From: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
To: Takashi Iwai <tiwai@suse.de>
Cc: linux-kernel@vger.kernel.org
Subject: Re: Is devm_* broken ?
Date: Wed, 15 Jul 2015 19:27:42 +0300 [thread overview]
Message-ID: <12287299.f8AJmpnxZx@avalon> (raw)
In-Reply-To: <s5hmvyxl7f1.wl-tiwai@suse.de>
On Wednesday 15 July 2015 18:20:02 Takashi Iwai wrote:
> On Wed, 15 Jul 2015 18:08:34 +0200, Laurent Pinchart wrote:
> > On Wednesday 15 July 2015 17:51:28 Takashi Iwai wrote:
> > > On Wed, 15 Jul 2015 00:34:53 +0200, Laurent Pinchart wrote:
> > > > Hello,
> > > >
> > > > I came to realize not too long ago that the following sequence of
> > > > events will lead to a crash with any platform driver that uses devm_*
> > > > and creates device nodes.
> > > >
> > > > 1. Get a platform device bound it its driver
> > > > 2. Open the corresponding device node in userspace and keep it open
> > > > 3. Unbind the platform device from its driver through sysfs
> > > >
> > > > echo <device-name> > /sys/bus/platform/drivers/<driver-name>/unbind
> > > >
> > > > (or for hotpluggable devices just unplug the device)
> > > >
> > > > 4. Close the device node
> > > > 5. Enjoy the fireworks
> > > >
> > > > While having a device node open prevents modules from being unloaded,
> > > > it doesn't prevent devices from being unbound from drivers. If the
> > > > driver uses devm_* helpers to allocate memory the memory will be freed
> > > > when the device is unbound from the driver, but that memory will still
> > > > be used by any operation touching an open device node.
> > > >
> > > > Is devm_* inherently broken ? It's so widely used, tell me I'm missing
> > > > something obvious.
> > >
> > > I don't think this is specific to devm_*() but it's about the resource
> > > management in general. After bus or driver's remove callback, all
> > > device resources that have been assigned by the driver are supposed to
> > > be freed, or ready to be freed.
> >
> > The remove callback notifies drivers that the device has been removed and
> > that it's time to clean up. However, drivers have no control over
> > userspace, so they can't force applications to close all open file
> > handles, unmap memory and otherwise free all device-related resources
> > immediately and synchronously. The best a driver can do is prevent any
> > new reference to a resource from being taken by userspace (returning an
> > error from open() for instance) and wait until all existing references
> > get released before finally freeing resources. This is where devm_* hurts
> > as a driver can't delay freeing resources until after all references held
> > by userspace are released.
>
> Right, and this is what ALSA drivers does in general.
Does that mean that an ALSA driver that uses devm_* will crash if the device
is unbound from the driver (possibly because it gets disconnected) while
userspace uses the ALSA device ? Isn't that considered as an issue ?
> > If I were to switch the uvcvideo driver from kzalloc to devm_kzalloc it
> > would crash if the webcam gets disconnected while userspace has the V4L2
> > device node open.
>
> The disconnection is a bit different story, but I see your concern.
>From a resources release point of view disconnection and unbind are similar.
--
Regards,
Laurent Pinchart
next prev parent reply other threads:[~2015-07-15 16:27 UTC|newest]
Thread overview: 14+ messages / expand[flat|nested] mbox.gz Atom feed top
2015-07-14 22:34 Is devm_* broken ? Laurent Pinchart
2015-07-15 15:51 ` Takashi Iwai
2015-07-15 16:08 ` Laurent Pinchart
2015-07-15 16:20 ` Takashi Iwai
2015-07-15 16:27 ` Laurent Pinchart [this message]
2015-07-15 16:34 ` Takashi Iwai
2015-07-28 14:10 ` Laurent Pinchart
2015-07-15 17:00 ` Dan Williams
2015-07-15 18:03 ` Tejun Heo
2015-07-28 14:16 ` Laurent Pinchart
2015-07-28 15:22 ` Tejun Heo
2015-07-28 17:05 ` Laurent Pinchart
2015-08-04 19:56 ` Pavel Machek
2015-08-04 21:26 ` Dmitry Torokhov
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=12287299.f8AJmpnxZx@avalon \
--to=laurent.pinchart@ideasonboard.com \
--cc=linux-kernel@vger.kernel.org \
--cc=tiwai@suse.de \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox