From: Luciano Coelho <coelho@ti.com>
To: <linux-wireless@vger.kernel.org>, <tony@atomide.com>, <nsekhar@ti.com>
Cc: <mturquette@linaro.org>, <mark.rutland@arm.com>, <balbi@ti.com>,
<grant.likely@linaro.org>, <rob.herring@calxeda.com>,
<devicetree-discuss@lists.ozlabs.org>,
<linux-doc@vger.kernel.org>, <linux-kernel@vger.kernel.org>,
<linux-omap@vger.kernel.org>,
<linux-arm-kernel@lists.infradead.org>, <coelho@ti.com>,
<nm@ti.com>
Subject: [PATCH v3 4/8] wl12xx: use frequency instead of enumerations for pdata clocks
Date: Wed, 3 Jul 2013 17:03:25 +0300 [thread overview]
Message-ID: <1372860209-3504-5-git-send-email-coelho@ti.com> (raw)
In-Reply-To: <1372860209-3504-1-git-send-email-coelho@ti.com>
Instead of defining an enumeration with the FW specific values for the
different clock rates, use the actual frequency instead. Also add a
boolean to specify whether the clock is XTAL or not.
Change all board files to reflect this.
Cc: Tony Lindgren <tony@atomide.com>
Cc: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
---
arch/arm/mach-davinci/board-da850-evm.c | 3 +-
arch/arm/mach-omap2/board-4430sdp.c | 5 ++-
arch/arm/mach-omap2/board-omap3evm.c | 3 +-
arch/arm/mach-omap2/board-omap4panda.c | 3 +-
arch/arm/mach-omap2/board-zoom-peripherals.c | 3 +-
drivers/net/wireless/ti/wl12xx/main.c | 57 +++++++++++++++++++++++++-
drivers/net/wireless/ti/wl12xx/wl12xx.h | 28 +++++++++++++
include/linux/wl12xx.h | 27 ++----------
8 files changed, 97 insertions(+), 32 deletions(-)
diff --git a/arch/arm/mach-davinci/board-da850-evm.c b/arch/arm/mach-davinci/board-da850-evm.c
index 544b6fa..eddced8 100644
--- a/arch/arm/mach-davinci/board-da850-evm.c
+++ b/arch/arm/mach-davinci/board-da850-evm.c
@@ -1377,7 +1377,8 @@ static const short da850_wl12xx_pins[] __initconst = {
static struct wl12xx_platform_data da850_wl12xx_wlan_data __initdata = {
.irq = -1,
- .board_ref_clock = WL12XX_REFCLOCK_38,
+ .ref_clock_freq = 38400000,
+ .ref_clock_xtal = false,
};
static __init int da850_wl12xx_init(void)
diff --git a/arch/arm/mach-omap2/board-4430sdp.c b/arch/arm/mach-omap2/board-4430sdp.c
index 953f620..0d3cb10 100644
--- a/arch/arm/mach-omap2/board-4430sdp.c
+++ b/arch/arm/mach-omap2/board-4430sdp.c
@@ -693,8 +693,9 @@ static void __init omap4_sdp4430_wifi_mux_init(void)
}
static struct wl12xx_platform_data omap4_sdp4430_wlan_data __initdata = {
- .board_ref_clock = WL12XX_REFCLOCK_26,
- .board_tcxo_clock = WL12XX_TCXOCLOCK_26,
+ .ref_clock_freq = 26000000,
+ .ref_clock_xtal = false,
+ .tcxo_clock_freq = 26000000,
};
static void __init omap4_sdp4430_wifi_init(void)
diff --git a/arch/arm/mach-omap2/board-omap3evm.c b/arch/arm/mach-omap2/board-omap3evm.c
index 8abce3cd..8f953ed 100644
--- a/arch/arm/mach-omap2/board-omap3evm.c
+++ b/arch/arm/mach-omap2/board-omap3evm.c
