[PATCHv2 0/3] for-next: Add all twl4030 regulators to RegFW

[PATCHv2 0/3] for-next: Add all twl4030 regulators to RegFW

[Juha Keski-Saari]

Hello Liam,

This series is a revision of an earlier patch which was sent before.
The previous patch was split and now these changes are against voltage-2.6
tree, branch for-next.

There are two new modification. So now this series contains:
- Add all twl4030 regulators to the RegFW and 
- make sure the REMAP configuration of each regulator is as after reset. 
- Also defines critical regulators as always-on since it is not feasible
to allow them to be disabled in a case where the RegFW is used

These are only modifications on the twl4030 regulator driver. Changes to
the mfd driver will be sent separately

BR,

Juha Keski-Saari (3):
  twl4030-regulator: Add all TWL regulators to twreg_info
  Reset REMAP configuration in regulator probe
  Define critical regulators as always_on

 drivers/regulator/twl4030-regulator.c |   48 +++++++++++++++++++++++---------
 1 files changed, 34 insertions(+), 14 deletions(-)

[PATCHv2 1/3] twl4030-regulator: Add all TWL regulators to twreg_info

[Juha Keski-Saari]

Define all twl4030 regulators in the twlreg_info table, along with
appropriate VSEL tables for adjustable regulators

Signed-off-by: Juha Keski-Saari <ext-juha.1.keski-saari@nokia.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
---
 drivers/regulator/twl4030-regulator.c |   31 +++++++++++++++++--------------
 1 files changed, 17 insertions(+), 14 deletions(-)

diff --git a/drivers/regulator/twl4030-regulator.c b/drivers/regulator/twl4030-regulator.c
index 9365140..75da6af 100644
--- a/drivers/regulator/twl4030-regulator.c
+++ b/drivers/regulator/twl4030-regulator.c
@@ -260,7 +260,18 @@ static const u16 VSIM_VSEL_table[] = {
 static const u16 VDAC_VSEL_table[] = {
 	1200, 1300, 1800, 1800,
 };
-
+static const u16 VDD1_VSEL_table[] = {
+	800, 1450,
+};
+static const u16 VDD2_VSEL_table[] = {
+	800, 1450, 1500,
+};
+static const u16 VIO_VSEL_table[] = {
+	1800, 1850,
+};
+static const u16 VINTANA2_VSEL_table[] = {
+	2500, 2750,
+};
 
 static int twl4030ldo_list_voltage(struct regulator_dev *rdev, unsigned index)
 {
@@ -390,27 +401,19 @@ static struct regulator_ops twl4030fixed_ops = {
  * software control over them after boot.
  */
 static struct twlreg_info twl4030_regs[] = {
-	TWL_ADJUSTABLE_LDO(VAUX1, 0x17, 1),
-	TWL_ADJUSTABLE_LDO(VAUX2_4030, 0x1b, 2),
-	TWL_ADJUSTABLE_LDO(VAUX2, 0x1b, 2),
-	TWL_ADJUSTABLE_LDO(VAUX3, 0x1f, 3),
 	TWL_ADJUSTABLE_LDO(VAUX4, 0x23, 4),
 	TWL_ADJUSTABLE_LDO(VMMC1, 0x27, 5),
 	TWL_ADJUSTABLE_LDO(VMMC2, 0x2b, 6),
-	/*
 	TWL_ADJUSTABLE_LDO(VPLL1, 0x2f, 7),
-	*/
 	TWL_ADJUSTABLE_LDO(VPLL2, 0x33, 8),
 	TWL_ADJUSTABLE_LDO(VSIM, 0x37, 9),
 	TWL_ADJUSTABLE_LDO(VDAC, 0x3b, 10),
-	/*
-	TWL_ADJUSTABLE_LDO(VINTANA1, 0x3f, 11),
+	TWL_FIXED_LDO(VINTANA1, 0x3f, 1500, 11),
 	TWL_ADJUSTABLE_LDO(VINTANA2, 0x43, 12),
-	TWL_ADJUSTABLE_LDO(VINTDIG, 0x47, 13),
-	TWL_SMPS(VIO, 0x4b, 14),
-	TWL_SMPS(VDD1, 0x55, 15),
-	TWL_SMPS(VDD2, 0x63, 16),
-	 */
+	TWL_FIXED_LDO(VINTDIG, 0x47, 1500, 13),
+	TWL_ADJUSTABLE_LDO(VIO, 0x4b, 14),
+	TWL_ADJUSTABLE_LDO(VDD1, 0x55, 15),
+	TWL_ADJUSTABLE_LDO(VDD2, 0x63, 16),
 	TWL_FIXED_LDO(VUSB1V5, 0x71, 1500, 17),
 	TWL_FIXED_LDO(VUSB1V8, 0x74, 1800, 18),
 	TWL_FIXED_LDO(VUSB3V1, 0x77, 3100, 19),
-- 
1.6.3.3

[PATCHv2 2/3] Reset REMAP configuration in regulator probe

[Juha Keski-Saari]

This patch makes the probe recover the regulator REMAP configuration into
the state it is on reset to make sure the RegFW has proper control over
the regulator states

Signed-off-by: Juha Keski-Saari <ext-juha.1.keski-saari@nokia.com>
---
 drivers/regulator/twl4030-regulator.c |    9 +++++++++
 1 files changed, 9 insertions(+), 0 deletions(-)

diff --git a/drivers/regulator/twl4030-regulator.c b/drivers/regulator/twl4030-regulator.c
index 75da6af..7029fb9 100644
--- a/drivers/regulator/twl4030-regulator.c
+++ b/drivers/regulator/twl4030-regulator.c
@@ -420,6 +420,13 @@ static struct twlreg_info twl4030_regs[] = {
 	/* VUSBCP is managed *only* by the USB subchip */
 };
 
+static const u8 REG_REMAP_table[] = {
+	0x08, 0x08, 0x08, 0x08, 0x00, 0x08, 0x08,
+	0x08, 0x00, 0x08, 0x08, 0x08, 0x08, 0x08,
+	0x08, 0x08, 0x08, 0x08, 0x08, 0x08, 0x08,
+	0x08,
+};
+
 static int twl4030reg_probe(struct platform_device *pdev)
 {
 	int				i;
@@ -458,6 +465,8 @@ static int twl4030reg_probe(struct platform_device *pdev)
 	}
 	platform_set_drvdata(pdev, rdev);
 
+       twl4030reg_write(info, VREG_REMAP, REG_REMAP_table[pdev->id]);
+
 	/* NOTE:  many regulators support short-circuit IRQs (presentable
 	 * as REGULATOR_OVER_CURRENT notifications?) configured via:
 	 *  - SC_CONFIG
-- 
1.6.3.3

[PATCHv2 3/3] Define critical regulators as always_on

[Juha Keski-Saari]

Defines VIO, VDD1, VDD2, VPLL1 and VINT* regulators as always_on by default
since they are critical to TWL and its master's functionality and should
be on in all cases where RegFW is used

Signed-off-by: Juha Keski-Saari <ext-juha.1.keski-saari@nokia.com>
---
 drivers/regulator/twl4030-regulator.c |    8 ++++++++
 1 files changed, 8 insertions(+), 0 deletions(-)

diff --git a/drivers/regulator/twl4030-regulator.c b/drivers/regulator/twl4030-regulator.c
index 7029fb9..af53f35 100644
--- a/drivers/regulator/twl4030-regulator.c
+++ b/drivers/regulator/twl4030-regulator.c
@@ -456,6 +456,14 @@ static int twl4030reg_probe(struct platform_device *pdev)
 	c->valid_ops_mask &= REGULATOR_CHANGE_VOLTAGE
 				| REGULATOR_CHANGE_MODE
 				| REGULATOR_CHANGE_STATUS;
+	if (pdev->id == TWL4030_REG_VIO ||
+		pdev->id == TWL4030_REG_VDD1 ||
+		pdev->id == TWL4030_REG_VDD2 ||
+		pdev->id == TWL4030_REG_VPLL1 ||
+		pdev->id == TWL4030_REG_VINTANA1 ||
+		pdev->id == TWL4030_REG_VINTANA2 ||
+		pdev->id == TWL4030_REG_VINTDIG)
+		c->always_on = true;
 
 	rdev = regulator_register(&info->desc, &pdev->dev, initdata, info);
 	if (IS_ERR(rdev)) {
-- 
1.6.3.3

Re: [PATCHv2 3/3] Define critical regulators as always_on

[Mark Brown]

On Wed, Nov 25, 2009 at 12:04:55PM +0200, Juha Keski-Saari wrote:

> +	if (pdev->id == TWL4030_REG_VIO ||
> +		pdev->id == TWL4030_REG_VDD1 ||
> +		pdev->id == TWL4030_REG_VDD2 ||
> +		pdev->id == TWL4030_REG_VPLL1 ||
> +		pdev->id == TWL4030_REG_VINTANA1 ||
> +		pdev->id == TWL4030_REG_VINTANA2 ||
> +		pdev->id == TWL4030_REG_VINTDIG)
> +		c->always_on = true;

This would be a bit clearer and much more idiomatic as a switch
statement.

Re: [PATCHv2 3/3] Define critical regulators as always_on

[Juha Keski-Saari]

On Wed, 2009-11-25 at 11:14 +0100, ext Mark Brown wrote:
> On Wed, Nov 25, 2009 at 12:04:55PM +0200, Juha Keski-Saari wrote:
> 
> > +	if (pdev->id == TWL4030_REG_VIO ||
> > +		pdev->id == TWL4030_REG_VDD1 ||
> > +		pdev->id == TWL4030_REG_VDD2 ||
> > +		pdev->id == TWL4030_REG_VPLL1 ||
> > +		pdev->id == TWL4030_REG_VINTANA1 ||
> > +		pdev->id == TWL4030_REG_VINTANA2 ||
> > +		pdev->id == TWL4030_REG_VINTDIG)
> > +		c->always_on = true;
> 
> This would be a bit clearer and much more idiomatic as a switch
> statement.

A switch statement sounds like a better idea, yes. Below is a version
that implements that change.

>From 469f1f3fac05a740484cb32469b64aae424ba4de Mon Sep 17 00:00:00 2001
From: Juha Keski-Saari <ext-juha.1.keski-saari@nokia.com>
Date: Wed, 25 Nov 2009 11:10:35 +0200
Subject: [PATCHv3 3/3] Define critical regulators as always_on

Defines VIO, VDD1, VDD2, VPLL1 and VINT* regulators as always_on by
default
since they are critical to TWL and its master's functionality and should
be on in all cases where RegFW is used

Signed-off-by: Juha Keski-Saari <ext-juha.1.keski-saari@nokia.com>
---
 drivers/regulator/twl4030-regulator.c |   13 +++++++++++++
 1 files changed, 13 insertions(+), 0 deletions(-)

diff --git a/drivers/regulator/twl4030-regulator.c
b/drivers/regulator/twl4030-regulator.c
index 7029fb9..02100bc 100644
--- a/drivers/regulator/twl4030-regulator.c
+++ b/drivers/regulator/twl4030-regulator.c
@@ -456,6 +456,19 @@ static int twl4030reg_probe(struct platform_device
*pdev)
 	c->valid_ops_mask &= REGULATOR_CHANGE_VOLTAGE
 				| REGULATOR_CHANGE_MODE
 				| REGULATOR_CHANGE_STATUS;
+	switch(pdev->id) {
+		case TWL4030_REG_VIO:
+		case TWL4030_REG_VDD1:
+		case TWL4030_REG_VDD2:
+		case TWL4030_REG_VPLL1:
+		case TWL4030_REG_VINTANA1:
+		case TWL4030_REG_VINTANA2:
+		case TWL4030_REG_VINTDIG:
+			c->always_on = true;
+			break;
+		default:
+			break;
+	}
 
 	rdev = regulator_register(&info->desc, &pdev->dev, initdata, info);
 	if (IS_ERR(rdev)) {
-- 
1.6.3.3

Re: [PATCHv2 3/3] Define critical regulators as always_on

[Mark Brown]

On Wed, Nov 25, 2009 at 12:29:59PM +0200, Juha Keski-Saari wrote:

> +		case TWL4030_REG_VINTDIG:
> +			c->always_on = true;
> +			break;

One other thing I noticed having seen the MFD series - is this going to
build without the separate MFD patch you've posted?

Re: [PATCHv2 3/3] Define critical regulators as always_on

[Juha Keski-Saari]

On Wed, 2009-11-25 at 12:13 +0100, ext Mark Brown wrote:
> On Wed, Nov 25, 2009 at 12:29:59PM +0200, Juha Keski-Saari wrote:
> 
> > +		case TWL4030_REG_VINTDIG:
> > +			c->always_on = true;
> > +			break;
> 
> One other thing I noticed having seen the MFD series - is this going to
> build without the separate MFD patch you've posted?

Yes, the changes to twl4030-regulator.c compile without the changes the
MFD patch set makes to twl4030-core.c and twl4030.h

Re: [PATCHv2 1/3] twl4030-regulator: Add all TWL regulators to twreg_info

[Juha Keski-Saari]

Regrettably it seems I slipped a mistake into this patch which took out
the regulators VAUX1-3. Below is a version which removes this issue

>From 9ddec9979471fa7ba77532fa50c88137051d2037 Mon Sep 17 00:00:00 2001
From: Juha Keski-Saari <ext-juha.1.keski-saari@nokia.com>
Date: Wed, 25 Nov 2009 10:58:46 +0200
Subject: [PATCHv3 1/3] twl4030-regulator: Add all TWL regulators to twreg_info

Define all twl4030 regulators in the twlreg_info table, along with
appropriate VSEL tables for adjustable regulators

Signed-off-by: Juha Keski-Saari <ext-juha.1.keski-saari@nokia.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
---
 drivers/regulator/twl4030-regulator.c |   27 +++++++++++++++++----------
 1 files changed, 17 insertions(+), 10 deletions(-)

diff --git a/drivers/regulator/twl4030-regulator.c b/drivers/regulator/twl4030-regulator.c
index 9365140..c50b8b7 100644
--- a/drivers/regulator/twl4030-regulator.c
+++ b/drivers/regulator/twl4030-regulator.c
@@ -260,7 +260,18 @@ static const u16 VSIM_VSEL_table[] = {
 static const u16 VDAC_VSEL_table[] = {
 	1200, 1300, 1800, 1800,
 };
-
+static const u16 VDD1_VSEL_table[] = {
+	800, 1450,
+};
+static const u16 VDD2_VSEL_table[] = {
+	800, 1450, 1500,
+};
+static const u16 VIO_VSEL_table[] = {
+	1800, 1850,
+};
+static const u16 VINTANA2_VSEL_table[] = {
+	2500, 2750,
+};
 
 static int twl4030ldo_list_voltage(struct regulator_dev *rdev, unsigned index)
 {
@@ -397,20 +408,16 @@ static struct twlreg_info twl4030_regs[] = {
 	TWL_ADJUSTABLE_LDO(VAUX4, 0x23, 4),
 	TWL_ADJUSTABLE_LDO(VMMC1, 0x27, 5),
 	TWL_ADJUSTABLE_LDO(VMMC2, 0x2b, 6),
-	/*
 	TWL_ADJUSTABLE_LDO(VPLL1, 0x2f, 7),
-	*/
 	TWL_ADJUSTABLE_LDO(VPLL2, 0x33, 8),
 	TWL_ADJUSTABLE_LDO(VSIM, 0x37, 9),
 	TWL_ADJUSTABLE_LDO(VDAC, 0x3b, 10),
-	/*
-	TWL_ADJUSTABLE_LDO(VINTANA1, 0x3f, 11),
+	TWL_FIXED_LDO(VINTANA1, 0x3f, 1500, 11),
 	TWL_ADJUSTABLE_LDO(VINTANA2, 0x43, 12),
-	TWL_ADJUSTABLE_LDO(VINTDIG, 0x47, 13),
-	TWL_SMPS(VIO, 0x4b, 14),
-	TWL_SMPS(VDD1, 0x55, 15),
-	TWL_SMPS(VDD2, 0x63, 16),
-	 */
+	TWL_FIXED_LDO(VINTDIG, 0x47, 1500, 13),
+	TWL_ADJUSTABLE_LDO(VIO, 0x4b, 14),
+	TWL_ADJUSTABLE_LDO(VDD1, 0x55, 15),
+	TWL_ADJUSTABLE_LDO(VDD2, 0x63, 16),
 	TWL_FIXED_LDO(VUSB1V5, 0x71, 1500, 17),
 	TWL_FIXED_LDO(VUSB1V8, 0x74, 1800, 18),
 	TWL_FIXED_LDO(VUSB3V1, 0x77, 3100, 19),
-- 
1.6.3.3

Re: [PATCHv2 1/3] twl4030-regulator: Add all TWL regulators to twreg_info

[Liam Girdwood]

On Wed, 2009-11-25 at 15:38 +0200, Juha Keski-Saari wrote:
> Regrettably it seems I slipped a mistake into this patch which took out
> the regulators VAUX1-3. Below is a version which removes this issue
> 

Ah, I've just applied and pushed this series. Can you redo against
voltage for-next ?

Thanks

Liam

Re: [PATCHv2 1/3] twl4030-regulator: Add all TWL regulators to twreg_info

[Juha Keski-Saari]

On Wed, 2009-11-25 at 14:49 +0100, ext Liam Girdwood wrote:
> On Wed, 2009-11-25 at 15:38 +0200, Juha Keski-Saari wrote:
> > Regrettably it seems I slipped a mistake into this patch which took out
> > the regulators VAUX1-3. Below is a version which removes this issue
> > 
> 
> Ah, I've just applied and pushed this series. Can you redo against
> voltage for-next ?
> 
> Thanks
> 
> Liam

Here are the additions done on recent voltage-2.6/for-next, my apologies
for the extra work

>From 03578bd4f927f7777557be6d473eb0011b80608a Mon Sep 17 00:00:00 2001
From: Juha Keski-Saari <ext-juha.1.keski-saari@nokia.com>
Date: Wed, 25 Nov 2009 16:18:35 +0200
Subject: [PATCH] twl4030-regulator: Fixes VAUX1-3 exclusion introduced
in 3277b9fce0fcaa68d5947429e062163852ebc6fb

Signed-off-by: Juha Keski-Saari <ext-juha.1.keski-saari@nokia.com>
---
 drivers/regulator/twl4030-regulator.c |    4 ++++
 1 files changed, 4 insertions(+), 0 deletions(-)

diff --git a/drivers/regulator/twl4030-regulator.c
b/drivers/regulator/twl4030-regulator.c
index 02100bc..477c965 100644
--- a/drivers/regulator/twl4030-regulator.c
+++ b/drivers/regulator/twl4030-regulator.c
@@ -401,6 +401,10 @@ static struct regulator_ops twl4030fixed_ops = {
  * software control over them after boot.
  */
 static struct twlreg_info twl4030_regs[] = {
+	TWL_ADJUSTABLE_LDO(VAUX1, 0x17, 1),
+	TWL_ADJUSTABLE_LDO(VAUX2_4030, 0x1b, 2),
+	TWL_ADJUSTABLE_LDO(VAUX2, 0x1b, 2),
+	TWL_ADJUSTABLE_LDO(VAUX3, 0x1f, 3),
 	TWL_ADJUSTABLE_LDO(VAUX4, 0x23, 4),
 	TWL_ADJUSTABLE_LDO(VMMC1, 0x27, 5),
 	TWL_ADJUSTABLE_LDO(VMMC2, 0x2b, 6),
-- 
1.6.3.3

Re: [PATCHv2 1/3] twl4030-regulator: Add all TWL regulators to twreg_info

[Mark Brown]

On Wed, Nov 25, 2009 at 04:22:43PM +0200, Juha Keski-Saari wrote:

> Signed-off-by: Juha Keski-Saari <ext-juha.1.keski-saari@nokia.com>

all these are Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Re: [PATCHv2 1/3] twl4030-regulator: Add all TWL regulators to twreg_info

[Liam Girdwood]

On Wed, 2009-11-25 at 16:22 +0200, Juha Keski-Saari wrote:
> On Wed, 2009-11-25 at 14:49 +0100, ext Liam Girdwood wrote:
> > On Wed, 2009-11-25 at 15:38 +0200, Juha Keski-Saari wrote:
> > > Regrettably it seems I slipped a mistake into this patch which took out
> > > the regulators VAUX1-3. Below is a version which removes this issue
> > > 
> > 
> > Ah, I've just applied and pushed this series. Can you redo against
> > voltage for-next ?
> > 
> > Thanks
> > 
> > Liam
> 
> Here are the additions done on recent voltage-2.6/for-next, my apologies
> for the extra work
> 
> >From 03578bd4f927f7777557be6d473eb0011b80608a Mon Sep 17 00:00:00 2001
> From: Juha Keski-Saari <ext-juha.1.keski-saari@nokia.com>
> Date: Wed, 25 Nov 2009 16:18:35 +0200
> Subject: [PATCH] twl4030-regulator: Fixes VAUX1-3 exclusion introduced
> in 3277b9fce0fcaa68d5947429e062163852ebc6fb
> 
> Signed-off-by: Juha Keski-Saari <ext-juha.1.keski-saari@nokia.com>
> ---
>  drivers/regulator/twl4030-regulator.c |    4 ++++
>  1 files changed, 4 insertions(+), 0 deletions(-)
> 

Applied.

Thanks

Liam