* [PATCH/RESEND v11 1/7] usb: Add usb_endpoint_descriptor to be part of the struct usb_ep
[not found] <1305805417-31750-1-git-send-email-tlinder@codeaurora.org>
@ 2011-05-19 11:43 ` Tatyana Brokhman
2011-05-19 11:43 ` [PATCH v11 2/7] usb: Configure endpoint according to gadget speed Tatyana Brokhman
` (5 subsequent siblings)
6 siblings, 0 replies; 13+ messages in thread
From: Tatyana Brokhman @ 2011-05-19 11:43 UTC (permalink / raw)
To: greg; +Cc: linux-usb, balbi, ablay, linux-arm-msm, Tatyana Brokhman,
open list
Change usb_ep_enable() prototype to use endpoint descriptor from usb_ep.
This optimization spares the FDs from saving the endpoint chosen
descriptor. This optimization is not full though. To fully exploit this
change one needs to update all the UDCs as well since in the current
implementation each of them saves the endpoint descriptor in it's
internal (and extended) endpoint structure.
Signed-off-by: Tatyana Brokhman <tlinder@codeaurora.org>
---
drivers/usb/gadget/dbgp.c | 8 +++++---
drivers/usb/gadget/f_acm.c | 9 ++++-----
drivers/usb/gadget/f_audio.c | 5 ++---
drivers/usb/gadget/f_ecm.c | 17 ++++++++---------
drivers/usb/gadget/f_eem.c | 10 +++++-----
drivers/usb/gadget/f_fs.c | 3 ++-
drivers/usb/gadget/f_hid.c | 5 ++---
drivers/usb/gadget/f_loopback.c | 14 ++++++--------
drivers/usb/gadget/f_mass_storage.c | 3 ++-
drivers/usb/gadget/f_ncm.c | 17 ++++++++---------
drivers/usb/gadget/f_obex.c | 6 +++---
drivers/usb/gadget/f_phonet.c | 9 ++++-----
drivers/usb/gadget/f_rndis.c | 15 +++++++--------
drivers/usb/gadget/f_serial.c | 4 ++--
drivers/usb/gadget/f_sourcesink.c | 10 ++++------
drivers/usb/gadget/f_subset.c | 8 ++++----
drivers/usb/gadget/f_uvc.c | 6 ++++--
drivers/usb/gadget/file_storage.c | 3 ++-
drivers/usb/gadget/gmidi.c | 6 ++++--
drivers/usb/gadget/inode.c | 6 ++++--
drivers/usb/gadget/printer.c | 26 ++++++++++++++------------
drivers/usb/gadget/u_ether.c | 12 ++++++------
drivers/usb/gadget/u_ether.h | 4 ----
drivers/usb/gadget/u_serial.c | 4 ++--
drivers/usb/gadget/u_serial.h | 2 --
include/linux/usb/gadget.h | 16 +++++++---------
26 files changed, 111 insertions(+), 117 deletions(-)
diff --git a/drivers/usb/gadget/dbgp.c b/drivers/usb/gadget/dbgp.c
index dbe92ee..052209e 100644
--- a/drivers/usb/gadget/dbgp.c
+++ b/drivers/usb/gadget/dbgp.c
@@ -173,7 +173,9 @@ fail_1:
static int __enable_ep(struct usb_ep *ep, struct usb_endpoint_descriptor *desc)
{
- int err = usb_ep_enable(ep, desc);
+ int err;
+ ep->desc = desc;
+ err = usb_ep_enable(ep);
ep->driver_data = dbgp.gadget;
return err;
}
@@ -268,8 +270,8 @@ static int __init dbgp_configure_endpoints(struct usb_gadget *gadget)
dbgp.serial->in = dbgp.i_ep;
dbgp.serial->out = dbgp.o_ep;
- dbgp.serial->in_desc = &i_desc;
- dbgp.serial->out_desc = &o_desc;
+ dbgp.serial->in->desc = &i_desc;
+ dbgp.serial->out->desc = &o_desc;
if (gserial_setup(gadget, 1) < 0) {
stp = 3;
diff --git a/drivers/usb/gadget/f_acm.c b/drivers/usb/gadget/f_acm.c
index bd6226c..d04b4a6 100644
--- a/drivers/usb/gadget/f_acm.c
+++ b/drivers/usb/gadget/f_acm.c
@@ -62,7 +62,6 @@ struct f_acm {
struct acm_ep_descs hs;
struct usb_ep *notify;
- struct usb_endpoint_descriptor *notify_desc;
struct usb_request *notify_req;
struct usb_cdc_line_coding port_line_coding; /* 8-N-1 etc */
@@ -405,11 +404,11 @@ static int acm_set_alt(struct usb_function *f, unsigned intf, unsigned alt)
usb_ep_disable(acm->notify);
} else {
VDBG(cdev, "init acm ctrl interface %d\n", intf);
- acm->notify_desc = ep_choose(cdev->gadget,
+ acm->notify->desc = ep_choose(cdev->gadget,
acm->hs.notify,
acm->fs.notify);
}
- usb_ep_enable(acm->notify, acm->notify_desc);
+ usb_ep_enable(acm->notify);
acm->notify->driver_data = acm;
} else if (intf == acm->data_id) {
@@ -418,9 +417,9 @@ static int acm_set_alt(struct usb_function *f, unsigned intf, unsigned alt)
gserial_disconnect(&acm->port);
} else {
DBG(cdev, "activate acm ttyGS%d\n", acm->port_num);
- acm->port.in_desc = ep_choose(cdev->gadget,
+ acm->port.in->desc = ep_choose(cdev->gadget,
acm->hs.in, acm->fs.in);
- acm->port.out_desc = ep_choose(cdev->gadget,
+ acm->port.out->desc = ep_choose(cdev->gadget,
acm->hs.out, acm->fs.out);
}
gserial_connect(&acm->port, acm->port_num);
diff --git a/drivers/usb/gadget/f_audio.c b/drivers/usb/gadget/f_audio.c
index 8ee330a..02a0270 100644
--- a/drivers/usb/gadget/f_audio.c
+++ b/drivers/usb/gadget/f_audio.c
@@ -279,7 +279,6 @@ struct f_audio {
/* endpoints handle full and/or high speeds */
struct usb_ep *out_ep;
- struct usb_endpoint_descriptor *out_desc;
spinlock_t lock;
struct f_audio_buf *copy_buf;
@@ -575,7 +574,7 @@ static int f_audio_set_alt(struct usb_function *f, unsigned intf, unsigned alt)
if (intf == 1) {
if (alt == 1) {
- usb_ep_enable(out_ep, audio->out_desc);
+ usb_ep_enable(out_ep);
out_ep->driver_data = audio;
audio->copy_buf = f_audio_buffer_alloc(audio_buf_size);
if (IS_ERR(audio->copy_buf))
@@ -677,6 +676,7 @@ f_audio_bind(struct usb_configuration *c, struct usb_function *f)
if (!ep)
goto fail;
audio->out_ep = ep;
+ audio->out_ep->desc = &as_out_ep_desc;
ep->driver_data = cdev; /* claim */
status = -ENOMEM;
@@ -776,7 +776,6 @@ int __init audio_bind_config(struct usb_configuration *c)
audio->card.func.set_alt = f_audio_set_alt;
audio->card.func.setup = f_audio_setup;
audio->card.func.disable = f_audio_disable;
- audio->out_desc = &as_out_ep_desc;
control_selector_init(audio);
diff --git a/drivers/usb/gadget/f_ecm.c b/drivers/usb/gadget/f_ecm.c
index 544257a..7c996f2 100644
--- a/drivers/usb/gadget/f_ecm.c
+++ b/drivers/usb/gadget/f_ecm.c
@@ -68,7 +68,6 @@ struct f_ecm {
struct ecm_ep_descs hs;
struct usb_ep *notify;
- struct usb_endpoint_descriptor *notify_desc;
struct usb_request *notify_req;
u8 notify_state;
bool is_open;
@@ -466,11 +465,11 @@ static int ecm_set_alt(struct usb_function *f, unsigned intf, unsigned alt)
usb_ep_disable(ecm->notify);
} else {
VDBG(cdev, "init ecm ctrl %d\n", intf);
- ecm->notify_desc = ep_choose(cdev->gadget,
+ ecm->notify->desc = ep_choose(cdev->gadget,
ecm->hs.notify,
ecm->fs.notify);
}
- usb_ep_enable(ecm->notify, ecm->notify_desc);
+ usb_ep_enable(ecm->notify);
ecm->notify->driver_data = ecm;
/* Data interface has two altsettings, 0 and 1 */
@@ -483,11 +482,11 @@ static int ecm_set_alt(struct usb_function *f, unsigned intf, unsigned alt)
gether_disconnect(&ecm->port);
}
- if (!ecm->port.in) {
+ if (!ecm->port.in_ep->desc) {
DBG(cdev, "init ecm\n");
- ecm->port.in = ep_choose(cdev->gadget,
+ ecm->port.in_ep->desc = ep_choose(cdev->gadget,
ecm->hs.in, ecm->fs.in);
- ecm->port.out = ep_choose(cdev->gadget,
+ ecm->port.out_ep->desc = ep_choose(cdev->gadget,
ecm->hs.out, ecm->fs.out);
}
@@ -549,7 +548,7 @@ static void ecm_disable(struct usb_function *f)
if (ecm->notify->driver_data) {
usb_ep_disable(ecm->notify);
ecm->notify->driver_data = NULL;
- ecm->notify_desc = NULL;
+ ecm->notify->desc = NULL;
}
}
@@ -723,9 +722,9 @@ fail:
/* we might as well release our claims on endpoints */
if (ecm->notify)
ecm->notify->driver_data = NULL;
- if (ecm->port.out)
+ if (ecm->port.out_ep->desc)
ecm->port.out_ep->driver_data = NULL;
- if (ecm->port.in)
+ if (ecm->port.in_ep->desc)
ecm->port.in_ep->driver_data = NULL;
ERROR(cdev, "%s: can't bind, err %d\n", f->name, status);
diff --git a/drivers/usb/gadget/f_eem.c b/drivers/usb/gadget/f_eem.c
index b3c3042..fea8e3b 100644
--- a/drivers/usb/gadget/f_eem.c
+++ b/drivers/usb/gadget/f_eem.c
@@ -176,11 +176,11 @@ static int eem_set_alt(struct usb_function *f, unsigned intf, unsigned alt)
gether_disconnect(&eem->port);
}
- if (!eem->port.in) {
+ if (!eem->port.in_ep->desc) {
DBG(cdev, "init eem\n");
- eem->port.in = ep_choose(cdev->gadget,
+ eem->port.in_ep->desc = ep_choose(cdev->gadget,
eem->hs.in, eem->fs.in);
- eem->port.out = ep_choose(cdev->gadget,
+ eem->port.out_ep->desc = ep_choose(cdev->gadget,
eem->hs.out, eem->fs.out);
}
@@ -289,9 +289,9 @@ fail:
usb_free_descriptors(f->descriptors);
/* we might as well release our claims on endpoints */
- if (eem->port.out)
+ if (eem->port.out_ep->desc)
eem->port.out_ep->driver_data = NULL;
- if (eem->port.in)
+ if (eem->port.in_ep->desc)
eem->port.in_ep->driver_data = NULL;
ERROR(cdev, "%s: can't bind, err %d\n", f->name, status);
diff --git a/drivers/usb/gadget/f_fs.c b/drivers/usb/gadget/f_fs.c
index 19fffcc..c161a9a 100644
--- a/drivers/usb/gadget/f_fs.c
+++ b/drivers/usb/gadget/f_fs.c
@@ -1544,7 +1544,8 @@ static int ffs_func_eps_enable(struct ffs_function *func)
ds = ep->descs[ep->descs[1] ? 1 : 0];
ep->ep->driver_data = ep;
- ret = usb_ep_enable(ep->ep, ds);
+ ep->ep->desc = ds;
+ ret = usb_ep_enable(ep->ep);
if (likely(!ret)) {
epfile->ep = ep;
epfile->in = usb_endpoint_dir_in(ds);
diff --git a/drivers/usb/gadget/f_hid.c b/drivers/usb/gadget/f_hid.c
index 598e7e2..12879b6 100644
--- a/drivers/usb/gadget/f_hid.c
+++ b/drivers/usb/gadget/f_hid.c
@@ -416,7 +416,6 @@ static int hidg_set_alt(struct usb_function *f, unsigned intf, unsigned alt)
{
struct usb_composite_dev *cdev = f->config->cdev;
struct f_hidg *hidg = func_to_hidg(f);
- const struct usb_endpoint_descriptor *ep_desc;
int status = 0;
VDBG(cdev, "hidg_set_alt intf:%d alt:%d\n", intf, alt);
@@ -426,9 +425,9 @@ static int hidg_set_alt(struct usb_function *f, unsigned intf, unsigned alt)
if (hidg->in_ep->driver_data != NULL)
usb_ep_disable(hidg->in_ep);
- ep_desc = ep_choose(f->config->cdev->gadget,
+ hidg->in_ep->desc = ep_choose(f->config->cdev->gadget,
hidg->hs_in_ep_desc, hidg->fs_in_ep_desc);
- status = usb_ep_enable(hidg->in_ep, ep_desc);
+ status = usb_ep_enable(hidg->in_ep);
if (status < 0) {
ERROR(cdev, "Enable endpoint FAILED!\n");
goto fail;
diff --git a/drivers/usb/gadget/f_loopback.c b/drivers/usb/gadget/f_loopback.c
index b37960f..34e3cca 100644
--- a/drivers/usb/gadget/f_loopback.c
+++ b/drivers/usb/gadget/f_loopback.c
@@ -250,26 +250,24 @@ static int
enable_loopback(struct usb_composite_dev *cdev, struct f_loopback *loop)
{
int result = 0;
- const struct usb_endpoint_descriptor *src, *sink;
struct usb_ep *ep;
struct usb_request *req;
unsigned i;
- src = ep_choose(cdev->gadget,
- &hs_loop_source_desc, &fs_loop_source_desc);
- sink = ep_choose(cdev->gadget,
- &hs_loop_sink_desc, &fs_loop_sink_desc);
-
/* one endpoint writes data back IN to the host */
ep = loop->in_ep;
- result = usb_ep_enable(ep, src);
+ ep->desc = ep_choose(cdev->gadget,
+ &hs_loop_source_desc, &fs_loop_source_desc);
+ result = usb_ep_enable(ep);
if (result < 0)
return result;
ep->driver_data = loop;
/* one endpoint just reads OUT packets */
ep = loop->out_ep;
- result = usb_ep_enable(ep, sink);
+ ep->desc = ep_choose(cdev->gadget,
+ &hs_loop_sink_desc, &fs_loop_sink_desc);
+ result = usb_ep_enable(ep);
if (result < 0) {
fail0:
ep = loop->in_ep;
diff --git a/drivers/usb/gadget/f_mass_storage.c b/drivers/usb/gadget/f_mass_storage.c
index efb58f9..4eee434 100644
--- a/drivers/usb/gadget/f_mass_storage.c
+++ b/drivers/usb/gadget/f_mass_storage.c
@@ -2330,7 +2330,8 @@ static int enable_endpoint(struct fsg_common *common, struct usb_ep *ep,
int rc;
ep->driver_data = common;
- rc = usb_ep_enable(ep, d);
+ ep->desc = (struct usb_endpoint_descriptor *)d;
+ rc = usb_ep_enable(ep);
if (rc)
ERROR(common, "can't enable %s, result %d\n", ep->name, rc);
return rc;
diff --git a/drivers/usb/gadget/f_ncm.c b/drivers/usb/gadget/f_ncm.c
index 86902a6..06daa1b 100644
--- a/drivers/usb/gadget/f_ncm.c
+++ b/drivers/usb/gadget/f_ncm.c
@@ -70,7 +70,6 @@ struct f_ncm {
struct ncm_ep_descs hs;
struct usb_ep *notify;
- struct usb_endpoint_descriptor *notify_desc;
struct usb_request *notify_req;
u8 notify_state;
bool is_open;
@@ -804,11 +803,11 @@ static int ncm_set_alt(struct usb_function *f, unsigned intf, unsigned alt)
usb_ep_disable(ncm->notify);
} else {
DBG(cdev, "init ncm ctrl %d\n", intf);
- ncm->notify_desc = ep_choose(cdev->gadget,
+ ncm->notify->desc = ep_choose(cdev->gadget,
ncm->hs.notify,
ncm->fs.notify);
}
- usb_ep_enable(ncm->notify, ncm->notify_desc);
+ usb_ep_enable(ncm->notify);
ncm->notify->driver_data = ncm;
/* Data interface has two altsettings, 0 and 1 */
@@ -829,12 +828,12 @@ static int ncm_set_alt(struct usb_function *f, unsigned intf, unsigned alt)
if (alt == 1) {
struct net_device *net;
- if (!ncm->port.in) {
+ if (!ncm->port.in_ep->desc) {
DBG(cdev, "init ncm\n");
- ncm->port.in = ep_choose(cdev->gadget,
+ ncm->port.in_ep->desc = ep_choose(cdev->gadget,
ncm->hs.in,
ncm->fs.in);
- ncm->port.out = ep_choose(cdev->gadget,
+ ncm->port.out_ep->desc = ep_choose(cdev->gadget,
ncm->hs.out,
ncm->fs.out);
}
@@ -1111,7 +1110,7 @@ static void ncm_disable(struct usb_function *f)
if (ncm->notify->driver_data) {
usb_ep_disable(ncm->notify);
ncm->notify->driver_data = NULL;
- ncm->notify_desc = NULL;
+ ncm->notify->desc = NULL;
}
}
@@ -1288,9 +1287,9 @@ fail:
/* we might as well release our claims on endpoints */
if (ncm->notify)
ncm->notify->driver_data = NULL;
- if (ncm->port.out)
+ if (ncm->port.out_ep->desc)
ncm->port.out_ep->driver_data = NULL;
- if (ncm->port.in)
+ if (ncm->port.in_ep->desc)
ncm->port.in_ep->driver_data = NULL;
ERROR(cdev, "%s: can't bind, err %d\n", f->name, status);
diff --git a/drivers/usb/gadget/f_obex.c b/drivers/usb/gadget/f_obex.c
index 8f8c643..a6dbda09 100644
--- a/drivers/usb/gadget/f_obex.c
+++ b/drivers/usb/gadget/f_obex.c
@@ -227,11 +227,11 @@ static int obex_set_alt(struct usb_function *f, unsigned intf, unsigned alt)
gserial_disconnect(&obex->port);
}
- if (!obex->port.in_desc) {
+ if (!obex->port.in->desc) {
DBG(cdev, "init obex ttyGS%d\n", obex->port_num);
- obex->port.in_desc = ep_choose(cdev->gadget,
+ obex->port.in->desc = ep_choose(cdev->gadget,
obex->hs.obex_in, obex->fs.obex_in);
- obex->port.out_desc = ep_choose(cdev->gadget,
+ obex->port.out->desc = ep_choose(cdev->gadget,
obex->hs.obex_out, obex->fs.obex_out);
}
diff --git a/drivers/usb/gadget/f_phonet.c b/drivers/usb/gadget/f_phonet.c
index 5e14950..dc63f16 100644
--- a/drivers/usb/gadget/f_phonet.c
+++ b/drivers/usb/gadget/f_phonet.c
@@ -427,17 +427,16 @@ static int pn_set_alt(struct usb_function *f, unsigned intf, unsigned alt)
spin_lock(&port->lock);
__pn_reset(f);
if (alt == 1) {
- struct usb_endpoint_descriptor *out, *in;
int i;
- out = ep_choose(gadget,
+ fp->out_ep->desc = ep_choose(gadget,
&pn_hs_sink_desc,
&pn_fs_sink_desc);
- in = ep_choose(gadget,
+ fp->in_ep->desc = ep_choose(gadget,
&pn_hs_source_desc,
&pn_fs_source_desc);
- usb_ep_enable(fp->out_ep, out);
- usb_ep_enable(fp->in_ep, in);
+ usb_ep_enable(fp->out_ep);
+ usb_ep_enable(fp->in_ep);
port->usb = fp;
fp->out_ep->driver_data = fp;
diff --git a/drivers/usb/gadget/f_rndis.c b/drivers/usb/gadget/f_rndis.c
index fa12ec8..4646254 100644
--- a/drivers/usb/gadget/f_rndis.c
+++ b/drivers/usb/gadget/f_rndis.c
@@ -92,7 +92,6 @@ struct f_rndis {
struct rndis_ep_descs hs;
struct usb_ep *notify;
- struct usb_endpoint_descriptor *notify_desc;
struct usb_request *notify_req;
atomic_t notify_count;
};
@@ -486,11 +485,11 @@ static int rndis_set_alt(struct usb_function *f, unsigned intf, unsigned alt)
usb_ep_disable(rndis->notify);
} else {
VDBG(cdev, "init rndis ctrl %d\n", intf);
- rndis->notify_desc = ep_choose(cdev->gadget,
+ rndis->notify->desc = ep_choose(cdev->gadget,
rndis->hs.notify,
rndis->fs.notify);
}
- usb_ep_enable(rndis->notify, rndis->notify_desc);
+ usb_ep_enable(rndis->notify);
rndis->notify->driver_data = rndis;
} else if (intf == rndis->data_id) {
@@ -501,11 +500,11 @@ static int rndis_set_alt(struct usb_function *f, unsigned intf, unsigned alt)
gether_disconnect(&rndis->port);
}
- if (!rndis->port.in) {
+ if (!rndis->port.in_ep->desc) {
DBG(cdev, "init rndis\n");
- rndis->port.in = ep_choose(cdev->gadget,
+ rndis->port.in_ep->desc = ep_choose(cdev->gadget,
rndis->hs.in, rndis->fs.in);
- rndis->port.out = ep_choose(cdev->gadget,
+ rndis->port.out_ep->desc = ep_choose(cdev->gadget,
rndis->hs.out, rndis->fs.out);
}
@@ -738,9 +737,9 @@ fail:
/* we might as well release our claims on endpoints */
if (rndis->notify)
rndis->notify->driver_data = NULL;
- if (rndis->port.out)
+ if (rndis->port.out_ep->desc)
rndis->port.out_ep->driver_data = NULL;
- if (rndis->port.in)
+ if (rndis->port.in_ep->desc)
rndis->port.in_ep->driver_data = NULL;
ERROR(cdev, "%s: can't bind, err %d\n", f->name, status);
diff --git a/drivers/usb/gadget/f_serial.c b/drivers/usb/gadget/f_serial.c
index 490b00b..a9ce626 100644
--- a/drivers/usb/gadget/f_serial.c
+++ b/drivers/usb/gadget/f_serial.c
@@ -138,9 +138,9 @@ static int gser_set_alt(struct usb_function *f, unsigned intf, unsigned alt)
gserial_disconnect(&gser->port);
} else {
DBG(cdev, "activate generic ttyGS%d\n", gser->port_num);
- gser->port.in_desc = ep_choose(cdev->gadget,
+ gser->port.in->desc = ep_choose(cdev->gadget,
gser->hs.in, gser->fs.in);
- gser->port.out_desc = ep_choose(cdev->gadget,
+ gser->port.out->desc = ep_choose(cdev->gadget,
gser->hs.out, gser->fs.out);
}
gserial_connect(&gser->port, gser->port_num);
diff --git a/drivers/usb/gadget/f_sourcesink.c b/drivers/usb/gadget/f_sourcesink.c
index e403a53..0ffddd3 100644
--- a/drivers/usb/gadget/f_sourcesink.c
+++ b/drivers/usb/gadget/f_sourcesink.c
@@ -343,15 +343,12 @@ static int
enable_source_sink(struct usb_composite_dev *cdev, struct f_sourcesink *ss)
{
int result = 0;
- const struct usb_endpoint_descriptor *src, *sink;
struct usb_ep *ep;
- src = ep_choose(cdev->gadget, &hs_source_desc, &fs_source_desc);
- sink = ep_choose(cdev->gadget, &hs_sink_desc, &fs_sink_desc);
-
/* one endpoint writes (sources) zeroes IN (to the host) */
ep = ss->in_ep;
- result = usb_ep_enable(ep, src);
+ ep->desc = ep_choose(cdev->gadget, &hs_source_desc, &fs_source_desc);
+ result = usb_ep_enable(ep);
if (result < 0)
return result;
ep->driver_data = ss;
@@ -367,7 +364,8 @@ fail:
/* one endpoint reads (sinks) anything OUT (from the host) */
ep = ss->out_ep;
- result = usb_ep_enable(ep, sink);
+ ep->desc = ep_choose(cdev->gadget, &hs_sink_desc, &fs_sink_desc);
+ result = usb_ep_enable(ep);
if (result < 0)
goto fail;
ep->driver_data = ss;
diff --git a/drivers/usb/gadget/f_subset.c b/drivers/usb/gadget/f_subset.c
index 8675ca4..aecaed1 100644
--- a/drivers/usb/gadget/f_subset.c
+++ b/drivers/usb/gadget/f_subset.c
@@ -243,9 +243,9 @@ static int geth_set_alt(struct usb_function *f, unsigned intf, unsigned alt)
}
DBG(cdev, "init + activate cdc subset\n");
- geth->port.in = ep_choose(cdev->gadget,
+ geth->port.in_ep->desc = ep_choose(cdev->gadget,
geth->hs.in, geth->fs.in);
- geth->port.out = ep_choose(cdev->gadget,
+ geth->port.out_ep->desc = ep_choose(cdev->gadget,
geth->hs.out, geth->fs.out);
net = gether_connect(&geth->port);
@@ -334,9 +334,9 @@ geth_bind(struct usb_configuration *c, struct usb_function *f)
fail:
/* we might as well release our claims on endpoints */
- if (geth->port.out)
+ if (geth->port.out_ep->desc)
geth->port.out_ep->driver_data = NULL;
- if (geth->port.in)
+ if (geth->port.in_ep->desc)
geth->port.in_ep->driver_data = NULL;
ERROR(cdev, "%s: can't bind, err %d\n", f->name, status);
diff --git a/drivers/usb/gadget/f_uvc.c b/drivers/usb/gadget/f_uvc.c
index be446b7..df74d03 100644
--- a/drivers/usb/gadget/f_uvc.c
+++ b/drivers/usb/gadget/f_uvc.c
@@ -262,8 +262,10 @@ uvc_function_set_alt(struct usb_function *f, unsigned interface, unsigned alt)
if (uvc->state != UVC_STATE_CONNECTED)
return 0;
- if (uvc->video.ep)
- usb_ep_enable(uvc->video.ep, &uvc_streaming_ep);
+ if (uvc->video.ep) {
+ uvc->video.ep->desc = &uvc_streaming_ep;
+ usb_ep_enable(uvc->video.ep);
+ }
memset(&v4l2_event, 0, sizeof(v4l2_event));
v4l2_event.type = UVC_EVENT_STREAMON;
diff --git a/drivers/usb/gadget/file_storage.c b/drivers/usb/gadget/file_storage.c
index 0360f56..0d55dee 100644
--- a/drivers/usb/gadget/file_storage.c
+++ b/drivers/usb/gadget/file_storage.c
@@ -2713,7 +2713,8 @@ static int enable_endpoint(struct fsg_dev *fsg, struct usb_ep *ep,
int rc;
ep->driver_data = fsg;
- rc = usb_ep_enable(ep, d);
+ ep->desc = d;
+ rc = usb_ep_enable(ep);
if (rc)
ERROR(fsg, "can't enable %s, result %d\n", ep->name, rc);
return rc;
diff --git a/drivers/usb/gadget/gmidi.c b/drivers/usb/gadget/gmidi.c
index 47b86b9..4f40f14 100644
--- a/drivers/usb/gadget/gmidi.c
+++ b/drivers/usb/gadget/gmidi.c
@@ -537,14 +537,16 @@ static int set_gmidi_config(struct gmidi_device *dev, gfp_t gfp_flags)
struct usb_ep *ep;
unsigned i;
- err = usb_ep_enable(dev->in_ep, &bulk_in_desc);
+ dev->in_ep->desc = &bulk_in_desc;
+ err = usb_ep_enable(dev->in_ep);
if (err) {
ERROR(dev, "can't start %s: %d\n", dev->in_ep->name, err);
goto fail;
}
dev->in_ep->driver_data = dev;
- err = usb_ep_enable(dev->out_ep, &bulk_out_desc);
+ dev->out_ep->desc = &bulk_out_desc;
+ err = usb_ep_enable(dev->out_ep);
if (err) {
ERROR(dev, "can't start %s: %d\n", dev->out_ep->name, err);
goto fail;
diff --git a/drivers/usb/gadget/inode.c b/drivers/usb/gadget/inode.c
index a01383f..4674b44 100644
--- a/drivers/usb/gadget/inode.c
+++ b/drivers/usb/gadget/inode.c
@@ -830,14 +830,16 @@ ep_config (struct file *fd, const char __user *buf, size_t len, loff_t *ptr)
switch (data->dev->gadget->speed) {
case USB_SPEED_LOW:
case USB_SPEED_FULL:
- value = usb_ep_enable (ep, &data->desc);
+ ep->desc = &data->desc;
+ value = usb_ep_enable(ep);
if (value == 0)
data->state = STATE_EP_ENABLED;
break;
#ifdef CONFIG_USB_GADGET_DUALSPEED
case USB_SPEED_HIGH:
/* fails if caller didn't provide that descriptor... */
- value = usb_ep_enable (ep, &data->hs_desc);
+ ep->desc = &data->hs_desc;
+ value = usb_ep_enable(ep);
if (value == 0)
data->state = STATE_EP_ENABLED;
break;
diff --git a/drivers/usb/gadget/printer.c b/drivers/usb/gadget/printer.c
index 271ef94..00e5f19 100644
--- a/drivers/usb/gadget/printer.c
+++ b/drivers/usb/gadget/printer.c
@@ -89,8 +89,7 @@ struct printer_dev {
u8 config;
s8 interface;
struct usb_ep *in_ep, *out_ep;
- const struct usb_endpoint_descriptor
- *in, *out;
+
struct list_head rx_reqs; /* List of free RX structs */
struct list_head rx_reqs_active; /* List of Active RX xfers */
struct list_head rx_buffers; /* List of completed xfers */
@@ -895,19 +894,20 @@ set_printer_interface(struct printer_dev *dev)
{
int result = 0;
- dev->in = ep_desc(dev->gadget, &hs_ep_in_desc, &fs_ep_in_desc);
+ dev->in_ep->desc = ep_desc(dev->gadget, &hs_ep_in_desc, &fs_ep_in_desc);
dev->in_ep->driver_data = dev;
- dev->out = ep_desc(dev->gadget, &hs_ep_out_desc, &fs_ep_out_desc);
+ dev->out_ep->desc = ep_desc(dev->gadget, &hs_ep_out_desc,
+ &fs_ep_out_desc);
dev->out_ep->driver_data = dev;
- result = usb_ep_enable(dev->in_ep, dev->in);
+ result = usb_ep_enable(dev->in_ep);
if (result != 0) {
DBG(dev, "enable %s --> %d\n", dev->in_ep->name, result);
goto done;
}
- result = usb_ep_enable(dev->out_ep, dev->out);
+ result = usb_ep_enable(dev->out_ep);
if (result != 0) {
DBG(dev, "enable %s --> %d\n", dev->in_ep->name, result);
goto done;
@@ -918,8 +918,8 @@ done:
if (result != 0) {
(void) usb_ep_disable(dev->in_ep);
(void) usb_ep_disable(dev->out_ep);
- dev->in = NULL;
- dev->out = NULL;
+ dev->in_ep->desc = NULL;
+ dev->out_ep->desc = NULL;
}
/* caller is responsible for cleanup on error */
@@ -933,12 +933,14 @@ static void printer_reset_interface(struct printer_dev *dev)
DBG(dev, "%s\n", __func__);
- if (dev->in)
+ if (dev->in_ep->desc)
usb_ep_disable(dev->in_ep);
- if (dev->out)
+ if (dev->out_ep->desc)
usb_ep_disable(dev->out_ep);
+ dev->in_ep->desc = NULL;
+ dev->out_ep->desc = NULL;
dev->interface = -1;
}
@@ -1104,9 +1106,9 @@ static void printer_soft_reset(struct printer_dev *dev)
list_add(&req->list, &dev->tx_reqs);
}
- if (usb_ep_enable(dev->in_ep, dev->in))
+ if (usb_ep_enable(dev->in_ep))
DBG(dev, "Failed to enable USB in_ep\n");
- if (usb_ep_enable(dev->out_ep, dev->out))
+ if (usb_ep_enable(dev->out_ep))
DBG(dev, "Failed to enable USB out_ep\n");
wake_up_interruptible(&dev->rx_wait);
diff --git a/drivers/usb/gadget/u_ether.c b/drivers/usb/gadget/u_ether.c
index 2ac1d21..b91363e 100644
--- a/drivers/usb/gadget/u_ether.c
+++ b/drivers/usb/gadget/u_ether.c
@@ -693,8 +693,8 @@ static int eth_stop(struct net_device *net)
usb_ep_disable(link->out_ep);
if (netif_carrier_ok(net)) {
DBG(dev, "host still using in/out endpoints\n");
- usb_ep_enable(link->in_ep, link->in);
- usb_ep_enable(link->out_ep, link->out);
+ usb_ep_enable(link->in_ep);
+ usb_ep_enable(link->out_ep);
}
}
spin_unlock_irqrestore(&dev->lock, flags);
@@ -871,7 +871,7 @@ struct net_device *gether_connect(struct gether *link)
return ERR_PTR(-EINVAL);
link->in_ep->driver_data = dev;
- result = usb_ep_enable(link->in_ep, link->in);
+ result = usb_ep_enable(link->in_ep);
if (result != 0) {
DBG(dev, "enable %s --> %d\n",
link->in_ep->name, result);
@@ -879,7 +879,7 @@ struct net_device *gether_connect(struct gether *link)
}
link->out_ep->driver_data = dev;
- result = usb_ep_enable(link->out_ep, link->out);
+ result = usb_ep_enable(link->out_ep);
if (result != 0) {
DBG(dev, "enable %s --> %d\n",
link->out_ep->name, result);
@@ -969,7 +969,7 @@ void gether_disconnect(struct gether *link)
}
spin_unlock(&dev->req_lock);
link->in_ep->driver_data = NULL;
- link->in = NULL;
+ link->in_ep->desc = NULL;
usb_ep_disable(link->out_ep);
spin_lock(&dev->req_lock);
@@ -984,7 +984,7 @@ void gether_disconnect(struct gether *link)
}
spin_unlock(&dev->req_lock);
link->out_ep->driver_data = NULL;
- link->out = NULL;
+ link->out_ep->desc = NULL;
/* finish forgetting about this USB link episode */
dev->header_len = 0;
diff --git a/drivers/usb/gadget/u_ether.h b/drivers/usb/gadget/u_ether.h
index b56e1e7..c966440 100644
--- a/drivers/usb/gadget/u_ether.h
+++ b/drivers/usb/gadget/u_ether.h
@@ -52,10 +52,6 @@ struct gether {
struct usb_ep *in_ep;
struct usb_ep *out_ep;
- /* descriptors match device speed at gether_connect() time */
- struct usb_endpoint_descriptor *in;
- struct usb_endpoint_descriptor *out;
-
bool is_zlp_ok;
u16 cdc_filter;
diff --git a/drivers/usb/gadget/u_serial.c b/drivers/usb/gadget/u_serial.c
index 40f7716..a8aa469 100644
--- a/drivers/usb/gadget/u_serial.c
+++ b/drivers/usb/gadget/u_serial.c
@@ -1247,12 +1247,12 @@ int gserial_connect(struct gserial *gser, u8 port_num)
port = ports[port_num].port;
/* activate the endpoints */
- status = usb_ep_enable(gser->in, gser->in_desc);
+ status = usb_ep_enable(gser->in);
if (status < 0)
return status;
gser->in->driver_data = port;
- status = usb_ep_enable(gser->out, gser->out_desc);
+ status = usb_ep_enable(gser->out);
if (status < 0)
goto fail_out;
gser->out->driver_data = port;
diff --git a/drivers/usb/gadget/u_serial.h b/drivers/usb/gadget/u_serial.h
index 300f0ed..9b0fe64 100644
--- a/drivers/usb/gadget/u_serial.h
+++ b/drivers/usb/gadget/u_serial.h
@@ -35,8 +35,6 @@ struct gserial {
struct usb_ep *in;
struct usb_ep *out;
- struct usb_endpoint_descriptor *in_desc;
- struct usb_endpoint_descriptor *out_desc;
/* REVISIT avoid this CDC-ACM support harder ... */
struct usb_cdc_line_coding port_line_coding; /* 9600-8-N-1 etc */
diff --git a/include/linux/usb/gadget.h b/include/linux/usb/gadget.h
index dd1571d..5c4c30c 100644
--- a/include/linux/usb/gadget.h
+++ b/include/linux/usb/gadget.h
@@ -131,8 +131,9 @@ struct usb_ep_ops {
* @maxpacket:The maximum packet size used on this endpoint. The initial
* value can sometimes be reduced (hardware allowing), according to
* the endpoint descriptor used to configure the endpoint.
- * @driver_data:for use by the gadget driver. all other fields are
- * read-only to gadget drivers.
+ * @driver_data:for use by the gadget driver.
+ * @desc: endpoint descriptor. This pointer is set before the endpoint is
+ * enabled and remains valid until the endpoint is disabled.
*
* the bus controller driver lists all the general purpose endpoints in
* gadget->ep_list. the control endpoint (gadget->ep0) is not in that list,
@@ -145,6 +146,7 @@ struct usb_ep {
const struct usb_ep_ops *ops;
struct list_head ep_list;
unsigned maxpacket:16;
+ const struct usb_endpoint_descriptor *desc;
};
/*-------------------------------------------------------------------------*/
@@ -153,11 +155,8 @@ struct usb_ep {
* usb_ep_enable - configure endpoint, making it usable
* @ep:the endpoint being configured. may not be the endpoint named "ep0".
* drivers discover endpoints through the ep_list of a usb_gadget.
- * @desc:descriptor for desired behavior. caller guarantees this pointer
- * remains valid until the endpoint is disabled; the data byte order
- * is little-endian (usb-standard).
*
- * when configurations are set, or when interface settings change, the driver
+ * When configurations are set, or when interface settings change, the driver
* will enable or disable the relevant endpoints. while it is enabled, an
* endpoint may be used for i/o until the driver receives a disconnect() from
* the host or until the endpoint is disabled.
@@ -172,10 +171,9 @@ struct usb_ep {
*
* returns zero, or a negative error code.
*/
-static inline int usb_ep_enable(struct usb_ep *ep,
- const struct usb_endpoint_descriptor *desc)
+static inline int usb_ep_enable(struct usb_ep *ep)
{
- return ep->ops->enable(ep, desc);
+ return ep->ops->enable(ep, ep->desc);
}
/**
--
1.7.3.3
--
Sent by an employee of the Qualcomm Innovation Center, Inc.
The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum.
^ permalink raw reply related [flat|nested] 13+ messages in thread* [PATCH v11 2/7] usb: Configure endpoint according to gadget speed.
[not found] <1305805417-31750-1-git-send-email-tlinder@codeaurora.org>
2011-05-19 11:43 ` [PATCH/RESEND v11 1/7] usb: Add usb_endpoint_descriptor to be part of the struct usb_ep Tatyana Brokhman
@ 2011-05-19 11:43 ` Tatyana Brokhman
2011-05-20 15:24 ` Sebastian Andrzej Siewior
2011-05-19 11:43 ` [PATCH/RESEND v11 3/7] usb: Modify existing gadget drivers to use config_ep_by_speed() instead of ep_choose Tatyana Brokhman
` (4 subsequent siblings)
6 siblings, 1 reply; 13+ messages in thread
From: Tatyana Brokhman @ 2011-05-19 11:43 UTC (permalink / raw)
To: greg; +Cc: linux-usb, balbi, ablay, linux-arm-msm, Tatyana Brokhman,
open list
Add config_ep_by_speed() to configure the endpoint according to the gadget
speed. Using this function will spare the FDs from handling the endpoint
chosen descriptor.
Signed-off-by: Tatyana Brokhman <tlinder@codeaurora.org>
---
drivers/usb/gadget/composite.c | 86 +++++++++++++++++++++++++++++++++++++++
drivers/usb/gadget/epautoconf.c | 1 +
include/linux/usb/composite.h | 21 +++++++++
include/linux/usb/gadget.h | 3 +
4 files changed, 111 insertions(+), 0 deletions(-)
diff --git a/drivers/usb/gadget/composite.c b/drivers/usb/gadget/composite.c
index 5cbb1a4..cfba1ee 100644
--- a/drivers/usb/gadget/composite.c
+++ b/drivers/usb/gadget/composite.c
@@ -27,6 +27,7 @@
#include <linux/utsname.h>
#include <linux/usb/composite.h>
+#include <linux/byteorder/generic.h>
/*
@@ -74,6 +75,91 @@ MODULE_PARM_DESC(iSerialNumber, "SerialNumber string");
static char composite_manufacturer[50];
/*-------------------------------------------------------------------------*/
+/**
+ * next_ep_desc() - advance to the next EP descriptor
+ * @t: currect pointer within descriptor array
+ *
+ * Return: next EP descriptor or NULL
+ *
+ * Iterate over @t until either EP descriptor found or
+ * NULL (that indicates end of list) encountered
+ */
+static struct usb_descriptor_header**
+next_ep_desc(struct usb_descriptor_header **t)
+{
+ for (; *t; t++) {
+ if ((*t)->bDescriptorType == USB_DT_ENDPOINT)
+ return t;
+ }
+ return NULL;
+}
+
+/*
+ * for_each_ep_desc()- iterate over endpoint descriptors in the
+ * descriptors list
+ * @start: pointer within descriptor array.
+ * @ep_desc: endpoint descriptor to use as the loop cursor
+ */
+#define for_each_ep_desc(start, ep_desc) \
+ for (ep_desc = next_ep_desc(start); \
+ ep_desc; ep_desc = next_ep_desc(ep_desc+1))
+
+/**
+ * config_ep_by_speed() - configures the given endpoint
+ * according to gadget speed.
+ * @g: pointer to the gadget
+ * @f: usb function
+ * @_ep: the endpoint to configure
+ *
+ * Return: error code, 0 on success
+ *
+ * This function chooses the right descriptors for a given
+ * endpoint according to gadget speed and saves it in the
+ * endpoint desc field. If the endpoint already has a descriptor
+ * assigned to it - overwrites it with currently corresponding
+ * descriptor. The endpoint maxpacket field is updated according
+ * to the chosen descriptor.
+ * Note: the supplied function should hold all the descriptors
+ * for supported speeds
+ */
+int config_ep_by_speed(struct usb_gadget *g,
+ struct usb_function *f,
+ struct usb_ep *_ep)
+{
+ struct usb_endpoint_descriptor *chosen_desc = NULL;
+ struct usb_descriptor_header **speed_desc = NULL;
+
+ struct usb_descriptor_header **d_spd; /* cursor for speed desc */
+
+ if (!g || !f || !_ep)
+ return -EIO;
+
+ /* select desired speed */
+ switch (g->speed) {
+ case USB_SPEED_HIGH:
+ if (gadget_is_dualspeed(g)) {
+ speed_desc = f->hs_descriptors;
+ break;
+ }
+ /* else: fall through */
+ default:
+ speed_desc = f->descriptors;
+ }
+ /* find descriptors */
+ for_each_ep_desc(speed_desc, d_spd) {
+ chosen_desc = (struct usb_endpoint_descriptor *)*d_spd;
+ if (chosen_desc->bEndpointAddress == _ep->address)
+ goto ep_found;
+ }
+ return -EIO;
+
+ep_found:
+ /* commit results */
+ _ep->maxpacket = le16_to_cpu(chosen_desc->wMaxPacketSize);
+ _ep->desc = chosen_desc;
+
+ return 0;
+}
/**
* usb_add_function() - add a function to a configuration
diff --git a/drivers/usb/gadget/epautoconf.c b/drivers/usb/gadget/epautoconf.c
index 9b7360f..0022d44 100644
--- a/drivers/usb/gadget/epautoconf.c
+++ b/drivers/usb/gadget/epautoconf.c
@@ -191,6 +191,7 @@ ep_matches (
size = 64;
desc->wMaxPacketSize = cpu_to_le16(size);
}
+ ep->address = desc->bEndpointAddress;
return 1;
}
diff --git a/include/linux/usb/composite.h b/include/linux/usb/composite.h
index b78cba4..324fbc7 100644
--- a/include/linux/usb/composite.h
+++ b/include/linux/usb/composite.h
@@ -146,6 +146,27 @@ int usb_function_activate(struct usb_function *);
int usb_interface_id(struct usb_configuration *, struct usb_function *);
/**
+ * config_ep_by_speed() - configures the given endpoint
+ * according to gadget speed.
+ * @g: pointer to the gadget
+ * @f: usb function
+ * @_ep: the endpoint to configure
+ *
+ * Return: error code, 0 on success
+ *
+ * This function chooses the right descriptors for a given
+ * endpoint according to gadget speed and saves it in the
+ * endpoint desc field. If the endpoint already has a descriptor
+ * assigned to it - overwrites it with currently corresponding
+ * descriptor. The endpoint maxpacket field is updated according
+ * to the chosen descriptor.
+ * Note: the supplied function should hold all the descriptors
+ * for supported speeds
+ */
+int config_ep_by_speed(struct usb_gadget *g, struct usb_function *f,
+ struct usb_ep *_ep);
+
+/**
* ep_choose - select descriptor endpoint at current device speed
* @g: gadget, connected and running at some speed
* @hs: descriptor to use for high speed operation
diff --git a/include/linux/usb/gadget.h b/include/linux/usb/gadget.h
index 5c4c30c..8015ceb 100644
--- a/include/linux/usb/gadget.h
+++ b/include/linux/usb/gadget.h
@@ -132,6 +132,8 @@ struct usb_ep_ops {
* value can sometimes be reduced (hardware allowing), according to
* the endpoint descriptor used to configure the endpoint.
* @driver_data:for use by the gadget driver.
+ * @address: used to identify the endpoint when finding descriptor that
+ * matches connection speed
* @desc: endpoint descriptor. This pointer is set before the endpoint is
* enabled and remains valid until the endpoint is disabled.
*
@@ -146,6 +148,7 @@ struct usb_ep {
const struct usb_ep_ops *ops;
struct list_head ep_list;
unsigned maxpacket:16;
+ u8 address;
const struct usb_endpoint_descriptor *desc;
};
--
1.7.3.3
--
Sent by an employee of the Qualcomm Innovation Center, Inc.
The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum.
^ permalink raw reply related [flat|nested] 13+ messages in thread* Re: [PATCH v11 2/7] usb: Configure endpoint according to gadget speed.
2011-05-19 11:43 ` [PATCH v11 2/7] usb: Configure endpoint according to gadget speed Tatyana Brokhman
@ 2011-05-20 15:24 ` Sebastian Andrzej Siewior
0 siblings, 0 replies; 13+ messages in thread
From: Sebastian Andrzej Siewior @ 2011-05-20 15:24 UTC (permalink / raw)
To: Tatyana Brokhman; +Cc: greg, linux-usb, balbi, ablay, linux-arm-msm, open list
* Tatyana Brokhman | 2011-05-19 14:43:27 [+0300]:
>diff --git a/drivers/usb/gadget/composite.c b/drivers/usb/gadget/composite.c
>index 5cbb1a4..cfba1ee 100644
>--- a/drivers/usb/gadget/composite.c
>+++ b/drivers/usb/gadget/composite.c
>@@ -27,6 +27,7 @@
> #include <linux/utsname.h>
>
> #include <linux/usb/composite.h>
>+#include <linux/byteorder/generic.h>
Just applied that patch on v39 + usb-next nad it builds without this
line. Why is it required?
>diff --git a/include/linux/usb/composite.h b/include/linux/usb/composite.h
>index b78cba4..324fbc7 100644
>--- a/include/linux/usb/composite.h
>+++ b/include/linux/usb/composite.h
>@@ -146,6 +146,27 @@ int usb_function_activate(struct usb_function *);
> int usb_interface_id(struct usb_configuration *, struct usb_function *);
>
> /**
>+ * config_ep_by_speed() - configures the given endpoint
>+ * according to gadget speed.
>+ * @g: pointer to the gadget
>+ * @f: usb function
>+ * @_ep: the endpoint to configure
>+ *
>+ * Return: error code, 0 on success
>+ *
>+ * This function chooses the right descriptors for a given
>+ * endpoint according to gadget speed and saves it in the
>+ * endpoint desc field. If the endpoint already has a descriptor
>+ * assigned to it - overwrites it with currently corresponding
>+ * descriptor. The endpoint maxpacket field is updated according
>+ * to the chosen descriptor.
>+ * Note: the supplied function should hold all the descriptors
>+ * for supported speeds
>+ */
Didn't we aggree on not adding the same kerneldoc to function's
prototype and the actual function? Please add it only to the function's
implemention.
>+int config_ep_by_speed(struct usb_gadget *g, struct usb_function *f,
>+ struct usb_ep *_ep);
>+
Sebastian
^ permalink raw reply [flat|nested] 13+ messages in thread
* [PATCH/RESEND v11 3/7] usb: Modify existing gadget drivers to use config_ep_by_speed() instead of ep_choose.
[not found] <1305805417-31750-1-git-send-email-tlinder@codeaurora.org>
2011-05-19 11:43 ` [PATCH/RESEND v11 1/7] usb: Add usb_endpoint_descriptor to be part of the struct usb_ep Tatyana Brokhman
2011-05-19 11:43 ` [PATCH v11 2/7] usb: Configure endpoint according to gadget speed Tatyana Brokhman
@ 2011-05-19 11:43 ` Tatyana Brokhman
2011-05-19 11:43 ` [PATCH v11 4/7] usb:gadget: Add SuperSpeed support to the Gadget Framework Tatyana Brokhman
` (3 subsequent siblings)
6 siblings, 0 replies; 13+ messages in thread
From: Tatyana Brokhman @ 2011-05-19 11:43 UTC (permalink / raw)
To: greg; +Cc: linux-usb, balbi, ablay, linux-arm-msm, Tatyana Brokhman,
open list
Remove obsolete functions:
1. ep_choose()
2. usb_find_endpoint()
Signed-off-by: Tatyana Brokhman <tlinder@codeaurora.org>
---
drivers/usb/gadget/config.c | 25 ------------------
drivers/usb/gadget/f_acm.c | 47 ++++++++++-----------------------
drivers/usb/gadget/f_ecm.c | 45 ++++++++++----------------------
drivers/usb/gadget/f_eem.c | 32 ++++++----------------
drivers/usb/gadget/f_hid.c | 19 ++++---------
drivers/usb/gadget/f_loopback.c | 11 +++++---
drivers/usb/gadget/f_mass_storage.c | 34 +++++++++---------------
drivers/usb/gadget/f_ncm.c | 49 ++++++++++------------------------
drivers/usb/gadget/f_obex.c | 32 ++++++----------------
drivers/usb/gadget/f_phonet.c | 12 ++++----
drivers/usb/gadget/f_rndis.c | 45 +++++++++----------------------
drivers/usb/gadget/f_serial.c | 32 +++++-----------------
drivers/usb/gadget/f_sourcesink.c | 8 ++++-
drivers/usb/gadget/f_subset.c | 29 ++++----------------
include/linux/usb/composite.h | 15 ----------
include/linux/usb/gadget.h | 6 ----
16 files changed, 126 insertions(+), 315 deletions(-)
diff --git a/drivers/usb/gadget/config.c b/drivers/usb/gadget/config.c
index 09084fd..b2c0013 100644
--- a/drivers/usb/gadget/config.c
+++ b/drivers/usb/gadget/config.c
@@ -165,28 +165,3 @@ usb_copy_descriptors(struct usb_descriptor_header **src)
return ret;
}
-/**
- * usb_find_endpoint - find a copy of an endpoint descriptor
- * @src: original vector of descriptors
- * @copy: copy of @src
- * @match: endpoint descriptor found in @src
- *
- * This returns the copy of the @match descriptor made for @copy. Its
- * intended use is to help remembering the endpoint descriptor to use
- * when enabling a given endpoint.
- */
-struct usb_endpoint_descriptor *
-usb_find_endpoint(
- struct usb_descriptor_header **src,
- struct usb_descriptor_header **copy,
- struct usb_endpoint_descriptor *match
-)
-{
- while (*src) {
- if (*src == (void *) match)
- return (void *)*copy;
- src++;
- copy++;
- }
- return NULL;
-}
diff --git a/drivers/usb/gadget/f_acm.c b/drivers/usb/gadget/f_acm.c
index d04b4a6..3f88493 100644
--- a/drivers/usb/gadget/f_acm.c
+++ b/drivers/usb/gadget/f_acm.c
@@ -39,12 +39,6 @@
* descriptors (roughly equivalent to CDC Unions) may sometimes help.
*/
-struct acm_ep_descs {
- struct usb_endpoint_descriptor *in;
- struct usb_endpoint_descriptor *out;
- struct usb_endpoint_descriptor *notify;
-};
-
struct f_acm {
struct gserial port;
u8 ctrl_id, data_id;
@@ -58,9 +52,6 @@ struct f_acm {
*/
spinlock_t lock;
- struct acm_ep_descs fs;
- struct acm_ep_descs hs;
-
struct usb_ep *notify;
struct usb_request *notify_req;
@@ -404,9 +395,8 @@ static int acm_set_alt(struct usb_function *f, unsigned intf, unsigned alt)
usb_ep_disable(acm->notify);
} else {
VDBG(cdev, "init acm ctrl interface %d\n", intf);
- acm->notify->desc = ep_choose(cdev->gadget,
- acm->hs.notify,
- acm->fs.notify);
+ if (config_ep_by_speed(cdev->gadget, f, acm->notify))
+ return -EINVAL;
}
usb_ep_enable(acm->notify);
acm->notify->driver_data = acm;
@@ -415,12 +405,17 @@ static int acm_set_alt(struct usb_function *f, unsigned intf, unsigned alt)
if (acm->port.in->driver_data) {
DBG(cdev, "reset acm ttyGS%d\n", acm->port_num);
gserial_disconnect(&acm->port);
- } else {
+ }
+ if (!acm->port.in->desc || !acm->port.out->desc) {
DBG(cdev, "activate acm ttyGS%d\n", acm->port_num);
- acm->port.in->desc = ep_choose(cdev->gadget,
- acm->hs.in, acm->fs.in);
- acm->port.out->desc = ep_choose(cdev->gadget,
- acm->hs.out, acm->fs.out);
+ if (config_ep_by_speed(cdev->gadget, f,
+ acm->port.in) ||
+ config_ep_by_speed(cdev->gadget, f,
+ acm->port.out)) {
+ acm->port.in->desc = NULL;
+ acm->port.out->desc = NULL;
+ return -EINVAL;
+ }
}
gserial_connect(&acm->port, acm->port_num);
@@ -628,18 +623,11 @@ acm_bind(struct usb_configuration *c, struct usb_function *f)
acm->notify_req->complete = acm_cdc_notify_complete;
acm->notify_req->context = acm;
- /* copy descriptors, and track endpoint copies */
+ /* copy descriptors */
f->descriptors = usb_copy_descriptors(acm_fs_function);
if (!f->descriptors)
goto fail;
- acm->fs.in = usb_find_endpoint(acm_fs_function,
- f->descriptors, &acm_fs_in_desc);
- acm->fs.out = usb_find_endpoint(acm_fs_function,
- f->descriptors, &acm_fs_out_desc);
- acm->fs.notify = usb_find_endpoint(acm_fs_function,
- f->descriptors, &acm_fs_notify_desc);
-
/* support all relevant hardware speeds... we expect that when
* hardware is dual speed, all bulk-capable endpoints work at
* both speeds
@@ -652,15 +640,8 @@ acm_bind(struct usb_configuration *c, struct usb_function *f)
acm_hs_notify_desc.bEndpointAddress =
acm_fs_notify_desc.bEndpointAddress;
- /* copy descriptors, and track endpoint copies */
+ /* copy descriptors */
f->hs_descriptors = usb_copy_descriptors(acm_hs_function);
-
- acm->hs.in = usb_find_endpoint(acm_hs_function,
- f->hs_descriptors, &acm_hs_in_desc);
- acm->hs.out = usb_find_endpoint(acm_hs_function,
- f->hs_descriptors, &acm_hs_out_desc);
- acm->hs.notify = usb_find_endpoint(acm_hs_function,
- f->hs_descriptors, &acm_hs_notify_desc);
}
DBG(cdev, "acm ttyGS%d: %s speed IN/%s OUT/%s NOTIFY/%s\n",
diff --git a/drivers/usb/gadget/f_ecm.c b/drivers/usb/gadget/f_ecm.c
index 7c996f2..ddedbc83 100644
--- a/drivers/usb/gadget/f_ecm.c
+++ b/drivers/usb/gadget/f_ecm.c
@@ -46,11 +46,6 @@
* and also means that a get_alt() method is required.
*/
-struct ecm_ep_descs {
- struct usb_endpoint_descriptor *in;
- struct usb_endpoint_descriptor *out;
- struct usb_endpoint_descriptor *notify;
-};
enum ecm_notify_state {
ECM_NOTIFY_NONE, /* don't notify */
@@ -64,9 +59,6 @@ struct f_ecm {
char ethaddr[14];
- struct ecm_ep_descs fs;
- struct ecm_ep_descs hs;
-
struct usb_ep *notify;
struct usb_request *notify_req;
u8 notify_state;
@@ -463,11 +455,11 @@ static int ecm_set_alt(struct usb_function *f, unsigned intf, unsigned alt)
if (ecm->notify->driver_data) {
VDBG(cdev, "reset ecm control %d\n", intf);
usb_ep_disable(ecm->notify);
- } else {
+ }
+ if (!(ecm->notify->desc)) {
VDBG(cdev, "init ecm ctrl %d\n", intf);
- ecm->notify->desc = ep_choose(cdev->gadget,
- ecm->hs.notify,
- ecm->fs.notify);
+ if (config_ep_by_speed(cdev->gadget, f, ecm->notify))
+ goto fail;
}
usb_ep_enable(ecm->notify);
ecm->notify->driver_data = ecm;
@@ -482,12 +474,17 @@ static int ecm_set_alt(struct usb_function *f, unsigned intf, unsigned alt)
gether_disconnect(&ecm->port);
}
- if (!ecm->port.in_ep->desc) {
+ if (!ecm->port.in_ep->desc ||
+ !ecm->port.out_ep->desc) {
DBG(cdev, "init ecm\n");
- ecm->port.in_ep->desc = ep_choose(cdev->gadget,
- ecm->hs.in, ecm->fs.in);
- ecm->port.out_ep->desc = ep_choose(cdev->gadget,
- ecm->hs.out, ecm->fs.out);
+ if (config_ep_by_speed(cdev->gadget, f,
+ ecm->port.in_ep) ||
+ config_ep_by_speed(cdev->gadget, f,
+ ecm->port.out_ep)) {
+ ecm->port.in_ep->desc = NULL;
+ ecm->port.out_ep->desc = NULL;
+ goto fail;
+ }
}
/* CDC Ethernet only sends data in non-default altsettings.
@@ -664,13 +661,6 @@ ecm_bind(struct usb_configuration *c, struct usb_function *f)
if (!f->descriptors)
goto fail;
- ecm->fs.in = usb_find_endpoint(ecm_fs_function,
- f->descriptors, &fs_ecm_in_desc);
- ecm->fs.out = usb_find_endpoint(ecm_fs_function,
- f->descriptors, &fs_ecm_out_desc);
- ecm->fs.notify = usb_find_endpoint(ecm_fs_function,
- f->descriptors, &fs_ecm_notify_desc);
-
/* support all relevant hardware speeds... we expect that when
* hardware is dual speed, all bulk-capable endpoints work at
* both speeds
@@ -687,13 +677,6 @@ ecm_bind(struct usb_configuration *c, struct usb_function *f)
f->hs_descriptors = usb_copy_descriptors(ecm_hs_function);
if (!f->hs_descriptors)
goto fail;
-
- ecm->hs.in = usb_find_endpoint(ecm_hs_function,
- f->hs_descriptors, &hs_ecm_in_desc);
- ecm->hs.out = usb_find_endpoint(ecm_hs_function,
- f->hs_descriptors, &hs_ecm_out_desc);
- ecm->hs.notify = usb_find_endpoint(ecm_hs_function,
- f->hs_descriptors, &hs_ecm_notify_desc);
}
/* NOTE: all that is done without knowing or caring about
diff --git a/drivers/usb/gadget/f_eem.c b/drivers/usb/gadget/f_eem.c
index fea8e3b..3e41274 100644
--- a/drivers/usb/gadget/f_eem.c
+++ b/drivers/usb/gadget/f_eem.c
@@ -35,17 +35,9 @@
* Ethernet link.
*/
-struct eem_ep_descs {
- struct usb_endpoint_descriptor *in;
- struct usb_endpoint_descriptor *out;
-};
-
struct f_eem {
struct gether port;
u8 ctrl_id;
-
- struct eem_ep_descs fs;
- struct eem_ep_descs hs;
};
static inline struct f_eem *func_to_eem(struct usb_function *f)
@@ -176,12 +168,16 @@ static int eem_set_alt(struct usb_function *f, unsigned intf, unsigned alt)
gether_disconnect(&eem->port);
}
- if (!eem->port.in_ep->desc) {
+ if (!eem->port.in_ep->desc || !eem->port.out_ep->desc) {
DBG(cdev, "init eem\n");
- eem->port.in_ep->desc = ep_choose(cdev->gadget,
- eem->hs.in, eem->fs.in);
- eem->port.out_ep->desc = ep_choose(cdev->gadget,
- eem->hs.out, eem->fs.out);
+ if (config_ep_by_speed(cdev->gadget, f,
+ eem->port.in_ep) ||
+ config_ep_by_speed(cdev->gadget, f,
+ eem->port.out_ep)) {
+ eem->port.in_ep->desc = NULL;
+ eem->port.out_ep->desc = NULL;
+ goto fail;
+ }
}
/* zlps should not occur because zero-length EEM packets
@@ -253,11 +249,6 @@ eem_bind(struct usb_configuration *c, struct usb_function *f)
if (!f->descriptors)
goto fail;
- eem->fs.in = usb_find_endpoint(eem_fs_function,
- f->descriptors, &eem_fs_in_desc);
- eem->fs.out = usb_find_endpoint(eem_fs_function,
- f->descriptors, &eem_fs_out_desc);
-
/* support all relevant hardware speeds... we expect that when
* hardware is dual speed, all bulk-capable endpoints work at
* both speeds
@@ -272,11 +263,6 @@ eem_bind(struct usb_configuration *c, struct usb_function *f)
f->hs_descriptors = usb_copy_descriptors(eem_hs_function);
if (!f->hs_descriptors)
goto fail;
-
- eem->hs.in = usb_find_endpoint(eem_hs_function,
- f->hs_descriptors, &eem_hs_in_desc);
- eem->hs.out = usb_find_endpoint(eem_hs_function,
- f->hs_descriptors, &eem_hs_out_desc);
}
DBG(cdev, "CDC Ethernet (EEM): %s speed IN/%s OUT/%s\n",
diff --git a/drivers/usb/gadget/f_hid.c b/drivers/usb/gadget/f_hid.c
index 12879b6..403a48b 100644
--- a/drivers/usb/gadget/f_hid.c
+++ b/drivers/usb/gadget/f_hid.c
@@ -59,8 +59,6 @@ struct f_hidg {
struct cdev cdev;
struct usb_function func;
struct usb_ep *in_ep;
- struct usb_endpoint_descriptor *fs_in_ep_desc;
- struct usb_endpoint_descriptor *hs_in_ep_desc;
};
static inline struct f_hidg *func_to_hidg(struct usb_function *f)
@@ -425,8 +423,12 @@ static int hidg_set_alt(struct usb_function *f, unsigned intf, unsigned alt)
if (hidg->in_ep->driver_data != NULL)
usb_ep_disable(hidg->in_ep);
- hidg->in_ep->desc = ep_choose(f->config->cdev->gadget,
- hidg->hs_in_ep_desc, hidg->fs_in_ep_desc);
+ status = config_ep_by_speed(f->config->cdev->gadget, f,
+ hidg->in_ep);
+ if (status) {
+ ERROR(cdev, "config_ep_by_speed FAILED!\n");
+ goto fail;
+ }
status = usb_ep_enable(hidg->in_ep);
if (status < 0) {
ERROR(cdev, "Enable endpoint FAILED!\n");
@@ -497,21 +499,12 @@ static int __init hidg_bind(struct usb_configuration *c, struct usb_function *f)
if (!f->descriptors)
goto fail;
- hidg->fs_in_ep_desc = usb_find_endpoint(hidg_fs_descriptors,
- f->descriptors,
- &hidg_fs_in_ep_desc);
-
if (gadget_is_dualspeed(c->cdev->gadget)) {
hidg_hs_in_ep_desc.bEndpointAddress =
hidg_fs_in_ep_desc.bEndpointAddress;
f->hs_descriptors = usb_copy_descriptors(hidg_hs_descriptors);
if (!f->hs_descriptors)
goto fail;
- hidg->hs_in_ep_desc = usb_find_endpoint(hidg_hs_descriptors,
- f->hs_descriptors,
- &hidg_hs_in_ep_desc);
- } else {
- hidg->hs_in_ep_desc = NULL;
}
mutex_init(&hidg->lock);
diff --git a/drivers/usb/gadget/f_loopback.c b/drivers/usb/gadget/f_loopback.c
index 34e3cca..3756326 100644
--- a/drivers/usb/gadget/f_loopback.c
+++ b/drivers/usb/gadget/f_loopback.c
@@ -256,8 +256,9 @@ enable_loopback(struct usb_composite_dev *cdev, struct f_loopback *loop)
/* one endpoint writes data back IN to the host */
ep = loop->in_ep;
- ep->desc = ep_choose(cdev->gadget,
- &hs_loop_source_desc, &fs_loop_source_desc);
+ result = config_ep_by_speed(cdev->gadget, &(loop->function), ep);
+ if (result)
+ return result;
result = usb_ep_enable(ep);
if (result < 0)
return result;
@@ -265,8 +266,10 @@ enable_loopback(struct usb_composite_dev *cdev, struct f_loopback *loop)
/* one endpoint just reads OUT packets */
ep = loop->out_ep;
- ep->desc = ep_choose(cdev->gadget,
- &hs_loop_sink_desc, &fs_loop_sink_desc);
+ result = config_ep_by_speed(cdev->gadget, &(loop->function), ep);
+ if (result)
+ goto fail0;
+
result = usb_ep_enable(ep);
if (result < 0) {
fail0:
diff --git a/drivers/usb/gadget/f_mass_storage.c b/drivers/usb/gadget/f_mass_storage.c
index 4eee434..5b93395 100644
--- a/drivers/usb/gadget/f_mass_storage.c
+++ b/drivers/usb/gadget/f_mass_storage.c
@@ -2324,19 +2324,6 @@ static int get_next_command(struct fsg_common *common)
/*-------------------------------------------------------------------------*/
-static int enable_endpoint(struct fsg_common *common, struct usb_ep *ep,
- const struct usb_endpoint_descriptor *d)
-{
- int rc;
-
- ep->driver_data = common;
- ep->desc = (struct usb_endpoint_descriptor *)d;
- rc = usb_ep_enable(ep);
- if (rc)
- ERROR(common, "can't enable %s, result %d\n", ep->name, rc);
- return rc;
-}
-
static int alloc_request(struct fsg_common *common, struct usb_ep *ep,
struct usb_request **preq)
{
@@ -2350,7 +2337,6 @@ static int alloc_request(struct fsg_common *common, struct usb_ep *ep,
/* Reset interface setting and re-init endpoint state (toggle etc). */
static int do_set_interface(struct fsg_common *common, struct fsg_dev *new_fsg)
{
- const struct usb_endpoint_descriptor *d;
struct fsg_dev *fsg;
int i, rc = 0;
@@ -2397,20 +2383,26 @@ reset:
fsg = common->fsg;
/* Enable the endpoints */
- d = fsg_ep_desc(common->gadget,
- &fsg_fs_bulk_in_desc, &fsg_hs_bulk_in_desc);
- rc = enable_endpoint(common, fsg->bulk_in, d);
+ rc = config_ep_by_speed(common->gadget, &(fsg->function), fsg->bulk_in);
+ if (rc)
+ goto reset;
+ rc = usb_ep_enable(fsg->bulk_in);
if (rc)
goto reset;
+ fsg->bulk_in->driver_data = common;
fsg->bulk_in_enabled = 1;
- d = fsg_ep_desc(common->gadget,
- &fsg_fs_bulk_out_desc, &fsg_hs_bulk_out_desc);
- rc = enable_endpoint(common, fsg->bulk_out, d);
+ rc = config_ep_by_speed(common->gadget, &(fsg->function),
+ fsg->bulk_out);
+ if (rc)
+ goto reset;
+ rc = usb_ep_enable(fsg->bulk_out);
if (rc)
goto reset;
+ fsg->bulk_out->driver_data = common;
fsg->bulk_out_enabled = 1;
- common->bulk_out_maxpacket = le16_to_cpu(d->wMaxPacketSize);
+ common->bulk_out_maxpacket =
+ le16_to_cpu(fsg->bulk_out->desc->wMaxPacketSize);
clear_bit(IGNORE_BULK_OUT, &fsg->atomic_bitflags);
/* Allocate the requests */
diff --git a/drivers/usb/gadget/f_ncm.c b/drivers/usb/gadget/f_ncm.c
index 06daa1b..ae69ed7 100644
--- a/drivers/usb/gadget/f_ncm.c
+++ b/drivers/usb/gadget/f_ncm.c
@@ -48,12 +48,6 @@
#define NCM_NDP_HDR_CRC 0x01000000
#define NCM_NDP_HDR_NOCRC 0x00000000
-struct ncm_ep_descs {
- struct usb_endpoint_descriptor *in;
- struct usb_endpoint_descriptor *out;
- struct usb_endpoint_descriptor *notify;
-};
-
enum ncm_notify_state {
NCM_NOTIFY_NONE, /* don't notify */
NCM_NOTIFY_CONNECT, /* issue CONNECT next */
@@ -66,9 +60,6 @@ struct f_ncm {
char ethaddr[14];
- struct ncm_ep_descs fs;
- struct ncm_ep_descs hs;
-
struct usb_ep *notify;
struct usb_request *notify_req;
u8 notify_state;
@@ -801,11 +792,12 @@ static int ncm_set_alt(struct usb_function *f, unsigned intf, unsigned alt)
if (ncm->notify->driver_data) {
DBG(cdev, "reset ncm control %d\n", intf);
usb_ep_disable(ncm->notify);
- } else {
+ }
+
+ if (!(ncm->notify->desc)) {
DBG(cdev, "init ncm ctrl %d\n", intf);
- ncm->notify->desc = ep_choose(cdev->gadget,
- ncm->hs.notify,
- ncm->fs.notify);
+ if (config_ep_by_speed(cdev->gadget, f, ncm->notify))
+ goto fail;
}
usb_ep_enable(ncm->notify);
ncm->notify->driver_data = ncm;
@@ -828,14 +820,17 @@ static int ncm_set_alt(struct usb_function *f, unsigned intf, unsigned alt)
if (alt == 1) {
struct net_device *net;
- if (!ncm->port.in_ep->desc) {
+ if (!ncm->port.in_ep->desc ||
+ !ncm->port.out_ep->desc) {
DBG(cdev, "init ncm\n");
- ncm->port.in_ep->desc = ep_choose(cdev->gadget,
- ncm->hs.in,
- ncm->fs.in);
- ncm->port.out_ep->desc = ep_choose(cdev->gadget,
- ncm->hs.out,
- ncm->fs.out);
+ if (config_ep_by_speed(cdev->gadget, f,
+ ncm->port.in_ep) ||
+ config_ep_by_speed(cdev->gadget, f,
+ ncm->port.out_ep)) {
+ ncm->port.in_ep->desc = NULL;
+ ncm->port.out_ep->desc = NULL;
+ goto fail;
+ }
}
/* TODO */
@@ -1227,13 +1222,6 @@ ncm_bind(struct usb_configuration *c, struct usb_function *f)
if (!f->descriptors)
goto fail;
- ncm->fs.in = usb_find_endpoint(ncm_fs_function,
- f->descriptors, &fs_ncm_in_desc);
- ncm->fs.out = usb_find_endpoint(ncm_fs_function,
- f->descriptors, &fs_ncm_out_desc);
- ncm->fs.notify = usb_find_endpoint(ncm_fs_function,
- f->descriptors, &fs_ncm_notify_desc);
-
/*
* support all relevant hardware speeds... we expect that when
* hardware is dual speed, all bulk-capable endpoints work at
@@ -1251,13 +1239,6 @@ ncm_bind(struct usb_configuration *c, struct usb_function *f)
f->hs_descriptors = usb_copy_descriptors(ncm_hs_function);
if (!f->hs_descriptors)
goto fail;
-
- ncm->hs.in = usb_find_endpoint(ncm_hs_function,
- f->hs_descriptors, &hs_ncm_in_desc);
- ncm->hs.out = usb_find_endpoint(ncm_hs_function,
- f->hs_descriptors, &hs_ncm_out_desc);
- ncm->hs.notify = usb_find_endpoint(ncm_hs_function,
- f->hs_descriptors, &hs_ncm_notify_desc);
}
/*
diff --git a/drivers/usb/gadget/f_obex.c b/drivers/usb/gadget/f_obex.c
index a6dbda09..394502a 100644
--- a/drivers/usb/gadget/f_obex.c
+++ b/drivers/usb/gadget/f_obex.c
@@ -39,20 +39,12 @@
* ready to handle the commands.
*/
-struct obex_ep_descs {
- struct usb_endpoint_descriptor *obex_in;
- struct usb_endpoint_descriptor *obex_out;
-};
-
struct f_obex {
struct gserial port;
u8 ctrl_id;
u8 data_id;
u8 port_num;
u8 can_activate;
-
- struct obex_ep_descs fs;
- struct obex_ep_descs hs;
};
static inline struct f_obex *func_to_obex(struct usb_function *f)
@@ -227,12 +219,16 @@ static int obex_set_alt(struct usb_function *f, unsigned intf, unsigned alt)
gserial_disconnect(&obex->port);
}
- if (!obex->port.in->desc) {
+ if (!obex->port.in->desc || !obex->port.out->desc) {
DBG(cdev, "init obex ttyGS%d\n", obex->port_num);
- obex->port.in->desc = ep_choose(cdev->gadget,
- obex->hs.obex_in, obex->fs.obex_in);
- obex->port.out->desc = ep_choose(cdev->gadget,
- obex->hs.obex_out, obex->fs.obex_out);
+ if (config_ep_by_speed(cdev->gadget, f,
+ obex->port.in) ||
+ config_ep_by_speed(cdev->gadget, f,
+ obex->port.out)) {
+ obex->port.out->desc = NULL;
+ obex->port.in->desc = NULL;
+ goto fail;
+ }
}
if (alt == 1) {
@@ -346,11 +342,6 @@ obex_bind(struct usb_configuration *c, struct usb_function *f)
/* copy descriptors, and track endpoint copies */
f->descriptors = usb_copy_descriptors(fs_function);
- obex->fs.obex_in = usb_find_endpoint(fs_function,
- f->descriptors, &obex_fs_ep_in_desc);
- obex->fs.obex_out = usb_find_endpoint(fs_function,
- f->descriptors, &obex_fs_ep_out_desc);
-
/* support all relevant hardware speeds... we expect that when
* hardware is dual speed, all bulk-capable endpoints work at
* both speeds
@@ -364,11 +355,6 @@ obex_bind(struct usb_configuration *c, struct usb_function *f)
/* copy descriptors, and track endpoint copies */
f->hs_descriptors = usb_copy_descriptors(hs_function);
-
- obex->hs.obex_in = usb_find_endpoint(hs_function,
- f->hs_descriptors, &obex_hs_ep_in_desc);
- obex->hs.obex_out = usb_find_endpoint(hs_function,
- f->hs_descriptors, &obex_hs_ep_out_desc);
}
/* Avoid letting this gadget enumerate until the userspace
diff --git a/drivers/usb/gadget/f_phonet.c b/drivers/usb/gadget/f_phonet.c
index dc63f16..0d6d260 100644
--- a/drivers/usb/gadget/f_phonet.c
+++ b/drivers/usb/gadget/f_phonet.c
@@ -429,12 +429,12 @@ static int pn_set_alt(struct usb_function *f, unsigned intf, unsigned alt)
if (alt == 1) {
int i;
- fp->out_ep->desc = ep_choose(gadget,
- &pn_hs_sink_desc,
- &pn_fs_sink_desc);
- fp->in_ep->desc = ep_choose(gadget,
- &pn_hs_source_desc,
- &pn_fs_source_desc);
+ if (config_ep_by_speed(gadget, f, fp->in_ep) ||
+ config_ep_by_speed(gadget, f, fp->out_ep)) {
+ fp->in_ep->desc = NULL;
+ fp->out_ep->desc = NULL;
+ return -EINVAL;
+ }
usb_ep_enable(fp->out_ep);
usb_ep_enable(fp->in_ep);
diff --git a/drivers/usb/gadget/f_rndis.c b/drivers/usb/gadget/f_rndis.c
index 4646254..b324efa 100644
--- a/drivers/usb/gadget/f_rndis.c
+++ b/drivers/usb/gadget/f_rndis.c
@@ -76,21 +76,12 @@
* - MS-Windows drivers sometimes emit undocumented requests.
*/
-struct rndis_ep_descs {
- struct usb_endpoint_descriptor *in;
- struct usb_endpoint_descriptor *out;
- struct usb_endpoint_descriptor *notify;
-};
-
struct f_rndis {
struct gether port;
u8 ctrl_id, data_id;
u8 ethaddr[ETH_ALEN];
int config;
- struct rndis_ep_descs fs;
- struct rndis_ep_descs hs;
-
struct usb_ep *notify;
struct usb_request *notify_req;
atomic_t notify_count;
@@ -483,11 +474,11 @@ static int rndis_set_alt(struct usb_function *f, unsigned intf, unsigned alt)
if (rndis->notify->driver_data) {
VDBG(cdev, "reset rndis control %d\n", intf);
usb_ep_disable(rndis->notify);
- } else {
+ }
+ if (!rndis->notify->desc) {
VDBG(cdev, "init rndis ctrl %d\n", intf);
- rndis->notify->desc = ep_choose(cdev->gadget,
- rndis->hs.notify,
- rndis->fs.notify);
+ if (config_ep_by_speed(cdev->gadget, f, rndis->notify))
+ goto fail;
}
usb_ep_enable(rndis->notify);
rndis->notify->driver_data = rndis;
@@ -500,12 +491,16 @@ static int rndis_set_alt(struct usb_function *f, unsigned intf, unsigned alt)
gether_disconnect(&rndis->port);
}
- if (!rndis->port.in_ep->desc) {
+ if (!rndis->port.in_ep->desc || !rndis->port.out_ep->desc) {
DBG(cdev, "init rndis\n");
- rndis->port.in_ep->desc = ep_choose(cdev->gadget,
- rndis->hs.in, rndis->fs.in);
- rndis->port.out_ep->desc = ep_choose(cdev->gadget,
- rndis->hs.out, rndis->fs.out);
+ if (config_ep_by_speed(cdev->gadget, f,
+ rndis->port.in_ep) ||
+ config_ep_by_speed(cdev->gadget, f,
+ rndis->port.out_ep)) {
+ rndis->port.in_ep->desc = NULL;
+ rndis->port.out_ep->desc = NULL;
+ goto fail;
+ }
}
/* Avoid ZLPs; they can be troublesome. */
@@ -661,13 +656,6 @@ rndis_bind(struct usb_configuration *c, struct usb_function *f)
if (!f->descriptors)
goto fail;
- rndis->fs.in = usb_find_endpoint(eth_fs_function,
- f->descriptors, &fs_in_desc);
- rndis->fs.out = usb_find_endpoint(eth_fs_function,
- f->descriptors, &fs_out_desc);
- rndis->fs.notify = usb_find_endpoint(eth_fs_function,
- f->descriptors, &fs_notify_desc);
-
/* support all relevant hardware speeds... we expect that when
* hardware is dual speed, all bulk-capable endpoints work at
* both speeds
@@ -685,13 +673,6 @@ rndis_bind(struct usb_configuration *c, struct usb_function *f)
if (!f->hs_descriptors)
goto fail;
-
- rndis->hs.in = usb_find_endpoint(eth_hs_function,
- f->hs_descriptors, &hs_in_desc);
- rndis->hs.out = usb_find_endpoint(eth_hs_function,
- f->hs_descriptors, &hs_out_desc);
- rndis->hs.notify = usb_find_endpoint(eth_hs_function,
- f->hs_descriptors, &hs_notify_desc);
}
rndis->port.open = rndis_open;
diff --git a/drivers/usb/gadget/f_serial.c b/drivers/usb/gadget/f_serial.c
index a9ce626..91fdf79 100644
--- a/drivers/usb/gadget/f_serial.c
+++ b/drivers/usb/gadget/f_serial.c
@@ -27,18 +27,10 @@
* if you can arrange appropriate host side drivers.
*/
-struct gser_descs {
- struct usb_endpoint_descriptor *in;
- struct usb_endpoint_descriptor *out;
-};
-
struct f_gser {
struct gserial port;
u8 data_id;
u8 port_num;
-
- struct gser_descs fs;
- struct gser_descs hs;
};
static inline struct f_gser *func_to_gser(struct usb_function *f)
@@ -136,12 +128,15 @@ static int gser_set_alt(struct usb_function *f, unsigned intf, unsigned alt)
if (gser->port.in->driver_data) {
DBG(cdev, "reset generic ttyGS%d\n", gser->port_num);
gserial_disconnect(&gser->port);
- } else {
+ }
+ if (!gser->port.in->desc || !gser->port.out->desc) {
DBG(cdev, "activate generic ttyGS%d\n", gser->port_num);
- gser->port.in->desc = ep_choose(cdev->gadget,
- gser->hs.in, gser->fs.in);
- gser->port.out->desc = ep_choose(cdev->gadget,
- gser->hs.out, gser->fs.out);
+ if (!config_ep_by_speed(cdev->gadget, f, gser->port.in) ||
+ !config_ep_by_speed(cdev->gadget, f, gser->port.out)) {
+ gser->port.in->desc = NULL;
+ gser->port.out->desc = NULL;
+ return -EINVAL;
+ }
}
gserial_connect(&gser->port, gser->port_num);
return 0;
@@ -193,12 +188,6 @@ gser_bind(struct usb_configuration *c, struct usb_function *f)
/* copy descriptors, and track endpoint copies */
f->descriptors = usb_copy_descriptors(gser_fs_function);
- gser->fs.in = usb_find_endpoint(gser_fs_function,
- f->descriptors, &gser_fs_in_desc);
- gser->fs.out = usb_find_endpoint(gser_fs_function,
- f->descriptors, &gser_fs_out_desc);
-
-
/* support all relevant hardware speeds... we expect that when
* hardware is dual speed, all bulk-capable endpoints work at
* both speeds
@@ -211,11 +200,6 @@ gser_bind(struct usb_configuration *c, struct usb_function *f)
/* copy descriptors, and track endpoint copies */
f->hs_descriptors = usb_copy_descriptors(gser_hs_function);
-
- gser->hs.in = usb_find_endpoint(gser_hs_function,
- f->hs_descriptors, &gser_hs_in_desc);
- gser->hs.out = usb_find_endpoint(gser_hs_function,
- f->hs_descriptors, &gser_hs_out_desc);
}
DBG(cdev, "generic ttyGS%d: %s speed IN/%s OUT/%s\n",
diff --git a/drivers/usb/gadget/f_sourcesink.c b/drivers/usb/gadget/f_sourcesink.c
index 0ffddd3..caf2f95 100644
--- a/drivers/usb/gadget/f_sourcesink.c
+++ b/drivers/usb/gadget/f_sourcesink.c
@@ -347,7 +347,9 @@ enable_source_sink(struct usb_composite_dev *cdev, struct f_sourcesink *ss)
/* one endpoint writes (sources) zeroes IN (to the host) */
ep = ss->in_ep;
- ep->desc = ep_choose(cdev->gadget, &hs_source_desc, &fs_source_desc);
+ result = config_ep_by_speed(cdev->gadget, &(ss->function), ep);
+ if (result)
+ return result;
result = usb_ep_enable(ep);
if (result < 0)
return result;
@@ -364,7 +366,9 @@ fail:
/* one endpoint reads (sinks) anything OUT (from the host) */
ep = ss->out_ep;
- ep->desc = ep_choose(cdev->gadget, &hs_sink_desc, &fs_sink_desc);
+ result = config_ep_by_speed(cdev->gadget, &(ss->function), ep);
+ if (result)
+ goto fail;
result = usb_ep_enable(ep);
if (result < 0)
goto fail;
diff --git a/drivers/usb/gadget/f_subset.c b/drivers/usb/gadget/f_subset.c
index aecaed1..93bf676 100644
--- a/drivers/usb/gadget/f_subset.c
+++ b/drivers/usb/gadget/f_subset.c
@@ -57,18 +57,10 @@
* caring about specific product and vendor IDs.
*/
-struct geth_descs {
- struct usb_endpoint_descriptor *in;
- struct usb_endpoint_descriptor *out;
-};
-
struct f_gether {
struct gether port;
char ethaddr[14];
-
- struct geth_descs fs;
- struct geth_descs hs;
};
static inline struct f_gether *func_to_geth(struct usb_function *f)
@@ -243,10 +235,12 @@ static int geth_set_alt(struct usb_function *f, unsigned intf, unsigned alt)
}
DBG(cdev, "init + activate cdc subset\n");
- geth->port.in_ep->desc = ep_choose(cdev->gadget,
- geth->hs.in, geth->fs.in);
- geth->port.out_ep->desc = ep_choose(cdev->gadget,
- geth->hs.out, geth->fs.out);
+ if (config_ep_by_speed(cdev->gadget, f, geth->port.in_ep) ||
+ config_ep_by_speed(cdev->gadget, f, geth->port.out_ep)) {
+ geth->port.in_ep->desc = NULL;
+ geth->port.out_ep->desc = NULL;
+ return -EINVAL;
+ }
net = gether_connect(&geth->port);
return IS_ERR(net) ? PTR_ERR(net) : 0;
@@ -297,12 +291,6 @@ geth_bind(struct usb_configuration *c, struct usb_function *f)
/* copy descriptors, and track endpoint copies */
f->descriptors = usb_copy_descriptors(fs_eth_function);
- geth->fs.in = usb_find_endpoint(fs_eth_function,
- f->descriptors, &fs_subset_in_desc);
- geth->fs.out = usb_find_endpoint(fs_eth_function,
- f->descriptors, &fs_subset_out_desc);
-
-
/* support all relevant hardware speeds... we expect that when
* hardware is dual speed, all bulk-capable endpoints work at
* both speeds
@@ -315,11 +303,6 @@ geth_bind(struct usb_configuration *c, struct usb_function *f)
/* copy descriptors, and track endpoint copies */
f->hs_descriptors = usb_copy_descriptors(hs_eth_function);
-
- geth->hs.in = usb_find_endpoint(hs_eth_function,
- f->hs_descriptors, &hs_subset_in_desc);
- geth->hs.out = usb_find_endpoint(hs_eth_function,
- f->hs_descriptors, &hs_subset_out_desc);
}
/* NOTE: all that is done without knowing or caring about
diff --git a/include/linux/usb/composite.h b/include/linux/usb/composite.h
index 324fbc7..5564d5e 100644
--- a/include/linux/usb/composite.h
+++ b/include/linux/usb/composite.h
@@ -166,21 +166,6 @@ int usb_interface_id(struct usb_configuration *, struct usb_function *);
int config_ep_by_speed(struct usb_gadget *g, struct usb_function *f,
struct usb_ep *_ep);
-/**
- * ep_choose - select descriptor endpoint at current device speed
- * @g: gadget, connected and running at some speed
- * @hs: descriptor to use for high speed operation
- * @fs: descriptor to use for full or low speed operation
- */
-static inline struct usb_endpoint_descriptor *
-ep_choose(struct usb_gadget *g, struct usb_endpoint_descriptor *hs,
- struct usb_endpoint_descriptor *fs)
-{
- if (gadget_is_dualspeed(g) && g->speed == USB_SPEED_HIGH)
- return hs;
- return fs;
-}
-
#define MAX_CONFIG_INTERFACES 16 /* arbitrary; max 255 */
/**
diff --git a/include/linux/usb/gadget.h b/include/linux/usb/gadget.h
index 8015ceb..318c815 100644
--- a/include/linux/usb/gadget.h
+++ b/include/linux/usb/gadget.h
@@ -871,12 +871,6 @@ int usb_gadget_config_buf(const struct usb_config_descriptor *config,
struct usb_descriptor_header **usb_copy_descriptors(
struct usb_descriptor_header **);
-/* return copy of endpoint descriptor given original descriptor set */
-struct usb_endpoint_descriptor *usb_find_endpoint(
- struct usb_descriptor_header **src,
- struct usb_descriptor_header **copy,
- struct usb_endpoint_descriptor *match);
-
/**
* usb_free_descriptors - free descriptors returned by usb_copy_descriptors()
* @v: vector of descriptors
--
1.7.3.3
--
Sent by an employee of the Qualcomm Innovation Center, Inc.
The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum.
^ permalink raw reply related [flat|nested] 13+ messages in thread* [PATCH v11 4/7] usb:gadget: Add SuperSpeed support to the Gadget Framework
[not found] <1305805417-31750-1-git-send-email-tlinder@codeaurora.org>
` (2 preceding siblings ...)
2011-05-19 11:43 ` [PATCH/RESEND v11 3/7] usb: Modify existing gadget drivers to use config_ep_by_speed() instead of ep_choose Tatyana Brokhman
@ 2011-05-19 11:43 ` Tatyana Brokhman
2011-05-20 16:49 ` Sebastian Andrzej Siewior
2011-05-19 11:43 ` [PATCH/RESEND v11 5/7] usb: Add streams support to the gadget framework Tatyana Brokhman
` (2 subsequent siblings)
6 siblings, 1 reply; 13+ messages in thread
From: Tatyana Brokhman @ 2011-05-19 11:43 UTC (permalink / raw)
To: greg; +Cc: linux-usb, balbi, ablay, linux-arm-msm, Tatyana Brokhman,
open list
This patch adds the SuperSpeed functionality to the gadget framework.
Support for new SuperSpeed BOS descriptor was added.
Support for SET_FEATURE and GET_STATUS requests in SuperSpeed mode was
added.
Signed-off-by: Tatyana Brokhman <tlinder@codeaurora.org>
---
drivers/usb/gadget/Kconfig | 11 ++
drivers/usb/gadget/composite.c | 257 ++++++++++++++++++++++++++++++++++++---
drivers/usb/gadget/epautoconf.c | 7 +-
include/linux/usb/ch9.h | 2 -
include/linux/usb/composite.h | 16 +++
include/linux/usb/gadget.h | 34 +++++
6 files changed, 304 insertions(+), 23 deletions(-)
diff --git a/drivers/usb/gadget/Kconfig b/drivers/usb/gadget/Kconfig
index 58456d1..61aa0ff 100644
--- a/drivers/usb/gadget/Kconfig
+++ b/drivers/usb/gadget/Kconfig
@@ -640,6 +640,17 @@ config USB_GADGET_DUALSPEED
Means that gadget drivers should include extra descriptors
and code to handle dual-speed controllers.
+config USB_GADGET_SUPERSPEED
+ boolean "Gadget operating in Super Speed"
+ depends on USB_GADGET
+ depends on USB_GADGET_DUALSPEED
+ help
+ Enabling this feature enables Super Speed support in the Gadget
+ driver. It means that gadget drivers should provide extra (SuperSpeed)
+ descriptors to the host.
+ For composite devices: if SuperSpeed descriptors weren't supplied by
+ the FD, they will be automatically generated with default values.
+
#
# USB Gadget Drivers
#
diff --git a/drivers/usb/gadget/composite.c b/drivers/usb/gadget/composite.c
index cfba1ee..bd811ac 100644
--- a/drivers/usb/gadget/composite.c
+++ b/drivers/usb/gadget/composite.c
@@ -129,6 +129,9 @@ int config_ep_by_speed(struct usb_gadget *g,
struct usb_endpoint_descriptor *chosen_desc = NULL;
struct usb_descriptor_header **speed_desc = NULL;
+ struct usb_ss_ep_comp_descriptor *comp_desc = NULL;
+ int want_comp_desc = 0;
+
struct usb_descriptor_header **d_spd; /* cursor for speed desc */
if (!g || !f || !_ep)
@@ -136,6 +139,13 @@ int config_ep_by_speed(struct usb_gadget *g,
/* select desired speed */
switch (g->speed) {
+ case USB_SPEED_SUPER:
+ if (gadget_is_superspeed(g)) {
+ speed_desc = f->ss_descriptors;
+ want_comp_desc = 1;
+ break;
+ }
+ /* else: Fall trough */
case USB_SPEED_HIGH:
if (gadget_is_dualspeed(g)) {
speed_desc = f->hs_descriptors;
@@ -157,7 +167,35 @@ ep_found:
/* commit results */
_ep->maxpacket = le16_to_cpu(chosen_desc->wMaxPacketSize);
_ep->desc = chosen_desc;
-
+ _ep->comp_desc = NULL;
+ _ep->maxburst = 0;
+ _ep->mult = 0;
+ if (want_comp_desc) {
+ /*
+ * Companion descriptor should follow EP descriptor
+ * USB 3.0 spec, #9.6.7
+ */
+ comp_desc = (struct usb_ss_ep_comp_descriptor *)*(++d_spd);
+ if (!comp_desc ||
+ (comp_desc->bDescriptorType != USB_DT_SS_ENDPOINT_COMP))
+ return -EIO;
+ _ep->comp_desc = comp_desc;
+ if (g->speed == USB_SPEED_SUPER) {
+ switch (usb_endpoint_type(_ep->desc)) {
+ case USB_ENDPOINT_XFER_BULK:
+ case USB_ENDPOINT_XFER_INT:
+ _ep->maxburst = comp_desc->bMaxBurst;
+ break;
+ case USB_ENDPOINT_XFER_ISOC:
+ /* mult: bits 1:0 of bmAttributes */
+ _ep->mult = comp_desc->bmAttributes & 0x3;
+ break;
+ default:
+ /* Do nothing for control endpoints */
+ break;
+ }
+ }
+ }
return 0;
}
@@ -209,6 +247,8 @@ int usb_add_function(struct usb_configuration *config,
config->fullspeed = true;
if (!config->highspeed && function->hs_descriptors)
config->highspeed = true;
+ if (!config->superspeed && function->ss_descriptors)
+ config->superspeed = true;
done:
if (value)
@@ -352,10 +392,17 @@ static int config_buf(struct usb_configuration *config,
list_for_each_entry(f, &config->functions, list) {
struct usb_descriptor_header **descriptors;
- if (speed == USB_SPEED_HIGH)
+ switch (speed) {
+ case USB_SPEED_SUPER:
+ descriptors = f->ss_descriptors;
+ break;
+ case USB_SPEED_HIGH:
descriptors = f->hs_descriptors;
- else
+ break;
+ default:
descriptors = f->descriptors;
+ }
+
if (!descriptors)
continue;
status = usb_descriptor_fillbuf(next, len,
@@ -378,9 +425,10 @@ static int config_desc(struct usb_composite_dev *cdev, unsigned w_value)
u8 type = w_value >> 8;
enum usb_device_speed speed = USB_SPEED_UNKNOWN;
- if (gadget_is_dualspeed(gadget)) {
- int hs = 0;
-
+ if (gadget->speed == USB_SPEED_SUPER)
+ speed = gadget->speed;
+ else if (gadget_is_dualspeed(gadget)) {
+ int hs = 0;
if (gadget->speed == USB_SPEED_HIGH)
hs = 1;
if (type == USB_DT_OTHER_SPEED_CONFIG)
@@ -394,13 +442,20 @@ static int config_desc(struct usb_composite_dev *cdev, unsigned w_value)
w_value &= 0xff;
list_for_each_entry(c, &cdev->configs, list) {
/* ignore configs that won't work at this speed */
- if (speed == USB_SPEED_HIGH) {
+ switch (speed) {
+ case USB_SPEED_SUPER:
+ if (!c->superspeed)
+ continue;
+ break;
+ case USB_SPEED_HIGH:
if (!c->highspeed)
continue;
- } else {
+ break;
+ default:
if (!c->fullspeed)
continue;
}
+
if (w_value == 0)
return config_buf(c, speed, cdev->req->buf, type);
w_value--;
@@ -414,16 +469,22 @@ static int count_configs(struct usb_composite_dev *cdev, unsigned type)
struct usb_configuration *c;
unsigned count = 0;
int hs = 0;
+ int ss = 0;
if (gadget_is_dualspeed(gadget)) {
if (gadget->speed == USB_SPEED_HIGH)
hs = 1;
+ if (gadget->speed == USB_SPEED_SUPER)
+ ss = 1;
if (type == USB_DT_DEVICE_QUALIFIER)
hs = !hs;
}
list_for_each_entry(c, &cdev->configs, list) {
/* ignore configs that won't work at this speed */
- if (hs) {
+ if (ss) {
+ if (!c->superspeed)
+ continue;
+ } else if (hs) {
if (!c->highspeed)
continue;
} else {
@@ -435,6 +496,73 @@ static int count_configs(struct usb_composite_dev *cdev, unsigned type)
return count;
}
+/**
+ * bos_desc() - prepares the BOS descriptor.
+ * @cdev: pointer to usb_composite device to generate the bos
+ * descriptor for
+ *
+ * This function generates the BOS (Binary Device Object)
+ * descriptor and its device capabilities descriptors. The BOS
+ * descriptor should be supported by a SuperSpeed device.
+ */
+static int bos_desc(struct usb_composite_dev *cdev)
+{
+ struct usb_ext_cap_descriptor *usb_ext;
+ struct usb_ss_cap_descriptor *ss_cap;
+ struct usb_dcd_config_params dcd_config_params;
+ struct usb_bos_descriptor *bos = cdev->req->buf;
+
+ bos->bLength = USB_DT_BOS_SIZE;
+ bos->bDescriptorType = USB_DT_BOS;
+
+ bos->wTotalLength = cpu_to_le16(USB_DT_BOS_SIZE);
+ bos->bNumDeviceCaps = 0;
+
+ /*
+ * A SuperSpeed device shall include the USB2.0 extension descriptor
+ * and shall support LPM when operating in USB2.0 HS mode.
+ */
+ usb_ext = (struct usb_ext_cap_descriptor *)
+ (cdev->req->buf+bos->wTotalLength);
+ bos->bNumDeviceCaps++;
+ le16_add_cpu(&(bos->wTotalLength), USB_DT_USB_EXT_CAP_SIZE);
+ usb_ext->bLength = USB_DT_USB_EXT_CAP_SIZE;
+ usb_ext->bDescriptorType = USB_DT_DEVICE_CAPABILITY;
+ usb_ext->bDevCapabilityType = USB_CAP_TYPE_EXT;
+ usb_ext->bmAttributes = cpu_to_le32(USB_LPM_SUPPORT);
+
+ /*
+ * The Superspeed USB Capability descriptor shall be implemented by all
+ * SuperSpeed devices.
+ */
+ ss_cap = (struct usb_ss_cap_descriptor *)
+ (cdev->req->buf+bos->wTotalLength);
+ bos->bNumDeviceCaps++;
+ le16_add_cpu(&(bos->wTotalLength), USB_DT_USB_SS_CAP_SIZE);
+ ss_cap->bLength = USB_DT_USB_SS_CAP_SIZE;
+ ss_cap->bDescriptorType = USB_DT_DEVICE_CAPABILITY;
+ ss_cap->bDevCapabilityType = USB_SS_CAP_TYPE;
+ ss_cap->bmAttributes = 0; /* LTM is not supported yet */
+ ss_cap->wSpeedSupported = cpu_to_le16(USB_LOW_SPEED_OPERATION |
+ USB_FULL_SPEED_OPERATION |
+ USB_HIGH_SPEED_OPERATION |
+ USB_5GBPS_OPERATION);
+ ss_cap->bFunctionalitySupport = USB_LOW_SPEED_OPERATION;
+
+ /* Get Controller configuration */
+ if (cdev->gadget->ops->get_config_params)
+ cdev->gadget->ops->get_config_params(&dcd_config_params);
+ else {
+ dcd_config_params.bU1devExitLat = USB_DEFULT_U1_DEV_EXIT_LAT;
+ dcd_config_params.bU2DevExitLat =
+ cpu_to_le16(USB_DEFULT_U2_DEV_EXIT_LAT);
+ }
+ ss_cap->bU1devExitLat = dcd_config_params.bU1devExitLat;
+ ss_cap->bU2DevExitLat = dcd_config_params.bU2DevExitLat;
+
+ return bos->wTotalLength;
+}
+
static void device_qual(struct usb_composite_dev *cdev)
{
struct usb_qualifier_descriptor *qual = cdev->req->buf;
@@ -478,20 +606,26 @@ static int set_config(struct usb_composite_dev *cdev,
unsigned power = gadget_is_otg(gadget) ? 8 : 100;
int tmp;
- if (cdev->config)
- reset_config(cdev);
-
if (number) {
list_for_each_entry(c, &cdev->configs, list) {
if (c->bConfigurationValue == number) {
+ /*
+ * Need to disable the FDs of the previous
+ * configuration
+ */
+ if (cdev->config)
+ reset_config(cdev);
result = 0;
break;
}
}
if (result < 0)
goto done;
- } else
+ } else { /* Zero configuration value - need to reset the config */
+ if (cdev->config)
+ reset_config(cdev);
result = 0;
+ }
INFO(cdev, "%s speed config #%d: %s\n",
({ char *speed;
@@ -499,6 +633,9 @@ static int set_config(struct usb_composite_dev *cdev,
case USB_SPEED_LOW: speed = "low"; break;
case USB_SPEED_FULL: speed = "full"; break;
case USB_SPEED_HIGH: speed = "high"; break;
+ case USB_SPEED_SUPER:
+ speed = "super";
+ break;
default: speed = "?"; break;
} ; speed; }), number, c ? c->label : "unconfigured");
@@ -521,10 +658,16 @@ static int set_config(struct usb_composite_dev *cdev,
* function's setup callback instead of the current
* configuration's setup callback.
*/
- if (gadget->speed == USB_SPEED_HIGH)
+ switch (gadget->speed) {
+ case USB_SPEED_SUPER:
+ descriptors = f->ss_descriptors;
+ break;
+ case USB_SPEED_HIGH:
descriptors = f->hs_descriptors;
- else
+ break;
+ default:
descriptors = f->descriptors;
+ }
for (; *descriptors; ++descriptors) {
struct usb_endpoint_descriptor *ep;
@@ -617,8 +760,9 @@ int usb_add_config(struct usb_composite_dev *cdev,
} else {
unsigned i;
- DBG(cdev, "cfg %d/%p speeds:%s%s\n",
+ DBG(cdev, "cfg %d/%p speeds:%s%s%s\n",
config->bConfigurationValue, config,
+ config->superspeed ? " super" : "",
config->highspeed ? " high" : "",
config->fullspeed
? (gadget_is_dualspeed(cdev->gadget)
@@ -897,6 +1041,7 @@ composite_setup(struct usb_gadget *gadget, const struct usb_ctrlrequest *ctrl)
struct usb_composite_dev *cdev = get_gadget_data(gadget);
struct usb_request *req = cdev->req;
int value = -EOPNOTSUPP;
+ int status = 0;
u16 w_index = le16_to_cpu(ctrl->wIndex);
u8 intf = w_index & 0xFF;
u16 w_value = le16_to_cpu(ctrl->wValue);
@@ -924,18 +1069,29 @@ composite_setup(struct usb_gadget *gadget, const struct usb_ctrlrequest *ctrl)
case USB_DT_DEVICE:
cdev->desc.bNumConfigurations =
count_configs(cdev, USB_DT_DEVICE);
+ cdev->desc.bMaxPacketSize0 =
+ cdev->gadget->ep0->maxpacket;
+ if (gadget_is_superspeed(gadget)) {
+ if (gadget->speed >= USB_SPEED_SUPER)
+ cdev->desc.bcdUSB = cpu_to_le16(0x0300);
+ else
+ cdev->desc.bcdUSB = cpu_to_le16(0x0210);
+ }
+
value = min(w_length, (u16) sizeof cdev->desc);
memcpy(req->buf, &cdev->desc, value);
break;
case USB_DT_DEVICE_QUALIFIER:
- if (!gadget_is_dualspeed(gadget))
+ if (!gadget_is_dualspeed(gadget) ||
+ gadget->speed >= USB_SPEED_SUPER)
break;
device_qual(cdev);
value = min_t(int, w_length,
sizeof(struct usb_qualifier_descriptor));
break;
case USB_DT_OTHER_SPEED_CONFIG:
- if (!gadget_is_dualspeed(gadget))
+ if (!gadget_is_dualspeed(gadget) ||
+ gadget->speed >= USB_SPEED_SUPER)
break;
/* FALLTHROUGH */
case USB_DT_CONFIG:
@@ -949,6 +1105,12 @@ composite_setup(struct usb_gadget *gadget, const struct usb_ctrlrequest *ctrl)
if (value >= 0)
value = min(w_length, (u16) value);
break;
+ case USB_DT_BOS:
+ if (gadget_is_superspeed(gadget)) {
+ value = bos_desc(cdev);
+ value = min(w_length, (u16) value);
+ }
+ break;
}
break;
@@ -1016,6 +1178,62 @@ composite_setup(struct usb_gadget *gadget, const struct usb_ctrlrequest *ctrl)
*((u8 *)req->buf) = value;
value = min(w_length, (u16) 1);
break;
+
+ /*
+ * USB 3.0 additions:
+ * Function driver should handle get_status request. If such cb
+ * wasn't supplied we respond with default value = 0
+ * Note: function driver should supply such cb only for the first
+ * interface of the function
+ */
+ case USB_REQ_GET_STATUS:
+ if (!gadget_is_superspeed(gadget))
+ goto unknown;
+ if (ctrl->bRequestType != (USB_DIR_IN | USB_RECIP_INTERFACE))
+ goto unknown;
+ value = 2; /* This is the length of the get_status reply */
+ *((__le16 *)req->buf) = 0;
+ if (!cdev->config || intf >= MAX_CONFIG_INTERFACES)
+ break;
+ f = cdev->config->interface[intf];
+ if (!f)
+ break;
+ status = f->get_status ? f->get_status(f) : 0;
+ if (status < 0)
+ break;
+ *((__le16 *)req->buf) = cpu_to_le16(status & 0x0000ffff);
+ break;
+ /*
+ * Function drivers should handle SetFeature/ClearFeature
+ * (FUNCTION_SUSPEND) request. function_suspend cb should be supplied
+ * only for the first interface of the function
+ */
+ case USB_REQ_CLEAR_FEATURE:
+ case USB_REQ_SET_FEATURE:
+ if (!gadget_is_superspeed(gadget))
+ goto unknown;
+ if (ctrl->bRequestType != (USB_DIR_OUT | USB_RECIP_INTERFACE))
+ goto unknown;
+ switch (w_value) {
+ case USB_INTRF_FUNC_SUSPEND:
+ if (!cdev->config || intf >= MAX_CONFIG_INTERFACES)
+ break;
+ f = cdev->config->interface[intf];
+ if (!f)
+ break;
+ value = 0;
+ if (f->func_suspend)
+ value = f->func_suspend(f, w_index >> 8);
+ if (value < 0) {
+ ERROR(cdev, "func_suspend() returned "
+ "error %d\n", value);
+ value = 0;
+ }
+ break;
+ default:
+ break;
+ }
+ break;
default:
unknown:
VDBG(cdev,
@@ -1379,6 +1597,9 @@ int usb_composite_probe(struct usb_composite_driver *driver,
driver->iProduct = driver->name;
composite_driver.function = (char *) driver->name;
composite_driver.driver.name = driver->name;
+#ifdef CONFIG_USB_GADGET_SUPERSPEED
+ composite_driver.speed = USB_SPEED_SUPER;
+#endif /* CONFIG_USB_GADGET_SUPERSPEED */
composite = driver;
composite_gadget_bind = bind;
diff --git a/drivers/usb/gadget/epautoconf.c b/drivers/usb/gadget/epautoconf.c
index 0022d44..b9e0b6d 100644
--- a/drivers/usb/gadget/epautoconf.c
+++ b/drivers/usb/gadget/epautoconf.c
@@ -142,13 +142,13 @@ ep_matches (
max = 0x7ff & le16_to_cpu(desc->wMaxPacketSize);
switch (type) {
case USB_ENDPOINT_XFER_INT:
- /* INT: limit 64 bytes full speed, 1024 high speed */
+ /* INT: limit 64 bytes full speed, 1024 high/super speed */
if (!gadget->is_dualspeed && max > 64)
return 0;
/* FALLTHROUGH */
case USB_ENDPOINT_XFER_ISOC:
- /* ISO: limit 1023 bytes full speed, 1024 high speed */
+ /* ISO: limit 1023 bytes full speed, 1024 high/super speed */
if (ep->maxpacket < max)
return 0;
if (!gadget->is_dualspeed && max > 1023)
@@ -183,7 +183,8 @@ ep_matches (
}
/* report (variable) full speed bulk maxpacket */
- if (USB_ENDPOINT_XFER_BULK == type) {
+ if ((USB_ENDPOINT_XFER_BULK == type)
+ && (gadget->speed < USB_SPEED_HIGH)) {
int size = ep->maxpacket;
/* min() doesn't work on bitfields with gcc-3.5 */
diff --git a/include/linux/usb/ch9.h b/include/linux/usb/ch9.h
index 0fd3fbd..7654b64 100644
--- a/include/linux/usb/ch9.h
+++ b/include/linux/usb/ch9.h
@@ -142,8 +142,6 @@
#define USB_DEVICE_LTM_ENABLE 50 /* dev may send LTM */
#define USB_INTRF_FUNC_SUSPEND 0 /* function suspend */
-#define USB_INTR_FUNC_SUSPEND_OPT_MASK 0xFF00
-
#define USB_ENDPOINT_HALT 0 /* IN/OUT will STALL */
/* Bit array elements as returned by the USB_REQ_GET_STATUS request. */
diff --git a/include/linux/usb/composite.h b/include/linux/usb/composite.h
index 5564d5e..511bc2a 100644
--- a/include/linux/usb/composite.h
+++ b/include/linux/usb/composite.h
@@ -59,6 +59,12 @@ struct usb_configuration;
* @hs_descriptors: Table of high speed descriptors, using interface and
* string identifiers assigned during @bind(). If this pointer is null,
* the function will not be available at high speed.
+ * @ss_descriptors: Table of super speed descriptors. If
+ * wasnt supplied by the FD during @bind() and
+ * !ss_not_capble, will be generated automaticly with
+ * default values while working in superspeed mode. If this
+ * pointer is null after initiation, the function will not
+ * be available at super speed.
* @config: assigned when @usb_add_function() is called; this is the
* configuration with which this function is associated.
* @bind: Before the gadget can register, all of its functions bind() to the
@@ -77,6 +83,10 @@ struct usb_configuration;
* @setup: Used for interface-specific control requests.
* @suspend: Notifies functions when the host stops sending USB traffic.
* @resume: Notifies functions when the host restarts USB traffic.
+ * @get_status: Returns function status as a reply to
+ * GetStatus() request when the recepient is Interface.
+ * @func_suspend: callback to be called when
+ * SetFeature(FUNCTION_SUSPEND) is reseived
*
* A single USB function uses one or more interfaces, and should in most
* cases support operation at both full and high speeds. Each function is
@@ -106,6 +116,7 @@ struct usb_function {
struct usb_gadget_strings **strings;
struct usb_descriptor_header **descriptors;
struct usb_descriptor_header **hs_descriptors;
+ struct usb_descriptor_header **ss_descriptors;
struct usb_configuration *config;
@@ -132,6 +143,10 @@ struct usb_function {
void (*suspend)(struct usb_function *);
void (*resume)(struct usb_function *);
+ /* USB 3.0 additions */
+ int (*get_status)(struct usb_function *);
+ int (*func_suspend)(struct usb_function *,
+ u8 suspend_opt);
/* private: */
/* internals */
struct list_head list;
@@ -237,6 +252,7 @@ struct usb_configuration {
struct list_head list;
struct list_head functions;
u8 next_interface_id;
+ unsigned superspeed:1;
unsigned highspeed:1;
unsigned fullspeed:1;
struct usb_function *interface[MAX_CONFIG_INTERFACES];
diff --git a/include/linux/usb/gadget.h b/include/linux/usb/gadget.h
index 318c815..d1b4ee8 100644
--- a/include/linux/usb/gadget.h
+++ b/include/linux/usb/gadget.h
@@ -131,11 +131,15 @@ struct usb_ep_ops {
* @maxpacket:The maximum packet size used on this endpoint. The initial
* value can sometimes be reduced (hardware allowing), according to
* the endpoint descriptor used to configure the endpoint.
+ * @mult: multiplier, 'mult' value for SS Isoc EPs
+ * @maxburst: the maximum number of bursts supported by this EP (for usb3)
* @driver_data:for use by the gadget driver.
* @address: used to identify the endpoint when finding descriptor that
* matches connection speed
* @desc: endpoint descriptor. This pointer is set before the endpoint is
* enabled and remains valid until the endpoint is disabled.
+ * @comp_desc: In case of SuperSpeed support, this is the endpoint companion
+ * descriptor that is used to configure the endpoint
*
* the bus controller driver lists all the general purpose endpoints in
* gadget->ep_list. the control endpoint (gadget->ep0) is not in that list,
@@ -148,8 +152,12 @@ struct usb_ep {
const struct usb_ep_ops *ops;
struct list_head ep_list;
unsigned maxpacket:16;
+ unsigned mult:2;
+ unsigned pad:1;
+ unsigned maxburst:4;
u8 address;
const struct usb_endpoint_descriptor *desc;
+ const struct usb_ss_ep_comp_descriptor *comp_desc;
};
/*-------------------------------------------------------------------------*/
@@ -417,6 +425,14 @@ static inline void usb_ep_fifo_flush(struct usb_ep *ep)
/*-------------------------------------------------------------------------*/
+struct usb_dcd_config_params {
+ __u8 bU1devExitLat; /* U1 Device exit Latency */
+#define USB_DEFULT_U1_DEV_EXIT_LAT 0x01 /* Less then 1 microsec */
+ __le16 bU2DevExitLat; /* U2 Device exit Latency */
+#define USB_DEFULT_U2_DEV_EXIT_LAT 0x1F4 /* Less then 500 microsec */
+};
+
+
struct usb_gadget;
/* the rest of the api to the controller hardware: device operations,
@@ -431,6 +447,7 @@ struct usb_gadget_ops {
int (*pullup) (struct usb_gadget *, int is_on);
int (*ioctl)(struct usb_gadget *,
unsigned code, unsigned long param);
+ void (*get_config_params)(struct usb_dcd_config_params *);
};
/**
@@ -522,6 +539,23 @@ static inline int gadget_is_dualspeed(struct usb_gadget *g)
}
/**
+ * gadget_is_superspeed() - return true if the hardware handles
+ * supperspeed
+ * @g: controller that might support supper speed
+ */
+static inline int gadget_is_superspeed(struct usb_gadget *g)
+{
+#ifdef CONFIG_USB_GADGET_SUPERSPEED
+ /* runtime test would check "g->is_superspeed" ... that might be
+ * useful to work around hardware bugs, but is mostly pointless
+ */
+ return 1;
+#else
+ return 0;
+#endif
+}
+
+/**
* gadget_is_otg - return true iff the hardware is OTG-ready
* @g: controller that might have a Mini-AB connector
*
--
1.7.3.3
--
Sent by an employee of the Qualcomm Innovation Center, Inc.
The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum.
^ permalink raw reply related [flat|nested] 13+ messages in thread* Re: [PATCH v11 4/7] usb:gadget: Add SuperSpeed support to the Gadget Framework
2011-05-19 11:43 ` [PATCH v11 4/7] usb:gadget: Add SuperSpeed support to the Gadget Framework Tatyana Brokhman
@ 2011-05-20 16:49 ` Sebastian Andrzej Siewior
2011-05-22 7:20 ` Tanya Brokhman
0 siblings, 1 reply; 13+ messages in thread
From: Sebastian Andrzej Siewior @ 2011-05-20 16:49 UTC (permalink / raw)
To: Tatyana Brokhman; +Cc: greg, linux-usb, balbi, ablay, linux-arm-msm, open list
* Tatyana Brokhman | 2011-05-19 14:43:29 [+0300]:
>diff --git a/drivers/usb/gadget/composite.c b/drivers/usb/gadget/composite.c
>index cfba1ee..bd811ac 100644
>--- a/drivers/usb/gadget/composite.c
>+++ b/drivers/usb/gadget/composite.c
>@@ -136,6 +139,13 @@ int config_ep_by_speed(struct usb_gadget *g,
>
> /* select desired speed */
> switch (g->speed) {
>+ case USB_SPEED_SUPER:
>+ if (gadget_is_superspeed(g)) {
>+ speed_desc = f->ss_descriptors;
>+ want_comp_desc = 1;
>+ break;
>+ }
>+ /* else: Fall trough */
> case USB_SPEED_HIGH:
> if (gadget_is_dualspeed(g)) {
> speed_desc = f->hs_descriptors;
>@@ -157,7 +167,35 @@ ep_found:
> /* commit results */
> _ep->maxpacket = le16_to_cpu(chosen_desc->wMaxPacketSize);
> _ep->desc = chosen_desc;
>-
>+ _ep->comp_desc = NULL;
>+ _ep->maxburst = 0;
>+ _ep->mult = 0;
>+ if (want_comp_desc) {
if (!want_comp_desc)
return 0;
I have one ident level less :)
>+ /*
>+ * Companion descriptor should follow EP descriptor
>+ * USB 3.0 spec, #9.6.7
>+ */
>+ comp_desc = (struct usb_ss_ep_comp_descriptor *)*(++d_spd);
>+ if (!comp_desc ||
>+ (comp_desc->bDescriptorType != USB_DT_SS_ENDPOINT_COMP))
>+ return -EIO;
>+ _ep->comp_desc = comp_desc;
>+ if (g->speed == USB_SPEED_SUPER) {
>+ switch (usb_endpoint_type(_ep->desc)) {
>+ case USB_ENDPOINT_XFER_BULK:
>+ case USB_ENDPOINT_XFER_INT:
>+ _ep->maxburst = comp_desc->bMaxBurst;
>+ break;
>+ case USB_ENDPOINT_XFER_ISOC:
>+ /* mult: bits 1:0 of bmAttributes */
>+ _ep->mult = comp_desc->bmAttributes & 0x3;
>+ break;
>+ default:
>+ /* Do nothing for control endpoints */
>+ break;
>+ }
>+ }
>+ }
> return 0;
> }
>
>@@ -435,6 +496,73 @@ static int count_configs(struct usb_composite_dev *cdev, unsigned type)
> return count;
> }
>
>+/**
>+ * bos_desc() - prepares the BOS descriptor.
>+ * @cdev: pointer to usb_composite device to generate the bos
>+ * descriptor for
>+ *
>+ * This function generates the BOS (Binary Device Object)
>+ * descriptor and its device capabilities descriptors. The BOS
>+ * descriptor should be supported by a SuperSpeed device.
>+ */
>+static int bos_desc(struct usb_composite_dev *cdev)
>+{
>+ struct usb_ext_cap_descriptor *usb_ext;
>+ struct usb_ss_cap_descriptor *ss_cap;
>+ struct usb_dcd_config_params dcd_config_params;
>+ struct usb_bos_descriptor *bos = cdev->req->buf;
>+
>+ bos->bLength = USB_DT_BOS_SIZE;
>+ bos->bDescriptorType = USB_DT_BOS;
>+
>+ bos->wTotalLength = cpu_to_le16(USB_DT_BOS_SIZE);
>+ bos->bNumDeviceCaps = 0;
>+
>+ /*
>+ * A SuperSpeed device shall include the USB2.0 extension descriptor
>+ * and shall support LPM when operating in USB2.0 HS mode.
>+ */
>+ usb_ext = (struct usb_ext_cap_descriptor *)
cdev->req->buf is (void *) so you can skip that cast.
>+ (cdev->req->buf+bos->wTotalLength);
a space between + please. bos->wTotalLength is le16 so you can't simply
do that way.
What about something like
usb_ext = (struct usb_ext_cap_descriptor *)(bos + 1)
?
>+ bos->bNumDeviceCaps++;
>+ le16_add_cpu(&(bos->wTotalLength), USB_DT_USB_EXT_CAP_SIZE);
the () around bos->wTotalLength aren't required.
>+ usb_ext->bLength = USB_DT_USB_EXT_CAP_SIZE;
>+ usb_ext->bDescriptorType = USB_DT_DEVICE_CAPABILITY;
>+ usb_ext->bDevCapabilityType = USB_CAP_TYPE_EXT;
>+ usb_ext->bmAttributes = cpu_to_le32(USB_LPM_SUPPORT);
>+
>+ /*
>+ * The Superspeed USB Capability descriptor shall be implemented by all
>+ * SuperSpeed devices.
>+ */
>+ ss_cap = (struct usb_ss_cap_descriptor *)
>+ (cdev->req->buf+bos->wTotalLength);
Same here.
>+ bos->bNumDeviceCaps++;
>+ le16_add_cpu(&(bos->wTotalLength), USB_DT_USB_SS_CAP_SIZE);
and here.
>+ ss_cap->bLength = USB_DT_USB_SS_CAP_SIZE;
>+ ss_cap->bDescriptorType = USB_DT_DEVICE_CAPABILITY;
>+ ss_cap->bDevCapabilityType = USB_SS_CAP_TYPE;
>+ ss_cap->bmAttributes = 0; /* LTM is not supported yet */
>+ ss_cap->wSpeedSupported = cpu_to_le16(USB_LOW_SPEED_OPERATION |
>+ USB_FULL_SPEED_OPERATION |
>+ USB_HIGH_SPEED_OPERATION |
>+ USB_5GBPS_OPERATION);
>+ ss_cap->bFunctionalitySupport = USB_LOW_SPEED_OPERATION;
>+
>+ /* Get Controller configuration */
>+ if (cdev->gadget->ops->get_config_params)
>+ cdev->gadget->ops->get_config_params(&dcd_config_params);
>+ else {
>+ dcd_config_params.bU1devExitLat = USB_DEFULT_U1_DEV_EXIT_LAT;
>+ dcd_config_params.bU2DevExitLat =
>+ cpu_to_le16(USB_DEFULT_U2_DEV_EXIT_LAT);
>+ }
>+ ss_cap->bU1devExitLat = dcd_config_params.bU1devExitLat;
>+ ss_cap->bU2DevExitLat = dcd_config_params.bU2DevExitLat;
>+
>+ return bos->wTotalLength;
return le16_to_cpu(bos->wTotalLength);
>+}
>+
> static void device_qual(struct usb_composite_dev *cdev)
> {
> struct usb_qualifier_descriptor *qual = cdev->req->buf;
>@@ -478,20 +606,26 @@ static int set_config(struct usb_composite_dev *cdev,
> unsigned power = gadget_is_otg(gadget) ? 8 : 100;
> int tmp;
>
>- if (cdev->config)
>- reset_config(cdev);
>-
> if (number) {
> list_for_each_entry(c, &cdev->configs, list) {
> if (c->bConfigurationValue == number) {
>+ /*
>+ * Need to disable the FDs of the previous
>+ * configuration
>+ */
The comment is kind of obvious :) You are changing the behavioud here:
The old code removed the current configuration if the new one was not
available while the new one does not. According to ch9.4.7 that is the
right thing to do. So you might add something of this to the comment :)
>+ if (cdev->config)
>+ reset_config(cdev);
> result = 0;
> break;
> }
> }
> if (result < 0)
> goto done;
>- } else
>+ } else { /* Zero configuration value - need to reset the config */
>+ if (cdev->config)
>+ reset_config(cdev);
> result = 0;
>+ }
>
> INFO(cdev, "%s speed config #%d: %s\n",
> ({ char *speed;
>@@ -499,6 +633,9 @@ static int set_config(struct usb_composite_dev *cdev,
> case USB_SPEED_LOW: speed = "low"; break;
> case USB_SPEED_FULL: speed = "full"; break;
> case USB_SPEED_HIGH: speed = "high"; break;
>+ case USB_SPEED_SUPER:
>+ speed = "super";
>+ break;
This is not my favorite style either but please do it the way the other
three are done.
> default: speed = "?"; break;
> } ; speed; }), number, c ? c->label : "unconfigured");
>
Sebastian
^ permalink raw reply [flat|nested] 13+ messages in thread* RE: [PATCH v11 4/7] usb:gadget: Add SuperSpeed support to the Gadget Framework
2011-05-20 16:49 ` Sebastian Andrzej Siewior
@ 2011-05-22 7:20 ` Tanya Brokhman
2011-05-22 10:59 ` Sebastian Andrzej Siewior
0 siblings, 1 reply; 13+ messages in thread
From: Tanya Brokhman @ 2011-05-22 7:20 UTC (permalink / raw)
To: 'Sebastian Andrzej Siewior'
Cc: greg, linux-usb, balbi, ablay, linux-arm-msm, 'open list'
Hi Sebastian
> >@@ -157,7 +167,35 @@ ep_found:
> > /* commit results */
> > _ep->maxpacket = le16_to_cpu(chosen_desc->wMaxPacketSize);
> > _ep->desc = chosen_desc;
> >-
> >+ _ep->comp_desc = NULL;
> >+ _ep->maxburst = 0;
> >+ _ep->mult = 0;
> >+ if (want_comp_desc) {
>
> if (!want_comp_desc)
> return 0;
>
> I have one ident level less :)
Done :)
> >+/**
> >+ * bos_desc() - prepares the BOS descriptor.
> >+ * @cdev: pointer to usb_composite device to generate the bos
> >+ * descriptor for
> >+ *
> >+ * This function generates the BOS (Binary Device Object)
> >+ * descriptor and its device capabilities descriptors. The BOS
> >+ * descriptor should be supported by a SuperSpeed device.
> >+ */
> >+static int bos_desc(struct usb_composite_dev *cdev)
> >+{
> >+ struct usb_ext_cap_descriptor *usb_ext;
> >+ struct usb_ss_cap_descriptor *ss_cap;
> >+ struct usb_dcd_config_params dcd_config_params;
> >+ struct usb_bos_descriptor *bos = cdev->req->buf;
> >+
> >+ bos->bLength = USB_DT_BOS_SIZE;
> >+ bos->bDescriptorType = USB_DT_BOS;
> >+
> >+ bos->wTotalLength = cpu_to_le16(USB_DT_BOS_SIZE);
> >+ bos->bNumDeviceCaps = 0;
> >+
> >+ /*
> >+ * A SuperSpeed device shall include the USB2.0 extension
> descriptor
> >+ * and shall support LPM when operating in USB2.0 HS mode.
> >+ */
> >+ usb_ext = (struct usb_ext_cap_descriptor *)
> cdev->req->buf is (void *) so you can skip that cast.
>
> >+ (cdev->req->buf+bos->wTotalLength);
> a space between + please. bos->wTotalLength is le16 so you can't simply
> do that way.
>
> What about something like
>
> usb_ext = (struct usb_ext_cap_descriptor *)(bos + 1)
>
> ?
Added the spaces and the le16_to_cpu(bos->wTotalLength).
It seems clearer to me to leave it as
usb_ext = cdev->req->buf + le16_to_cpu(bos->wTotalLength);
if that's ok with you.
> >@@ -499,6 +633,9 @@ static int set_config(struct usb_composite_dev
> *cdev,
> > case USB_SPEED_LOW: speed = "low"; break;
> > case USB_SPEED_FULL: speed = "full"; break;
> > case USB_SPEED_HIGH: speed = "high"; break;
> >+ case USB_SPEED_SUPER:
> >+ speed = "super";
> >+ break;
>
> This is not my favorite style either but please do it the way the other
> three are done.
Well here is the dilemma: if I do it the other tree were done - I get
checkpatch error.
You're right, adding this the way it's above doesn't look too good but when
I fixed the other three I was asked not to do so in this patch, which also
makes sense since it has nothing to do with SS support...
So what do I do? Submit with a checkpatch error?
Best regards,
Tanya Brokhman
Consultant for Qualcomm Innovation Center, Inc.
Qualcomm Innovation Center, Inc. is a member of Code Aurora Forum
^ permalink raw reply [flat|nested] 13+ messages in thread* Re: [PATCH v11 4/7] usb:gadget: Add SuperSpeed support to the Gadget Framework
2011-05-22 7:20 ` Tanya Brokhman
@ 2011-05-22 10:59 ` Sebastian Andrzej Siewior
2011-05-23 6:19 ` Felipe Balbi
0 siblings, 1 reply; 13+ messages in thread
From: Sebastian Andrzej Siewior @ 2011-05-22 10:59 UTC (permalink / raw)
To: Tanya Brokhman
Cc: greg, linux-usb, balbi, ablay, linux-arm-msm, 'open list'
* Tanya Brokhman | 2011-05-22 10:20:42 [+0300]:
>Hi Sebastian
Hi Tanya,
>> >+ usb_ext = (struct usb_ext_cap_descriptor *)
>> cdev->req->buf is (void *) so you can skip that cast.
>>
>> >+ (cdev->req->buf+bos->wTotalLength);
>> a space between + please. bos->wTotalLength is le16 so you can't simply
>> do that way.
>>
>> What about something like
>>
>> usb_ext = (struct usb_ext_cap_descriptor *)(bos + 1)
>>
>> ?
>
>Added the spaces and the le16_to_cpu(bos->wTotalLength).
>It seems clearer to me to leave it as
> usb_ext = cdev->req->buf + le16_to_cpu(bos->wTotalLength);
>if that's ok with you.
Yes it is.
>
>> >@@ -499,6 +633,9 @@ static int set_config(struct usb_composite_dev
>> *cdev,
>> > case USB_SPEED_LOW: speed = "low"; break;
>> > case USB_SPEED_FULL: speed = "full"; break;
>> > case USB_SPEED_HIGH: speed = "high"; break;
>> >+ case USB_SPEED_SUPER:
>> >+ speed = "super";
>> >+ break;
>>
>> This is not my favorite style either but please do it the way the other
>> three are done.
>
>Well here is the dilemma: if I do it the other tree were done - I get
>checkpatch error.
>You're right, adding this the way it's above doesn't look too good but when
>I fixed the other three I was asked not to do so in this patch, which also
>makes sense since it has nothing to do with SS support...
>So what do I do? Submit with a checkpatch error?
It is nice to have things consistent and a follow-up patch could fix the
checkpatch error(s).
>
>
Sebastian
^ permalink raw reply [flat|nested] 13+ messages in thread
* Re: [PATCH v11 4/7] usb:gadget: Add SuperSpeed support to the Gadget Framework
2011-05-22 10:59 ` Sebastian Andrzej Siewior
@ 2011-05-23 6:19 ` Felipe Balbi
0 siblings, 0 replies; 13+ messages in thread
From: Felipe Balbi @ 2011-05-23 6:19 UTC (permalink / raw)
To: Sebastian Andrzej Siewior
Cc: Tanya Brokhman, greg, linux-usb, balbi, ablay, linux-arm-msm,
'open list'
[-- Attachment #1: Type: text/plain, Size: 633 bytes --]
Hi,
On Sun, May 22, 2011 at 12:59:08PM +0200, Sebastian Andrzej Siewior wrote:
> >Well here is the dilemma: if I do it the other tree were done - I get
> >checkpatch error.
> >You're right, adding this the way it's above doesn't look too good but when
> >I fixed the other three I was asked not to do so in this patch, which also
> >makes sense since it has nothing to do with SS support...
> >So what do I do? Submit with a checkpatch error?
>
> It is nice to have things consistent and a follow-up patch could fix the
> checkpatch error(s).
I tend to like more when the cleanup comes beforehand ;-)
--
balbi
[-- Attachment #2: Digital signature --]
[-- Type: application/pgp-signature, Size: 490 bytes --]
^ permalink raw reply [flat|nested] 13+ messages in thread
* [PATCH/RESEND v11 5/7] usb: Add streams support to the gadget framework
[not found] <1305805417-31750-1-git-send-email-tlinder@codeaurora.org>
` (3 preceding siblings ...)
2011-05-19 11:43 ` [PATCH v11 4/7] usb:gadget: Add SuperSpeed support to the Gadget Framework Tatyana Brokhman
@ 2011-05-19 11:43 ` Tatyana Brokhman
2011-05-19 11:43 ` [PATCH v11 6/7] usb:dummy_hcd: use the shared_hcd infrustructure Tatyana Brokhman
2011-05-19 11:43 ` [PATCH v11 7/7] usb: Adding SuperSpeed support to dummy_hcd Tatyana Brokhman
6 siblings, 0 replies; 13+ messages in thread
From: Tatyana Brokhman @ 2011-05-19 11:43 UTC (permalink / raw)
To: greg
Cc: linux-usb, balbi, ablay, linux-arm-msm, Tatyana Brokhman,
Maya Erez, open list
This patch defines necessary fields to support streaming for USB3.0.
It implements a new function (usb_ep_autoconfig_ss) to be used instead of
the existing usb_ep_autoconfig when working in SS mode and there is a
need to search for an endpoint according to the number of required
streams.
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Tatyana Brokhman <tlinder@codeaurora.org>
---
drivers/usb/gadget/epautoconf.c | 125 +++++++++++++++++++++++++++++++--------
include/linux/usb/gadget.h | 10 +++
2 files changed, 110 insertions(+), 25 deletions(-)
diff --git a/drivers/usb/gadget/epautoconf.c b/drivers/usb/gadget/epautoconf.c
index b9e0b6d..7aa2ed0 100644
--- a/drivers/usb/gadget/epautoconf.c
+++ b/drivers/usb/gadget/epautoconf.c
@@ -63,13 +63,16 @@ static int
ep_matches (
struct usb_gadget *gadget,
struct usb_ep *ep,
- struct usb_endpoint_descriptor *desc
+ struct usb_endpoint_descriptor *desc,
+ struct usb_ss_ep_comp_descriptor *ep_comp
)
{
u8 type;
const char *tmp;
u16 max;
+ int num_req_streams = 0;
+
/* endpoint already claimed? */
if (NULL != ep->driver_data)
return 0;
@@ -129,6 +132,22 @@ ep_matches (
}
/*
+ * Get the number of required streams from the EP companion
+ * descriptor and see if the EP matches it
+ */
+ if (usb_endpoint_xfer_bulk(desc)) {
+ if (ep_comp) {
+ num_req_streams = ep_comp->bmAttributes & 0x1f;
+ if (num_req_streams > ep->max_streams)
+ return 0;
+ /* Update the ep_comp descriptor if needed */
+ if (num_req_streams != ep->max_streams)
+ ep_comp->bmAttributes = ep->max_streams;
+ }
+
+ }
+
+ /*
* If the protocol driver hasn't yet decided on wMaxPacketSize
* and wants to know the maximum possible, provide the info.
*/
@@ -209,38 +228,53 @@ find_ep (struct usb_gadget *gadget, const char *name)
}
/**
- * usb_ep_autoconfig - choose an endpoint matching the descriptor
+ * usb_ep_autoconfig_ss() - choose an endpoint matching the ep
+ * descriptor and ep companion descriptor
* @gadget: The device to which the endpoint must belong.
* @desc: Endpoint descriptor, with endpoint direction and transfer mode
- * initialized. For periodic transfers, the maximum packet
- * size must also be initialized. This is modified on success.
+ * initialized. For periodic transfers, the maximum packet
+ * size must also be initialized. This is modified on
+ * success.
+ * @ep_comp: Endpoint companion descriptor, with the required
+ * number of streams. Will be modified when the chosen EP
+ * supports a different number of streams.
*
- * By choosing an endpoint to use with the specified descriptor, this
- * routine simplifies writing gadget drivers that work with multiple
- * USB device controllers. The endpoint would be passed later to
- * usb_ep_enable(), along with some descriptor.
+ * This routine replaces the usb_ep_autoconfig when needed
+ * superspeed enhancments. If such enhancemnets are required,
+ * the FD should call usb_ep_autoconfig_ss directly and provide
+ * the additional ep_comp parameter.
+ *
+ * By choosing an endpoint to use with the specified descriptor,
+ * this routine simplifies writing gadget drivers that work with
+ * multiple USB device controllers. The endpoint would be
+ * passed later to usb_ep_enable(), along with some descriptor.
*
* That second descriptor won't always be the same as the first one.
* For example, isochronous endpoints can be autoconfigured for high
* bandwidth, and then used in several lower bandwidth altsettings.
* Also, high and full speed descriptors will be different.
*
- * Be sure to examine and test the results of autoconfiguration on your
- * hardware. This code may not make the best choices about how to use the
- * USB controller, and it can't know all the restrictions that may apply.
- * Some combinations of driver and hardware won't be able to autoconfigure.
+ * Be sure to examine and test the results of autoconfiguration
+ * on your hardware. This code may not make the best choices
+ * about how to use the USB controller, and it can't know all
+ * the restrictions that may apply. Some combinations of driver
+ * and hardware won't be able to autoconfigure.
*
* On success, this returns an un-claimed usb_ep, and modifies the endpoint
* descriptor bEndpointAddress. For bulk endpoints, the wMaxPacket value
- * is initialized as if the endpoint were used at full speed. To prevent
- * the endpoint from being returned by a later autoconfig call, claim it
- * by assigning ep->driver_data to some non-null value.
+ * is initialized as if the endpoint were used at full speed and
+ * the bmAttribute field in the ep companion descriptor is
+ * updated with the assigned number of streams if it is
+ * different from the original value. To prevent the endpoint
+ * from being returned by a later autoconfig call, claim it by
+ * assigning ep->driver_data to some non-null value.
*
* On failure, this returns a null endpoint descriptor.
*/
-struct usb_ep *usb_ep_autoconfig (
+struct usb_ep *usb_ep_autoconfig_ss(
struct usb_gadget *gadget,
- struct usb_endpoint_descriptor *desc
+ struct usb_endpoint_descriptor *desc,
+ struct usb_ss_ep_comp_descriptor *ep_comp
)
{
struct usb_ep *ep;
@@ -254,23 +288,24 @@ struct usb_ep *usb_ep_autoconfig (
if (gadget_is_net2280 (gadget) && type == USB_ENDPOINT_XFER_INT) {
/* ep-e, ep-f are PIO with only 64 byte fifos */
ep = find_ep (gadget, "ep-e");
- if (ep && ep_matches (gadget, ep, desc))
+ if (ep && ep_matches(gadget, ep, desc, ep_comp))
return ep;
ep = find_ep (gadget, "ep-f");
- if (ep && ep_matches (gadget, ep, desc))
+ if (ep && ep_matches(gadget, ep, desc, ep_comp))
return ep;
} else if (gadget_is_goku (gadget)) {
if (USB_ENDPOINT_XFER_INT == type) {
/* single buffering is enough */
- ep = find_ep (gadget, "ep3-bulk");
- if (ep && ep_matches (gadget, ep, desc))
+ ep = find_ep(gadget, "ep3-bulk");
+ if (ep && ep_matches(gadget, ep, desc, ep_comp))
return ep;
} else if (USB_ENDPOINT_XFER_BULK == type
&& (USB_DIR_IN & desc->bEndpointAddress)) {
/* DMA may be available */
- ep = find_ep (gadget, "ep2-bulk");
- if (ep && ep_matches (gadget, ep, desc))
+ ep = find_ep(gadget, "ep2-bulk");
+ if (ep && ep_matches(gadget, ep, desc,
+ ep_comp))
return ep;
}
@@ -289,14 +324,14 @@ struct usb_ep *usb_ep_autoconfig (
ep = find_ep(gadget, "ep2out");
} else
ep = NULL;
- if (ep && ep_matches (gadget, ep, desc))
+ if (ep && ep_matches(gadget, ep, desc, ep_comp))
return ep;
#endif
}
/* Second, look at endpoints until an unclaimed one looks usable */
list_for_each_entry (ep, &gadget->ep_list, ep_list) {
- if (ep_matches (gadget, ep, desc))
+ if (ep_matches(gadget, ep, desc, ep_comp))
return ep;
}
@@ -305,6 +340,46 @@ struct usb_ep *usb_ep_autoconfig (
}
/**
+ * usb_ep_autoconfig() - choose an endpoint matching the
+ * descriptor
+ * @gadget: The device to which the endpoint must belong.
+ * @desc: Endpoint descriptor, with endpoint direction and transfer mode
+ * initialized. For periodic transfers, the maximum packet
+ * size must also be initialized. This is modified on success.
+ *
+ * By choosing an endpoint to use with the specified descriptor, this
+ * routine simplifies writing gadget drivers that work with multiple
+ * USB device controllers. The endpoint would be passed later to
+ * usb_ep_enable(), along with some descriptor.
+ *
+ * That second descriptor won't always be the same as the first one.
+ * For example, isochronous endpoints can be autoconfigured for high
+ * bandwidth, and then used in several lower bandwidth altsettings.
+ * Also, high and full speed descriptors will be different.
+ *
+ * Be sure to examine and test the results of autoconfiguration on your
+ * hardware. This code may not make the best choices about how to use the
+ * USB controller, and it can't know all the restrictions that may apply.
+ * Some combinations of driver and hardware won't be able to autoconfigure.
+ *
+ * On success, this returns an un-claimed usb_ep, and modifies the endpoint
+ * descriptor bEndpointAddress. For bulk endpoints, the wMaxPacket value
+ * is initialized as if the endpoint were used at full speed. To prevent
+ * the endpoint from being returned by a later autoconfig call, claim it
+ * by assigning ep->driver_data to some non-null value.
+ *
+ * On failure, this returns a null endpoint descriptor.
+ */
+struct usb_ep *usb_ep_autoconfig(
+ struct usb_gadget *gadget,
+ struct usb_endpoint_descriptor *desc
+)
+{
+ return usb_ep_autoconfig_ss(gadget, desc, NULL);
+}
+
+
+/**
* usb_ep_autoconfig_reset - reset endpoint autoconfig state
* @gadget: device for which autoconfig state will be reset
*
diff --git a/include/linux/usb/gadget.h b/include/linux/usb/gadget.h
index d1b4ee8..490fa77 100644
--- a/include/linux/usb/gadget.h
+++ b/include/linux/usb/gadget.h
@@ -27,6 +27,7 @@ struct usb_ep;
* field, and the usb controller needs one, it is responsible
* for mapping and unmapping the buffer.
* @length: Length of that data
+ * @stream_id: The stream id, when USB3.0 bulk streams are being used
* @no_interrupt: If true, hints that no completion irq is needed.
* Helpful sometimes with deep request queues that are handled
* directly by DMA controllers.
@@ -81,6 +82,7 @@ struct usb_request {
unsigned length;
dma_addr_t dma;
+ unsigned stream_id:16;
unsigned no_interrupt:1;
unsigned zero:1;
unsigned short_not_ok:1;
@@ -131,6 +133,8 @@ struct usb_ep_ops {
* @maxpacket:The maximum packet size used on this endpoint. The initial
* value can sometimes be reduced (hardware allowing), according to
* the endpoint descriptor used to configure the endpoint.
+ * @max_streams: The maximum number of streams supported
+ * by this EP (0 - 16, actual number is 2^n)
* @mult: multiplier, 'mult' value for SS Isoc EPs
* @maxburst: the maximum number of bursts supported by this EP (for usb3)
* @driver_data:for use by the gadget driver.
@@ -152,6 +156,7 @@ struct usb_ep {
const struct usb_ep_ops *ops;
struct list_head ep_list;
unsigned maxpacket:16;
+ unsigned max_streams:16;
unsigned mult:2;
unsigned pad:1;
unsigned maxburst:4;
@@ -921,6 +926,11 @@ static inline void usb_free_descriptors(struct usb_descriptor_header **v)
extern struct usb_ep *usb_ep_autoconfig(struct usb_gadget *,
struct usb_endpoint_descriptor *);
+
+extern struct usb_ep *usb_ep_autoconfig_ss(struct usb_gadget *,
+ struct usb_endpoint_descriptor *,
+ struct usb_ss_ep_comp_descriptor *);
+
extern void usb_ep_autoconfig_reset(struct usb_gadget *);
#endif /* __LINUX_USB_GADGET_H */
--
1.7.3.3
--
Sent by an employee of the Qualcomm Innovation Center, Inc.
The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum.
^ permalink raw reply related [flat|nested] 13+ messages in thread* [PATCH v11 6/7] usb:dummy_hcd: use the shared_hcd infrustructure
[not found] <1305805417-31750-1-git-send-email-tlinder@codeaurora.org>
` (4 preceding siblings ...)
2011-05-19 11:43 ` [PATCH/RESEND v11 5/7] usb: Add streams support to the gadget framework Tatyana Brokhman
@ 2011-05-19 11:43 ` Tatyana Brokhman
2011-05-19 18:48 ` Alan Stern
2011-05-19 11:43 ` [PATCH v11 7/7] usb: Adding SuperSpeed support to dummy_hcd Tatyana Brokhman
6 siblings, 1 reply; 13+ messages in thread
From: Tatyana Brokhman @ 2011-05-19 11:43 UTC (permalink / raw)
To: greg; +Cc: linux-usb, balbi, ablay, linux-arm-msm, Tatyana Brokhman,
open list
This patch is a preparation for adding SuperSpeed support to dummy hcd.
It takes the master side fields out of the struct dummy to a separate
structure. The init process was also modified to resemble the way it is
done by xHCI.
Signed-off-by: Tatyana Brokhman <tlinder@codeaurora.org>
---
drivers/usb/gadget/dummy_hcd.c | 503 +++++++++++++++++++++-------------------
1 files changed, 268 insertions(+), 235 deletions(-)
diff --git a/drivers/usb/gadget/dummy_hcd.c b/drivers/usb/gadget/dummy_hcd.c
index 61ff9279..cf197e1 100644
--- a/drivers/usb/gadget/dummy_hcd.c
+++ b/drivers/usb/gadget/dummy_hcd.c
@@ -152,6 +152,24 @@ enum dummy_rh_state {
DUMMY_RH_RUNNING
};
+struct dummy_hcd {
+ struct usb_hcd *hcd;
+
+ struct dummy *dum;
+ enum dummy_rh_state rh_state;
+ struct timer_list timer;
+ u32 port_status;
+ u32 old_status;
+ unsigned resuming:1;
+ unsigned long re_timeout;
+
+ struct usb_device *udev;
+ struct list_head urbp_list;
+
+ unsigned active:1;
+ unsigned old_active:1;
+};
+
struct dummy {
spinlock_t lock;
@@ -167,36 +185,26 @@ struct dummy {
u16 devstatus;
unsigned udc_suspended:1;
unsigned pullup:1;
- unsigned active:1;
- unsigned old_active:1;
/*
* MASTER/HOST side support
*/
- enum dummy_rh_state rh_state;
- struct timer_list timer;
- u32 port_status;
- u32 old_status;
- unsigned resuming:1;
- unsigned long re_timeout;
-
- struct usb_device *udev;
- struct list_head urbp_list;
+ struct dummy_hcd *hs_hcd;
};
-static inline struct dummy *hcd_to_dummy (struct usb_hcd *hcd)
+static inline struct dummy_hcd *hcd_to_dummy_hcd(struct usb_hcd *hcd)
{
- return (struct dummy *) (hcd->hcd_priv);
+ return (struct dummy_hcd *) (hcd->hcd_priv);
}
-static inline struct usb_hcd *dummy_to_hcd (struct dummy *dum)
+static inline struct usb_hcd *dummy_hcd_to_hcd(struct dummy_hcd *dum)
{
return container_of((void *) dum, struct usb_hcd, hcd_priv);
}
-static inline struct device *dummy_dev (struct dummy *dum)
+static inline struct device *dummy_dev(struct dummy_hcd *dum)
{
- return dummy_to_hcd(dum)->self.controller;
+ return dummy_hcd_to_hcd(dum)->self.controller;
}
static inline struct device *udc_dev (struct dummy *dum)
@@ -209,9 +217,10 @@ static inline struct dummy *ep_to_dummy (struct dummy_ep *ep)
return container_of (ep->gadget, struct dummy, gadget);
}
-static inline struct dummy *gadget_to_dummy (struct usb_gadget *gadget)
+static inline struct dummy_hcd *gadget_to_dummy_hcd(struct usb_gadget *gadget)
{
- return container_of (gadget, struct dummy, gadget);
+ struct dummy *dum = container_of(gadget, struct dummy, gadget);
+ return dum->hs_hcd;
}
static inline struct dummy *gadget_dev_to_dummy (struct device *dev)
@@ -219,7 +228,7 @@ static inline struct dummy *gadget_dev_to_dummy (struct device *dev)
return container_of (dev, struct dummy, gadget.dev);
}
-static struct dummy *the_controller;
+static struct dummy the_controller;
/*-------------------------------------------------------------------------*/
@@ -260,60 +269,64 @@ stop_activity (struct dummy *dum)
}
/* caller must hold lock */
-static void
-set_link_state (struct dummy *dum)
+static void set_link_state(struct dummy_hcd *dum_hcd)
{
- dum->active = 0;
- if ((dum->port_status & USB_PORT_STAT_POWER) == 0)
- dum->port_status = 0;
+ struct dummy *dum = dum_hcd->dum;
+
+ dum_hcd->active = 0;
+ if ((dum_hcd->port_status & USB_PORT_STAT_POWER) == 0)
+ dum_hcd->port_status = 0;
/* UDC suspend must cause a disconnect */
else if (!dum->pullup || dum->udc_suspended) {
- dum->port_status &= ~(USB_PORT_STAT_CONNECTION |
+ dum_hcd->port_status &= ~(USB_PORT_STAT_CONNECTION |
USB_PORT_STAT_ENABLE |
USB_PORT_STAT_LOW_SPEED |
USB_PORT_STAT_HIGH_SPEED |
USB_PORT_STAT_SUSPEND);
- if ((dum->old_status & USB_PORT_STAT_CONNECTION) != 0)
- dum->port_status |= (USB_PORT_STAT_C_CONNECTION << 16);
+ if ((dum_hcd->old_status & USB_PORT_STAT_CONNECTION) != 0)
+ dum_hcd->port_status |=
+ (USB_PORT_STAT_C_CONNECTION << 16);
} else {
- dum->port_status |= USB_PORT_STAT_CONNECTION;
- if ((dum->old_status & USB_PORT_STAT_CONNECTION) == 0)
- dum->port_status |= (USB_PORT_STAT_C_CONNECTION << 16);
- if ((dum->port_status & USB_PORT_STAT_ENABLE) == 0)
- dum->port_status &= ~USB_PORT_STAT_SUSPEND;
- else if ((dum->port_status & USB_PORT_STAT_SUSPEND) == 0 &&
- dum->rh_state != DUMMY_RH_SUSPENDED)
- dum->active = 1;
+ dum_hcd->port_status |= USB_PORT_STAT_CONNECTION;
+ if ((dum_hcd->old_status & USB_PORT_STAT_CONNECTION) == 0)
+ dum_hcd->port_status |=
+ (USB_PORT_STAT_C_CONNECTION << 16);
+ if ((dum_hcd->port_status & USB_PORT_STAT_ENABLE) == 0)
+ dum_hcd->port_status &= ~USB_PORT_STAT_SUSPEND;
+ else if ((dum_hcd->port_status & USB_PORT_STAT_SUSPEND) == 0 &&
+ dum_hcd->rh_state != DUMMY_RH_SUSPENDED)
+ dum_hcd->active = 1;
}
- if ((dum->port_status & USB_PORT_STAT_ENABLE) == 0 || dum->active)
- dum->resuming = 0;
+ if ((dum_hcd->port_status & USB_PORT_STAT_ENABLE) == 0 ||
+ dum_hcd->active)
+ dum_hcd->resuming = 0;
- if ((dum->port_status & USB_PORT_STAT_CONNECTION) == 0 ||
- (dum->port_status & USB_PORT_STAT_RESET) != 0) {
- if ((dum->old_status & USB_PORT_STAT_CONNECTION) != 0 &&
- (dum->old_status & USB_PORT_STAT_RESET) == 0 &&
+ if ((dum_hcd->port_status & USB_PORT_STAT_CONNECTION) == 0 ||
+ (dum_hcd->port_status & USB_PORT_STAT_RESET) != 0) {
+ if ((dum_hcd->old_status & USB_PORT_STAT_CONNECTION) != 0 &&
+ (dum_hcd->old_status & USB_PORT_STAT_RESET) == 0 &&
dum->driver) {
stop_activity (dum);
spin_unlock (&dum->lock);
dum->driver->disconnect (&dum->gadget);
spin_lock (&dum->lock);
}
- } else if (dum->active != dum->old_active) {
- if (dum->old_active && dum->driver->suspend) {
+ } else if (dum_hcd->active != dum_hcd->old_active) {
+ if (dum_hcd->old_active && dum->driver->suspend) {
spin_unlock (&dum->lock);
dum->driver->suspend (&dum->gadget);
spin_lock (&dum->lock);
- } else if (!dum->old_active && dum->driver->resume) {
+ } else if (!dum_hcd->old_active && dum->driver->resume) {
spin_unlock (&dum->lock);
dum->driver->resume (&dum->gadget);
spin_lock (&dum->lock);
}
}
- dum->old_status = dum->port_status;
- dum->old_active = dum->active;
+ dum_hcd->old_status = dum_hcd->port_status;
+ dum_hcd->old_active = dum_hcd->active;
}
/*-------------------------------------------------------------------------*/
@@ -332,6 +345,7 @@ static int
dummy_enable (struct usb_ep *_ep, const struct usb_endpoint_descriptor *desc)
{
struct dummy *dum;
+ struct dummy_hcd *dum_hcd;
struct dummy_ep *ep;
unsigned max;
int retval;
@@ -341,9 +355,17 @@ dummy_enable (struct usb_ep *_ep, const struct usb_endpoint_descriptor *desc)
|| desc->bDescriptorType != USB_DT_ENDPOINT)
return -EINVAL;
dum = ep_to_dummy (ep);
- if (!dum->driver || !is_enabled (dum))
+ if (!dum->driver)
+ return -ESHUTDOWN;
+ dum_hcd = dum->hs_hcd;
+ if (!is_enabled(dum_hcd))
return -ESHUTDOWN;
- max = le16_to_cpu(desc->wMaxPacketSize) & 0x3ff;
+
+ /*
+ * For HS/FS devices only bits 0..10 of the wMaxPacketSize represent the
+ * maximum packet size.
+ */
+ max = le16_to_cpu(desc->wMaxPacketSize) & 0x7ff;
/* drivers must not request bad settings, since lower levels
* (hardware or its drivers) may not check. some endpoints
@@ -507,6 +529,7 @@ dummy_queue (struct usb_ep *_ep, struct usb_request *_req,
struct dummy_ep *ep;
struct dummy_request *req;
struct dummy *dum;
+ struct dummy_hcd *dum_hcd;
unsigned long flags;
req = usb_request_to_dummy_request (_req);
@@ -518,7 +541,8 @@ dummy_queue (struct usb_ep *_ep, struct usb_request *_req,
return -EINVAL;
dum = ep_to_dummy (ep);
- if (!dum->driver || !is_enabled (dum))
+ dum_hcd = dum->hs_hcd;
+ if (!dum->driver || !is_enabled(dum_hcd))
return -ESHUTDOWN;
#if 0
@@ -662,24 +686,24 @@ static int dummy_g_get_frame (struct usb_gadget *_gadget)
static int dummy_wakeup (struct usb_gadget *_gadget)
{
- struct dummy *dum;
+ struct dummy_hcd *dum_hcd;
- dum = gadget_to_dummy (_gadget);
- if (!(dum->devstatus & ( (1 << USB_DEVICE_B_HNP_ENABLE)
+ dum_hcd = gadget_to_dummy_hcd(_gadget);
+ if (!(dum_hcd->dum->devstatus & ((1 << USB_DEVICE_B_HNP_ENABLE)
| (1 << USB_DEVICE_REMOTE_WAKEUP))))
return -EINVAL;
- if ((dum->port_status & USB_PORT_STAT_CONNECTION) == 0)
+ if ((dum_hcd->port_status & USB_PORT_STAT_CONNECTION) == 0)
return -ENOLINK;
- if ((dum->port_status & USB_PORT_STAT_SUSPEND) == 0 &&
- dum->rh_state != DUMMY_RH_SUSPENDED)
+ if ((dum_hcd->port_status & USB_PORT_STAT_SUSPEND) == 0 &&
+ dum_hcd->rh_state != DUMMY_RH_SUSPENDED)
return -EIO;
/* FIXME: What if the root hub is suspended but the port isn't? */
/* hub notices our request, issues downstream resume, etc */
- dum->resuming = 1;
- dum->re_timeout = jiffies + msecs_to_jiffies(20);
- mod_timer (&dummy_to_hcd (dum)->rh_timer, dum->re_timeout);
+ dum_hcd->resuming = 1;
+ dum_hcd->re_timeout = jiffies + msecs_to_jiffies(20);
+ mod_timer(&dum_hcd->hcd->rh_timer, dum_hcd->re_timeout);
return 0;
}
@@ -687,7 +711,7 @@ static int dummy_set_selfpowered (struct usb_gadget *_gadget, int value)
{
struct dummy *dum;
- dum = gadget_to_dummy (_gadget);
+ dum = (gadget_to_dummy_hcd(_gadget))->dum;
if (value)
dum->devstatus |= (1 << USB_DEVICE_SELF_POWERED);
else
@@ -700,13 +724,12 @@ static int dummy_pullup (struct usb_gadget *_gadget, int value)
struct dummy *dum;
unsigned long flags;
- dum = gadget_to_dummy (_gadget);
+ dum = gadget_to_dummy_hcd(_gadget)->dum;
spin_lock_irqsave (&dum->lock, flags);
dum->pullup = (value != 0);
- set_link_state (dum);
+ set_link_state(dum->hs_hcd);
spin_unlock_irqrestore (&dum->lock, flags);
-
- usb_hcd_poll_rh_status (dummy_to_hcd (dum));
+ usb_hcd_poll_rh_status(dum->hs_hcd->hcd);
return 0;
}
@@ -751,7 +774,7 @@ int
usb_gadget_probe_driver(struct usb_gadget_driver *driver,
int (*bind)(struct usb_gadget *))
{
- struct dummy *dum = the_controller;
+ struct dummy *dum = &the_controller;
int retval, i;
if (!dum)
@@ -787,7 +810,8 @@ usb_gadget_probe_driver(struct usb_gadget_driver *driver,
}
dum->gadget.ep0 = &dum->ep [0].ep;
- dum->ep [0].ep.maxpacket = 64;
+ dum->gadget.speed = min((u8)driver->speed, (u8)USB_SPEED_HIGH) ;
+ dum->ep[0].ep.maxpacket = 64;
list_del_init (&dum->ep [0].ep.ep_list);
INIT_LIST_HEAD(&dum->fifo_req.queue);
@@ -806,10 +830,11 @@ usb_gadget_probe_driver(struct usb_gadget_driver *driver,
/* khubd will enumerate this in a while */
spin_lock_irq (&dum->lock);
dum->pullup = 1;
- set_link_state (dum);
+ dum->gadget.is_otg = (dum->hs_hcd->hcd->self.otg_port != 0);
+ set_link_state(dum->hs_hcd);
spin_unlock_irq (&dum->lock);
- usb_hcd_poll_rh_status (dummy_to_hcd (dum));
+ usb_hcd_poll_rh_status(dum->hs_hcd->hcd);
return 0;
}
EXPORT_SYMBOL(usb_gadget_probe_driver);
@@ -817,7 +842,7 @@ EXPORT_SYMBOL(usb_gadget_probe_driver);
int
usb_gadget_unregister_driver (struct usb_gadget_driver *driver)
{
- struct dummy *dum = the_controller;
+ struct dummy *dum = &the_controller;
unsigned long flags;
if (!dum)
@@ -830,7 +855,7 @@ usb_gadget_unregister_driver (struct usb_gadget_driver *driver)
spin_lock_irqsave (&dum->lock, flags);
dum->pullup = 0;
- set_link_state (dum);
+ set_link_state(dum->hs_hcd);
spin_unlock_irqrestore (&dum->lock, flags);
driver->unbind (&dum->gadget);
@@ -839,10 +864,9 @@ usb_gadget_unregister_driver (struct usb_gadget_driver *driver)
spin_lock_irqsave (&dum->lock, flags);
dum->pullup = 0;
- set_link_state (dum);
+ set_link_state(dum->hs_hcd);
spin_unlock_irqrestore (&dum->lock, flags);
-
- usb_hcd_poll_rh_status (dummy_to_hcd (dum));
+ usb_hcd_poll_rh_status(dum->hs_hcd->hcd);
return 0;
}
EXPORT_SYMBOL (usb_gadget_unregister_driver);
@@ -864,25 +888,18 @@ EXPORT_SYMBOL (net2280_set_fifo_mode);
static void
dummy_gadget_release (struct device *dev)
{
- struct dummy *dum = gadget_dev_to_dummy (dev);
-
- usb_put_hcd (dummy_to_hcd (dum));
+ return;
}
static int dummy_udc_probe (struct platform_device *pdev)
{
- struct dummy *dum = the_controller;
+ struct dummy *dum = &the_controller;
int rc;
- usb_get_hcd(dummy_to_hcd(dum));
-
dum->gadget.name = gadget_name;
dum->gadget.ops = &dummy_ops;
dum->gadget.is_dualspeed = 1;
- /* maybe claim OTG support, though we won't complete HNP */
- dum->gadget.is_otg = (dummy_to_hcd(dum)->self.otg_port != 0);
-
dev_set_name(&dum->gadget.dev, "gadget");
dum->gadget.dev.parent = &pdev->dev;
dum->gadget.dev.release = dummy_gadget_release;
@@ -917,10 +934,10 @@ static int dummy_udc_suspend (struct platform_device *pdev, pm_message_t state)
dev_dbg (&pdev->dev, "%s\n", __func__);
spin_lock_irq (&dum->lock);
dum->udc_suspended = 1;
- set_link_state (dum);
+ set_link_state(dum->hs_hcd);
spin_unlock_irq (&dum->lock);
- usb_hcd_poll_rh_status (dummy_to_hcd (dum));
+ usb_hcd_poll_rh_status(dum->hs_hcd->hcd);
return 0;
}
@@ -931,10 +948,10 @@ static int dummy_udc_resume (struct platform_device *pdev)
dev_dbg (&pdev->dev, "%s\n", __func__);
spin_lock_irq (&dum->lock);
dum->udc_suspended = 0;
- set_link_state (dum);
+ set_link_state(dum->hs_hcd);
spin_unlock_irq (&dum->lock);
- usb_hcd_poll_rh_status (dummy_to_hcd (dum));
+ usb_hcd_poll_rh_status(dum->hs_hcd->hcd);
return 0;
}
@@ -968,7 +985,7 @@ static int dummy_urb_enqueue (
struct urb *urb,
gfp_t mem_flags
) {
- struct dummy *dum;
+ struct dummy_hcd *dum_hcd;
struct urbp *urbp;
unsigned long flags;
int rc;
@@ -981,51 +998,51 @@ static int dummy_urb_enqueue (
return -ENOMEM;
urbp->urb = urb;
- dum = hcd_to_dummy (hcd);
- spin_lock_irqsave (&dum->lock, flags);
+ dum_hcd = hcd_to_dummy_hcd(hcd);
+ spin_lock_irqsave(&dum_hcd->dum->lock, flags);
rc = usb_hcd_link_urb_to_ep(hcd, urb);
if (rc) {
kfree(urbp);
goto done;
}
- if (!dum->udev) {
- dum->udev = urb->dev;
- usb_get_dev (dum->udev);
- } else if (unlikely (dum->udev != urb->dev))
- dev_err (dummy_dev(dum), "usb_device address has changed!\n");
+ if (!dum_hcd->udev) {
+ dum_hcd->udev = urb->dev;
+ usb_get_dev(dum_hcd->udev);
+ } else if (unlikely(dum_hcd->udev != urb->dev))
+ dev_err(dummy_dev(dum_hcd), "usb_device address has changed!\n");
- list_add_tail (&urbp->urbp_list, &dum->urbp_list);
+ list_add_tail(&urbp->urbp_list, &dum_hcd->urbp_list);
urb->hcpriv = urbp;
if (usb_pipetype (urb->pipe) == PIPE_CONTROL)
urb->error_count = 1; /* mark as a new urb */
/* kick the scheduler, it'll do the rest */
- if (!timer_pending (&dum->timer))
- mod_timer (&dum->timer, jiffies + 1);
+ if (!timer_pending(&dum_hcd->timer))
+ mod_timer(&dum_hcd->timer, jiffies + 1);
done:
- spin_unlock_irqrestore(&dum->lock, flags);
+ spin_unlock_irqrestore(&dum_hcd->dum->lock, flags);
return rc;
}
static int dummy_urb_dequeue(struct usb_hcd *hcd, struct urb *urb, int status)
{
- struct dummy *dum;
+ struct dummy_hcd *dum_hcd;
unsigned long flags;
int rc;
/* giveback happens automatically in timer callback,
* so make sure the callback happens */
- dum = hcd_to_dummy (hcd);
- spin_lock_irqsave (&dum->lock, flags);
+ dum_hcd = hcd_to_dummy_hcd(hcd);
+ spin_lock_irqsave(&dum_hcd->dum->lock, flags);
rc = usb_hcd_check_unlink_urb(hcd, urb, status);
- if (!rc && dum->rh_state != DUMMY_RH_RUNNING &&
- !list_empty(&dum->urbp_list))
- mod_timer (&dum->timer, jiffies);
+ if (!rc && dum_hcd->rh_state != DUMMY_RH_RUNNING &&
+ !list_empty(&dum_hcd->urbp_list))
+ mod_timer(&dum_hcd->timer, jiffies);
- spin_unlock_irqrestore (&dum->lock, flags);
+ spin_unlock_irqrestore(&dum_hcd->dum->lock, flags);
return rc;
}
@@ -1165,7 +1182,7 @@ static int periodic_bytes (struct dummy *dum, struct dummy_ep *ep)
return limit;
}
-#define is_active(dum) ((dum->port_status & \
+#define is_active(dum_hcd) ((dum_hcd->port_status & \
(USB_PORT_STAT_CONNECTION | USB_PORT_STAT_ENABLE | \
USB_PORT_STAT_SUSPEND)) \
== (USB_PORT_STAT_CONNECTION | USB_PORT_STAT_ENABLE))
@@ -1174,7 +1191,7 @@ static struct dummy_ep *find_endpoint (struct dummy *dum, u8 address)
{
int i;
- if (!is_active (dum))
+ if (!is_active(dum->hs_hcd))
return NULL;
if ((address & ~USB_DIR_IN) == 0)
return &dum->ep [0];
@@ -1211,11 +1228,12 @@ static struct dummy_ep *find_endpoint (struct dummy *dum, u8 address)
* 1 - if the request wasn't handles
* error code on error
*/
-static int handle_control_request(struct dummy *dum, struct urb *urb,
+static int handle_control_request(struct dummy_hcd *dum_hcd, struct urb *urb,
struct usb_ctrlrequest *setup,
int *status)
{
struct dummy_ep *ep2;
+ struct dummy *dum = dum_hcd->dum;
int ret_val = 1;
unsigned w_index;
unsigned w_value;
@@ -1334,9 +1352,10 @@ static int handle_control_request(struct dummy *dum, struct urb *urb,
/* drive both sides of the transfers; looks like irq handlers to
* both drivers except the callbacks aren't in_irq().
*/
-static void dummy_timer (unsigned long _dum)
+static void dummy_timer(unsigned long _dum_hcd)
{
- struct dummy *dum = (struct dummy *) _dum;
+ struct dummy_hcd *dum_hcd = (struct dummy_hcd *) _dum_hcd;
+ struct dummy *dum = dum_hcd->dum;
struct urbp *urbp, *tmp;
unsigned long flags;
int limit, total;
@@ -1354,7 +1373,7 @@ static void dummy_timer (unsigned long _dum)
total = 512/*bytes*/ * 13/*packets*/ * 8/*uframes*/;
break;
default:
- dev_err (dummy_dev(dum), "bogus device speed\n");
+ dev_err(dummy_dev(dum_hcd), "bogus device speed\n");
return;
}
@@ -1363,8 +1382,8 @@ static void dummy_timer (unsigned long _dum)
/* look at each urb queued by the host side driver */
spin_lock_irqsave (&dum->lock, flags);
- if (!dum->udev) {
- dev_err (dummy_dev(dum),
+ if (!dum_hcd->udev) {
+ dev_err(dummy_dev(dum_hcd),
"timer fired with no URBs pending?\n");
spin_unlock_irqrestore (&dum->lock, flags);
return;
@@ -1377,7 +1396,7 @@ static void dummy_timer (unsigned long _dum)
}
restart:
- list_for_each_entry_safe (urbp, tmp, &dum->urbp_list, urbp_list) {
+ list_for_each_entry_safe(urbp, tmp, &dum_hcd->urbp_list, urbp_list) {
struct urb *urb;
struct dummy_request *req;
u8 address;
@@ -1388,7 +1407,7 @@ restart:
urb = urbp->urb;
if (urb->unlinked)
goto return_urb;
- else if (dum->rh_state != DUMMY_RH_RUNNING)
+ else if (dum_hcd->rh_state != DUMMY_RH_RUNNING)
continue;
type = usb_pipetype (urb->pipe);
@@ -1406,7 +1425,7 @@ restart:
ep = find_endpoint(dum, address);
if (!ep) {
/* set_configuration() disagreement */
- dev_dbg (dummy_dev(dum),
+ dev_dbg(dummy_dev(dum_hcd),
"no ep configured for urb %p\n",
urb);
status = -EPROTO;
@@ -1422,7 +1441,7 @@ restart:
}
if (ep->halted && !ep->setup_stage) {
/* NOTE: must not be iso! */
- dev_dbg (dummy_dev(dum), "ep %s halted, urb %p\n",
+ dev_dbg(dummy_dev(dum_hcd), "ep %s halted, urb %p\n",
ep->ep.name, urb);
status = -EPIPE;
goto return_urb;
@@ -1457,7 +1476,7 @@ restart:
ep->setup_stage = 0;
ep->halted = 0;
- value = handle_control_request(dum, urb, &setup,
+ value = handle_control_request(dum_hcd, urb, &setup,
&status);
/* gadget driver handles all other requests. block
@@ -1527,20 +1546,20 @@ return_urb:
if (ep)
ep->already_seen = ep->setup_stage = 0;
- usb_hcd_unlink_urb_from_ep(dummy_to_hcd(dum), urb);
+ usb_hcd_unlink_urb_from_ep(dum_hcd->hcd, urb);
spin_unlock (&dum->lock);
- usb_hcd_giveback_urb(dummy_to_hcd(dum), urb, status);
+ usb_hcd_giveback_urb(dum_hcd->hcd, urb, status);
spin_lock (&dum->lock);
goto restart;
}
- if (list_empty (&dum->urbp_list)) {
- usb_put_dev (dum->udev);
- dum->udev = NULL;
- } else if (dum->rh_state == DUMMY_RH_RUNNING) {
+ if (list_empty(&dum_hcd->urbp_list)) {
+ usb_put_dev(dum_hcd->udev);
+ dum_hcd->udev = NULL;
+ } else if (dum_hcd->rh_state == DUMMY_RH_RUNNING) {
/* want a 1 msec delay here */
- mod_timer (&dum->timer, jiffies + msecs_to_jiffies(1));
+ mod_timer(&dum_hcd->timer, jiffies + msecs_to_jiffies(1));
}
spin_unlock_irqrestore (&dum->lock, flags);
@@ -1557,32 +1576,32 @@ return_urb:
static int dummy_hub_status (struct usb_hcd *hcd, char *buf)
{
- struct dummy *dum;
+ struct dummy_hcd *dum_hcd;
unsigned long flags;
int retval = 0;
- dum = hcd_to_dummy (hcd);
+ dum_hcd = hcd_to_dummy_hcd(hcd);
- spin_lock_irqsave (&dum->lock, flags);
+ spin_lock_irqsave(&dum_hcd->dum->lock, flags);
if (!HCD_HW_ACCESSIBLE(hcd))
goto done;
- if (dum->resuming && time_after_eq (jiffies, dum->re_timeout)) {
- dum->port_status |= (USB_PORT_STAT_C_SUSPEND << 16);
- dum->port_status &= ~USB_PORT_STAT_SUSPEND;
- set_link_state (dum);
+ if (dum_hcd->resuming && time_after_eq(jiffies, dum_hcd->re_timeout)) {
+ dum_hcd->port_status |= (USB_PORT_STAT_C_SUSPEND << 16);
+ dum_hcd->port_status &= ~USB_PORT_STAT_SUSPEND;
+ set_link_state(dum_hcd);
}
- if ((dum->port_status & PORT_C_MASK) != 0) {
+ if ((dum_hcd->port_status & PORT_C_MASK) != 0) {
*buf = (1 << 1);
- dev_dbg (dummy_dev(dum), "port status 0x%08x has changes\n",
- dum->port_status);
+ dev_dbg(dummy_dev(dum_hcd), "port status 0x%08x has changes\n",
+ dum_hcd->port_status);
retval = 1;
- if (dum->rh_state == DUMMY_RH_SUSPENDED)
+ if (dum_hcd->rh_state == DUMMY_RH_SUSPENDED)
usb_hcd_resume_root_hub (hcd);
}
done:
- spin_unlock_irqrestore (&dum->lock, flags);
+ spin_unlock_irqrestore(&dum_hcd->dum->lock, flags);
return retval;
}
@@ -1606,39 +1625,40 @@ static int dummy_hub_control (
char *buf,
u16 wLength
) {
- struct dummy *dum;
+ struct dummy_hcd *dum_hcd;
int retval = 0;
unsigned long flags;
if (!HCD_HW_ACCESSIBLE(hcd))
return -ETIMEDOUT;
- dum = hcd_to_dummy (hcd);
- spin_lock_irqsave (&dum->lock, flags);
+ dum_hcd = hcd_to_dummy_hcd(hcd);
+
+ spin_lock_irqsave(&dum_hcd->dum->lock, flags);
switch (typeReq) {
case ClearHubFeature:
break;
case ClearPortFeature:
switch (wValue) {
case USB_PORT_FEAT_SUSPEND:
- if (dum->port_status & USB_PORT_STAT_SUSPEND) {
+ if (dum_hcd->port_status & USB_PORT_STAT_SUSPEND) {
/* 20msec resume signaling */
- dum->resuming = 1;
- dum->re_timeout = jiffies +
+ dum_hcd->resuming = 1;
+ dum_hcd->re_timeout = jiffies +
msecs_to_jiffies(20);
}
break;
case USB_PORT_FEAT_POWER:
- if (dum->port_status & USB_PORT_STAT_POWER)
- dev_dbg (dummy_dev(dum), "power-off\n");
+ if (dum_hcd->port_status & USB_PORT_STAT_POWER)
+ dev_dbg(dummy_dev(dum_hcd), "power-off\n");
/* FALLS THROUGH */
default:
- dum->port_status &= ~(1 << wValue);
- set_link_state (dum);
+ dum_hcd->port_status &= ~(1 << wValue);
+ set_link_state(dum_hcd);
}
break;
case GetHubDescriptor:
- hub_descriptor ((struct usb_hub_descriptor *) buf);
+ hub_descriptor((struct usb_hub_descriptor *) buf);
break;
case GetHubStatus:
*(__le32 *) buf = cpu_to_le32 (0);
@@ -1650,39 +1670,38 @@ static int dummy_hub_control (
/* whoever resets or resumes must GetPortStatus to
* complete it!!
*/
- if (dum->resuming &&
- time_after_eq (jiffies, dum->re_timeout)) {
- dum->port_status |= (USB_PORT_STAT_C_SUSPEND << 16);
- dum->port_status &= ~USB_PORT_STAT_SUSPEND;
+ if (dum_hcd->resuming &&
+ time_after_eq(jiffies, dum_hcd->re_timeout)) {
+ dum_hcd->port_status |= (USB_PORT_STAT_C_SUSPEND << 16);
+ dum_hcd->port_status &= ~USB_PORT_STAT_SUSPEND;
}
- if ((dum->port_status & USB_PORT_STAT_RESET) != 0 &&
- time_after_eq (jiffies, dum->re_timeout)) {
- dum->port_status |= (USB_PORT_STAT_C_RESET << 16);
- dum->port_status &= ~USB_PORT_STAT_RESET;
- if (dum->pullup) {
- dum->port_status |= USB_PORT_STAT_ENABLE;
- /* give it the best speed we agree on */
- dum->gadget.speed = dum->driver->speed;
- dum->gadget.ep0->maxpacket = 64;
- switch (dum->gadget.speed) {
+ if ((dum_hcd->port_status & USB_PORT_STAT_RESET) != 0 &&
+ time_after_eq(jiffies, dum_hcd->re_timeout)) {
+ dum_hcd->port_status |= (USB_PORT_STAT_C_RESET << 16);
+ dum_hcd->port_status &= ~USB_PORT_STAT_RESET;
+ if (dum_hcd->dum->pullup) {
+ dum_hcd->port_status |= USB_PORT_STAT_ENABLE;
+ switch (dum_hcd->dum->gadget.speed) {
case USB_SPEED_HIGH:
- dum->port_status |=
- USB_PORT_STAT_HIGH_SPEED;
+ dum_hcd->port_status |=
+ USB_PORT_STAT_HIGH_SPEED;
break;
case USB_SPEED_LOW:
- dum->gadget.ep0->maxpacket = 8;
- dum->port_status |=
+ dum_hcd->dum->gadget.ep0->
+ maxpacket = 8;
+ dum_hcd->port_status |=
USB_PORT_STAT_LOW_SPEED;
break;
default:
- dum->gadget.speed = USB_SPEED_FULL;
+ dum_hcd->dum->gadget.speed =
+ USB_SPEED_FULL;
break;
}
}
}
- set_link_state (dum);
- ((__le16 *) buf)[0] = cpu_to_le16 (dum->port_status);
- ((__le16 *) buf)[1] = cpu_to_le16 (dum->port_status >> 16);
+ set_link_state(dum_hcd);
+ ((__le16 *) buf)[0] = cpu_to_le16 (dum_hcd->port_status);
+ ((__le16 *) buf)[1] = cpu_to_le16 (dum_hcd->port_status >> 16);
break;
case SetHubFeature:
retval = -EPIPE;
@@ -1690,87 +1709,91 @@ static int dummy_hub_control (
case SetPortFeature:
switch (wValue) {
case USB_PORT_FEAT_SUSPEND:
- if (dum->active) {
- dum->port_status |= USB_PORT_STAT_SUSPEND;
+ if (dum_hcd->active) {
+ dum_hcd->port_status |= USB_PORT_STAT_SUSPEND;
/* HNP would happen here; for now we
* assume b_bus_req is always true.
*/
- set_link_state (dum);
+ set_link_state(dum_hcd);
if (((1 << USB_DEVICE_B_HNP_ENABLE)
- & dum->devstatus) != 0)
- dev_dbg (dummy_dev(dum),
+ & dum_hcd->dum->devstatus) != 0)
+ dev_dbg(dummy_dev(dum_hcd),
"no HNP yet!\n");
}
break;
case USB_PORT_FEAT_POWER:
- dum->port_status |= USB_PORT_STAT_POWER;
- set_link_state (dum);
+ dum_hcd->port_status |= USB_PORT_STAT_POWER;
+ set_link_state(dum_hcd);
break;
case USB_PORT_FEAT_RESET:
/* if it's already enabled, disable */
- dum->port_status &= ~(USB_PORT_STAT_ENABLE
+ dum_hcd->port_status &= ~(USB_PORT_STAT_ENABLE
| USB_PORT_STAT_LOW_SPEED
| USB_PORT_STAT_HIGH_SPEED);
- dum->devstatus = 0;
- /* 50msec reset signaling */
- dum->re_timeout = jiffies + msecs_to_jiffies(50);
+ /*
+ * We want to reset device status. All but the
+ * Self powered feature
+ */
+ dum_hcd->dum->devstatus &=
+ (1 << USB_DEVICE_SELF_POWERED);
+ dum_hcd->re_timeout = jiffies + msecs_to_jiffies(50);
/* FALLS THROUGH */
default:
- if ((dum->port_status & USB_PORT_STAT_POWER) != 0) {
- dum->port_status |= (1 << wValue);
- set_link_state (dum);
+ if ((dum_hcd->port_status &
+ USB_PORT_STAT_POWER) != 0) {
+ dum_hcd->port_status |= (1 << wValue);
+ set_link_state(dum_hcd);
}
}
break;
default:
- dev_dbg (dummy_dev(dum),
+ dev_dbg(dummy_dev(dum_hcd),
"hub control req%04x v%04x i%04x l%d\n",
typeReq, wValue, wIndex, wLength);
-
/* "protocol stall" on error */
retval = -EPIPE;
}
- spin_unlock_irqrestore (&dum->lock, flags);
+ spin_unlock_irqrestore(&dum_hcd->dum->lock, flags);
- if ((dum->port_status & PORT_C_MASK) != 0)
+ if ((dum_hcd->port_status & PORT_C_MASK) != 0)
usb_hcd_poll_rh_status (hcd);
return retval;
}
static int dummy_bus_suspend (struct usb_hcd *hcd)
{
- struct dummy *dum = hcd_to_dummy (hcd);
+ struct dummy_hcd *dum_hcd = hcd_to_dummy_hcd(hcd);
dev_dbg (&hcd->self.root_hub->dev, "%s\n", __func__);
- spin_lock_irq (&dum->lock);
- dum->rh_state = DUMMY_RH_SUSPENDED;
- set_link_state (dum);
+ spin_lock_irq(&dum_hcd->dum->lock);
+ dum_hcd->rh_state = DUMMY_RH_SUSPENDED;
+ set_link_state(dum_hcd);
hcd->state = HC_STATE_SUSPENDED;
- spin_unlock_irq (&dum->lock);
+ spin_unlock_irq(&dum_hcd->dum->lock);
return 0;
}
static int dummy_bus_resume (struct usb_hcd *hcd)
{
- struct dummy *dum = hcd_to_dummy (hcd);
+ struct dummy_hcd *dum_hcd = hcd_to_dummy_hcd(hcd);
int rc = 0;
dev_dbg (&hcd->self.root_hub->dev, "%s\n", __func__);
- spin_lock_irq (&dum->lock);
+ spin_lock_irq(&dum_hcd->dum->lock);
if (!HCD_HW_ACCESSIBLE(hcd)) {
rc = -ESHUTDOWN;
} else {
- dum->rh_state = DUMMY_RH_RUNNING;
- set_link_state (dum);
- if (!list_empty(&dum->urbp_list))
- mod_timer (&dum->timer, jiffies);
+ dum_hcd->rh_state = DUMMY_RH_RUNNING;
+ set_link_state(dum_hcd);
+ if (!list_empty(&dum_hcd->urbp_list))
+ mod_timer(&dum_hcd->timer, jiffies);
hcd->state = HC_STATE_RUNNING;
}
- spin_unlock_irq (&dum->lock);
+ spin_unlock_irq(&dum_hcd->dum->lock);
return rc;
}
@@ -1806,43 +1829,41 @@ static ssize_t
show_urbs (struct device *dev, struct device_attribute *attr, char *buf)
{
struct usb_hcd *hcd = dev_get_drvdata (dev);
- struct dummy *dum = hcd_to_dummy (hcd);
+ struct dummy_hcd *dum_hcd = hcd_to_dummy_hcd(hcd);
struct urbp *urbp;
size_t size = 0;
unsigned long flags;
- spin_lock_irqsave (&dum->lock, flags);
- list_for_each_entry (urbp, &dum->urbp_list, urbp_list) {
+ spin_lock_irqsave(&dum_hcd->dum->lock, flags);
+ list_for_each_entry(urbp, &dum_hcd->urbp_list, urbp_list) {
size_t temp;
temp = show_urb (buf, PAGE_SIZE - size, urbp->urb);
buf += temp;
size += temp;
}
- spin_unlock_irqrestore (&dum->lock, flags);
+ spin_unlock_irqrestore(&dum_hcd->dum->lock, flags);
return size;
}
static DEVICE_ATTR (urbs, S_IRUGO, show_urbs, NULL);
-static int dummy_start (struct usb_hcd *hcd)
+static int dummy_start(struct usb_hcd *hcd)
{
- struct dummy *dum;
-
- dum = hcd_to_dummy (hcd);
+ struct dummy_hcd *dum_hcd = hcd_to_dummy_hcd(hcd);
/*
* MASTER side init ... we emulate a root hub that'll only ever
* talk to one device (the slave side). Also appears in sysfs,
* just like more familiar pci-based HCDs.
*/
- spin_lock_init (&dum->lock);
- init_timer (&dum->timer);
- dum->timer.function = dummy_timer;
- dum->timer.data = (unsigned long) dum;
- dum->rh_state = DUMMY_RH_RUNNING;
+ spin_lock_init(&dum_hcd->dum->lock);
+ init_timer(&dum_hcd->timer);
+ dum_hcd->timer.function = dummy_timer;
+ dum_hcd->timer.data = (unsigned long)dum_hcd;
+ dum_hcd->rh_state = DUMMY_RH_RUNNING;
- INIT_LIST_HEAD (&dum->urbp_list);
+ INIT_LIST_HEAD(&dum_hcd->urbp_list);
hcd->power_budget = POWER_BUDGET;
hcd->state = HC_STATE_RUNNING;
@@ -1853,18 +1874,17 @@ static int dummy_start (struct usb_hcd *hcd)
#endif
/* FIXME 'urbs' should be a per-device thing, maybe in usbcore */
- return device_create_file (dummy_dev(dum), &dev_attr_urbs);
+ return device_create_file(hcd->self.controller, &dev_attr_urbs);
}
static void dummy_stop (struct usb_hcd *hcd)
{
struct dummy *dum;
- dum = hcd_to_dummy (hcd);
-
- device_remove_file (dummy_dev(dum), &dev_attr_urbs);
+ dum = (hcd_to_dummy_hcd(hcd))->dum;
+ device_remove_file(hcd->self.controller, &dev_attr_urbs);
usb_gadget_unregister_driver (dum->driver);
- dev_info (dummy_dev(dum), "stopped\n");
+ dev_info(hcd->self.controller, "stopped\n");
}
/*-------------------------------------------------------------------------*/
@@ -1874,13 +1894,27 @@ static int dummy_h_get_frame (struct usb_hcd *hcd)
return dummy_g_get_frame (NULL);
}
+static int dummy_setup(struct usb_hcd *hcd)
+{
+ if (usb_hcd_is_primary_hcd(hcd)) {
+ the_controller.hs_hcd = hcd_to_dummy_hcd(hcd);
+ the_controller.hs_hcd->hcd = hcd;
+ the_controller.hs_hcd->dum = &the_controller;
+ /* Mark the first roothub as being USB 2.0. */
+ hcd->speed = HCD_USB2;
+ hcd->self.root_hub->speed = USB_SPEED_HIGH;
+ }
+ return 0;
+}
+
static const struct hc_driver dummy_hcd = {
.description = (char *) driver_name,
.product_desc = "Dummy host controller",
- .hcd_priv_size = sizeof(struct dummy),
+ .hcd_priv_size = sizeof(struct dummy_hcd),
.flags = HCD_USB2,
+ .reset = dummy_setup,
.start = dummy_start,
.stop = dummy_stop,
@@ -1897,46 +1931,45 @@ static const struct hc_driver dummy_hcd = {
static int dummy_hcd_probe(struct platform_device *pdev)
{
- struct usb_hcd *hcd;
+ struct usb_hcd *hs_hcd;
int retval;
dev_info(&pdev->dev, "%s, driver " DRIVER_VERSION "\n", driver_desc);
- hcd = usb_create_hcd(&dummy_hcd, &pdev->dev, dev_name(&pdev->dev));
- if (!hcd)
+ hs_hcd = usb_create_hcd(&dummy_hcd, &pdev->dev, dev_name(&pdev->dev));
+ if (!hs_hcd)
return -ENOMEM;
- the_controller = hcd_to_dummy (hcd);
- retval = usb_add_hcd(hcd, 0, 0);
+ retval = usb_add_hcd(hs_hcd, 0, 0);
if (retval != 0) {
- usb_put_hcd (hcd);
- the_controller = NULL;
+ usb_put_hcd(hs_hcd);
+ the_controller.hs_hcd = NULL;
}
return retval;
}
static int dummy_hcd_remove (struct platform_device *pdev)
{
- struct usb_hcd *hcd;
+ struct dummy *dum;
- hcd = platform_get_drvdata (pdev);
- usb_remove_hcd (hcd);
- usb_put_hcd (hcd);
- the_controller = NULL;
+ dum = (hcd_to_dummy_hcd(platform_get_drvdata(pdev)))->dum;
+ usb_remove_hcd(dum->hs_hcd->hcd);
+ usb_put_hcd(dum->hs_hcd->hcd);
+ the_controller.hs_hcd = NULL;
return 0;
}
static int dummy_hcd_suspend (struct platform_device *pdev, pm_message_t state)
{
struct usb_hcd *hcd;
- struct dummy *dum;
+ struct dummy_hcd *dum_hcd;
int rc = 0;
dev_dbg (&pdev->dev, "%s\n", __func__);
hcd = platform_get_drvdata (pdev);
- dum = hcd_to_dummy (hcd);
- if (dum->rh_state == DUMMY_RH_RUNNING) {
+ dum_hcd = hcd_to_dummy_hcd(hcd);
+ if (dum_hcd->rh_state == DUMMY_RH_RUNNING) {
dev_warn(&pdev->dev, "Root hub isn't suspended!\n");
rc = -EBUSY;
} else
@@ -1996,7 +2029,7 @@ static int __init init (void)
retval = platform_device_add(the_hcd_pdev);
if (retval < 0)
goto err_add_hcd;
- if (!the_controller) {
+ if (!the_controller.hs_hcd) {
/*
* The hcd was added successfully but its probe function failed
* for some reason.
--
1.7.3.3
--
Sent by an employee of the Qualcomm Innovation Center, Inc.
The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum.
^ permalink raw reply related [flat|nested] 13+ messages in thread* Re: [PATCH v11 6/7] usb:dummy_hcd: use the shared_hcd infrustructure
2011-05-19 11:43 ` [PATCH v11 6/7] usb:dummy_hcd: use the shared_hcd infrustructure Tatyana Brokhman
@ 2011-05-19 18:48 ` Alan Stern
0 siblings, 0 replies; 13+ messages in thread
From: Alan Stern @ 2011-05-19 18:48 UTC (permalink / raw)
To: Tatyana Brokhman; +Cc: greg, linux-usb, balbi, ablay, linux-arm-msm, open list
On Thu, 19 May 2011, Tatyana Brokhman wrote:
> This patch is a preparation for adding SuperSpeed support to dummy hcd.
> It takes the master side fields out of the struct dummy to a separate
> structure. The init process was also modified to resemble the way it is
> done by xHCI.
>
> Signed-off-by: Tatyana Brokhman <tlinder@codeaurora.org>
I have not checked this in detail, but right off the bat there are a
few stylistic issues.
BTW, splitting this up into two patches as Felipe suggested was a very
good idea.
> --- a/drivers/usb/gadget/dummy_hcd.c
> +++ b/drivers/usb/gadget/dummy_hcd.c
> @@ -152,6 +152,24 @@ enum dummy_rh_state {
> DUMMY_RH_RUNNING
> };
>
> +struct dummy_hcd {
> + struct usb_hcd *hcd;
What is this pointer for? It doesn't get used by the
dummy_hcd_to_hcd() routine, which means it shouldn't get used at all.
> +
> + struct dummy *dum;
> + enum dummy_rh_state rh_state;
> + struct timer_list timer;
> + u32 port_status;
> + u32 old_status;
> + unsigned resuming:1;
It's silly to have a bitfield in isolation like this -- you end up
wasting a bunch of space. Move this next to the other bitfields.
> + unsigned long re_timeout;
> +
> + struct usb_device *udev;
> + struct list_head urbp_list;
> +
> + unsigned active:1;
> + unsigned old_active:1;
> +};
> +
> struct dummy {
> spinlock_t lock;
>
> @@ -167,36 +185,26 @@ struct dummy {
> u16 devstatus;
> unsigned udc_suspended:1;
> unsigned pullup:1;
> - unsigned active:1;
> - unsigned old_active:1;
>
> /*
> * MASTER/HOST side support
> */
> - enum dummy_rh_state rh_state;
> - struct timer_list timer;
> - u32 port_status;
> - u32 old_status;
> - unsigned resuming:1;
> - unsigned long re_timeout;
> -
> - struct usb_device *udev;
> - struct list_head urbp_list;
> + struct dummy_hcd *hs_hcd;
You should use tabs to line up the columns with the existing entries.
Doesn't this look strange to you -- a single item in the middle of the
line by itself like that?
> };
>
> -static inline struct dummy *hcd_to_dummy (struct usb_hcd *hcd)
> +static inline struct dummy_hcd *hcd_to_dummy_hcd(struct usb_hcd *hcd)
> {
> - return (struct dummy *) (hcd->hcd_priv);
> + return (struct dummy_hcd *) (hcd->hcd_priv);
> }
>
> -static inline struct usb_hcd *dummy_to_hcd (struct dummy *dum)
> +static inline struct usb_hcd *dummy_hcd_to_hcd(struct dummy_hcd *dum)
> {
> return container_of((void *) dum, struct usb_hcd, hcd_priv);
> }
In several places you open-coded dummy_hcd_to_hcd(). Please change
them to use the inline routine instead.
> -static inline struct device *dummy_dev (struct dummy *dum)
> +static inline struct device *dummy_dev(struct dummy_hcd *dum)
> {
> - return dummy_to_hcd(dum)->self.controller;
> + return dummy_hcd_to_hcd(dum)->self.controller;
> }
You also open-coded this routine. It doesn't matter so much, but for
the sake of style you should use this inline routine too.
Alan Stern
^ permalink raw reply [flat|nested] 13+ messages in thread
* [PATCH v11 7/7] usb: Adding SuperSpeed support to dummy_hcd
[not found] <1305805417-31750-1-git-send-email-tlinder@codeaurora.org>
` (5 preceding siblings ...)
2011-05-19 11:43 ` [PATCH v11 6/7] usb:dummy_hcd: use the shared_hcd infrustructure Tatyana Brokhman
@ 2011-05-19 11:43 ` Tatyana Brokhman
6 siblings, 0 replies; 13+ messages in thread
From: Tatyana Brokhman @ 2011-05-19 11:43 UTC (permalink / raw)
To: greg; +Cc: linux-usb, balbi, ablay, linux-arm-msm, Tatyana Brokhman,
open list
This patch adds SS support to the dummy hcd module. It may be used to test
SS device when no (SS) HW is available.
USB 3.0 hub includes 2 hubs - HS and SS ones.
This patch adds support for a SS hub in the dummy_hcd module. Thus, when
dummy_hcd enabled it will register 2 root hubs (SS and HS).
Signed-off-by: Tatyana Brokhman <tlinder@codeaurora.org>
---
drivers/usb/gadget/dummy_hcd.c | 511 +++++++++++++++++++++++++++++++++++-----
1 files changed, 455 insertions(+), 56 deletions(-)
diff --git a/drivers/usb/gadget/dummy_hcd.c b/drivers/usb/gadget/dummy_hcd.c
index cf197e1..bebc08f 100644
--- a/drivers/usb/gadget/dummy_hcd.c
+++ b/drivers/usb/gadget/dummy_hcd.c
@@ -190,6 +190,7 @@ struct dummy {
* MASTER/HOST side support
*/
struct dummy_hcd *hs_hcd;
+ struct dummy_hcd *ss_hcd;
};
static inline struct dummy_hcd *hcd_to_dummy_hcd(struct usb_hcd *hcd)
@@ -220,7 +221,10 @@ static inline struct dummy *ep_to_dummy (struct dummy_ep *ep)
static inline struct dummy_hcd *gadget_to_dummy_hcd(struct usb_gadget *gadget)
{
struct dummy *dum = container_of(gadget, struct dummy, gadget);
- return dum->hs_hcd;
+ if (dum->gadget.speed == USB_SPEED_SUPER)
+ return dum->ss_hcd;
+ else
+ return dum->hs_hcd;
}
static inline struct dummy *gadget_dev_to_dummy (struct device *dev)
@@ -268,10 +272,86 @@ stop_activity (struct dummy *dum)
/* driver now does any non-usb quiescing necessary */
}
+/**
+ * set_ss_link_state() - Sets the current state of the SuperSpeed link
+ * @dum_hcd: pointer to the dummy_hcd structure to update the link
+ * state for
+ *
+ * This function updates the port_status according to the link
+ * state. The old status is saved befor updating.
+ * Note: this function should be called only for SuperSpeed
+ * master and the caller must hold the lock.
+ */
+static void
+set_ss_link_state(struct dummy_hcd *dum_hcd)
+{
+ struct dummy *dum = dum_hcd->dum;
+ dum_hcd->active = 0;
+ if ((dum_hcd->port_status & USB_SS_PORT_STAT_POWER) == 0)
+ dum_hcd->port_status = 0;
+
+ /* UDC suspend must cause a disconnect */
+ else if (!dum->pullup || dum->udc_suspended) {
+ dum_hcd->port_status &= ~(USB_PORT_STAT_CONNECTION |
+ USB_PORT_STAT_ENABLE);
+ if ((dum_hcd->old_status & USB_PORT_STAT_CONNECTION) != 0)
+ dum_hcd->port_status |=
+ (USB_PORT_STAT_C_CONNECTION << 16);
+ } else {
+ /* device is connected and not suspended */
+ dum_hcd->port_status |= (USB_PORT_STAT_CONNECTION |
+ USB_PORT_STAT_SPEED_5GBPS) ;
+ if ((dum_hcd->old_status & USB_PORT_STAT_CONNECTION) == 0)
+ dum_hcd->port_status |=
+ (USB_PORT_STAT_C_CONNECTION << 16);
+ if ((dum_hcd->port_status & USB_PORT_STAT_ENABLE) == 1 &&
+ (dum_hcd->port_status & USB_SS_PORT_LS_U0) == 1 &&
+ dum_hcd->rh_state != DUMMY_RH_SUSPENDED)
+ dum_hcd->active = 1;
+ }
+
+
+ if ((dum_hcd->port_status & USB_PORT_STAT_ENABLE) == 0 ||
+ dum_hcd->active)
+ dum_hcd->resuming = 0;
+
+ /* if !connected or reset */
+ if ((dum_hcd->port_status & USB_PORT_STAT_CONNECTION) == 0 ||
+ (dum_hcd->port_status & USB_PORT_STAT_RESET) != 0) {
+ /*
+ * We're connected and not reseted (reset occured now),
+ * and driver attached - disconnect!
+ */
+ if ((dum_hcd->old_status & USB_PORT_STAT_CONNECTION) != 0 &&
+ (dum_hcd->old_status & USB_PORT_STAT_RESET) == 0 &&
+ dum->driver) {
+ stop_activity(dum);
+ spin_unlock(&dum->lock);
+ dum->driver->disconnect(&dum->gadget);
+ spin_lock(&dum->lock);
+ }
+ } else if (dum_hcd->active != dum_hcd->old_active) {
+ if (dum_hcd->old_active && dum->driver->suspend) {
+ spin_unlock(&dum->lock);
+ dum->driver->suspend(&dum->gadget);
+ spin_lock(&dum->lock);
+ } else if (!dum_hcd->old_active && dum->driver->resume) {
+ spin_unlock(&dum->lock);
+ dum->driver->resume(&dum->gadget);
+ spin_lock(&dum->lock);
+ }
+ }
+
+ dum_hcd->old_status = dum_hcd->port_status;
+ dum_hcd->old_active = dum_hcd->active;
+}
+
/* caller must hold lock */
static void set_link_state(struct dummy_hcd *dum_hcd)
{
struct dummy *dum = dum_hcd->dum;
+ if (dum->gadget.speed == USB_SPEED_SUPER)
+ return;
dum_hcd->active = 0;
if ((dum_hcd->port_status & USB_PORT_STAT_POWER) == 0)
@@ -357,13 +437,17 @@ dummy_enable (struct usb_ep *_ep, const struct usb_endpoint_descriptor *desc)
dum = ep_to_dummy (ep);
if (!dum->driver)
return -ESHUTDOWN;
- dum_hcd = dum->hs_hcd;
+ if (dum->gadget.speed == USB_SPEED_SUPER)
+ dum_hcd = dum->ss_hcd;
+ else
+ dum_hcd = dum->hs_hcd;
if (!is_enabled(dum_hcd))
return -ESHUTDOWN;
/*
* For HS/FS devices only bits 0..10 of the wMaxPacketSize represent the
* maximum packet size.
+ * For SS devices the wMaxPacketSize is limited by 1024.
*/
max = le16_to_cpu(desc->wMaxPacketSize) & 0x7ff;
@@ -383,6 +467,10 @@ dummy_enable (struct usb_ep *_ep, const struct usb_endpoint_descriptor *desc)
goto done;
}
switch (dum->gadget.speed) {
+ case USB_SPEED_SUPER:
+ if (max == 1024)
+ break;
+ goto done;
case USB_SPEED_HIGH:
if (max == 512)
break;
@@ -401,6 +489,7 @@ dummy_enable (struct usb_ep *_ep, const struct usb_endpoint_descriptor *desc)
goto done;
/* real hardware might not handle all packet sizes */
switch (dum->gadget.speed) {
+ case USB_SPEED_SUPER:
case USB_SPEED_HIGH:
if (max <= 1024)
break;
@@ -421,6 +510,7 @@ dummy_enable (struct usb_ep *_ep, const struct usb_endpoint_descriptor *desc)
goto done;
/* real hardware might not handle all packet sizes */
switch (dum->gadget.speed) {
+ case USB_SPEED_SUPER:
case USB_SPEED_HIGH:
if (max <= 1024)
break;
@@ -541,7 +631,10 @@ dummy_queue (struct usb_ep *_ep, struct usb_request *_req,
return -EINVAL;
dum = ep_to_dummy (ep);
- dum_hcd = dum->hs_hcd;
+ if (dum->gadget.speed == USB_SPEED_SUPER)
+ dum_hcd = dum->ss_hcd;
+ else
+ dum_hcd = dum->hs_hcd;
if (!dum->driver || !is_enabled(dum_hcd))
return -ESHUTDOWN;
@@ -727,9 +820,13 @@ static int dummy_pullup (struct usb_gadget *_gadget, int value)
dum = gadget_to_dummy_hcd(_gadget)->dum;
spin_lock_irqsave (&dum->lock, flags);
dum->pullup = (value != 0);
- set_link_state(dum->hs_hcd);
+ if (dum->gadget.speed == USB_SPEED_SUPER)
+ set_ss_link_state(dum->ss_hcd);
+ else
+ set_link_state(dum->hs_hcd);
spin_unlock_irqrestore (&dum->lock, flags);
- usb_hcd_poll_rh_status(dum->hs_hcd->hcd);
+ usb_hcd_poll_rh_status((dum->gadget.speed == USB_SPEED_SUPER ?
+ dum->ss_hcd->hcd : dum->hs_hcd->hcd));
return 0;
}
@@ -810,8 +907,13 @@ usb_gadget_probe_driver(struct usb_gadget_driver *driver,
}
dum->gadget.ep0 = &dum->ep [0].ep;
- dum->gadget.speed = min((u8)driver->speed, (u8)USB_SPEED_HIGH) ;
- dum->ep[0].ep.maxpacket = 64;
+ dum->gadget.speed = driver->speed;
+ if (dum->gadget.speed == USB_SPEED_SUPER) {
+ for (i = 0; i < DUMMY_ENDPOINTS; i++)
+ dum->ep[i].ep.max_streams = 0x10;
+ dum->ep[0].ep.maxpacket = 9;
+ } else
+ dum->ep[0].ep.maxpacket = 64;
list_del_init (&dum->ep [0].ep.ep_list);
INIT_LIST_HEAD(&dum->fifo_req.queue);
@@ -830,11 +932,18 @@ usb_gadget_probe_driver(struct usb_gadget_driver *driver,
/* khubd will enumerate this in a while */
spin_lock_irq (&dum->lock);
dum->pullup = 1;
- dum->gadget.is_otg = (dum->hs_hcd->hcd->self.otg_port != 0);
- set_link_state(dum->hs_hcd);
+ if (dum->gadget.speed == USB_SPEED_SUPER) {
+ dum->gadget.is_otg = (dum->ss_hcd->hcd->self.otg_port != 0);
+ set_ss_link_state(dum->ss_hcd);
+ } else {
+ dum->gadget.is_otg = (dum->hs_hcd->hcd->self.otg_port != 0);
+ set_link_state(dum->hs_hcd);
+ }
+
spin_unlock_irq (&dum->lock);
- usb_hcd_poll_rh_status(dum->hs_hcd->hcd);
+ usb_hcd_poll_rh_status((dum->gadget.speed == USB_SPEED_SUPER ?
+ dum->ss_hcd->hcd : dum->hs_hcd->hcd));
return 0;
}
EXPORT_SYMBOL(usb_gadget_probe_driver);
@@ -855,18 +964,24 @@ usb_gadget_unregister_driver (struct usb_gadget_driver *driver)
spin_lock_irqsave (&dum->lock, flags);
dum->pullup = 0;
- set_link_state(dum->hs_hcd);
+ if (dum->gadget.speed == USB_SPEED_SUPER)
+ set_ss_link_state(dum->ss_hcd);
+ else
+ set_link_state(dum->hs_hcd);
spin_unlock_irqrestore (&dum->lock, flags);
driver->unbind (&dum->gadget);
dum->gadget.dev.driver = NULL;
dum->driver = NULL;
-
spin_lock_irqsave (&dum->lock, flags);
dum->pullup = 0;
- set_link_state(dum->hs_hcd);
+ if (dum->gadget.speed == USB_SPEED_SUPER)
+ set_ss_link_state(dum->ss_hcd);
+ else
+ set_link_state(dum->hs_hcd);
spin_unlock_irqrestore (&dum->lock, flags);
- usb_hcd_poll_rh_status(dum->hs_hcd->hcd);
+ usb_hcd_poll_rh_status((dum->gadget.speed == USB_SPEED_SUPER ?
+ dum->ss_hcd->hcd : dum->hs_hcd->hcd));
return 0;
}
EXPORT_SYMBOL (usb_gadget_unregister_driver);
@@ -934,10 +1049,14 @@ static int dummy_udc_suspend (struct platform_device *pdev, pm_message_t state)
dev_dbg (&pdev->dev, "%s\n", __func__);
spin_lock_irq (&dum->lock);
dum->udc_suspended = 1;
- set_link_state(dum->hs_hcd);
+ if (dum->gadget.speed == USB_SPEED_SUPER)
+ set_ss_link_state(dum->ss_hcd);
+ else
+ set_link_state(dum->hs_hcd);
spin_unlock_irq (&dum->lock);
- usb_hcd_poll_rh_status(dum->hs_hcd->hcd);
+ usb_hcd_poll_rh_status((dum->gadget.speed == USB_SPEED_SUPER ?
+ dum->ss_hcd->hcd : dum->hs_hcd->hcd));
return 0;
}
@@ -948,10 +1067,14 @@ static int dummy_udc_resume (struct platform_device *pdev)
dev_dbg (&pdev->dev, "%s\n", __func__);
spin_lock_irq (&dum->lock);
dum->udc_suspended = 0;
- set_link_state(dum->hs_hcd);
+ if (dum->gadget.speed == USB_SPEED_SUPER)
+ set_ss_link_state(dum->ss_hcd);
+ else
+ set_link_state(dum->hs_hcd);
spin_unlock_irq (&dum->lock);
- usb_hcd_poll_rh_status(dum->hs_hcd->hcd);
+ usb_hcd_poll_rh_status((dum->gadget.speed == USB_SPEED_SUPER ?
+ dum->ss_hcd->hcd : dum->hs_hcd->hcd));
return 0;
}
@@ -1179,6 +1302,21 @@ static int periodic_bytes (struct dummy *dum, struct dummy_ep *ep)
tmp *= 8 /* applies to entire frame */;
limit += limit * tmp;
}
+ if (dum->gadget.speed == USB_SPEED_SUPER) {
+ switch (ep->desc->bmAttributes & 0x03) {
+ case USB_ENDPOINT_XFER_ISOC:
+ /* Sec. 4.4.8.2 USB3.0 Spec */
+ limit = 3 * 16 * 1024 * 8;
+ break;
+ case USB_ENDPOINT_XFER_INT:
+ /* Sec. 4.4.7.2 USB3.0 Spec */
+ limit = 3 * 1024 * 8;
+ break;
+ case USB_ENDPOINT_XFER_BULK:
+ default:
+ break;
+ }
+ }
return limit;
}
@@ -1191,7 +1329,8 @@ static struct dummy_ep *find_endpoint (struct dummy *dum, u8 address)
{
int i;
- if (!is_active(dum->hs_hcd))
+ if (!is_active((dum->gadget.speed == USB_SPEED_SUPER ?
+ dum->ss_hcd : dum->hs_hcd)))
return NULL;
if ((address & ~USB_DIR_IN) == 0)
return &dum->ep [0];
@@ -1265,6 +1404,24 @@ static int handle_control_request(struct dummy_hcd *dum_hcd, struct urb *urb,
case USB_DEVICE_A_ALT_HNP_SUPPORT:
dum->gadget.a_alt_hnp_support = 1;
break;
+ case USB_DEVICE_U1_ENABLE:
+ if (dum_hcd->hcd->speed == HCD_USB3)
+ w_value = USB_DEV_STAT_U1_ENABLED;
+ else
+ ret_val = -EOPNOTSUPP;
+ break;
+ case USB_DEVICE_U2_ENABLE:
+ if (dum_hcd->hcd->speed == HCD_USB3)
+ w_value = USB_DEV_STAT_U2_ENABLED;
+ else
+ ret_val = -EOPNOTSUPP;
+ break;
+ case USB_DEVICE_LTM_ENABLE:
+ if (dum_hcd->hcd->speed == HCD_USB3)
+ w_value = USB_DEV_STAT_LTM_ENABLED;
+ else
+ ret_val = -EOPNOTSUPP;
+ break;
default:
ret_val = -EOPNOTSUPP;
}
@@ -1291,6 +1448,24 @@ static int handle_control_request(struct dummy_hcd *dum_hcd, struct urb *urb,
case USB_DEVICE_REMOTE_WAKEUP:
w_value = USB_DEVICE_REMOTE_WAKEUP;
break;
+ case USB_DEVICE_U1_ENABLE:
+ if (dum_hcd->hcd->speed == HCD_USB3)
+ w_value = USB_DEV_STAT_U1_ENABLED;
+ else
+ ret_val = -EOPNOTSUPP;
+ break;
+ case USB_DEVICE_U2_ENABLE:
+ if (dum_hcd->hcd->speed == HCD_USB3)
+ w_value = USB_DEV_STAT_U2_ENABLED;
+ else
+ ret_val = -EOPNOTSUPP;
+ break;
+ case USB_DEVICE_LTM_ENABLE:
+ if (dum_hcd->hcd->speed == HCD_USB3)
+ w_value = USB_DEV_STAT_LTM_ENABLED;
+ else
+ ret_val = -EOPNOTSUPP;
+ break;
default:
ret_val = -EOPNOTSUPP;
break;
@@ -1372,6 +1547,10 @@ static void dummy_timer(unsigned long _dum_hcd)
case USB_SPEED_HIGH:
total = 512/*bytes*/ * 13/*packets*/ * 8/*uframes*/;
break;
+ case USB_SPEED_SUPER:
+ /* Bus speed is 500000 bytes/ms, so use a little less */
+ total = 490000;
+ break;
default:
dev_err(dummy_dev(dum_hcd), "bogus device speed\n");
return;
@@ -1589,7 +1768,10 @@ static int dummy_hub_status (struct usb_hcd *hcd, char *buf)
if (dum_hcd->resuming && time_after_eq(jiffies, dum_hcd->re_timeout)) {
dum_hcd->port_status |= (USB_PORT_STAT_C_SUSPEND << 16);
dum_hcd->port_status &= ~USB_PORT_STAT_SUSPEND;
- set_link_state(dum_hcd);
+ if (dum_hcd->hcd->speed == HCD_USB3)
+ set_ss_link_state(dum_hcd);
+ else
+ set_link_state(dum_hcd);
}
if ((dum_hcd->port_status & PORT_C_MASK) != 0) {
@@ -1606,6 +1788,18 @@ done:
}
static inline void
+ss_hub_descriptor(struct usb_hub_descriptor *desc)
+{
+ memset(desc, 0, sizeof *desc);
+ desc->bDescriptorType = 0x2a;
+ desc->bDescLength = 12;
+ desc->wHubCharacteristics = cpu_to_le16(0x0001);
+ desc->bNbrPorts = 1;
+ desc->u.ss.bHubHdrDecLat = 0x04; /* Worst case: 0.4 micro sec*/
+ desc->u.ss.DeviceRemovable = 0xffff;
+}
+
+static inline void
hub_descriptor (struct usb_hub_descriptor *desc)
{
memset (desc, 0, sizeof *desc);
@@ -1641,6 +1835,12 @@ static int dummy_hub_control (
case ClearPortFeature:
switch (wValue) {
case USB_PORT_FEAT_SUSPEND:
+ if (hcd->speed == HCD_USB3) {
+ dev_dbg(dummy_dev(dum_hcd),
+ "USB_PORT_FEAT_SUSPEND req not "
+ "supported for USB 3.0 roothub\n");
+ goto error;
+ }
if (dum_hcd->port_status & USB_PORT_STAT_SUSPEND) {
/* 20msec resume signaling */
dum_hcd->resuming = 1;
@@ -1649,16 +1849,37 @@ static int dummy_hub_control (
}
break;
case USB_PORT_FEAT_POWER:
- if (dum_hcd->port_status & USB_PORT_STAT_POWER)
- dev_dbg(dummy_dev(dum_hcd), "power-off\n");
+ if (hcd->speed == HCD_USB3) {
+ if (dum_hcd->port_status & USB_PORT_STAT_POWER)
+ dev_dbg(dummy_dev(dum_hcd),
+ "power-off\n");
+ } else
+ if (dum_hcd->port_status &
+ USB_SS_PORT_STAT_POWER)
+ dev_dbg(dummy_dev(dum_hcd),
+ "power-off\n");
/* FALLS THROUGH */
default:
dum_hcd->port_status &= ~(1 << wValue);
- set_link_state(dum_hcd);
+ if (hcd->speed == HCD_USB3)
+ set_ss_link_state(dum_hcd);
+ else
+ set_link_state(dum_hcd);
}
break;
case GetHubDescriptor:
- hub_descriptor((struct usb_hub_descriptor *) buf);
+ if (hcd->speed == HCD_USB3 &&
+ (wLength < USB_DT_SS_HUB_SIZE ||
+ wValue != (USB_DT_SS_HUB << 8))) {
+ dev_dbg(dummy_dev(dum_hcd),
+ "Wrong hub descriptor type for "
+ "USB 3.0 roothub.\n");
+ goto error;
+ }
+ if (hcd->speed == HCD_USB3)
+ ss_hub_descriptor((struct usb_hub_descriptor *) buf);
+ else
+ hub_descriptor((struct usb_hub_descriptor *) buf);
break;
case GetHubStatus:
*(__le32 *) buf = cpu_to_le32 (0);
@@ -1681,25 +1902,31 @@ static int dummy_hub_control (
dum_hcd->port_status &= ~USB_PORT_STAT_RESET;
if (dum_hcd->dum->pullup) {
dum_hcd->port_status |= USB_PORT_STAT_ENABLE;
- switch (dum_hcd->dum->gadget.speed) {
- case USB_SPEED_HIGH:
- dum_hcd->port_status |=
- USB_PORT_STAT_HIGH_SPEED;
- break;
- case USB_SPEED_LOW:
- dum_hcd->dum->gadget.ep0->
- maxpacket = 8;
- dum_hcd->port_status |=
- USB_PORT_STAT_LOW_SPEED;
- break;
- default:
- dum_hcd->dum->gadget.speed =
- USB_SPEED_FULL;
- break;
+
+ if (hcd->speed < HCD_USB3) {
+ switch (dum_hcd->dum->gadget.speed) {
+ case USB_SPEED_HIGH:
+ dum_hcd->port_status |=
+ USB_PORT_STAT_HIGH_SPEED;
+ break;
+ case USB_SPEED_LOW:
+ dum_hcd->dum->gadget.ep0->
+ maxpacket = 8;
+ dum_hcd->port_status |=
+ USB_PORT_STAT_LOW_SPEED;
+ break;
+ default:
+ dum_hcd->dum->gadget.speed =
+ USB_SPEED_FULL;
+ break;
+ }
}
}
}
- set_link_state(dum_hcd);
+ if (hcd->speed == HCD_USB3)
+ set_ss_link_state(dum_hcd);
+ else
+ set_link_state(dum_hcd);
((__le16 *) buf)[0] = cpu_to_le16 (dum_hcd->port_status);
((__le16 *) buf)[1] = cpu_to_le16 (dum_hcd->port_status >> 16);
break;
@@ -1708,7 +1935,36 @@ static int dummy_hub_control (
break;
case SetPortFeature:
switch (wValue) {
+ case USB_PORT_FEAT_LINK_STATE:
+ if (hcd->speed != HCD_USB3) {
+ dev_dbg(dummy_dev(dum_hcd),
+ "USB_PORT_FEAT_LINK_STATE req not "
+ "supported for USB 2.0 roothub\n");
+ goto error;
+ }
+ /*
+ * Since this is dummy we don't have an actual link so
+ * there is nothing to do for the SET_LINK_STATE cmd
+ */
+ break;
+ case USB_PORT_FEAT_U1_TIMEOUT:
+ case USB_PORT_FEAT_U2_TIMEOUT:
+ /* TODO: add suspend/resume support! */
+ if (hcd->speed != HCD_USB3) {
+ dev_dbg(dummy_dev(dum_hcd),
+ "USB_PORT_FEAT_U1/2_TIMEOUT req not "
+ "supported for USB 2.0 roothub\n");
+ goto error;
+ }
+ break;
case USB_PORT_FEAT_SUSPEND:
+ /* Applicable only for USB2.0 hub */
+ if (hcd->speed == HCD_USB3) {
+ dev_dbg(dummy_dev(dum_hcd),
+ "USB_PORT_FEAT_SUSPEND req not "
+ "supported for USB 3.0 roothub\n");
+ goto error;
+ }
if (dum_hcd->active) {
dum_hcd->port_status |= USB_PORT_STAT_SUSPEND;
@@ -1723,12 +1979,33 @@ static int dummy_hub_control (
}
break;
case USB_PORT_FEAT_POWER:
- dum_hcd->port_status |= USB_PORT_STAT_POWER;
- set_link_state(dum_hcd);
+ if (hcd->speed == HCD_USB3) {
+ dum_hcd->port_status |= USB_SS_PORT_STAT_POWER;
+ set_ss_link_state(dum_hcd);
+ } else {
+ dum_hcd->port_status |= USB_PORT_STAT_POWER;
+ set_link_state(dum_hcd);
+ }
break;
+ case USB_PORT_FEAT_BH_PORT_RESET:
+ /* Applicable only for USB3.0 hub */
+ if (hcd->speed != HCD_USB3) {
+ dev_dbg(dummy_dev(dum_hcd),
+ "USB_PORT_FEAT_BH_PORT_RESET req not "
+ "supported for USB 2.0 roothub\n");
+ goto error;
+ }
+ /* FALLS THROUGH */
case USB_PORT_FEAT_RESET:
/* if it's already enabled, disable */
- dum_hcd->port_status &= ~(USB_PORT_STAT_ENABLE
+ if (hcd->speed == HCD_USB3) {
+ dum_hcd->port_status = 0;
+ dum_hcd->port_status =
+ (USB_SS_PORT_STAT_POWER |
+ USB_PORT_STAT_CONNECTION |
+ USB_PORT_STAT_RESET);
+ } else
+ dum_hcd->port_status &= ~(USB_PORT_STAT_ENABLE
| USB_PORT_STAT_LOW_SPEED
| USB_PORT_STAT_HIGH_SPEED);
/*
@@ -1737,21 +2014,50 @@ static int dummy_hub_control (
*/
dum_hcd->dum->devstatus &=
(1 << USB_DEVICE_SELF_POWERED);
+ /*
+ * FIXME USB3.0: what is the correct reset signaling
+ * interval? Is it still 50msec as for HS?
+ */
dum_hcd->re_timeout = jiffies + msecs_to_jiffies(50);
/* FALLS THROUGH */
default:
- if ((dum_hcd->port_status &
- USB_PORT_STAT_POWER) != 0) {
- dum_hcd->port_status |= (1 << wValue);
- set_link_state(dum_hcd);
- }
+ if (hcd->speed == HCD_USB3) {
+ if ((dum_hcd->port_status &
+ USB_SS_PORT_STAT_POWER) != 0) {
+ dum_hcd->port_status |= (1 << wValue);
+ set_ss_link_state(dum_hcd);
+ }
+ } else
+ if ((dum_hcd->port_status &
+ USB_PORT_STAT_POWER) != 0) {
+ dum_hcd->port_status |= (1 << wValue);
+ set_link_state(dum_hcd);
+ }
+ }
+ break;
+ case GetPortErrorCount:
+ if (hcd->speed != HCD_USB3) {
+ dev_dbg(dummy_dev(dum_hcd),
+ "GetPortErrorCount req not "
+ "supported for USB 2.0 roothub\n");
+ goto error;
+ }
+ /* We'll always return 0 since this is a dummy hub */
+ *(__le32 *) buf = cpu_to_le32(0);
+ break;
+ case SetHubDepth:
+ if (hcd->speed != HCD_USB3) {
+ dev_dbg(dummy_dev(dum_hcd),
+ "SetHubDepth req not supported for "
+ "USB 2.0 roothub\n");
+ goto error;
}
break;
-
default:
dev_dbg(dummy_dev(dum_hcd),
"hub control req%04x v%04x i%04x l%d\n",
typeReq, wValue, wIndex, wLength);
+error:
/* "protocol stall" on error */
retval = -EPIPE;
}
@@ -1770,7 +2076,10 @@ static int dummy_bus_suspend (struct usb_hcd *hcd)
spin_lock_irq(&dum_hcd->dum->lock);
dum_hcd->rh_state = DUMMY_RH_SUSPENDED;
- set_link_state(dum_hcd);
+ if (hcd->speed == HCD_USB3)
+ set_ss_link_state(dum_hcd);
+ else
+ set_link_state(dum_hcd);
hcd->state = HC_STATE_SUSPENDED;
spin_unlock_irq(&dum_hcd->dum->lock);
return 0;
@@ -1788,7 +2097,10 @@ static int dummy_bus_resume (struct usb_hcd *hcd)
rc = -ESHUTDOWN;
} else {
dum_hcd->rh_state = DUMMY_RH_RUNNING;
- set_link_state(dum_hcd);
+ if (hcd->speed == HCD_USB3)
+ set_ss_link_state(dum_hcd);
+ else
+ set_link_state(dum_hcd);
if (!list_empty(&dum_hcd->urbp_list))
mod_timer(&dum_hcd->timer, jiffies);
hcd->state = HC_STATE_RUNNING;
@@ -1812,6 +2124,9 @@ show_urb (char *buf, size_t size, struct urb *urb)
case USB_SPEED_LOW: s = "ls"; break;
case USB_SPEED_FULL: s = "fs"; break;
case USB_SPEED_HIGH: s = "hs"; break;
+ case USB_SPEED_SUPER:
+ s = "ss";
+ break;
default: s = "?"; break;
}; s; }),
ep, ep ? (usb_pipein (urb->pipe) ? "in" : "out") : "",
@@ -1848,6 +2163,26 @@ show_urbs (struct device *dev, struct device_attribute *attr, char *buf)
}
static DEVICE_ATTR (urbs, S_IRUGO, show_urbs, NULL);
+static int dummy_start_ss(struct dummy_hcd *dum_hcd)
+{
+ init_timer(&dum_hcd->timer);
+ dum_hcd->timer.function = dummy_timer;
+ dum_hcd->timer.data = (unsigned long)dum_hcd;
+ dum_hcd->rh_state = DUMMY_RH_RUNNING;
+ INIT_LIST_HEAD(&dum_hcd->urbp_list);
+ dum_hcd->hcd->power_budget = POWER_BUDGET;
+ dum_hcd->hcd->state = HC_STATE_RUNNING;
+ dum_hcd->hcd->uses_new_polling = 1;
+#ifdef CONFIG_USB_OTG
+ dum_hcd->hcd->self.otg_port = 1;
+#endif
+ return 0;
+
+ /* FIXME 'urbs' should be a per-device thing, maybe in usbcore */
+ return device_create_file(dum_hcd->hcd->self.controller,
+ &dev_attr_urbs);
+}
+
static int dummy_start(struct usb_hcd *hcd)
{
struct dummy_hcd *dum_hcd = hcd_to_dummy_hcd(hcd);
@@ -1857,6 +2192,9 @@ static int dummy_start(struct usb_hcd *hcd)
* talk to one device (the slave side). Also appears in sysfs,
* just like more familiar pci-based HCDs.
*/
+ if (!usb_hcd_is_primary_hcd(hcd))
+ return dummy_start_ss(dum_hcd);
+
spin_lock_init(&dum_hcd->dum->lock);
init_timer(&dum_hcd->timer);
dum_hcd->timer.function = dummy_timer;
@@ -1900,19 +2238,53 @@ static int dummy_setup(struct usb_hcd *hcd)
the_controller.hs_hcd = hcd_to_dummy_hcd(hcd);
the_controller.hs_hcd->hcd = hcd;
the_controller.hs_hcd->dum = &the_controller;
- /* Mark the first roothub as being USB 2.0. */
+ /*
+ * Mark the first roothub as being USB 2.0.
+ * The USB 3.0 roothub will be registered later by
+ * dummy_hcd_probe()
+ */
hcd->speed = HCD_USB2;
hcd->self.root_hub->speed = USB_SPEED_HIGH;
+ } else {
+ the_controller.ss_hcd = hcd_to_dummy_hcd(hcd);
+ the_controller.ss_hcd->hcd = hcd;
+ the_controller.ss_hcd->dum = &the_controller;
+ hcd->speed = HCD_USB3;
+ hcd->self.root_hub->speed = USB_SPEED_SUPER;
}
return 0;
}
+/* Change a group of bulk endpoints to support multiple stream IDs */
+int dummy_alloc_streams(struct usb_hcd *hcd, struct usb_device *udev,
+ struct usb_host_endpoint **eps, unsigned int num_eps,
+ unsigned int num_streams, gfp_t mem_flags)
+{
+ if (hcd->speed != HCD_USB3)
+ dev_dbg(dummy_dev(hcd_to_dummy_hcd(hcd)),
+ "%s() - ERROR! Not supported for USB2.0 roothub\n",
+ __func__);
+ return 0;
+}
+
+/* Reverts a group of bulk endpoints back to not using stream IDs. */
+int dummy_free_streams(struct usb_hcd *hcd, struct usb_device *udev,
+ struct usb_host_endpoint **eps, unsigned int num_eps,
+ gfp_t mem_flags)
+{
+ if (hcd->speed != HCD_USB3)
+ dev_dbg(dummy_dev(hcd_to_dummy_hcd(hcd)),
+ "%s() - ERROR! Not supported for USB2.0 roothub\n",
+ __func__);
+ return 0;
+}
+
static const struct hc_driver dummy_hcd = {
.description = (char *) driver_name,
.product_desc = "Dummy host controller",
.hcd_priv_size = sizeof(struct dummy_hcd),
- .flags = HCD_USB2,
+ .flags = HCD_USB3 | HCD_SHARED,
.reset = dummy_setup,
.start = dummy_start,
@@ -1927,11 +2299,15 @@ static const struct hc_driver dummy_hcd = {
.hub_control = dummy_hub_control,
.bus_suspend = dummy_bus_suspend,
.bus_resume = dummy_bus_resume,
+
+ .alloc_streams = dummy_alloc_streams,
+ .free_streams = dummy_free_streams,
};
static int dummy_hcd_probe(struct platform_device *pdev)
{
struct usb_hcd *hs_hcd;
+ struct usb_hcd *ss_hcd;
int retval;
dev_info(&pdev->dev, "%s, driver " DRIVER_VERSION "\n", driver_desc);
@@ -1943,8 +2319,27 @@ static int dummy_hcd_probe(struct platform_device *pdev)
retval = usb_add_hcd(hs_hcd, 0, 0);
if (retval != 0) {
usb_put_hcd(hs_hcd);
- the_controller.hs_hcd = NULL;
+ return retval;
+ }
+
+ ss_hcd = usb_create_shared_hcd(&dummy_hcd, &pdev->dev,
+ dev_name(&pdev->dev), hs_hcd);
+ if (!ss_hcd) {
+ retval = -ENOMEM;
+ goto dealloc_usb2_hcd;
}
+
+ retval = usb_add_hcd(ss_hcd, 0, 0);
+ if (retval)
+ goto put_usb3_hcd;
+
+ return 0;
+
+put_usb3_hcd:
+ usb_put_hcd(ss_hcd);
+dealloc_usb2_hcd:
+ usb_put_hcd(hs_hcd);
+ the_controller.hs_hcd = the_controller.ss_hcd = NULL;
return retval;
}
@@ -1953,9 +2348,13 @@ static int dummy_hcd_remove (struct platform_device *pdev)
struct dummy *dum;
dum = (hcd_to_dummy_hcd(platform_get_drvdata(pdev)))->dum;
+ if (dum->ss_hcd) {
+ usb_remove_hcd(dum->ss_hcd->hcd);
+ usb_put_hcd(dum->ss_hcd->hcd);
+ }
usb_remove_hcd(dum->hs_hcd->hcd);
usb_put_hcd(dum->hs_hcd->hcd);
- the_controller.hs_hcd = NULL;
+ the_controller.ss_hcd = the_controller.hs_hcd = NULL;
return 0;
}
@@ -2029,7 +2428,7 @@ static int __init init (void)
retval = platform_device_add(the_hcd_pdev);
if (retval < 0)
goto err_add_hcd;
- if (!the_controller.hs_hcd) {
+ if (!the_controller.hs_hcd || !the_controller.ss_hcd) {
/*
* The hcd was added successfully but its probe function failed
* for some reason.
--
1.7.3.3
--
Sent by an employee of the Qualcomm Innovation Center, Inc.
The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum.
^ permalink raw reply related [flat|nested] 13+ messages in thread