From: Axel Lin <axel.lin@gmail.com>
To: linux-kernel@vger.kernel.org
Cc: Laxman Dewangan <ldewangan@nvidia.com>,
Liam Girdwood <lrg@ti.com>,
Mark Brown <broonie@opensource.wolfsonmicro.com>
Subject: [PATCH RFT] regulator: rc5t583: Use generic regmap enable/disable operations
Date: Tue, 17 Apr 2012 14:11:31 +0800 [thread overview]
Message-ID: <1334643091.22780.2.camel@phoenix> (raw)
Signed-off-by: Axel Lin <axel.lin@gmail.com>
---
drivers/regulator/rc5t583-regulator.c | 63 +++-----------------------------
1 files changed, 6 insertions(+), 57 deletions(-)
diff --git a/drivers/regulator/rc5t583-regulator.c b/drivers/regulator/rc5t583-regulator.c
index b567c9e..81a74d1 100644
--- a/drivers/regulator/rc5t583-regulator.c
+++ b/drivers/regulator/rc5t583-regulator.c
@@ -37,8 +37,6 @@ struct rc5t583_regulator_info {
int deepsleep_id;
/* Regulator register address.*/
- uint8_t reg_en_reg;
- uint8_t en_bit;
uint8_t reg_disc_reg;
uint8_t disc_bit;
uint8_t vout_reg;
@@ -67,56 +65,6 @@ struct rc5t583_regulator {
struct regulator_dev *rdev;
};
-static int rc5t583_reg_is_enabled(struct regulator_dev *rdev)
-{
- struct rc5t583_regulator *reg = rdev_get_drvdata(rdev);
- struct rc5t583_regulator_info *ri = reg->reg_info;
- uint8_t control;
- int ret;
-
- ret = rc5t583_read(reg->mfd->dev, ri->reg_en_reg, &control);
- if (ret < 0) {
- dev_err(&rdev->dev,
- "Error in reading the control register 0x%02x\n",
- ri->reg_en_reg);
- return ret;
- }
- return !!(control & BIT(ri->en_bit));
-}
-
-static int rc5t583_reg_enable(struct regulator_dev *rdev)
-{
- struct rc5t583_regulator *reg = rdev_get_drvdata(rdev);
- struct rc5t583_regulator_info *ri = reg->reg_info;
- int ret;
-
- ret = rc5t583_set_bits(reg->mfd->dev, ri->reg_en_reg,
- (1 << ri->en_bit));
- if (ret < 0) {
- dev_err(&rdev->dev,
- "Error in setting bit of STATE register 0x%02x\n",
- ri->reg_en_reg);
- return ret;
- }
- return ret;
-}
-
-static int rc5t583_reg_disable(struct regulator_dev *rdev)
-{
- struct rc5t583_regulator *reg = rdev_get_drvdata(rdev);
- struct rc5t583_regulator_info *ri = reg->reg_info;
- int ret;
-
- ret = rc5t583_clear_bits(reg->mfd->dev, ri->reg_en_reg,
- (1 << ri->en_bit));
- if (ret < 0)
- dev_err(&rdev->dev,
- "Error in clearing bit of STATE register 0x%02x\n",
- ri->reg_en_reg);
-
- return ret;
-}
-
static int rc5t583_list_voltage(struct regulator_dev *rdev, unsigned selector)
{
struct rc5t583_regulator *reg = rdev_get_drvdata(rdev);
@@ -193,9 +141,9 @@ static int rc5t583_set_voltage_time_sel(struct regulator_dev *rdev,
static struct regulator_ops rc5t583_ops = {
- .is_enabled = rc5t583_reg_is_enabled,
- .enable = rc5t583_reg_enable,
- .disable = rc5t583_reg_disable,
+ .is_enabled = regulator_is_enabled_regmap,
+ .enable = regulator_enable_regmap,
+ .disable = regulator_disable_regmap,
.enable_time = rc5t583_regulator_enable_time,
.get_voltage_sel = rc5t583_get_voltage_sel,
.set_voltage = rc5t583_set_voltage,
@@ -206,8 +154,6 @@ static struct regulator_ops rc5t583_ops = {
#define RC5T583_REG(_id, _en_reg, _en_bit, _disc_reg, _disc_bit, \
_vout_mask, _min_mv, _max_mv, _step_uV, _enable_mv) \
{ \
- .reg_en_reg = RC5T583_REG_##_en_reg, \
- .en_bit = _en_bit, \
.reg_disc_reg = RC5T583_REG_##_disc_reg, \
.disc_bit = _disc_bit, \
.vout_reg = RC5T583_REG_##_id##DAC, \
@@ -226,6 +172,8 @@ static struct regulator_ops rc5t583_ops = {
.ops = &rc5t583_ops, \
.type = REGULATOR_VOLTAGE, \
.owner = THIS_MODULE, \
+ .enable_reg = RC5T583_REG_##_en_reg, \
+ .enable_mask = BIT(_en_bit), \
}, \
}
@@ -304,6 +252,7 @@ skip_ext_pwr_config:
config.dev = &pdev->dev;
config.init_data = reg_data;
config.driver_data = reg;
+ config.regmap = rc5t583->regmap;
rdev = regulator_register(&ri->desc, &config);
if (IS_ERR(rdev)) {
--
1.7.5.4
next reply other threads:[~2012-04-17 6:11 UTC|newest]
Thread overview: 2+ messages / expand[flat|nested] mbox.gz Atom feed top
2012-04-17 6:11 Axel Lin [this message]
2012-04-23 12:22 ` [PATCH RFT] regulator: rc5t583: Use generic regmap enable/disable operations Mark Brown
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1334643091.22780.2.camel@phoenix \
--to=axel.lin@gmail.com \
--cc=broonie@opensource.wolfsonmicro.com \
--cc=ldewangan@nvidia.com \
--cc=linux-kernel@vger.kernel.org \
--cc=lrg@ti.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox