From: Stefani Seibold <stefani@seibold.net>
To: Dominik Brodowski <linux@dominikbrodowski.net>
Cc: Matthew Wilcox <matthew@wil.cx>,
linux-kernel <linux-kernel@vger.kernel.org>,
Linux PCI <linux-pci@vger.kernel.org>,
Jesse Barnes <jbarnes@virtuousgeek.org>,
"Rafael J. Wysocki" <rjw@sisk.pl>
Subject: Re: PCI Express-to-PCI Bridge: yenta_cardbus no bus associated!
Date: Mon, 26 Oct 2009 08:27:53 +0100 [thread overview]
Message-ID: <1256542073.4187.14.camel@wall-e> (raw)
In-Reply-To: <20091025083841.GA12526@isilmar.linta.de>
> >
> > Okay, i tried it again with 'pci=assign-bussed'. All i get is a
> >
> > decode_hpp: Could not get hotplug parameters. Use defaults
> >
> > thats all. The express-card will not be detected.
>
> I assume the "d" at the end was just a typo -- and "lspci -vvv" looks the
> same?
>
Yes, this was a typo. Here are the diff's of dmesg and lspci -vvv with
and without "pci=assign-busses" after inserting the express card.
dmesg without 'pci=assign-busses':
----------------------------------
pci 0000:0e:00.0: supports D1 D2
pci 0000:0f:00.0: reg 10 32bit mmio: [0x000000-0x000fff]
pci 0000:0f:00.0: supports D1 D2
pci 0000:0f:00.0: PME# supported from D0 D1 D2 D3hot D3cold
pci 0000:0f:00.0: PME# disabled
pci 0000:0e:00.0: bridge io port: [0x00-0xfff]
pci 0000:0e:00.0: bridge 32bit mmio: [0x000000-0x0fffff]
pci 0000:0e:00.0: bridge 64bit mmio pref: [0x000000-0x0fffff]
ACPI: Delete PCI Interrupt Routing Table for 0000:0f
pci 0000:0e:00.0: PCI bridge, secondary bus 0000:0f
pci 0000:0e:00.0: IO window: disabled
pci 0000:0e:00.0: MEM window: 0xf1c00000-0xf1cfffff
pci 0000:0e:00.0: PREFETCH window: disabled
decode_hpp: Could not get hotplug parameters. Use defaults
pci 0000:0e:00.0: enabling device (0000 -> 0002)
pci 0000:0e:00.0: setting latency timer to 64
yenta_cardbus 0000:0f:00.0: no bus associated! (try 'pci=assign-busses')
CE: hpet increasing min_delta_ns to 50624 nsec
lspci -vvv without 'pci=assign-busses':
---------------------------------------
0e:00.0 PCI bridge: Texas Instruments XIO2000(A)/XIO2200(A) PCI Express-to-PCI Bridge (rev 03) (prog-if 00 [Normal decode])
Physical Slot: 1
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=0e, secondary=0f, subordinate=0f, sec-latency=64
I/O behind bridge: 0000f000-00000fff
Memory behind bridge: f1c00000-f1cfffff
Prefetchable memory behind bridge: 00000000fff00000-00000000000fffff
Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Bridge: PM- B3+
Capabilities: [60] MSI: Enable- Count=1/16 Maskable- 64bit+
Address: 0000000000000000 Data: 0000
Capabilities: [80] Subsystem: Device 5678:1234
Capabilities: [90] Express (v1) PCI/PCI-X Bridge, MSI 00
DevCap: MaxPayload 512 bytes, PhantFunc 0, Latency L0s <64ns, L1 <1us
ExtTag- AttnBtn- AttnInd- PwrInd- RBE- FLReset-
DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop+ BrConfRtry-
MaxPayload 128 bytes, MaxReadReq 512 bytes
DevSta: CorrErr- UncorrErr+ FatalErr- UnsuppReq- AuxPwr+ TransPend-
LnkCap: Port #0, Speed 2.5GT/s, Width x1, ASPM L0s L1, Latency L0 <64ns, L1 <1us
ClockPM- Surprise- LLActRep- BwNot-
LnkCtl: ASPM Disabled; Disabled- Retrain- CommClk-
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
Capabilities: [100] Advanced Error Reporting
UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
UEMsk: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
UESvrt: DLP+ SDES- TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt- RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol-
CESta: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr-
CEMsk: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr-
AERCap: First Error Pointer: 00, GenCap+ CGenEn- ChkCap+ ChkEn-
0f:00.0 CardBus bridge: Texas Instruments PCIxx12 Cardbus Controller
Subsystem: Texas Instruments Device ac48
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Interrupt: pin A routed to IRQ 255
Region 0: Memory at f1c00000 (32-bit, non-prefetchable) [disabled] [size=4K]
Bus: primary=00, secondary=00, subordinate=00, sec-latency=0
Memory window 0: 00000000-00000000 [disabled] (prefetchable)
Memory window 1: 00000000-00000000 [disabled] (prefetchable)
I/O window 0: 00000000-00000003 [disabled]
I/O window 1: 00000000-00000003 [disabled]
BridgeCtl: Parity- SERR- ISA- VGA- MAbort- >Reset+ 16bInt- PostWrite-
16-bit legacy interface ports at 0001
dmesg with 'pci=assign-busses':
-------------------------------
pci 0000:05:00.0: supports D1 D2
decode_hpp: Could not get hotplug parameters. Use defaults
lspci -vvv with 'pci=assign-busses':
------------------------------------
05:00.0 PCI bridge: Texas Instruments XIO2000(A)/XIO2200(A) PCI Express-to-PCI Bridge (rev 03) (prog-if 00 [Normal decode])
Physical Slot: 1
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Bus: primary=00, secondary=00, subordinate=00, sec-latency=64
I/O behind bridge: 00000000-00000fff
Memory behind bridge: 00000000-000fffff
Prefetchable memory behind bridge: 0000000000000000-00000000000fffff
Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Bridge: PM- B3+
Capabilities: [60] MSI: Enable- Count=1/16 Maskable- 64bit+
Address: 0000000000000000 Data: 0000
Capabilities: [80] Subsystem: Device 5678:1234
Capabilities: [90] Express (v1) PCI/PCI-X Bridge, MSI 00
DevCap: MaxPayload 512 bytes, PhantFunc 0, Latency L0s <64ns, L1 <1us
ExtTag- AttnBtn- AttnInd- PwrInd- RBE- FLReset-
DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop+ BrConfRtry-
MaxPayload 128 bytes, MaxReadReq 512 bytes
DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr+ TransPend-
LnkCap: Port #0, Speed 2.5GT/s, Width x1, ASPM L0s L1, Latency L0 <64ns, L1 <1us
ClockPM- Surprise- LLActRep- BwNot-
LnkCtl: ASPM Disabled; Disabled- Retrain- CommClk-
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
Capabilities: [100] Advanced Error Reporting
UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
UEMsk: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
UESvrt: DLP+ SDES- TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt- RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol-
CESta: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr-
CEMsk: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr-
AERCap: First Error Pointer: 00, GenCap+ CGenEn- ChkCap+ ChkEn-
Greetings,
Stefani
prev parent reply other threads:[~2009-10-26 7:28 UTC|newest]
Thread overview: 7+ messages / expand[flat|nested] mbox.gz Atom feed top
2009-09-29 18:23 PCI Express-to-PCI Bridge: yenta_cardbus no bus associated! Stefani Seibold
2009-09-29 23:15 ` Rafael J. Wysocki
2009-10-24 14:03 ` Stefani Seibold
2009-10-24 20:34 ` Matthew Wilcox
2009-10-25 8:10 ` Stefani Seibold
2009-10-25 8:38 ` Dominik Brodowski
2009-10-26 7:27 ` Stefani Seibold [this message]
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1256542073.4187.14.camel@wall-e \
--to=stefani@seibold.net \
--cc=jbarnes@virtuousgeek.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-pci@vger.kernel.org \
--cc=linux@dominikbrodowski.net \
--cc=matthew@wil.cx \
--cc=rjw@sisk.pl \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox