[PATCH V4 13/16] MIPS: Loongson 3: Add Loongson-3 SMP support.

Huacai Chen
2012-08-03T07:08:53Z

IPI registers of Loongson-3 include IPI_SET, IPI_CLEAR, IPI_STATUS,
IPI_EN and IPI_MAILBOX_BUF. Each bit of IPI_STATUS indicate a type of
IPI and IPI_EN indicate whether the IPI is enabled. The sender write 1
to IPI_SET bits generate IPIs in IPI_STATUS, and receiver write 1 to
bits of IPI_CLEAR to clear IPIs. IPI_MAILBOX_BUF are used to deliver
more information about IPIs.

Why we change code in arch/mips/loongson/common/setup.c?

If without this change, when SMP configured, system cannot boot since
it hang at printk() in cgroup_init_early(). The root cause is:

console_trylock()
\-->down_trylock(&console_sem)
\-->raw_spin_unlock_irqrestore(&sem->lock, flags)
\-->_raw_spin_unlock_irqrestore()(SMP/UP have different versions)
\-->__raw_spin_unlock_irqrestore() (following is the SMP case)
\-->do_raw_spin_unlock()
\-->arch_spin_unlock()
\-->nudge_writes()
\-->mb()
\-->wbflush()
\-->__wbflush()

In previous code __wbflush() is initialized in plat_mem_setup(), but
cgroup_init_early() is called before plat_mem_setup(). Therefore, In
this patch we make changes to avoid boot failure.

Signed-off-by: Huacai Chen <chenhc@lemote.com>
Signed-off-by: Hongliang Tao <taohl@lemote.com>
Signed-off-by: Hua Yan <yanh@lemote.com>
---
arch/mips/loongson/common/init.c | 5 +
arch/mips/loongson/common/setup.c | 8 +-
arch/mips/loongson/loongson-3/Makefile | 2 +
arch/mips/loongson/loongson-3/smp.c | 278 ++++++++++++++++++++++++++++++++
arch/mips/loongson/loongson-3/smp.h | 24 +++
5 files changed, 312 insertions(+), 5 deletions(-)
create mode 100644 arch/mips/loongson/loongson-3/smp.c
create mode 100644 arch/mips/loongson/loongson-3/smp.h

diff --git a/arch/mips/loongson/common/init.c b/arch/mips/loongson/common/init.c
index 1c29b19..30d20ad 100644
--- a/arch/mips/loongson/common/init.c
+++ b/arch/mips/loongson/common/init.c
@@ -12,6 +12,8 @@

#include <loongson.h>

+extern struct plat_smp_ops loongson3_smp_ops;
+
/* Loongson CPU address windows config space base address */
unsigned long __maybe_unused _loongson_addrwincfg_base;

@@ -33,6 +35,9 @@ void __init prom_init(void)

/*init the uart base address */
prom_init_uart_base();
+#if defined(CONFIG_SMP)
+ register_smp_ops(&loongson3_smp_ops);
+#endif
}

void __init prom_free_prom_memory(void)
diff --git a/arch/mips/loongson/common/setup.c b/arch/mips/loongson/common/setup.c
index 27d826b..464cc5a 100644
--- a/arch/mips/loongson/common/setup.c
+++ b/arch/mips/loongson/common/setup.c
@@ -18,9 +18,6 @@
#include <linux/screen_info.h>
#endif

-void (*__wbflush)(void);
-EXPORT_SYMBOL(__wbflush);
-
static void wbflush_loongson(void)
{
asm(".set\tpush\n\t"
@@ -32,10 +29,11 @@ static void wbflush_loongson(void)
".set mips0\n\t");
}

+void (*__wbflush)(void) = wbflush_loongson;
+EXPORT_SYMBOL(__wbflush);
+
void __init plat_mem_setup(void)
{
- __wbflush = wbflush_loongson;
-
#ifdef CONFIG_VT
#if defined(CONFIG_VGA_CONSOLE)
conswitchp = &vga_con;
diff --git a/arch/mips/loongson/loongson-3/Makefile b/arch/mips/loongson/loongson-3/Makefile
index b9968cd..70152b2 100644
--- a/arch/mips/loongson/loongson-3/Makefile
+++ b/arch/mips/loongson/loongson-3/Makefile
@@ -2,3 +2,5 @@
# Makefile for Loongson-3 family machines
#
obj-y += irq.o
+
+obj-$(CONFIG_SMP) += smp.o
diff --git a/arch/mips/loongson/loongson-3/smp.c b/arch/mips/loongson/loongson-3/smp.c
new file mode 100644
index 0000000..30e7cb4
--- /dev/null
+++ b/arch/mips/loongson/loongson-3/smp.c
@@ -0,0 +1,278 @@
+/*
+ * Copyright (C) 2010, 2011, 2012, Lemote, Inc.
+ * Author: Chen Huacai, chenhc@lemote.com
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * as published by the Free Software Foundation; either version 2
+ * of the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place - Suite 330, Boston, MA 02111-1307, USA.
+ */
+
+#include <linux/init.h>
+#include <linux/cpu.h>
+#include <linux/sched.h>
+#include <linux/smp.h>
+#include <linux/cpufreq.h>
+#include <asm/processor.h>
+#include <asm/time.h>
+#include <asm/clock.h>
+#include <asm/tlbflush.h>
+#include <loongson.h>
+
+#include "smp.h"
+
+/* write a 64bit value to ipi register */
+void loongson3_ipi_write64(uint64_t action, void * addr)
+{
+ *((uint64_t *)addr) = action;
+};
+
+/* read a 64bit value from ipi register */
+uint64_t loongson3_ipi_read64(void * addr)
+{
+ return *((uint64_t *)addr);
+};
+
+/* write a 32bit value to ipi register */
+void loongson3_ipi_write32(uint32_t action, void * addr)
+{
+ *((uint32_t *)addr) = action;
+};
+
+/* read a 32bit value from ipi register */
+uint32_t loongson3_ipi_read32(void * addr)
+{
+ return *((uint32_t *)addr);
+};
+
+static void *ipi_set0_regs[] = {
+ (void *)(smp_core_group0_base + smp_core0_offset + SET0),
+ (void *)(smp_core_group0_base + smp_core1_offset + SET0),
+ (void *)(smp_core_group0_base + smp_core2_offset + SET0),
+ (void *)(smp_core_group0_base + smp_core3_offset + SET0),
+ (void *)(smp_core_group1_base + smp_core0_offset + SET0),
+ (void *)(smp_core_group1_base + smp_core1_offset + SET0),
+ (void *)(smp_core_group1_base + smp_core2_offset + SET0),
+ (void *)(smp_core_group1_base + smp_core3_offset + SET0),
+ (void *)(smp_core_group2_base + smp_core0_offset + SET0),
+ (void *)(smp_core_group2_base + smp_core1_offset + SET0),
+ (void *)(smp_core_group2_base + smp_core2_offset + SET0),
+ (void *)(smp_core_group2_base + smp_core3_offset + SET0),
+ (void *)(smp_core_group3_base + smp_core0_offset + SET0),
+ (void *)(smp_core_group3_base + smp_core1_offset + SET0),
+ (void *)(smp_core_group3_base + smp_core2_offset + SET0),
+ (void *)(smp_core_group3_base + smp_core3_offset + SET0),
+};
+
+static void *ipi_clear0_regs[] = {
+ (void *)(smp_core_group0_base + smp_core0_offset + CLEAR0),
+ (void *)(smp_core_group0_base + smp_core1_offset + CLEAR0),
+ (void *)(smp_core_group0_base + smp_core2_offset + CLEAR0),
+ (void *)(smp_core_group0_base + smp_core3_offset + CLEAR0),
+ (void *)(smp_core_group1_base + smp_core0_offset + CLEAR0),
+ (void *)(smp_core_group1_base + smp_core1_offset + CLEAR0),
+ (void *)(smp_core_group1_base + smp_core2_offset + CLEAR0),
+ (void *)(smp_core_group1_base + smp_core3_offset + CLEAR0),
+ (void *)(smp_core_group2_base + smp_core0_offset + CLEAR0),
+ (void *)(smp_core_group2_base + smp_core1_offset + CLEAR0),
+ (void *)(smp_core_group2_base + smp_core2_offset + CLEAR0),
+ (void *)(smp_core_group2_base + smp_core3_offset + CLEAR0),
+ (void *)(smp_core_group3_base + smp_core0_offset + CLEAR0),
+ (void *)(smp_core_group3_base + smp_core1_offset + CLEAR0),
+ (void *)(smp_core_group3_base + smp_core2_offset + CLEAR0),
+ (void *)(smp_core_group3_base + smp_core3_offset + CLEAR0),
+};
+
+static void *ipi_status_regs0[] = {
+ (void *)(smp_core_group0_base + smp_core0_offset + STATUS0),
+ (void *)(smp_core_group0_base + smp_core1_offset + STATUS0),
+ (void *)(smp_core_group0_base + smp_core2_offset + STATUS0),
+ (void *)(smp_core_group0_base + smp_core3_offset + STATUS0),
+ (void *)(smp_core_group1_base + smp_core0_offset + STATUS0),
+ (void *)(smp_core_group1_base + smp_core1_offset + STATUS0),
+ (void *)(smp_core_group1_base + smp_core2_offset + STATUS0),
+ (void *)(smp_core_group1_base + smp_core3_offset + STATUS0),
+ (void *)(smp_core_group2_base + smp_core0_offset + STATUS0),
+ (void *)(smp_core_group2_base + smp_core1_offset + STATUS0),
+ (void *)(smp_core_group2_base + smp_core2_offset + STATUS0),
+ (void *)(smp_core_group2_base + smp_core3_offset + STATUS0),
+ (void *)(smp_core_group3_base + smp_core0_offset + STATUS0),
+ (void *)(smp_core_group3_base + smp_core1_offset + STATUS0),
+ (void *)(smp_core_group3_base + smp_core2_offset + STATUS0),
+ (void *)(smp_core_group3_base + smp_core3_offset + STATUS0),
+};
+
+static void *ipi_en0_regs[] = {
+ (void *)(smp_core_group0_base + smp_core0_offset + EN0),
+ (void *)(smp_core_group0_base + smp_core1_offset + EN0),
+ (void *)(smp_core_group0_base + smp_core2_offset + EN0),
+ (void *)(smp_core_group0_base + smp_core3_offset + EN0),
+ (void *)(smp_core_group1_base + smp_core0_offset + EN0),
+ (void *)(smp_core_group1_base + smp_core1_offset + EN0),
+ (void *)(smp_core_group1_base + smp_core2_offset + EN0),
+ (void *)(smp_core_group1_base + smp_core3_offset + EN0),
+ (void *)(smp_core_group2_base + smp_core0_offset + EN0),
+ (void *)(smp_core_group2_base + smp_core1_offset + EN0),
+ (void *)(smp_core_group2_base + smp_core2_offset + EN0),
+ (void *)(smp_core_group2_base + smp_core3_offset + EN0),
+ (void *)(smp_core_group3_base + smp_core0_offset + EN0),
+ (void *)(smp_core_group3_base + smp_core1_offset + EN0),
+ (void *)(smp_core_group3_base + smp_core2_offset + EN0),
+ (void *)(smp_core_group3_base + smp_core3_offset + EN0),
+};
+
+static volatile void *ipi_mailbox_buf[] = {
+ (void *)(smp_core_group0_base + smp_core0_offset + BUF),
+ (void *)(smp_core_group0_base + smp_core1_offset + BUF),
+ (void *)(smp_core_group0_base + smp_core2_offset + BUF),
+ (void *)(smp_core_group0_base + smp_core3_offset + BUF),
+ (void *)(smp_core_group1_base + smp_core0_offset + BUF),
+ (void *)(smp_core_group1_base + smp_core1_offset + BUF),
+ (void *)(smp_core_group1_base + smp_core2_offset + BUF),
+ (void *)(smp_core_group1_base + smp_core3_offset + BUF),
+ (void *)(smp_core_group2_base + smp_core0_offset + BUF),
+ (void *)(smp_core_group2_base + smp_core1_offset + BUF),
+ (void *)(smp_core_group2_base + smp_core2_offset + BUF),
+ (void *)(smp_core_group2_base + smp_core3_offset + BUF),
+ (void *)(smp_core_group3_base + smp_core0_offset + BUF),
+ (void *)(smp_core_group3_base + smp_core1_offset + BUF),
+ (void *)(smp_core_group3_base + smp_core2_offset + BUF),
+ (void *)(smp_core_group3_base + smp_core3_offset + BUF),
+};
+
+/*
+ * Simple enough, just poke the appropriate ipi register
+ */
+static void loongson3_send_ipi_single(int cpu, unsigned int action)
+{
+ loongson3_ipi_write32((u32)action, ipi_set0_regs[cpu]);
+}
+
+static void loongson3_send_ipi_mask(const struct cpumask *mask, unsigned int action)
+{
+ unsigned int i;
+
+ for_each_cpu(i, mask)
+ loongson3_send_ipi_single(i, action);
+}
+
+void loongson3_ipi_interrupt(struct pt_regs *regs)
+{
+ int cpu = smp_processor_id();
+ unsigned int action;
+
+ /* Load the ipi register to figure out what we're supposed to do */
+ action = loongson3_ipi_read32(ipi_status_regs0[cpu]);
+
+ /* Clear the ipi register to clear the interrupt */
+ loongson3_ipi_write32((u32)action, ipi_clear0_regs[cpu]);
+
+ if (action & SMP_RESCHEDULE_YOURSELF) {
+ scheduler_ipi();
+ }
+
+ if (action & SMP_CALL_FUNCTION) {
+ smp_call_function_interrupt();
+ }
+}
+
+/*
+ * SMP init and finish on secondary CPUs
+ */
+void __cpuinit loongson3_init_secondary(void)
+{
+ int i;
+ unsigned int imask = STATUSF_IP7 | STATUSF_IP6 | STATUSF_IP5 |
+ STATUSF_IP4 | STATUSF_IP3 | STATUSF_IP2;
+
+ /* Set interrupt mask, but don't enable */
+ change_c0_status(ST0_IM, imask);
+
+ for (i = 0; i < NR_CPUS; i++) {
+ loongson3_ipi_write32(0xffffffff, ipi_en0_regs[i]);
+ }
+}
+
+void __cpuinit loongson3_smp_finish(void)
+{
+ write_c0_compare(read_c0_count() + mips_hpt_frequency/HZ);
+ local_irq_enable();
+ loongson3_ipi_write64(0, (void *)(ipi_mailbox_buf[smp_processor_id()]+0x0));
+ printk(KERN_INFO "CPU#%d finished, CP0_ST=%x\n",
+ smp_processor_id(), read_c0_status());
+}
+
+void __init loongson3_smp_setup(void)
+{
+ int i, num;
+
+ init_cpu_possible(cpu_none_mask);
+ set_cpu_possible(0, true);
+
+ __cpu_number_map[0] = 0;
+ __cpu_logical_map[0] = 0;
+
+ /* For unified kernel, NR_CPUS is the maximum possible value,
+ * nr_cpus_loongson is the really present value */
+ for (i = 1, num = 0; i < nr_cpus_loongson; i++) {
+ set_cpu_possible(i, true);
+ __cpu_number_map[i] = ++num;
+ __cpu_logical_map[num] = i;
+ }
+ printk(KERN_INFO "Detected %i available secondary CPU(s)\n", num);
+}
+
+void __init loongson3_prepare_cpus(unsigned int max_cpus)
+{
+}
+
+/*
+ * Setup the PC, SP, and GP of a secondary processor and start it runing!
+ */
+void __cpuinit loongson3_boot_secondary(int cpu, struct task_struct *idle)
+{
+ volatile unsigned long startargs[4];
+
+ printk(KERN_INFO "Booting CPU#%d...\n", cpu);
+
+ /* startargs[] are initial PC, SP and GP for secondary CPU */
+ startargs[0] = (unsigned long)&smp_bootstrap;
+ startargs[1] = (unsigned long)__KSTK_TOS(idle);
+ startargs[2] = (unsigned long)task_thread_info(idle);
+ startargs[3] = 0;
+
+ printk(KERN_DEBUG "CPU#%d, func_pc=%lx, sp=%lx, gp=%lx\n",
+ cpu, startargs[0], startargs[1], startargs[2]);
+
+ loongson3_ipi_write64(startargs[3], (void *)(ipi_mailbox_buf[cpu]+0x18));
+ loongson3_ipi_write64(startargs[2], (void *)(ipi_mailbox_buf[cpu]+0x10));
+ loongson3_ipi_write64(startargs[1], (void *)(ipi_mailbox_buf[cpu]+0x8));
+ loongson3_ipi_write64(startargs[0], (void *)(ipi_mailbox_buf[cpu]+0x0));
+}
+
+/*
+ * Final cleanup after all secondaries booted
+ */
+void __init loongson3_cpus_done(void)
+{
+}
+
+struct plat_smp_ops loongson3_smp_ops = {
+ .send_ipi_single = loongson3_send_ipi_single,
+ .send_ipi_mask = loongson3_send_ipi_mask,
+ .init_secondary = loongson3_init_secondary,
+ .smp_finish = loongson3_smp_finish,
+ .cpus_done = loongson3_cpus_done,
+ .boot_secondary = loongson3_boot_secondary,
+ .smp_setup = loongson3_smp_setup,
+ .prepare_cpus = loongson3_prepare_cpus,
+};
diff --git a/arch/mips/loongson/loongson-3/smp.h b/arch/mips/loongson/loongson-3/smp.h
new file mode 100644
index 0000000..dc9ce69
--- /dev/null
+++ b/arch/mips/loongson/loongson-3/smp.h
@@ -0,0 +1,24 @@
+/* for Loongson-3A smp support */
+
+/* 4 groups(nodes) in maximum in numa case */
+#define smp_core_group0_base 0x900000003ff01000
+#define smp_core_group1_base 0x900010003ff01000
+#define smp_core_group2_base 0x900020003ff01000
+#define smp_core_group3_base 0x900030003ff01000
+
+/* 4 cores in each group(node) */
+#define smp_core0_offset 0x000
+#define smp_core1_offset 0x100
+#define smp_core2_offset 0x200
+#define smp_core3_offset 0x300
+
+/* ipi registers offsets */
+#define STATUS0 0x00
+#define EN0 0x04
+#define SET0 0x08
+#define CLEAR0 0x0c
+#define STATUS1 0x10
+#define MASK1 0x14
+#define SET1 0x18
+#define CLEAR1 0x1c
+#define BUF 0x20
--
1.7.7.3