* [PATCH RFT] regulator: pfuze100: Fix n_voltages setting for SW2~SW4 with high bit set
@ 2013-07-30 2:46 Axel Lin
2013-07-30 3:23 ` Robin Gong
2013-07-30 10:21 ` Mark Brown
0 siblings, 2 replies; 5+ messages in thread
From: Axel Lin @ 2013-07-30 2:46 UTC (permalink / raw)
To: Mark Brown; +Cc: Robin Gong, Liam Girdwood, linux-kernel
Current code adjust min_uV and uV_step but missed adjusting the n_voltages
setting.
When BIT6 is clear:
n_voltages = (1975000 - 400000) / 25000 + 1 = 64
When BIT6 is set:
n_voltages = (3300000 - 800000) / 50000 + 1 = 51
The n_voltages needs update because when BIT6 is set 0x73 ~ 0x7f are reserved.
When using regulator_list_voltage_linear, the n_voltages does matter here
because wrong n_voltages setting make the equation return wrong result.
e.g. if selector is 63, regulator_list_voltage_linear returns
800000 + (50000 * 63) = 4000000
It should return -EINVAL if the selector is in the range of 51 ~ 63.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
---
drivers/regulator/pfuze100-regulator.c | 16 ++++++++--------
1 file changed, 8 insertions(+), 8 deletions(-)
diff --git a/drivers/regulator/pfuze100-regulator.c b/drivers/regulator/pfuze100-regulator.c
index 2dadc31..a77379b 100644
--- a/drivers/regulator/pfuze100-regulator.c
+++ b/drivers/regulator/pfuze100-regulator.c
@@ -387,8 +387,11 @@ static int pfuze100_regulator_probe(struct i2c_client *client,
for (i = 0; i < PFUZE100_MAX_REGULATOR; i++) {
struct regulator_init_data *init_data;
+ struct regulator_desc *desc;
int val;
+ desc = &pfuze_chip->regulator_descs[i].desc;
+
if (pdata)
init_data = pdata->init_data[i];
else
@@ -396,13 +399,11 @@ static int pfuze100_regulator_probe(struct i2c_client *client,
/* SW2~SW4 high bit check and modify the voltage value table */
if (i > PFUZE100_SW1C && i < PFUZE100_SWBST) {
- regmap_read(pfuze_chip->regmap, PFUZE100_SW2VOL +
- (i - PFUZE100_SW2) * 7, &val);
+ regmap_read(pfuze_chip->regmap, desc->vsel_reg, &val);
if (val & 0x40) {
- pfuze_chip->regulator_descs[i].desc.min_uV
- = 800000;
- pfuze_chip->regulator_descs[i].desc.uV_step
- = 50000;
+ desc->min_uV = 800000;
+ desc->uV_step = 50000;
+ desc->n_voltages = 51;
}
}
@@ -411,8 +412,7 @@ static int pfuze100_regulator_probe(struct i2c_client *client,
config.driver_data = pfuze_chip;
config.of_node = match_of_node(i);
- pfuze_chip->regulators[i] = regulator_register(&pfuze_chip
- ->regulator_descs[i].desc, &config);
+ pfuze_chip->regulators[i] = regulator_register(desc, &config);
if (IS_ERR(pfuze_chip->regulators[i])) {
dev_err(&client->dev, "register regulator%s failed\n",
pfuze100_regulators[i].desc.name);
--
1.8.1.2
^ permalink raw reply related [flat|nested] 5+ messages in thread
* Re: [PATCH RFT] regulator: pfuze100: Fix n_voltages setting for SW2~SW4 with high bit set
2013-07-30 2:46 [PATCH RFT] regulator: pfuze100: Fix n_voltages setting for SW2~SW4 with high bit set Axel Lin
@ 2013-07-30 3:23 ` Robin Gong
2013-07-30 10:21 ` Mark Brown
2013-07-30 10:21 ` Mark Brown
1 sibling, 1 reply; 5+ messages in thread
From: Robin Gong @ 2013-07-30 3:23 UTC (permalink / raw)
To: Axel Lin; +Cc: Mark Brown, Liam Girdwood, linux-kernel
Ok for me.
On Tue, Jul 30, 2013 at 10:46:28AM +0800, Axel Lin wrote:
> Current code adjust min_uV and uV_step but missed adjusting the n_voltages
> setting.
>
> When BIT6 is clear:
> n_voltages = (1975000 - 400000) / 25000 + 1 = 64
> When BIT6 is set:
> n_voltages = (3300000 - 800000) / 50000 + 1 = 51
>
> The n_voltages needs update because when BIT6 is set 0x73 ~ 0x7f are reserved.
> When using regulator_list_voltage_linear, the n_voltages does matter here
> because wrong n_voltages setting make the equation return wrong result.
> e.g. if selector is 63, regulator_list_voltage_linear returns
> 800000 + (50000 * 63) = 4000000
> It should return -EINVAL if the selector is in the range of 51 ~ 63.
>
> Signed-off-by: Axel Lin <axel.lin@ingics.com>
> ---
> drivers/regulator/pfuze100-regulator.c | 16 ++++++++--------
> 1 file changed, 8 insertions(+), 8 deletions(-)
>
> diff --git a/drivers/regulator/pfuze100-regulator.c b/drivers/regulator/pfuze100-regulator.c
> index 2dadc31..a77379b 100644
> --- a/drivers/regulator/pfuze100-regulator.c
> +++ b/drivers/regulator/pfuze100-regulator.c
> @@ -387,8 +387,11 @@ static int pfuze100_regulator_probe(struct i2c_client *client,
>
> for (i = 0; i < PFUZE100_MAX_REGULATOR; i++) {
> struct regulator_init_data *init_data;
> + struct regulator_desc *desc;
> int val;
>
> + desc = &pfuze_chip->regulator_descs[i].desc;
> +
> if (pdata)
> init_data = pdata->init_data[i];
> else
> @@ -396,13 +399,11 @@ static int pfuze100_regulator_probe(struct i2c_client *client,
>
> /* SW2~SW4 high bit check and modify the voltage value table */
> if (i > PFUZE100_SW1C && i < PFUZE100_SWBST) {
> - regmap_read(pfuze_chip->regmap, PFUZE100_SW2VOL +
> - (i - PFUZE100_SW2) * 7, &val);
> + regmap_read(pfuze_chip->regmap, desc->vsel_reg, &val);
> if (val & 0x40) {
> - pfuze_chip->regulator_descs[i].desc.min_uV
> - = 800000;
> - pfuze_chip->regulator_descs[i].desc.uV_step
> - = 50000;
> + desc->min_uV = 800000;
> + desc->uV_step = 50000;
> + desc->n_voltages = 51;
> }
> }
>
> @@ -411,8 +412,7 @@ static int pfuze100_regulator_probe(struct i2c_client *client,
> config.driver_data = pfuze_chip;
> config.of_node = match_of_node(i);
>
> - pfuze_chip->regulators[i] = regulator_register(&pfuze_chip
> - ->regulator_descs[i].desc, &config);
> + pfuze_chip->regulators[i] = regulator_register(desc, &config);
> if (IS_ERR(pfuze_chip->regulators[i])) {
> dev_err(&client->dev, "register regulator%s failed\n",
> pfuze100_regulators[i].desc.name);
> --
> 1.8.1.2
>
>
>
>
^ permalink raw reply [flat|nested] 5+ messages in thread
* Re: [PATCH RFT] regulator: pfuze100: Fix n_voltages setting for SW2~SW4 with high bit set
2013-07-30 3:23 ` Robin Gong
@ 2013-07-30 10:21 ` Mark Brown
2013-07-30 10:54 ` Robin Gong
0 siblings, 1 reply; 5+ messages in thread
From: Mark Brown @ 2013-07-30 10:21 UTC (permalink / raw)
To: Robin Gong; +Cc: Axel Lin, Liam Girdwood, linux-kernel
[-- Attachment #1: Type: text/plain, Size: 341 bytes --]
On Tue, Jul 30, 2013 at 11:23:11AM +0800, Robin Gong wrote:
> Ok for me.
For Linux kernel process you should say
Acked-by: Robin Gong <b38343@freescale.com>
or
Reviewed-by: Robin Gong <b38343@freescale.com>
to say if you are OK - the first means you didn't really review but it
looks OK, the second means you did a proper review.
[-- Attachment #2: Digital signature --]
[-- Type: application/pgp-signature, Size: 836 bytes --]
^ permalink raw reply [flat|nested] 5+ messages in thread
* Re: [PATCH RFT] regulator: pfuze100: Fix n_voltages setting for SW2~SW4 with high bit set
2013-07-30 2:46 [PATCH RFT] regulator: pfuze100: Fix n_voltages setting for SW2~SW4 with high bit set Axel Lin
2013-07-30 3:23 ` Robin Gong
@ 2013-07-30 10:21 ` Mark Brown
1 sibling, 0 replies; 5+ messages in thread
From: Mark Brown @ 2013-07-30 10:21 UTC (permalink / raw)
To: Axel Lin; +Cc: Robin Gong, Liam Girdwood, linux-kernel
[-- Attachment #1: Type: text/plain, Size: 164 bytes --]
On Tue, Jul 30, 2013 at 10:46:28AM +0800, Axel Lin wrote:
> Current code adjust min_uV and uV_step but missed adjusting the n_voltages
> setting.
Applied, thanks.
[-- Attachment #2: Digital signature --]
[-- Type: application/pgp-signature, Size: 836 bytes --]
^ permalink raw reply [flat|nested] 5+ messages in thread
* Re: [PATCH RFT] regulator: pfuze100: Fix n_voltages setting for SW2~SW4 with high bit set
2013-07-30 10:21 ` Mark Brown
@ 2013-07-30 10:54 ` Robin Gong
0 siblings, 0 replies; 5+ messages in thread
From: Robin Gong @ 2013-07-30 10:54 UTC (permalink / raw)
To: Mark Brown; +Cc: Axel Lin, Liam Girdwood, linux-kernel
Hi Mark,
Thanks for your kindly remind.
On Tue, Jul 30, 2013 at 11:21:10AM +0100, Mark Brown wrote:
> On Tue, Jul 30, 2013 at 11:23:11AM +0800, Robin Gong wrote:
> > Ok for me.
>
> For Linux kernel process you should say
>
> Acked-by: Robin Gong <b38343@freescale.com>
>
> or
>
> Reviewed-by: Robin Gong <b38343@freescale.com>
>
> to say if you are OK - the first means you didn't really review but it
> looks OK, the second means you did a proper review.
^ permalink raw reply [flat|nested] 5+ messages in thread
end of thread, other threads:[~2013-07-30 10:50 UTC | newest]
Thread overview: 5+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
2013-07-30 2:46 [PATCH RFT] regulator: pfuze100: Fix n_voltages setting for SW2~SW4 with high bit set Axel Lin
2013-07-30 3:23 ` Robin Gong
2013-07-30 10:21 ` Mark Brown
2013-07-30 10:54 ` Robin Gong
2013-07-30 10:21 ` Mark Brown
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox