From: Lee Jones <lee.jones@linaro.org>
To: linux-arm-kernel@lists.infradead.org, linux-kernel@vger.kernel.org
Cc: arnd@arndb.de, linus.walleij@stericsson.com,
srinidhi.kasagar@stericsson.com, Lee Jones <lee.jones@linaro.org>,
Vinod Koul <vinod.koul@intel.com>, Dan Williams <djbw@fb.com>,
Per Forlin <per.forlin@stericsson.com>,
Rabin Vincent <rabin@rab.in>
Subject: [PATCH 55/63] dmaengine: ste_dma40: Replace ST-E's home-brew DMA direction defs with generic ones
Date: Fri, 3 May 2013 15:32:41 +0100 [thread overview]
Message-ID: <1367591569-32197-56-git-send-email-lee.jones@linaro.org> (raw)
In-Reply-To: <1367591569-32197-1-git-send-email-lee.jones@linaro.org>
STEDMA40_*_TO_* direction definitions are identical in all but name to
the pre-defined generic DMA_*_TO_* ones. Let's make things easy by not
duplicating such things.
Cc: Vinod Koul <vinod.koul@intel.com>
Cc: Dan Williams <djbw@fb.com>
Cc: Per Forlin <per.forlin@stericsson.com>
Cc: Rabin Vincent <rabin@rab.in>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
---
drivers/dma/ste_dma40.c | 56 ++++++++++++++++++++++----------------------
drivers/dma/ste_dma40_ll.c | 24 +++++++++----------
2 files changed, 40 insertions(+), 40 deletions(-)
diff --git a/drivers/dma/ste_dma40.c b/drivers/dma/ste_dma40.c
index 8e7fa9d..78aeaa7 100644
--- a/drivers/dma/ste_dma40.c
+++ b/drivers/dma/ste_dma40.c
@@ -64,7 +64,7 @@ static int dma40_memcpy_channels[] = { 56, 57, 58, 59, 60 };
/* Default configuration for physcial memcpy */
struct stedma40_chan_cfg dma40_memcpy_conf_phy = {
.mode = STEDMA40_MODE_PHYSICAL,
- .dir = STEDMA40_MEM_TO_MEM,
+ .dir = DMA_MEM_TO_MEM,
.src_info.data_width = STEDMA40_BYTE_WIDTH,
.src_info.psize = STEDMA40_PSIZE_PHY_1,
@@ -78,7 +78,7 @@ struct stedma40_chan_cfg dma40_memcpy_conf_phy = {
/* Default configuration for logical memcpy */
struct stedma40_chan_cfg dma40_memcpy_conf_log = {
.mode = STEDMA40_MODE_LOGICAL,
- .dir = STEDMA40_MEM_TO_MEM,
+ .dir = DMA_MEM_TO_MEM,
.src_info.data_width = STEDMA40_BYTE_WIDTH,
.src_info.psize = STEDMA40_PSIZE_LOG_1,
@@ -829,7 +829,7 @@ static void d40_log_lli_to_lcxa(struct d40_chan *chan, struct d40_desc *desc)
* that uses linked lists.
*/
if (!(chan->phy_chan->use_soft_lli &&
- chan->dma_cfg.dir == STEDMA40_PERIPH_TO_MEM))
+ chan->dma_cfg.dir == DMA_DEV_TO_MEM))
curr_lcla = d40_lcla_alloc_one(chan, desc);
first_lcla = curr_lcla;
@@ -1297,12 +1297,12 @@ static void d40_config_set_event(struct d40_chan *d40c,
u32 event = D40_TYPE_TO_EVENT(d40c->dma_cfg.dev_type);
/* Enable event line connected to device (or memcpy) */
- if ((d40c->dma_cfg.dir == STEDMA40_PERIPH_TO_MEM) ||
- (d40c->dma_cfg.dir == STEDMA40_PERIPH_TO_PERIPH))
+ if ((d40c->dma_cfg.dir == DMA_DEV_TO_MEM) ||
+ (d40c->dma_cfg.dir == DMA_DEV_TO_DEV))
__d40_config_set_event(d40c, event_type, event,
D40_CHAN_REG_SSLNK);
- if (d40c->dma_cfg.dir != STEDMA40_PERIPH_TO_MEM)
+ if (d40c->dma_cfg.dir != DMA_DEV_TO_MEM)
__d40_config_set_event(d40c, event_type, event,
D40_CHAN_REG_SDLNK);
}
@@ -1760,7 +1760,7 @@ static int d40_validate_conf(struct d40_chan *d40c,
res = -EINVAL;
}
- if (conf->dir == STEDMA40_PERIPH_TO_PERIPH) {
+ if (conf->dir == DMA_DEV_TO_DEV) {
/*
* DMAC HW supports it. Will be added to this driver,
* in case any dma client requires it.
@@ -1891,11 +1891,11 @@ static int d40_allocate_channel(struct d40_chan *d40c, bool *first_phy_user)
phys = d40c->base->phy_res;
num_phy_chans = d40c->base->num_phy_chans;
- if (d40c->dma_cfg.dir == STEDMA40_PERIPH_TO_MEM) {
+ if (d40c->dma_cfg.dir == DMA_DEV_TO_MEM) {
log_num = 2 * dev_type;
is_src = true;
- } else if (d40c->dma_cfg.dir == STEDMA40_MEM_TO_PERIPH ||
- d40c->dma_cfg.dir == STEDMA40_MEM_TO_MEM) {
+ } else if (d40c->dma_cfg.dir == DMA_MEM_TO_DEV ||
+ d40c->dma_cfg.dir == DMA_MEM_TO_MEM) {
/* dst event lines are used for logical memcpy */
log_num = 2 * dev_type + 1;
is_src = false;
@@ -1906,7 +1906,7 @@ static int d40_allocate_channel(struct d40_chan *d40c, bool *first_phy_user)
event_line = D40_TYPE_TO_EVENT(dev_type);
if (!is_log) {
- if (d40c->dma_cfg.dir == STEDMA40_MEM_TO_MEM) {
+ if (d40c->dma_cfg.dir == DMA_MEM_TO_MEM) {
/* Find physical half channel */
if (d40c->dma_cfg.use_fixed_channel) {
i = d40c->dma_cfg.phy_channel;
@@ -2054,10 +2054,10 @@ static int d40_free_dma(struct d40_chan *d40c)
return -EINVAL;
}
- if (d40c->dma_cfg.dir == STEDMA40_MEM_TO_PERIPH ||
- d40c->dma_cfg.dir == STEDMA40_MEM_TO_MEM)
+ if (d40c->dma_cfg.dir == DMA_MEM_TO_DEV ||
+ d40c->dma_cfg.dir == DMA_MEM_TO_MEM)
is_src = false;
- else if (d40c->dma_cfg.dir == STEDMA40_PERIPH_TO_MEM)
+ else if (d40c->dma_cfg.dir == DMA_DEV_TO_MEM)
is_src = true;
else {
chan_err(d40c, "Unknown direction\n");
@@ -2119,10 +2119,10 @@ static bool d40_is_paused(struct d40_chan *d40c)
goto _exit;
}
- if (d40c->dma_cfg.dir == STEDMA40_MEM_TO_PERIPH ||
- d40c->dma_cfg.dir == STEDMA40_MEM_TO_MEM) {
+ if (d40c->dma_cfg.dir == DMA_MEM_TO_DEV ||
+ d40c->dma_cfg.dir == DMA_MEM_TO_MEM) {
status = readl(chanbase + D40_CHAN_REG_SDLNK);
- } else if (d40c->dma_cfg.dir == STEDMA40_PERIPH_TO_MEM) {
+ } else if (d40c->dma_cfg.dir == DMA_DEV_TO_MEM) {
status = readl(chanbase + D40_CHAN_REG_SSLNK);
} else {
chan_err(d40c, "Unknown direction\n");
@@ -2373,12 +2373,12 @@ static void d40_set_prio_realtime(struct d40_chan *d40c)
if (d40c->base->rev < 3)
return;
- if ((d40c->dma_cfg.dir == STEDMA40_PERIPH_TO_MEM) ||
- (d40c->dma_cfg.dir == STEDMA40_PERIPH_TO_PERIPH))
+ if ((d40c->dma_cfg.dir == DMA_DEV_TO_MEM) ||
+ (d40c->dma_cfg.dir == DMA_DEV_TO_DEV))
__d40_set_prio_rt(d40c, d40c->dma_cfg.dev_type, true);
- if ((d40c->dma_cfg.dir == STEDMA40_MEM_TO_PERIPH) ||
- (d40c->dma_cfg.dir == STEDMA40_PERIPH_TO_PERIPH))
+ if ((d40c->dma_cfg.dir == DMA_MEM_TO_DEV) ||
+ (d40c->dma_cfg.dir == DMA_DEV_TO_DEV))
__d40_set_prio_rt(d40c, d40c->dma_cfg.dev_type, false);
}
@@ -2409,11 +2409,11 @@ static struct dma_chan *d40_xlate(struct of_phandle_args *dma_spec,
switch (D40_DT_FLAGS_DIR(flags)) {
case 0:
- cfg.dir = STEDMA40_MEM_TO_PERIPH;
+ cfg.dir = DMA_MEM_TO_DEV;
cfg.dst_info.big_endian = D40_DT_FLAGS_BIG_ENDIAN(flags);
break;
case 1:
- cfg.dir = STEDMA40_PERIPH_TO_MEM;
+ cfg.dir = DMA_DEV_TO_MEM;
cfg.src_info.big_endian = D40_DT_FLAGS_BIG_ENDIAN(flags);
break;
}
@@ -2459,7 +2459,7 @@ static int d40_alloc_chan_resources(struct dma_chan *chan)
d40_set_prio_realtime(d40c);
if (chan_is_logical(d40c)) {
- if (d40c->dma_cfg.dir == STEDMA40_PERIPH_TO_MEM)
+ if (d40c->dma_cfg.dir == DMA_DEV_TO_MEM)
d40c->lcpa = d40c->base->lcpa_base +
d40c->dma_cfg.dev_type * D40_LCPA_CHAN_SIZE;
else
@@ -2732,12 +2732,12 @@ static int d40_set_runtime_config(struct dma_chan *chan,
if (config->direction == DMA_DEV_TO_MEM) {
config_addr = config->src_addr;
- if (cfg->dir != STEDMA40_PERIPH_TO_MEM)
+ if (cfg->dir != DMA_DEV_TO_MEM)
dev_dbg(d40c->base->dev,
"channel was not configured for peripheral "
"to memory transfer (%d) overriding\n",
cfg->dir);
- cfg->dir = STEDMA40_PERIPH_TO_MEM;
+ cfg->dir = DMA_DEV_TO_MEM;
/* Configure the memory side */
if (dst_addr_width == DMA_SLAVE_BUSWIDTH_UNDEFINED)
@@ -2748,12 +2748,12 @@ static int d40_set_runtime_config(struct dma_chan *chan,
} else if (config->direction == DMA_MEM_TO_DEV) {
config_addr = config->dst_addr;
- if (cfg->dir != STEDMA40_MEM_TO_PERIPH)
+ if (cfg->dir != DMA_MEM_TO_DEV)
dev_dbg(d40c->base->dev,
"channel was not configured for memory "
"to peripheral transfer (%d) overriding\n",
cfg->dir);
- cfg->dir = STEDMA40_MEM_TO_PERIPH;
+ cfg->dir = DMA_MEM_TO_DEV;
/* Configure the memory side */
if (src_addr_width == DMA_SLAVE_BUSWIDTH_UNDEFINED)
diff --git a/drivers/dma/ste_dma40_ll.c b/drivers/dma/ste_dma40_ll.c
index ab5a2a7..121c0ce 100644
--- a/drivers/dma/ste_dma40_ll.c
+++ b/drivers/dma/ste_dma40_ll.c
@@ -18,23 +18,23 @@ void d40_log_cfg(struct stedma40_chan_cfg *cfg,
u32 l1 = 0; /* src */
/* src is mem? -> increase address pos */
- if (cfg->dir == STEDMA40_MEM_TO_PERIPH ||
- cfg->dir == STEDMA40_MEM_TO_MEM)
+ if (cfg->dir == DMA_MEM_TO_DEV ||
+ cfg->dir == DMA_MEM_TO_MEM)
l1 |= 1 << D40_MEM_LCSP1_SCFG_INCR_POS;
/* dst is mem? -> increase address pos */
- if (cfg->dir == STEDMA40_PERIPH_TO_MEM ||
- cfg->dir == STEDMA40_MEM_TO_MEM)
+ if (cfg->dir == DMA_DEV_TO_MEM ||
+ cfg->dir == DMA_MEM_TO_MEM)
l3 |= 1 << D40_MEM_LCSP3_DCFG_INCR_POS;
/* src is hw? -> master port 1 */
- if (cfg->dir == STEDMA40_PERIPH_TO_MEM ||
- cfg->dir == STEDMA40_PERIPH_TO_PERIPH)
+ if (cfg->dir == DMA_DEV_TO_MEM ||
+ cfg->dir == DMA_DEV_TO_DEV)
l1 |= 1 << D40_MEM_LCSP1_SCFG_MST_POS;
/* dst is hw? -> master port 1 */
- if (cfg->dir == STEDMA40_MEM_TO_PERIPH ||
- cfg->dir == STEDMA40_PERIPH_TO_PERIPH)
+ if (cfg->dir == DMA_MEM_TO_DEV ||
+ cfg->dir == DMA_DEV_TO_DEV)
l3 |= 1 << D40_MEM_LCSP3_DCFG_MST_POS;
l3 |= 1 << D40_MEM_LCSP3_DCFG_EIM_POS;
@@ -55,8 +55,8 @@ void d40_phy_cfg(struct stedma40_chan_cfg *cfg, u32 *src_cfg, u32 *dst_cfg)
u32 src = 0;
u32 dst = 0;
- if ((cfg->dir == STEDMA40_PERIPH_TO_MEM) ||
- (cfg->dir == STEDMA40_PERIPH_TO_PERIPH)) {
+ if ((cfg->dir == DMA_DEV_TO_MEM) ||
+ (cfg->dir == DMA_DEV_TO_DEV)) {
/* Set master port to 1 */
src |= 1 << D40_SREG_CFG_MST_POS;
src |= D40_TYPE_TO_EVENT(cfg->dev_type);
@@ -66,8 +66,8 @@ void d40_phy_cfg(struct stedma40_chan_cfg *cfg, u32 *src_cfg, u32 *dst_cfg)
else
src |= 3 << D40_SREG_CFG_PHY_TM_POS;
}
- if ((cfg->dir == STEDMA40_MEM_TO_PERIPH) ||
- (cfg->dir == STEDMA40_PERIPH_TO_PERIPH)) {
+ if ((cfg->dir == DMA_MEM_TO_DEV) ||
+ (cfg->dir == DMA_DEV_TO_DEV)) {
/* Set master port to 1 */
dst |= 1 << D40_SREG_CFG_MST_POS;
dst |= D40_TYPE_TO_EVENT(cfg->dev_type);
--
1.7.10.4
next prev parent reply other threads:[~2013-05-03 14:38 UTC|newest]
Thread overview: 119+ messages / expand[flat|nested] mbox.gz Atom feed top
2013-05-03 14:31 [PATCH 00/63] dmaengine: Convert to correct API & Device Tree handling Lee Jones
2013-05-03 14:31 ` [PATCH 01/63] ARM: ux500: Supply address location names for the DMA40 DMA controller Lee Jones
2013-05-03 19:27 ` Linus Walleij
2013-05-03 14:31 ` [PATCH 02/63] ARM: ux500: Setup the DMA40 driver's DT node using the new DMA API Lee Jones
2013-05-03 19:29 ` Linus Walleij
2013-05-03 14:31 ` [PATCH 03/63] ARM: ux500: Supply UART's DMA configuration via Device Tree Lee Jones
2013-05-03 19:33 ` Linus Walleij
2013-05-03 14:31 ` [PATCH 04/63] ARM: ux500: Supply MMC " Lee Jones
2013-05-03 19:33 ` Linus Walleij
2013-05-03 14:31 ` [PATCH 05/63] ARM: ux500: Populate the ux500-musb Device Tree entry Lee Jones
2013-05-03 19:35 ` Linus Walleij
2013-05-03 14:31 ` [PATCH 06/63] ARM: ux500: Pass DMA memcpy channels though Device Tree Lee Jones
2013-05-03 19:37 ` Linus Walleij
2013-05-03 14:31 ` [PATCH 07/63] dmaengine: ste_dma40: Assign memcpy channels in the driver Lee Jones
2013-05-03 19:40 ` Linus Walleij
2013-05-03 19:51 ` Linus Walleij
2013-05-03 14:31 ` [PATCH 08/63] dmaengine: ste_dma40: Move default memcpy configs into " Lee Jones
2013-05-03 19:53 ` Linus Walleij
2013-05-03 14:31 ` [PATCH 09/63] dmaengine: ste_dma40: Rectify incorrect configuration validation checking Lee Jones
2013-05-03 19:58 ` Linus Walleij
2013-05-20 12:36 ` Linus Walleij
2013-05-03 14:31 ` [PATCH 10/63] dmaengine: ste_dma40: Amalgamate DMA source and destination channel numbers Lee Jones
2013-05-03 20:00 ` Linus Walleij
2013-05-20 12:35 ` Linus Walleij
2013-05-23 10:46 ` Vinod Koul
2013-05-03 14:31 ` [PATCH 11/63] ARM: ux500: Strip out duplicate USB DMA configuration Lee Jones
2013-05-03 20:02 ` Linus Walleij
2013-05-03 14:31 ` [PATCH 12/63] dmaengine: ste_dma40: Remove home-brew MAX() macro Lee Jones
2013-05-03 20:04 ` Linus Walleij
2013-05-20 12:32 ` Linus Walleij
2013-05-03 14:31 ` [PATCH 13/63] ARM: ux500: Remove unused 'data_width' attributes from SDI DMA configs Lee Jones
2013-05-03 20:07 ` Linus Walleij
2013-05-03 14:32 ` [PATCH 14/63] ARM: ux500: Remove unused 'data_width' attributes from SSP " Lee Jones
2013-05-03 20:09 ` Linus Walleij
2013-05-03 14:32 ` [PATCH 15/63] ARM: ux500: Remove unused 'data_width' attributes from UART " Lee Jones
2013-05-03 20:11 ` Linus Walleij
2013-05-03 14:32 ` [PATCH 16/63] ARM: ux500: Remove superfluous 'psize' attribute from Audio platform data Lee Jones
2013-05-03 20:13 ` Linus Walleij
2013-05-03 20:59 ` Fabio Baltieri
2013-05-03 21:04 ` Linus Walleij
2013-05-03 14:32 ` [PATCH 17/63] dmaengine: ste_dma40: Calculate number of logical channels from physical ones Lee Jones
2013-05-03 20:15 ` Linus Walleij
2013-05-03 14:32 ` [PATCH 18/63] dmaengine: ste_dma40: Remove 'always true' checking Lee Jones
2013-05-03 20:17 ` Linus Walleij
2013-05-03 14:32 ` [PATCH 19/63] dmaengine: ste_dma40: Separate Logical Global Interrupt Mask (GIM) unmasking Lee Jones
2013-05-03 20:23 ` Linus Walleij
2013-05-08 15:02 ` Lee Jones
2013-05-03 14:32 ` [PATCH 20/63] dmaengine: ste_dma40: Remove unnecessary call to d40_phy_cfg() Lee Jones
2013-05-03 20:27 ` Linus Walleij
2013-05-08 15:20 ` Lee Jones
2013-05-03 14:32 ` [PATCH 21/63] dmaengine: ste_dma40: Don't configure runtime configurable setup during allocate Lee Jones
2013-05-03 20:41 ` Linus Walleij
2013-05-08 15:24 ` Lee Jones
2013-05-03 14:32 ` [PATCH 22/63] dmaengine: ste_dma40: Move rev error-check up to revision acquisition Lee Jones
2013-05-03 20:48 ` Linus Walleij
2013-05-03 14:32 ` [PATCH 23/63] dmaengine: ste_dma40: Also report the number of logical channels Lee Jones
2013-05-03 20:53 ` Linus Walleij
2013-05-20 12:29 ` Linus Walleij
2013-05-23 10:48 ` Vinod Koul
2013-05-03 14:32 ` [PATCH 24/63] dmaengine: ste_dma40: Allocate plat_data on declaration Lee Jones
2013-05-03 20:55 ` Linus Walleij
2013-05-03 14:32 ` [PATCH 25/63] dmaengine: ste_dma40: Allow driver to be probe()able when DT is enabled Lee Jones
2013-05-03 20:58 ` Linus Walleij
2013-05-03 14:32 ` [PATCH 26/63] dmaengine: ste_dma40: Supply full Device Tree parsing support Lee Jones
2013-05-03 20:59 ` Linus Walleij
2013-05-03 21:00 ` Linus Walleij
2013-05-23 10:54 ` Vinod Koul
2013-05-03 14:32 ` [PATCH 27/63] ARM: ux500: Pass remnant platform data though to DMA40 driver Lee Jones
2013-05-03 21:09 ` Linus Walleij
2013-05-03 14:32 ` [PATCH 28/63] ARM: ux500: Stop passing UART's platform data for Device Tree boots Lee Jones
2013-05-03 21:11 ` Linus Walleij
2013-05-08 15:28 ` Lee Jones
2013-05-09 13:01 ` Lee Jones
2013-05-03 14:32 ` [PATCH 29/63] ARM: ux500: Stop passing MMC's " Lee Jones
2013-05-03 21:12 ` Linus Walleij
2013-05-03 14:32 ` [PATCH 30/63] ARM: ux500: Move SDI (MMC) and UART devices under more descriptive heading Lee Jones
2013-05-03 21:12 ` Linus Walleij
2013-05-03 14:32 ` [PATCH 31/63] dmaengine: ste_dma40: Only use addresses passed as configuration information Lee Jones
2013-05-03 21:16 ` Linus Walleij
2013-05-03 14:32 ` [PATCH 32/63] dmaengine: ste_dma40: Remove redundant address fetching function Lee Jones
2013-05-03 14:32 ` [PATCH 33/63] ARM: ux500: Remove DMA address look-up table Lee Jones
2013-05-03 14:32 ` [PATCH 34/63] dmaengine: ste_dma40: Correct copy/paste error Lee Jones
2013-05-03 14:32 ` [PATCH 35/63] ARM: ux500: Remove unnecessary attributes from DMA channel request pdata Lee Jones
2013-05-03 14:32 ` [PATCH 36/63] crypto: ux500/hash - Prepare clock before enabling it Lee Jones
2013-05-08 13:59 ` Ulf Hansson
2013-05-03 14:32 ` [PATCH 37/63] crypto: ux500/hash - Set DMA configuration though dma_slave_config() Lee Jones
2013-05-03 14:32 ` [PATCH 38/63] ARM: ux500: Stop passing Hash DMA channel config information though pdata Lee Jones
2013-05-03 14:32 ` [PATCH 39/63] crypto: ux500/cryp - Prepare clock before enabling it Lee Jones
2013-05-08 13:59 ` Ulf Hansson
2013-05-03 14:32 ` [PATCH 40/63] crypto: ux500/cryp - Set DMA configuration though dma_slave_config() Lee Jones
2013-05-03 14:32 ` [PATCH 41/63] ARM: ux500: Stop passing Cryp DMA channel config information though pdata Lee Jones
2013-05-03 14:32 ` [PATCH 42/63] crypto: ux500/[cryp|hash] - Show successful start-up in the bootlog Lee Jones
2013-05-03 14:32 ` [PATCH 43/63] ARM: ux500: Register Cyrp and Hash platform drivers on Snowball Lee Jones
2013-05-03 14:32 ` [PATCH 44/63] usb: musb: ux500: move channel number knowledge into the driver Lee Jones
2013-05-03 14:32 ` [PATCH 45/63] usb: musb: ux500: move the MUSB HDRC configuration " Lee Jones
2013-05-03 14:32 ` [PATCH 46/63] usb: musb: ux500: take the dma_mask from coherent_dma_mask Lee Jones
2013-05-03 14:32 ` [PATCH 47/63] usb: musb: ux500: harden checks for platform data Lee Jones
2013-05-03 14:32 ` [PATCH 48/63] usb: musb: ux500: attempt to find channels by name before using pdata Lee Jones
2013-05-03 14:32 ` [PATCH 49/63] usb: musb: ux500: add device tree probing support Lee Jones
2013-05-03 14:32 ` [PATCH 50/63] ARM: ux500: Add an auxdata entry for MUSB for clock-name look-up Lee Jones
2013-05-03 14:32 ` [PATCH 51/63] ARM: ux500: Remove ux500-musb platform registation when booting with DT Lee Jones
2013-05-03 14:32 ` [PATCH 52/63] ARM: ux500: Remove empty function u8500_of_init_devices() Lee Jones
2013-05-03 14:32 ` [PATCH 53/63] dmaengine: ste_dma40: Use the BIT macro to replace ugly '(1 << x)'s Lee Jones
2013-05-03 14:32 ` [PATCH 54/63] ARM: ux500: Replace ST-E's home-brew DMA direction definition with the generic one Lee Jones
2013-05-06 7:13 ` Srinidhi Kasagar
2013-05-07 7:39 ` Lee Jones
2013-05-07 9:42 ` Srinidhi Kasagar
2013-05-07 9:53 ` Lee Jones
2013-05-03 14:32 ` Lee Jones [this message]
2013-05-03 14:32 ` [PATCH 56/63] ARM: ux500: Remove recently unused stedma40_xfer_dir enums Lee Jones
2013-05-06 7:17 ` Srinidhi Kasagar
2013-05-03 14:32 ` [PATCH 57/63] dmaengine: ste_dma40_ll: Use the BIT macro to replace ugly '(1 << x)'s Lee Jones
2013-05-03 14:32 ` [PATCH 58/63] dmaengine: ste_dma40: Convert data_width from register bit format to value Lee Jones
2013-05-03 14:32 ` [PATCH 59/63] dmaengine: ste_dma40_ll: Replace meaningless register set with comment Lee Jones
2013-05-03 14:32 ` [PATCH 60/63] dmaengine: ste_dma40: Allow memcpy channels to be configured from DT Lee Jones
2013-05-03 14:32 ` [PATCH 61/63] ARM: ux500: Stop passing DMA platform data though AUXDATA Lee Jones
2013-05-06 6:55 ` Srinidhi Kasagar
2013-05-03 14:32 ` [PATCH 62/63] dmaengine: ste_dma40: Fetch the number of physical channels from DT Lee Jones
2013-05-03 14:32 ` [PATCH 63/63] dmaengine: ste_dma40: Fetch disabled " Lee Jones
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1367591569-32197-56-git-send-email-lee.jones@linaro.org \
--to=lee.jones@linaro.org \
--cc=arnd@arndb.de \
--cc=djbw@fb.com \
--cc=linus.walleij@stericsson.com \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-kernel@vger.kernel.org \
--cc=per.forlin@stericsson.com \
--cc=rabin@rab.in \
--cc=srinidhi.kasagar@stericsson.com \
--cc=vinod.koul@intel.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).