@@ -458,7 +458,8 @@ static struct platform_device omap3evm_wlan_regulator = {
};
struct wl12xx_platform_data omap3evm_wlan_data __initdata = {
- .board_ref_clock = WL12XX_REFCLOCK_38, /* 38.4 MHz */
+ .ref_clock_freq = 38400000,
+ .ref_clock_xtal = false,
};
#endif
diff --git a/arch/arm/mach-omap2/board-omap4panda.c b/arch/arm/mach-omap2/board-omap4panda.c
index 5b33626..b90fd4c 100644
--- a/arch/arm/mach-omap2/board-omap4panda.c
+++ b/arch/arm/mach-omap2/board-omap4panda.c
@@ -230,7 +230,8 @@ static struct platform_device omap_vwlan_device = {
};
static struct wl12xx_platform_data omap_panda_wlan_data __initdata = {
- .board_ref_clock = WL12XX_REFCLOCK_38, /* 38.4 MHz */
+ .ref_clock_freq = 38400000,
+ .ref_clock_xtal = false,
};
static struct twl6040_codec_data twl6040_codec = {
diff --git a/arch/arm/mach-omap2/board-zoom-peripherals.c b/arch/arm/mach-omap2/board-zoom-peripherals.c
index 4f84cf9..83a9a36 100644
--- a/arch/arm/mach-omap2/board-zoom-peripherals.c
+++ b/arch/arm/mach-omap2/board-zoom-peripherals.c
@@ -244,7 +244,8 @@ static struct platform_device *zoom_devices[] __initdata = {
};
static struct wl12xx_platform_data omap_zoom_wlan_data __initdata = {
- .board_ref_clock = WL12XX_REFCLOCK_26, /* 26 MHz */
+ .ref_clock_freq = 26000000,
+ .ref_clock_xtal = false,
};
static struct omap2_hsmmc_info mmc[] = {
diff --git a/drivers/net/wireless/ti/wl12xx/main.c b/drivers/net/wireless/ti/wl12xx/main.c
index 1c627da..216c2fd 100644
--- a/drivers/net/wireless/ti/wl12xx/main.c
+++ b/drivers/net/wireless/ti/wl12xx/main.c
@@ -1701,6 +1701,42 @@ static struct ieee80211_sta_ht_cap wl12xx_ht_cap = {
},
};
+static const struct wl12xx_clock wl12xx_refclock_table[] = {
+ { 19200000, false, WL12XX_REFCLOCK_19 },
+ { 26000000, false, WL12XX_REFCLOCK_26 },
+ { 26000000, true, WL12XX_REFCLOCK_26_XTAL },
+ { 38400000, false, WL12XX_REFCLOCK_38 },
+ { 38400000, true, WL12XX_REFCLOCK_38_XTAL },
+ { 52000000, false, WL12XX_REFCLOCK_52 },
+ { 0, false, 0 }
+};
+
+static const struct wl12xx_clock wl12xx_tcxoclock_table[] = {
+ { 16368000, true, WL12XX_TCXOCLOCK_16_368 },
+ { 16800000, true, WL12XX_TCXOCLOCK_16_8 },
+ { 19200000, true, WL12XX_TCXOCLOCK_19_2 },
+ { 26000000, true, WL12XX_TCXOCLOCK_26 },
+ { 32736000, true, WL12XX_TCXOCLOCK_32_736 },
+ { 33600000, true, WL12XX_TCXOCLOCK_33_6 },
+ { 38400000, true, WL12XX_TCXOCLOCK_38_4 },
+ { 52000000, true, WL12XX_TCXOCLOCK_52 },
+ { 0, false, 0 }
+};
+
+static int wl12xx_get_clock_idx(struct wl12xx_clock *table, u32 freq, bool xtal)
+{
+ int i = 0;
+
+ while(table[i].freq != 0) {
+ if ((table[i].freq == freq) &&
+ (table[i].xtal == xtal))
+ return table[i].hw_idx;
+ i++;
+ };
+
+ return -EINVAL;
+}
+
static int wl12xx_setup(struct wl1271 *wl)
{
struct wl12xx_priv *priv = wl->priv;
@@ -1722,7 +1758,16 @@ static int wl12xx_setup(struct wl1271 *wl)
wl12xx_conf_init(wl);
if (!fref_param) {
- priv->ref_clock = pdata->board_ref_clock;
+ priv->ref_clock = wl12xx_get_clock_idx(wl12xx_refclock_table,
+ pdata->ref_clock_freq,
+ pdata->ref_clock_xtal);
+ if (priv->ref_clock < 0) {
+ wl1271_error("Invalid ref_clock frequency (%d Hz, %s)",
+ pdata->ref_clock_freq,
+ pdata->ref_clock_xtal ? "XTAL" : "not XTAL");
+
+ return priv->ref_clock;
+ }
} else {
if (!strcmp(fref_param, "19.2"))
priv->ref_clock = WL12XX_REFCLOCK_19;
@@ -1741,7 +1786,15 @@ static int wl12xx_setup(struct wl1271 *wl)
}
if (!tcxo_param) {
- priv->tcxo_clock = pdata->board_tcxo_clock;
+ priv->tcxo_clock = wl12xx_get_clock_idx(wl12xx_tcxoclock_table,
+ pdata->tcxo_clock_freq,
+ true);
+ if (priv->tcxo_clock < 0) {
+ wl1271_error("Invalid tcxo_clock frequency (%d Hz)",
+ pdata->tcxo_clock_freq);
+
+ return priv->tcxo_clock;
+ }
} else {
if (!strcmp(tcxo_param, "19.2"))
priv->tcxo_clock = WL12XX_TCXOCLOCK_19_2;
diff --git a/drivers/net/wireless/ti/wl12xx/wl12xx.h b/drivers/net/wireless/ti/wl12xx/wl12xx.h
index 9e5484a..05f631b 100644
--- a/drivers/net/wireless/ti/wl12xx/wl12xx.h
+++ b/drivers/net/wireless/ti/wl12xx/wl12xx.h
@@ -79,4 +79,32 @@ struct wl12xx_priv {
struct wl127x_rx_mem_pool_addr *rx_mem_addr;
};
+/* Reference clock values */
+enum {
+ WL12XX_REFCLOCK_19 = 0, /* 19.2 MHz */
+ WL12XX_REFCLOCK_26 = 1, /* 26 MHz */
+ WL12XX_REFCLOCK_38 = 2, /* 38.4 MHz */
+ WL12XX_REFCLOCK_52 = 3, /* 52 MHz */
+ WL12XX_REFCLOCK_38_XTAL = 4, /* 38.4 MHz, XTAL */
+ WL12XX_REFCLOCK_26_XTAL = 5, /* 26 MHz, XTAL */
+};
+
+/* TCXO clock values */
+enum {
+ WL12XX_TCXOCLOCK_19_2 = 0, /* 19.2MHz */
+ WL12XX_TCXOCLOCK_26 = 1, /* 26 MHz */
+ WL12XX_TCXOCLOCK_38_4 = 2, /* 38.4MHz */
+ WL12XX_TCXOCLOCK_52 = 3, /* 52 MHz */
+ WL12XX_TCXOCLOCK_16_368 = 4, /* 16.368 MHz */
+ WL12XX_TCXOCLOCK_32_736 = 5, /* 32.736 MHz */
+ WL12XX_TCXOCLOCK_16_8 = 6, /* 16.8 MHz */
+ WL12XX_TCXOCLOCK_33_6 = 7, /* 33.6 MHz */
+};
+
+struct wl12xx_clock {
+ u32 freq;
+ bool xtal;
+ u8 hw_idx;
+};
+
#endif /* __WL12XX_PRIV_H__ */
diff --git a/include/linux/wl12xx.h b/include/linux/wl12xx.h
index ab90b1c..11491ad 100644
--- a/include/linux/wl12xx.h
+++ b/include/linux/wl12xx.h
@@ -26,28 +26,6 @@
#include <linux/err.h>
-/* Reference clock values */
-enum {
- WL12XX_REFCLOCK_19 = 0, /* 19.2 MHz */
- WL12XX_REFCLOCK_26 = 1, /* 26 MHz */
- WL12XX_REFCLOCK_38 = 2, /* 38.4 MHz */
- WL12XX_REFCLOCK_52 = 3, /* 52 MHz */
- WL12XX_REFCLOCK_38_XTAL = 4, /* 38.4 MHz, XTAL */
- WL12XX_REFCLOCK_26_XTAL = 5, /* 26 MHz, XTAL */
-};
-
-/* TCXO clock values */
-enum {
- WL12XX_TCXOCLOCK_19_2 = 0, /* 19.2MHz */
- WL12XX_TCXOCLOCK_26 = 1, /* 26 MHz */
- WL12XX_TCXOCLOCK_38_4 = 2, /* 38.4MHz */
- WL12XX_TCXOCLOCK_52 = 3, /* 52 MHz */
- WL12XX_TCXOCLOCK_16_368 = 4, /* 16.368 MHz */
- WL12XX_TCXOCLOCK_32_736 = 5, /* 32.736 MHz */
- WL12XX_TCXOCLOCK_16_8 = 6, /* 16.8 MHz */
- WL12XX_TCXOCLOCK_33_6 = 7, /* 33.6 MHz */
-};
-
struct wl1251_platform_data {
void (*set_power)(bool enable);
/* SDIO only: IRQ number if WLAN_IRQ line is used, 0 for SDIO IRQs */
@@ -57,8 +35,9 @@ struct wl1251_platform_data {
struct wl12xx_platform_data {
int irq;
- int board_ref_clock;
- int board_tcxo_clock;
+ int ref_clock_freq; /* in Hertz */
+ bool ref_clock_xtal; /* specify whether the clock is XTAL or not */
+ int tcxo_clock_freq; /* in Hertz, tcxo is always XTAL */
};
#ifdef CONFIG_WILINK_PLATFORM_DATA
--
1.7.10.4
next prev parent reply other threads:[~2013-07-03 14:04 UTC|newest]
Thread overview: 21+ messages / expand[flat|nested] mbox.gz Atom feed top
2013-07-03 14:03 [PATCH v3 0/8] wilink: add device tree support Luciano Coelho
2013-07-03 14:03 ` [PATCH v3 1/8] wl1251: split wl251 platform data to a separate structure Luciano Coelho
2013-07-03 14:11 ` Felipe Balbi
2013-07-03 14:03 ` [PATCH v3 2/8] wlcore: set irq_flags in the board files instead of hiding behind a quirk Luciano Coelho
2013-07-03 14:13 ` Felipe Balbi
2013-07-03 14:18 ` Luciano Coelho
2013-07-03 14:23 ` Felipe Balbi
2013-07-03 14:15 ` Luciano Coelho
2013-07-03 15:12 ` Javier Martinez Canillas
2013-07-04 14:21 ` Luciano Coelho
2013-07-04 4:46 ` Sekhar Nori
2013-07-03 14:03 ` [PATCH v3 3/8] wlcore: remove pwr_in_suspend from platform data Luciano Coelho
2013-07-03 14:14 ` Felipe Balbi
2013-07-03 14:03 ` Luciano Coelho [this message]
2013-07-03 14:16 ` [PATCH v3 4/8] wl12xx: use frequency instead of enumerations for pdata clocks Felipe Balbi
2013-07-03 14:03 ` [PATCH v3 5/8] wlcore: add initial device tree support to the sdio module Luciano Coelho
2013-07-03 14:18 ` Felipe Balbi
2013-07-03 14:03 ` [PATCH v3 6/8] wlcore: sdio: add wilink clock providers Luciano Coelho
2013-07-03 14:03 ` [PATCH v3 7/8] wlcore: sdio: get clocks from device tree Luciano Coelho
2013-07-03 14:03 ` [PATCH v3 8/8] wlcore/wl12xx: check if we got correct clock data from DT Luciano Coelho
2013-07-03 14:19 ` Felipe Balbi
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1372860209-3504-5-git-send-email-coelho@ti.com \
--to=coelho@ti.com \
--cc=balbi@ti.com \
--cc=devicetree-discuss@lists.ozlabs.org \
--cc=grant.likely@linaro.org \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-doc@vger.kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-omap@vger.kernel.org \
--cc=linux-wireless@vger.kernel.org \
--cc=mark.rutland@arm.com \
--cc=mturquette@linaro.org \
--cc=nm@ti.com \
--cc=nsekhar@ti.com \
--cc=rob.herring@calxeda.com \
--cc=tony@atomide.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox