>> the rk3188 (which can be affected by the armclk if not reparented to the
>> gpll), which got sucessfully adapted to get back to (or near) the originally
>> requested frequency.
>>
>> So ideally you could roll back your mux/div split here and try the attached
>> diff. In theory it should help :-) .
>> As can be seen by the FIXMEs, not fully finished, but I'd like to determine if
>> it fixes the issue at least.
>>
>>
>> Heiko
>> <clk-keep-req-rate.diff>

I tested your patch just now, it seems to work well. I will do more tests.

Thank you. :-)