From: Axel Lin <axel.lin@ingics.com>
To: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: Thomas Abraham <thomas.abraham@linaro.org>,
Kyungmin Park <kyungmin.park@samsung.com>,
MyungJoo Ham <myungjoo.ham@samsung.com>,
Liam Girdwood <lrg@ti.com>,
linux-kernel@vger.kernel.org
Subject: [PATCH 1/3] regulator: max8997: Use uV in voltage_map_desc
Date: Fri, 28 Dec 2012 17:09:03 +0800 [thread overview]
Message-ID: <1356685743.27172.2.camel@phoenix> (raw)
Current code does integer division (min_vol = min_uV / 1000) before pass
min_vol to max8997_get_voltage_proper_val().
So it is possible min_vol is truncated to a smaller value.
For example, if the request min_uV is 800900 for ldo.
min_vol = 800900 / 1000 = 800 (mV)
Then max8997_get_voltage_proper_val returns 800 mV for this case which is lower
than the requested voltage.
Use uV rather than mV in voltage_map_desc to prevent truncation by integer
division.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
---
drivers/regulator/max8997.c | 36 +++++++++++++++++-------------------
1 file changed, 17 insertions(+), 19 deletions(-)
diff --git a/drivers/regulator/max8997.c b/drivers/regulator/max8997.c
index c30424a..1a1ae99 100644
--- a/drivers/regulator/max8997.c
+++ b/drivers/regulator/max8997.c
@@ -78,26 +78,26 @@ struct voltage_map_desc {
int step;
};
-/* Voltage maps in mV */
+/* Voltage maps in uV */
static const struct voltage_map_desc ldo_voltage_map_desc = {
- .min = 800, .max = 3950, .step = 50,
+ .min = 800000, .max = 3950000, .step = 50000,
}; /* LDO1 ~ 18, 21 all */
static const struct voltage_map_desc buck1245_voltage_map_desc = {
- .min = 650, .max = 2225, .step = 25,
+ .min = 650000, .max = 2225000, .step = 25000,
}; /* Buck1, 2, 4, 5 */
static const struct voltage_map_desc buck37_voltage_map_desc = {
- .min = 750, .max = 3900, .step = 50,
+ .min = 750000, .max = 3900000, .step = 50000,
}; /* Buck3, 7 */
-/* current map in mA */
+/* current map in uA */
static const struct voltage_map_desc charger_current_map_desc = {
- .min = 200, .max = 950, .step = 50,
+ .min = 200000, .max = 950000, .step = 50000,
};
static const struct voltage_map_desc topoff_current_map_desc = {
- .min = 50, .max = 200, .step = 10,
+ .min = 50000, .max = 200000, .step = 10000,
};
static const struct voltage_map_desc *reg_voltage_map[] = {
@@ -178,7 +178,7 @@ static int max8997_list_voltage(struct regulator_dev *rdev,
if (val > desc->max)
return -EINVAL;
- return val * 1000;
+ return val;
}
static int max8997_get_enable_register(struct regulator_dev *rdev,
@@ -469,7 +469,6 @@ static int max8997_set_voltage_ldobuck(struct regulator_dev *rdev,
{
struct max8997_data *max8997 = rdev_get_drvdata(rdev);
struct i2c_client *i2c = max8997->iodev->i2c;
- int min_vol = min_uV / 1000, max_vol = max_uV / 1000;
const struct voltage_map_desc *desc;
int rid = rdev_get_id(rdev);
int i, reg, shift, mask, ret;
@@ -493,7 +492,7 @@ static int max8997_set_voltage_ldobuck(struct regulator_dev *rdev,
desc = reg_voltage_map[rid];
- i = max8997_get_voltage_proper_val(desc, min_vol, max_vol);
+ i = max8997_get_voltage_proper_val(desc, min_uV, max_uV);
if (i < 0)
return i;
@@ -541,7 +540,7 @@ static int max8997_set_voltage_buck_time_sel(struct regulator_dev *rdev,
case MAX8997_BUCK4:
case MAX8997_BUCK5:
return DIV_ROUND_UP(desc->step * (new_selector - old_selector),
- max8997->ramp_delay);
+ max8997->ramp_delay * 1000);
}
return 0;
@@ -640,7 +639,6 @@ static int max8997_set_voltage_buck(struct regulator_dev *rdev,
const struct voltage_map_desc *desc;
int new_val, new_idx, damage, tmp_val, tmp_idx, tmp_dmg;
bool gpio_dvs_mode = false;
- int min_vol = min_uV / 1000, max_vol = max_uV / 1000;
if (rid < MAX8997_BUCK1 || rid > MAX8997_BUCK7)
return -EINVAL;
@@ -665,7 +663,7 @@ static int max8997_set_voltage_buck(struct regulator_dev *rdev,
selector);
desc = reg_voltage_map[rid];
- new_val = max8997_get_voltage_proper_val(desc, min_vol, max_vol);
+ new_val = max8997_get_voltage_proper_val(desc, min_uV, max_uV);
if (new_val < 0)
return new_val;
@@ -1080,8 +1078,8 @@ static int max8997_pmic_probe(struct platform_device *pdev)
max8997->buck1_vol[i] = ret =
max8997_get_voltage_proper_val(
&buck1245_voltage_map_desc,
- pdata->buck1_voltage[i] / 1000,
- pdata->buck1_voltage[i] / 1000 +
+ pdata->buck1_voltage[i],
+ pdata->buck1_voltage[i] +
buck1245_voltage_map_desc.step);
if (ret < 0)
goto err_out;
@@ -1089,8 +1087,8 @@ static int max8997_pmic_probe(struct platform_device *pdev)
max8997->buck2_vol[i] = ret =
max8997_get_voltage_proper_val(
&buck1245_voltage_map_desc,
- pdata->buck2_voltage[i] / 1000,
- pdata->buck2_voltage[i] / 1000 +
+ pdata->buck2_voltage[i],
+ pdata->buck2_voltage[i] +
buck1245_voltage_map_desc.step);
if (ret < 0)
goto err_out;
@@ -1098,8 +1096,8 @@ static int max8997_pmic_probe(struct platform_device *pdev)
max8997->buck5_vol[i] = ret =
max8997_get_voltage_proper_val(
&buck1245_voltage_map_desc,
- pdata->buck5_voltage[i] / 1000,
- pdata->buck5_voltage[i] / 1000 +
+ pdata->buck5_voltage[i],
+ pdata->buck5_voltage[i] +
buck1245_voltage_map_desc.step);
if (ret < 0)
goto err_out;
--
1.7.9.5
next reply other threads:[~2012-12-28 9:09 UTC|newest]
Thread overview: 6+ messages / expand[flat|nested] mbox.gz Atom feed top
2012-12-28 9:09 Axel Lin [this message]
2012-12-28 9:10 ` [PATCH 2/3] regulator: max8998: Use uV in voltage_map_desc Axel Lin
2013-01-08 11:16 ` Mark Brown
2012-12-28 9:14 ` [PATCH 3/3] regulator: max8998: Return enough delay time for max8998_set_voltage_buck_time_sel Axel Lin
2013-01-08 11:18 ` Mark Brown
2013-01-08 11:14 ` [PATCH 1/3] regulator: max8997: Use uV in voltage_map_desc Mark Brown
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1356685743.27172.2.camel@phoenix \
--to=axel.lin@ingics.com \
--cc=broonie@opensource.wolfsonmicro.com \
--cc=kyungmin.park@samsung.com \
--cc=linux-kernel@vger.kernel.org \
--cc=lrg@ti.com \
--cc=myungjoo.ham@samsung.com \
--cc=thomas.abraham@linaro.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox