[PATCH 1/4] ARM: at91: remove at91sam9263 legacy board support

Nicolas Ferre
2014-11-19T10:31:45Z

Remove legacy support for at91sam9rl boards.
This include board files removal plus all legacy code for non DT boards
support.
Use the Device Tree for running this board with newer kernels.

Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
---
arch/arm/configs/at91sam9263_defconfig | 151 ---
arch/arm/mach-at91/Kconfig.non_dt | 21 -
arch/arm/mach-at91/Makefile | 4 -
arch/arm/mach-at91/at91sam9263.c | 399 --------
arch/arm/mach-at91/at91sam9263_devices.c | 1538 ------------------------------
arch/arm/mach-at91/board-sam9263ek.c | 493 ----------
6 files changed, 2606 deletions(-)
delete mode 100644 arch/arm/configs/at91sam9263_defconfig
delete mode 100644 arch/arm/mach-at91/at91sam9263_devices.c
delete mode 100644 arch/arm/mach-at91/board-sam9263ek.c

diff --git a/arch/arm/configs/at91sam9263_defconfig b/arch/arm/configs/at91sam9263_defconfig
deleted file mode 100644
index 8b671c977b81..000000000000
--- a/arch/arm/configs/at91sam9263_defconfig
+++ /dev/null
@@ -1,151 +0,0 @@
-# CONFIG_LOCALVERSION_AUTO is not set
-# CONFIG_SWAP is not set
-CONFIG_SYSVIPC=y
-CONFIG_IKCONFIG=y
-CONFIG_IKCONFIG_PROC=y
-CONFIG_LOG_BUF_SHIFT=14
-CONFIG_NAMESPACES=y
-CONFIG_EMBEDDED=y
-CONFIG_SLAB=y
-CONFIG_MODULES=y
-CONFIG_MODULE_UNLOAD=y
-# CONFIG_BLK_DEV_BSG is not set
-# CONFIG_IOSCHED_DEADLINE is not set
-# CONFIG_IOSCHED_CFQ is not set
-CONFIG_ARCH_AT91=y
-CONFIG_ARCH_AT91SAM9263=y
-CONFIG_MACH_AT91SAM9263EK=y
-CONFIG_MTD_AT91_DATAFLASH_CARD=y
-# CONFIG_ARM_THUMB is not set
-CONFIG_AEABI=y
-CONFIG_ZBOOT_ROM_TEXT=0x0
-CONFIG_ZBOOT_ROM_BSS=0x0
-CONFIG_CMDLINE="mem=64M console=ttyS0,115200 initrd=0x21100000,3145728 root=/dev/ram0 rw"
-CONFIG_AUTO_ZRELADDR=y
-CONFIG_NET=y
-CONFIG_PACKET=y
-CONFIG_UNIX=y
-CONFIG_NET_KEY=y
-CONFIG_INET=y
-CONFIG_IP_MULTICAST=y
-CONFIG_IP_ADVANCED_ROUTER=y
-CONFIG_IP_ROUTE_VERBOSE=y
-CONFIG_IP_PNP=y
-CONFIG_IP_PNP_DHCP=y
-CONFIG_IP_PNP_BOOTP=y
-CONFIG_IP_PNP_RARP=y
-CONFIG_NET_IPIP=y
-CONFIG_IP_MROUTE=y
-CONFIG_IP_PIMSM_V1=y
-CONFIG_IP_PIMSM_V2=y
-# CONFIG_INET_XFRM_MODE_TRANSPORT is not set
-# CONFIG_INET_XFRM_MODE_TUNNEL is not set
-# CONFIG_INET_XFRM_MODE_BEET is not set
-# CONFIG_INET_LRO is not set
-# CONFIG_INET_DIAG is not set
-CONFIG_IPV6=y
-# CONFIG_WIRELESS is not set
-CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug"
-CONFIG_DEVTMPFS=y
-CONFIG_DEVTMPFS_MOUNT=y
-CONFIG_MTD=y
-CONFIG_MTD_CMDLINE_PARTS=y
-CONFIG_MTD_BLOCK=y
-CONFIG_NFTL=y
-CONFIG_NFTL_RW=y
-CONFIG_MTD_DATAFLASH=y
-CONFIG_MTD_BLOCK2MTD=y
-CONFIG_MTD_NAND=y
-CONFIG_MTD_NAND_ATMEL=y
-CONFIG_MTD_UBI=y
-CONFIG_MTD_UBI_GLUEBI=y
-CONFIG_BLK_DEV_LOOP=y
-CONFIG_BLK_DEV_RAM=y
-CONFIG_BLK_DEV_RAM_SIZE=8192
-CONFIG_ATMEL_TCLIB=y
-CONFIG_SCSI=y
-CONFIG_BLK_DEV_SD=y
-CONFIG_NETDEVICES=y
-CONFIG_MACB=y
-CONFIG_SMSC_PHY=y
-# CONFIG_WLAN is not set
-CONFIG_INPUT_POLLDEV=m
-# CONFIG_INPUT_MOUSEDEV is not set
-CONFIG_INPUT_EVDEV=y
-# CONFIG_KEYBOARD_ATKBD is not set
-CONFIG_KEYBOARD_GPIO=y
-# CONFIG_INPUT_MOUSE is not set
-CONFIG_INPUT_TOUCHSCREEN=y
-CONFIG_TOUCHSCREEN_ADS7846=y
-# CONFIG_LEGACY_PTYS is not set
-CONFIG_SERIAL_ATMEL=y
-CONFIG_SERIAL_ATMEL_CONSOLE=y
-CONFIG_HW_RANDOM=y
-CONFIG_I2C=y
-CONFIG_I2C_CHARDEV=y
-CONFIG_I2C_GPIO=y
-CONFIG_SPI=y
-CONFIG_SPI_ATMEL=y
-CONFIG_GPIO_SYSFS=y
-CONFIG_POWER_SUPPLY=y
-CONFIG_POWER_RESET=y
-# CONFIG_HWMON is not set
-CONFIG_WATCHDOG=y
-CONFIG_WATCHDOG_NOWAYOUT=y
-CONFIG_AT91SAM9X_WATCHDOG=y
-CONFIG_FB=y
-CONFIG_FB_ATMEL=y
-CONFIG_BACKLIGHT_LCD_SUPPORT=y
-CONFIG_LCD_CLASS_DEVICE=y
-CONFIG_BACKLIGHT_CLASS_DEVICE=y
-CONFIG_FRAMEBUFFER_CONSOLE=y
-CONFIG_FRAMEBUFFER_CONSOLE_DETECT_PRIMARY=y
-CONFIG_LOGO=y
-CONFIG_SOUND=y
-CONFIG_SND=y
-CONFIG_SND_SEQUENCER=y
-CONFIG_SND_MIXER_OSS=y
-CONFIG_SND_PCM_OSS=y
-# CONFIG_SND_SUPPORT_OLD_API is not set
-# CONFIG_SND_VERBOSE_PROCFS is not set
-# CONFIG_SND_DRIVERS is not set
-# CONFIG_SND_ARM is not set
-CONFIG_SND_ATMEL_AC97C=y
-# CONFIG_SND_SPI is not set
-CONFIG_SND_USB_AUDIO=m
-CONFIG_USB=y
-CONFIG_USB_MON=y
-CONFIG_USB_OHCI_HCD=y
-CONFIG_USB_STORAGE=y
-CONFIG_USB_GADGET=y
-CONFIG_USB_ATMEL_USBA=y
-CONFIG_USB_G_SERIAL=y
-CONFIG_MMC=y
-CONFIG_SDIO_UART=m
-CONFIG_MMC_ATMELMCI=m
-CONFIG_NEW_LEDS=y
-CONFIG_LEDS_CLASS=y
-CONFIG_LEDS_GPIO=y
-CONFIG_LEDS_PWM=y
-CONFIG_LEDS_TRIGGERS=y
-CONFIG_LEDS_TRIGGER_HEARTBEAT=y
-CONFIG_RTC_CLASS=y
-CONFIG_RTC_DRV_AT91SAM9=y
-CONFIG_PWM=y
-CONFIG_PWM_ATMEL=y
-CONFIG_EXT4_FS=y
-CONFIG_VFAT_FS=y
-CONFIG_TMPFS=y
-CONFIG_UBIFS_FS=y
-CONFIG_UBIFS_FS_ADVANCED_COMPR=y
-CONFIG_NFS_FS=y
-CONFIG_NFS_V3_ACL=y
-CONFIG_NFS_V4=y
-CONFIG_ROOT_NFS=y
-CONFIG_NLS_CODEPAGE_437=y
-CONFIG_NLS_CODEPAGE_850=y
-CONFIG_NLS_ISO8859_1=y
-CONFIG_NLS_UTF8=y
-CONFIG_DEBUG_USER=y
-CONFIG_XZ_DEC=y
-CONFIG_FONTS=y
diff --git a/arch/arm/mach-at91/Kconfig.non_dt b/arch/arm/mach-at91/Kconfig.non_dt
index 22963a829e5c..a9458234ab23 100644
--- a/arch/arm/mach-at91/Kconfig.non_dt
+++ b/arch/arm/mach-at91/Kconfig.non_dt
@@ -27,12 +27,6 @@ config ARCH_AT91SAM9261
select AT91_USE_OLD_CLK
select OLD_IRQ_AT91

-config ARCH_AT91SAM9263
- bool "AT91SAM9263"
- select SOC_AT91SAM9263
- select AT91_USE_OLD_CLK
- select OLD_IRQ_AT91
-
endchoice

config ARCH_AT91SAM9G20
@@ -260,21 +254,6 @@ endif

# ----------------------------------------------------------

-if ARCH_AT91SAM9263
-
-comment "AT91SAM9263 Board Type"
-
-config MACH_AT91SAM9263EK
- bool "Atmel AT91SAM9263-EK Evaluation Kit"
- select HAVE_AT91_DATAFLASH_CARD
- help
- Select this if you are using Atmel's AT91SAM9263-EK Evaluation Kit.
- <http://www.atmel.com/dyn/products/tools_card.asp?tool_id=4057>
-
-endif
-
-# ----------------------------------------------------------
-
comment "AT91 Board Options"

config MTD_AT91_DATAFLASH_CARD
diff --git a/arch/arm/mach-at91/Makefile b/arch/arm/mach-at91/Makefile
index ae8aa1a898e8..e0361357e018 100644
--- a/arch/arm/mach-at91/Makefile
+++ b/arch/arm/mach-at91/Makefile
@@ -23,7 +23,6 @@ obj-$(CONFIG_SOC_SAMA5D4) += sama5d4.o
obj-$(CONFIG_ARCH_AT91RM9200) += at91rm9200_devices.o
obj-$(CONFIG_ARCH_AT91SAM9260) += at91sam9260_devices.o
obj-$(CONFIG_ARCH_AT91SAM9261) += at91sam9261_devices.o
-obj-$(CONFIG_ARCH_AT91SAM9263) += at91sam9263_devices.o

# AT91RM9200 board-specific support
obj-$(CONFIG_MACH_ONEARM) += board-1arm.o
@@ -52,9 +51,6 @@ obj-$(CONFIG_MACH_FLEXIBITY) += board-flexibity.o
obj-$(CONFIG_MACH_AT91SAM9261EK) += board-sam9261ek.o
obj-$(CONFIG_MACH_AT91SAM9G10EK) += board-sam9261ek.o

-# AT91SAM9263 board-specific support
-obj-$(CONFIG_MACH_AT91SAM9263EK) += board-sam9263ek.o
-
# AT91SAM9G20 board-specific support
obj-$(CONFIG_MACH_AT91SAM9G20EK) += board-sam9g20ek.o
obj-$(CONFIG_MACH_CPU9G20) += board-cpu9krea.o
diff --git a/arch/arm/mach-at91/at91sam9263.c b/arch/arm/mach-at91/at91sam9263.c
index fbff228cc63e..e7ad14864083 100644
--- a/arch/arm/mach-at91/at91sam9263.c
+++ b/arch/arm/mach-at91/at91sam9263.c
@@ -10,304 +10,11 @@
*
*/

-#include <linux/module.h>
-#include <linux/platform_device.h>
-#include <linux/clk/at91_pmc.h>
-
-#include <asm/proc-fns.h>
-#include <asm/irq.h>
-#include <asm/mach/arch.h>
-#include <asm/mach/map.h>
#include <asm/system_misc.h>
-#include <mach/at91sam9263.h>
#include <mach/hardware.h>

-#include "at91_aic.h"
#include "soc.h"
#include "generic.h"
-#include "sam9_smc.h"
-#include "pm.h"
-
-#if defined(CONFIG_OLD_CLK_AT91)
-#include "clock.h"
-/* --------------------------------------------------------------------
- * Clocks
- * -------------------------------------------------------------------- */
-
-/*
- * The peripheral clocks.
- */
-static struct clk pioA_clk = {
- .name = "pioA_clk",
- .pmc_mask = 1 << AT91SAM9263_ID_PIOA,
- .type = CLK_TYPE_PERIPHERAL,
-};
-static struct clk pioB_clk = {
- .name = "pioB_clk",
- .pmc_mask = 1 << AT91SAM9263_ID_PIOB,
- .type = CLK_TYPE_PERIPHERAL,
-};
-static struct clk pioCDE_clk = {
- .name = "pioCDE_clk",
- .pmc_mask = 1 << AT91SAM9263_ID_PIOCDE,
- .type = CLK_TYPE_PERIPHERAL,
-};
-static struct clk usart0_clk = {
- .name = "usart0_clk",
- .pmc_mask = 1 << AT91SAM9263_ID_US0,
- .type = CLK_TYPE_PERIPHERAL,
-};
-static struct clk usart1_clk = {
- .name = "usart1_clk",
- .pmc_mask = 1 << AT91SAM9263_ID_US1,
- .type = CLK_TYPE_PERIPHERAL,
-};
-static struct clk usart2_clk = {
- .name = "usart2_clk",
- .pmc_mask = 1 << AT91SAM9263_ID_US2,
- .type = CLK_TYPE_PERIPHERAL,
-};
-static struct clk mmc0_clk = {
- .name = "mci0_clk",
- .pmc_mask = 1 << AT91SAM9263_ID_MCI0,
- .type = CLK_TYPE_PERIPHERAL,
-};
-static struct clk mmc1_clk = {
- .name = "mci1_clk",
- .pmc_mask = 1 << AT91SAM9263_ID_MCI1,
- .type = CLK_TYPE_PERIPHERAL,
-};
-static struct clk can_clk = {
- .name = "can_clk",
- .pmc_mask = 1 << AT91SAM9263_ID_CAN,
- .type = CLK_TYPE_PERIPHERAL,
-};
-static struct clk twi_clk = {
- .name = "twi_clk",
- .pmc_mask = 1 << AT91SAM9263_ID_TWI,
- .type = CLK_TYPE_PERIPHERAL,
-};
-static struct clk spi0_clk = {
- .name = "spi0_clk",
- .pmc_mask = 1 << AT91SAM9263_ID_SPI0,
- .type = CLK_TYPE_PERIPHERAL,
-};
-static struct clk spi1_clk = {
- .name = "spi1_clk",
- .pmc_mask = 1 << AT91SAM9263_ID_SPI1,
- .type = CLK_TYPE_PERIPHERAL,
-};
-static struct clk ssc0_clk = {
- .name = "ssc0_clk",
- .pmc_mask = 1 << AT91SAM9263_ID_SSC0,
- .type = CLK_TYPE_PERIPHERAL,
-};
-static struct clk ssc1_clk = {
- .name = "ssc1_clk",
- .pmc_mask = 1 << AT91SAM9263_ID_SSC1,
- .type = CLK_TYPE_PERIPHERAL,
-};
-static struct clk ac97_clk = {
- .name = "ac97_clk",
- .pmc_mask = 1 << AT91SAM9263_ID_AC97C,
- .type = CLK_TYPE_PERIPHERAL,
-};
-static struct clk tcb_clk = {
- .name = "tcb_clk",
- .pmc_mask = 1 << AT91SAM9263_ID_TCB,
- .type = CLK_TYPE_PERIPHERAL,
-};
-static struct clk pwm_clk = {
- .name = "pwm_clk",
- .pmc_mask = 1 << AT91SAM9263_ID_PWMC,
- .type = CLK_TYPE_PERIPHERAL,
-};
-static struct clk macb_clk = {
- .name = "pclk",
- .pmc_mask = 1 << AT91SAM9263_ID_EMAC,
- .type = CLK_TYPE_PERIPHERAL,
-};
-static struct clk dma_clk = {
- .name = "dma_clk",
- .pmc_mask = 1 << AT91SAM9263_ID_DMA,
- .type = CLK_TYPE_PERIPHERAL,
-};
-static struct clk twodge_clk = {
- .name = "2dge_clk",
- .pmc_mask = 1 << AT91SAM9263_ID_2DGE,
- .type = CLK_TYPE_PERIPHERAL,
-};
-static struct clk udc_clk = {
- .name = "udc_clk",
- .pmc_mask = 1 << AT91SAM9263_ID_UDP,
- .type = CLK_TYPE_PERIPHERAL,
-};
-static struct clk isi_clk = {
- .name = "isi_clk",
- .pmc_mask = 1 << AT91SAM9263_ID_ISI,
- .type = CLK_TYPE_PERIPHERAL,
-};
-static struct clk lcdc_clk = {
- .name = "lcdc_clk",
- .pmc_mask = 1 << AT91SAM9263_ID_LCDC,
- .type = CLK_TYPE_PERIPHERAL,
-};
-static struct clk ohci_clk = {
- .name = "ohci_clk",
- .pmc_mask = 1 << AT91SAM9263_ID_UHP,
- .type = CLK_TYPE_PERIPHERAL,
-};
-
-static struct clk *periph_clocks[] __initdata = {
- &pioA_clk,
- &pioB_clk,
- &pioCDE_clk,
- &usart0_clk,
- &usart1_clk,
- &usart2_clk,
- &mmc0_clk,
- &mmc1_clk,
- &can_clk,
- &twi_clk,
- &spi0_clk,
- &spi1_clk,
- &ssc0_clk,
- &ssc1_clk,
- &ac97_clk,
- &tcb_clk,
- &pwm_clk,
- &macb_clk,
- &twodge_clk,
- &udc_clk,
- &isi_clk,
- &lcdc_clk,
- &dma_clk,
- &ohci_clk,
- // irq0 .. irq1
-};
-
-static struct clk_lookup periph_clocks_lookups[] = {
- /* One additional fake clock for macb_hclk */
- CLKDEV_CON_ID("hclk", &macb_clk),
- CLKDEV_CON_DEV_ID("pclk", "at91rm9200_ssc.0", &ssc0_clk),
- CLKDEV_CON_DEV_ID("pclk", "at91rm9200_ssc.1", &ssc1_clk),
- CLKDEV_CON_DEV_ID("pclk", "fff98000.ssc", &ssc0_clk),
- CLKDEV_CON_DEV_ID("pclk", "fff9c000.ssc", &ssc1_clk),
- CLKDEV_CON_DEV_ID("hclk", "at91sam9263-lcdfb.0", &lcdc_clk),
- CLKDEV_CON_DEV_ID("mci_clk", "atmel_mci.0", &mmc0_clk),
- CLKDEV_CON_DEV_ID("mci_clk", "atmel_mci.1", &mmc1_clk),
- CLKDEV_CON_DEV_ID("spi_clk", "atmel_spi.0", &spi0_clk),
- CLKDEV_CON_DEV_ID("spi_clk", "atmel_spi.1", &spi1_clk),
- CLKDEV_CON_DEV_ID("t0_clk", "atmel_tcb.0", &tcb_clk),
- CLKDEV_CON_DEV_ID(NULL, "i2c-at91sam9260.0", &twi_clk),
- CLKDEV_CON_DEV_ID(NULL, "at91sam9rl-pwm", &pwm_clk),
- /* fake hclk clock */
- CLKDEV_CON_DEV_ID("hclk", "at91_ohci", &ohci_clk),
- CLKDEV_CON_ID("pioA", &pioA_clk),
- CLKDEV_CON_ID("pioB", &pioB_clk),
- CLKDEV_CON_ID("pioC", &pioCDE_clk),
- CLKDEV_CON_ID("pioD", &pioCDE_clk),
- CLKDEV_CON_ID("pioE", &pioCDE_clk),
- /* more usart lookup table for DT entries */
- CLKDEV_CON_DEV_ID("usart", "ffffee00.serial", &mck),
- CLKDEV_CON_DEV_ID("usart", "fff8c000.serial", &usart0_clk),
- CLKDEV_CON_DEV_ID("usart", "fff90000.serial", &usart1_clk),
- CLKDEV_CON_DEV_ID("usart", "fff94000.serial", &usart2_clk),
- /* more tc lookup table for DT entries */
- CLKDEV_CON_DEV_ID("t0_clk", "fff7c000.timer", &tcb_clk),
- CLKDEV_CON_DEV_ID("hclk", "a00000.ohci", &ohci_clk),
- CLKDEV_CON_DEV_ID("spi_clk", "fffa4000.spi", &spi0_clk),
- CLKDEV_CON_DEV_ID("spi_clk", "fffa8000.spi", &spi1_clk),
- CLKDEV_CON_DEV_ID("mci_clk", "fff80000.mmc", &mmc0_clk),
- CLKDEV_CON_DEV_ID("mci_clk", "fff84000.mmc", &mmc1_clk),
- CLKDEV_CON_DEV_ID(NULL, "fff88000.i2c", &twi_clk),
- CLKDEV_CON_DEV_ID(NULL, "fffff200.gpio", &pioA_clk),
- CLKDEV_CON_DEV_ID(NULL, "fffff400.gpio", &pioB_clk),
- CLKDEV_CON_DEV_ID(NULL, "fffff600.gpio", &pioCDE_clk),
- CLKDEV_CON_DEV_ID(NULL, "fffff800.gpio", &pioCDE_clk),
- CLKDEV_CON_DEV_ID(NULL, "fffffa00.gpio", &pioCDE_clk),
- CLKDEV_CON_DEV_ID(NULL, "fffb8000.pwm", &pwm_clk),
-};
-
-static struct clk_lookup usart_clocks_lookups[] = {
- CLKDEV_CON_DEV_ID("usart", "atmel_usart.0", &mck),
- CLKDEV_CON_DEV_ID("usart", "atmel_usart.1", &usart0_clk),
- CLKDEV_CON_DEV_ID("usart", "atmel_usart.2", &usart1_clk),
- CLKDEV_CON_DEV_ID("usart", "atmel_usart.3", &usart2_clk),
-};
-
-/*
- * The four programmable clocks.
- * You must configure pin multiplexing to bring these signals out.
- */
-static struct clk pck0 = {
- .name = "pck0",
- .pmc_mask = AT91_PMC_PCK0,
- .type = CLK_TYPE_PROGRAMMABLE,
- .id = 0,
-};
-static struct clk pck1 = {
- .name = "pck1",
- .pmc_mask = AT91_PMC_PCK1,
- .type = CLK_TYPE_PROGRAMMABLE,
- .id = 1,
-};
-static struct clk pck2 = {
- .name = "pck2",
- .pmc_mask = AT91_PMC_PCK2,
- .type = CLK_TYPE_PROGRAMMABLE,
- .id = 2,
-};
-static struct clk pck3 = {
- .name = "pck3",
- .pmc_mask = AT91_PMC_PCK3,
- .type = CLK_TYPE_PROGRAMMABLE,
- .id = 3,
-};
-
-static void __init at91sam9263_register_clocks(void)
-{
- int i;
-
- for (i = 0; i < ARRAY_SIZE(periph_clocks); i++)
- clk_register(periph_clocks[i]);
-
- clkdev_add_table(periph_clocks_lookups,
- ARRAY_SIZE(periph_clocks_lookups));
- clkdev_add_table(usart_clocks_lookups,
- ARRAY_SIZE(usart_clocks_lookups));
-
- clk_register(&pck0);
- clk_register(&pck1);
- clk_register(&pck2);
- clk_register(&pck3);
-}
-#else
-#define at91sam9263_register_clocks NULL
-#endif
-
-/* --------------------------------------------------------------------
- * GPIO
- * -------------------------------------------------------------------- */
-
-static struct at91_gpio_bank at91sam9263_gpio[] __initdata = {
- {
- .id = AT91SAM9263_ID_PIOA,
- .regbase = AT91SAM9263_BASE_PIOA,
- }, {
- .id = AT91SAM9263_ID_PIOB,
- .regbase = AT91SAM9263_BASE_PIOB,
- }, {
- .id = AT91SAM9263_ID_PIOCDE,
- .regbase = AT91SAM9263_BASE_PIOC,
- }, {
- .id = AT91SAM9263_ID_PIOCDE,
- .regbase = AT91SAM9263_BASE_PIOD,
- }, {
- .id = AT91SAM9263_ID_PIOCDE,
- .regbase = AT91SAM9263_BASE_PIOE,
- }
-};

/* --------------------------------------------------------------------
* AT91SAM9263 processor initialization
@@ -319,121 +26,15 @@ static void __init at91sam9263_map_io(void)
at91_init_sram(1, AT91SAM9263_SRAM1_BASE, AT91SAM9263_SRAM1_SIZE);
}

-static void __init at91sam9263_ioremap_registers(void)
-{
- at91_ioremap_ramc(0, AT91SAM9263_BASE_SDRAMC0, 512);
- at91_ioremap_ramc(1, AT91SAM9263_BASE_SDRAMC1, 512);
- at91sam926x_ioremap_pit(AT91SAM9263_BASE_PIT);
- at91sam9_ioremap_smc(0, AT91SAM9263_BASE_SMC0);
- at91sam9_ioremap_smc(1, AT91SAM9263_BASE_SMC1);
- at91_ioremap_matrix(AT91SAM9263_BASE_MATRIX);
- at91_pm_set_standby(at91sam9_sdram_standby);
-}
-
static void __init at91sam9263_initialize(void)
{
arm_pm_idle = at91sam9_idle;

at91_sysirq_mask_rtt(AT91SAM9263_BASE_RTT0);
at91_sysirq_mask_rtt(AT91SAM9263_BASE_RTT1);
-
- /* Register GPIO subsystem */
- at91_gpio_init(at91sam9263_gpio, 5);
-}
-
-static struct resource rstc_resources[] = {
- [0] = {
- .start = AT91SAM9263_BASE_RSTC,
- .end = AT91SAM9263_BASE_RSTC + SZ_16 - 1,
- .flags = IORESOURCE_MEM,
- },
- [1] = {
- .start = AT91SAM9263_BASE_SDRAMC0,
- .end = AT91SAM9263_BASE_SDRAMC0 + SZ_512 - 1,
- .flags = IORESOURCE_MEM,
- },
-};
-
-static struct platform_device rstc_device = {
- .name = "at91-sam9260-reset",
- .resource = rstc_resources,
- .num_resources = ARRAY_SIZE(rstc_resources),
-};
-
-static struct resource shdwc_resources[] = {
- [0] = {
- .start = AT91SAM9263_BASE_SHDWC,
- .end = AT91SAM9263_BASE_SHDWC + SZ_16 - 1,
- .flags = IORESOURCE_MEM,
- },
-};
-
-static struct platform_device shdwc_device = {
- .name = "at91-poweroff",
- .resource = shdwc_resources,
- .num_resources = ARRAY_SIZE(shdwc_resources),
-};
-
-static void __init at91sam9263_register_devices(void)
-{
- platform_device_register(&rstc_device);
- platform_device_register(&shdwc_device);
-}
-
-/* --------------------------------------------------------------------
- * Interrupt initialization
- * -------------------------------------------------------------------- */
-
-/*
- * The default interrupt priority levels (0 = lowest, 7 = highest).
- */
-static unsigned int at91sam9263_default_irq_priority[NR_AIC_IRQS] __initdata = {
- 7, /* Advanced Interrupt Controller (FIQ) */
- 7, /* System Peripherals */
- 1, /* Parallel IO Controller A */
- 1, /* Parallel IO Controller B */
- 1, /* Parallel IO Controller C, D and E */
- 0,
- 0,
- 5, /* USART 0 */
- 5, /* USART 1 */
- 5, /* USART 2 */
- 0, /* Multimedia Card Interface 0 */
- 0, /* Multimedia Card Interface 1 */
- 3, /* CAN */
- 6, /* Two-Wire Interface */
- 5, /* Serial Peripheral Interface 0 */
- 5, /* Serial Peripheral Interface 1 */
- 4, /* Serial Synchronous Controller 0 */
- 4, /* Serial Synchronous Controller 1 */
- 5, /* AC97 Controller */
- 0, /* Timer Counter 0, 1 and 2 */
- 0, /* Pulse Width Modulation Controller */
- 3, /* Ethernet */
- 0,
- 0, /* 2D Graphic Engine */
- 2, /* USB Device Port */
- 0, /* Image Sensor Interface */
- 3, /* LDC Controller */
- 0, /* DMA Controller */
- 0,
- 2, /* USB Host port */
- 0, /* Advanced Interrupt Controller (IRQ0) */
- 0, /* Advanced Interrupt Controller (IRQ1) */
-};
-
-static void __init at91sam9263_init_time(void)
-{
- at91sam926x_pit_init(NR_IRQS_LEGACY + AT91_ID_SYS);
}

AT91_SOC_START(at91sam9263)
.map_io = at91sam9263_map_io,
- .default_irq_priority = at91sam9263_default_irq_priority,
- .extern_irq = (1 << AT91SAM9263_ID_IRQ0) | (1 << AT91SAM9263_ID_IRQ1),
- .ioremap_registers = at91sam9263_ioremap_registers,
- .register_clocks = at91sam9263_register_clocks,
- .register_devices = at91sam9263_register_devices,
.init = at91sam9263_initialize,
- .init_time = at91sam9263_init_time,
AT91_SOC_END
diff --git a/arch/arm/mach-at91/at91sam9263_devices.c b/arch/arm/mach-at91/at91sam9263_devices.c
deleted file mode 100644
index cef0e2f57068..000000000000
--- a/arch/arm/mach-at91/at91sam9263_devices.c
+++ /dev/null
@@ -1,1538 +0,0 @@
-/*
- * arch/arm/mach-at91/at91sam9263_devices.c
- *
- * Copyright (C) 2007 Atmel Corporation.
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2 of the License, or
- * (at your option) any later version.
- *
- */
-#include <asm/mach/arch.h>
-#include <asm/mach/map.h>
-
-#include <linux/dma-mapping.h>
-#include <linux/gpio.h>
-#include <linux/platform_device.h>
-#include <linux/i2c-gpio.h>
-
-#include <linux/fb.h>
-#include <video/atmel_lcdc.h>
-
-#include <mach/at91sam9263.h>
-#include <mach/at91sam9263_matrix.h>
-#include <mach/at91_matrix.h>
-#include <mach/at91sam9_smc.h>
-#include <mach/hardware.h>
-
-#include "board.h"
-#include "generic.h"
-#include "gpio.h"
-
-
-/* --------------------------------------------------------------------
- * USB Host
- * -------------------------------------------------------------------- */
-
-#if defined(CONFIG_USB_OHCI_HCD) || defined(CONFIG_USB_OHCI_HCD_MODULE)
-static u64 ohci_dmamask = DMA_BIT_MASK(32);
-static struct at91_usbh_data usbh_data;
-
-static struct resource usbh_resources[] = {
- [0] = {
- .start = AT91SAM9263_UHP_BASE,
- .end = AT91SAM9263_UHP_BASE + SZ_1M - 1,
- .flags = IORESOURCE_MEM,
- },
- [1] = {
- .start = NR_IRQS_LEGACY + AT91SAM9263_ID_UHP,
- .end = NR_IRQS_LEGACY + AT91SAM9263_ID_UHP,
- .flags = IORESOURCE_IRQ,
- },
-};
-
-static struct platform_device at91_usbh_device = {
- .name = "at91_ohci",
- .id = -1,
- .dev = {
- .dma_mask = &ohci_dmamask,
- .coherent_dma_mask = DMA_BIT_MASK(32),
- .platform_data = &usbh_data,
- },
- .resource = usbh_resources,
- .num_resources = ARRAY_SIZE(usbh_resources),
-};
-
-void __init at91_add_device_usbh(struct at91_usbh_data *data)
-{
- int i;
-
- if (!data)
- return;
-
- /* Enable VBus control for UHP ports */
- for (i = 0; i < data->ports; i++) {
- if (gpio_is_valid(data->vbus_pin[i]))
- at91_set_gpio_output(data->vbus_pin[i],
- data->vbus_pin_active_low[i]);
- }
-
- /* Enable overcurrent notification */
- for (i = 0; i < data->ports; i++) {
- if (gpio_is_valid(data->overcurrent_pin[i]))
- at91_set_gpio_input(data->overcurrent_pin[i], 1);
- }
-
- usbh_data = *data;
- platform_device_register(&at91_usbh_device);
-}
-#else
-void __init at91_add_device_usbh(struct at91_usbh_data *data) {}
-#endif
-
-
-/* --------------------------------------------------------------------
- * USB Device (Gadget)
- * -------------------------------------------------------------------- */
-
-#if defined(CONFIG_USB_AT91) || defined(CONFIG_USB_AT91_MODULE)
-static struct at91_udc_data udc_data;
-
-static struct resource udc_resources[] = {
- [0] = {
- .start = AT91SAM9263_BASE_UDP,
- .end = AT91SAM9263_BASE_UDP + SZ_16K - 1,
- .flags = IORESOURCE_MEM,
- },
- [1] = {
- .start = NR_IRQS_LEGACY + AT91SAM9263_ID_UDP,
- .end = NR_IRQS_LEGACY + AT91SAM9263_ID_UDP,
- .flags = IORESOURCE_IRQ,
- },
-};
-
-static struct platform_device at91_udc_device = {
- .name = "at91_udc",
- .id = -1,
- .dev = {
- .platform_data = &udc_data,
- },
- .resource = udc_resources,
- .num_resources = ARRAY_SIZE(udc_resources),
-};
-
-void __init at91_add_device_udc(struct at91_udc_data *data)
-{
- if (!data)
- return;
-
- if (gpio_is_valid(data->vbus_pin)) {
- at91_set_gpio_input(data->vbus_pin, 0);
- at91_set_deglitch(data->vbus_pin, 1);
- }
-
- /* Pullup pin is handled internally by USB device peripheral */
-
- udc_data = *data;
- platform_device_register(&at91_udc_device);
-}
-#else
-void __init at91_add_device_udc(struct at91_udc_data *data) {}
-#endif
-
-
-/* --------------------------------------------------------------------
- * Ethernet
- * -------------------------------------------------------------------- */
-
-#if defined(CONFIG_MACB) || defined(CONFIG_MACB_MODULE)
-static u64 eth_dmamask = DMA_BIT_MASK(32);
-static struct macb_platform_data eth_data;
-
-static struct resource eth_resources[] = {
- [0] = {
- .start = AT91SAM9263_BASE_EMAC,
- .end = AT91SAM9263_BASE_EMAC + SZ_16K - 1,
- .flags = IORESOURCE_MEM,
- },
- [1] = {
- .start = NR_IRQS_LEGACY + AT91SAM9263_ID_EMAC,
- .end = NR_IRQS_LEGACY + AT91SAM9263_ID_EMAC,
- .flags = IORESOURCE_IRQ,
- },
-};
-
-static struct platform_device at91sam9263_eth_device = {
- .name = "macb",
- .id = -1,
- .dev = {
- .dma_mask = &eth_dmamask,
- .coherent_dma_mask = DMA_BIT_MASK(32),
- .platform_data = &eth_data,
- },
- .resource = eth_resources,
- .num_resources = ARRAY_SIZE(eth_resources),
-};
-
-void __init at91_add_device_eth(struct macb_platform_data *data)
-{
- if (!data)
- return;
-
- if (gpio_is_valid(data->phy_irq_pin)) {
- at91_set_gpio_input(data->phy_irq_pin, 0);
- at91_set_deglitch(data->phy_irq_pin, 1);
- }
-
- /* Pins used for MII and RMII */
- at91_set_A_periph(AT91_PIN_PE21, 0); /* ETXCK_EREFCK */
- at91_set_B_periph(AT91_PIN_PC25, 0); /* ERXDV */
- at91_set_A_periph(AT91_PIN_PE25, 0); /* ERX0 */
- at91_set_A_periph(AT91_PIN_PE26, 0); /* ERX1 */
- at91_set_A_periph(AT91_PIN_PE27, 0); /* ERXER */
- at91_set_A_periph(AT91_PIN_PE28, 0); /* ETXEN */
- at91_set_A_periph(AT91_PIN_PE23, 0); /* ETX0 */
- at91_set_A_periph(AT91_PIN_PE24, 0); /* ETX1 */
- at91_set_A_periph(AT91_PIN_PE30, 0); /* EMDIO */
- at91_set_A_periph(AT91_PIN_PE29, 0); /* EMDC */
-
- if (!data->is_rmii) {
- at91_set_A_periph(AT91_PIN_PE22, 0); /* ECRS */
- at91_set_B_periph(AT91_PIN_PC26, 0); /* ECOL */
- at91_set_B_periph(AT91_PIN_PC22, 0); /* ERX2 */
- at91_set_B_periph(AT91_PIN_PC23, 0); /* ERX3 */
- at91_set_B_periph(AT91_PIN_PC27, 0); /* ERXCK */
- at91_set_B_periph(AT91_PIN_PC20, 0); /* ETX2 */
- at91_set_B_periph(AT91_PIN_PC21, 0); /* ETX3 */
- at91_set_B_periph(AT91_PIN_PC24, 0); /* ETXER */
- }
-
- eth_data = *data;
- platform_device_register(&at91sam9263_eth_device);
-}
-#else
-void __init at91_add_device_eth(struct macb_platform_data *data) {}
-#endif
-
-
-/* --------------------------------------------------------------------
- * MMC / SD
- * -------------------------------------------------------------------- */
-
-#if IS_ENABLED(CONFIG_MMC_ATMELMCI)
-static u64 mmc_dmamask = DMA_BIT_MASK(32);
-static struct mci_platform_data mmc0_data, mmc1_data;
-
-static struct resource mmc0_resources[] = {
- [0] = {
- .start = AT91SAM9263_BASE_MCI0,
- .end = AT91SAM9263_BASE_MCI0 + SZ_16K - 1,
- .flags = IORESOURCE_MEM,
- },
- [1] = {
- .start = NR_IRQS_LEGACY + AT91SAM9263_ID_MCI0,
- .end = NR_IRQS_LEGACY + AT91SAM9263_ID_MCI0,
- .flags = IORESOURCE_IRQ,
- },
-};
-
-static struct platform_device at91sam9263_mmc0_device = {
- .name = "atmel_mci",
- .id = 0,
- .dev = {
- .dma_mask = &mmc_dmamask,
- .coherent_dma_mask = DMA_BIT_MASK(32),
- .platform_data = &mmc0_data,
- },
- .resource = mmc0_resources,
- .num_resources = ARRAY_SIZE(mmc0_resources),
-};
-
-static struct resource mmc1_resources[] = {
- [0] = {
- .start = AT91SAM9263_BASE_MCI1,
- .end = AT91SAM9263_BASE_MCI1 + SZ_16K - 1,
- .flags = IORESOURCE_MEM,
- },
- [1] = {
- .start = NR_IRQS_LEGACY + AT91SAM9263_ID_MCI1,
- .end = NR_IRQS_LEGACY + AT91SAM9263_ID_MCI1,
- .flags = IORESOURCE_IRQ,
- },
-};
-
-static struct platform_device at91sam9263_mmc1_device = {
- .name = "atmel_mci",
- .id = 1,
- .dev = {
- .dma_mask = &mmc_dmamask,
- .coherent_dma_mask = DMA_BIT_MASK(32),
- .platform_data = &mmc1_data,
- },
- .resource = mmc1_resources,
- .num_resources = ARRAY_SIZE(mmc1_resources),
-};
-
-void __init at91_add_device_mci(short mmc_id, struct mci_platform_data *data)
-{
- unsigned int i;
- unsigned int slot_count = 0;
-
- if (!data)
- return;
-
- for (i = 0; i < ATMCI_MAX_NR_SLOTS; i++) {
-
- if (!data->slot[i].bus_width)
- continue;
-
- /* input/irq */
- if (gpio_is_valid(data->slot[i].detect_pin)) {
- at91_set_gpio_input(data->slot[i].detect_pin,
- 1);
- at91_set_deglitch(data->slot[i].detect_pin,
- 1);
- }
- if (gpio_is_valid(data->slot[i].wp_pin))
- at91_set_gpio_input(data->slot[i].wp_pin, 1);
-
- if (mmc_id == 0) { /* MCI0 */
- switch (i) {
- case 0: /* slot A */
- /* CMD */
- at91_set_A_periph(AT91_PIN_PA1, 1);
- /* DAT0, maybe DAT1..DAT3 */
- at91_set_A_periph(AT91_PIN_PA0, 1);
- if (data->slot[i].bus_width == 4) {
- at91_set_A_periph(AT91_PIN_PA3, 1);
- at91_set_A_periph(AT91_PIN_PA4, 1);
- at91_set_A_periph(AT91_PIN_PA5, 1);
- }
- slot_count++;
- break;
- case 1: /* slot B */
- /* CMD */
- at91_set_A_periph(AT91_PIN_PA16, 1);
- /* DAT0, maybe DAT1..DAT3 */
- at91_set_A_periph(AT91_PIN_PA17, 1);
- if (data->slot[i].bus_width == 4) {
- at91_set_A_periph(AT91_PIN_PA18, 1);
- at91_set_A_periph(AT91_PIN_PA19, 1);
- at91_set_A_periph(AT91_PIN_PA20, 1);
- }
- slot_count++;
- break;
- default:
- printk(KERN_ERR
- "AT91: SD/MMC slot %d not available\n", i);
- break;
- }
- if (slot_count) {
- /* CLK */
- at91_set_A_periph(AT91_PIN_PA12, 0);
-
- mmc0_data = *data;
- platform_device_register(&at91sam9263_mmc0_device);
- }
- } else if (mmc_id == 1) { /* MCI1 */
- switch (i) {
- case 0: /* slot A */
- /* CMD */
- at91_set_A_periph(AT91_PIN_PA7, 1);
- /* DAT0, maybe DAT1..DAT3 */
- at91_set_A_periph(AT91_PIN_PA8, 1);
- if (data->slot[i].bus_width == 4) {
- at91_set_A_periph(AT91_PIN_PA9, 1);
- at91_set_A_periph(AT91_PIN_PA10, 1);
- at91_set_A_periph(AT91_PIN_PA11, 1);
- }
- slot_count++;
- break;
- case 1: /* slot B */
- /* CMD */
- at91_set_A_periph(AT91_PIN_PA21, 1);
- /* DAT0, maybe DAT1..DAT3 */
- at91_set_A_periph(AT91_PIN_PA22, 1);
- if (data->slot[i].bus_width == 4) {
- at91_set_A_periph(AT91_PIN_PA23, 1);
- at91_set_A_periph(AT91_PIN_PA24, 1);
- at91_set_A_periph(AT91_PIN_PA25, 1);
- }
- slot_count++;
- break;
- default:
- printk(KERN_ERR
- "AT91: SD/MMC slot %d not available\n", i);
- break;
- }
- if (slot_count) {
- /* CLK */
- at91_set_A_periph(AT91_PIN_PA6, 0);
-
- mmc1_data = *data;
- platform_device_register(&at91sam9263_mmc1_device);
- }
- }
- }
-}
-#else
-void __init at91_add_device_mci(short mmc_id, struct mci_platform_data *data) {}
-#endif
-
-/* --------------------------------------------------------------------
- * Compact Flash (PCMCIA or IDE)
- * -------------------------------------------------------------------- */
-
-#if defined(CONFIG_PATA_AT91) || defined(CONFIG_PATA_AT91_MODULE) || \
- defined(CONFIG_AT91_CF) || defined(CONFIG_AT91_CF_MODULE)
-
-static struct at91_cf_data cf0_data;
-
-static struct resource cf0_resources[] = {
- [0] = {
- .start = AT91_CHIPSELECT_4,
- .end = AT91_CHIPSELECT_4 + SZ_256M - 1,
- .flags = IORESOURCE_MEM | IORESOURCE_MEM_8AND16BIT,
- }
-};
-
-static struct platform_device cf0_device = {
- .id = 0,
- .dev = {
- .platform_data = &cf0_data,
- },
- .resource = cf0_resources,
- .num_resources = ARRAY_SIZE(cf0_resources),
-};
-
-static struct at91_cf_data cf1_data;
-
-static struct resource cf1_resources[] = {
- [0] = {
- .start = AT91_CHIPSELECT_5,
- .end = AT91_CHIPSELECT_5 + SZ_256M - 1,
- .flags = IORESOURCE_MEM | IORESOURCE_MEM_8AND16BIT,
- }
-};
-
-static struct platform_device cf1_device = {
- .id = 1,
- .dev = {
- .platform_data = &cf1_data,
- },
- .resource = cf1_resources,
- .num_resources = ARRAY_SIZE(cf1_resources),
-};
-
-void __init at91_add_device_cf(struct at91_cf_data *data)
-{
- unsigned long ebi0_csa;
- struct platform_device *pdev;
-
- if (!data)
- return;
-
- /*
- * assign CS4 or CS5 to SMC with Compact Flash logic support,
- * we assume SMC timings are configured by board code,
- * except True IDE where timings are controlled by driver
- */
- ebi0_csa = at91_matrix_read(AT91_MATRIX_EBI0CSA);
- switch (data->chipselect) {
- case 4:
- at91_set_A_periph(AT91_PIN_PD6, 0); /* EBI0_NCS4/CFCS0 */
- ebi0_csa |= AT91_MATRIX_EBI0_CS4A_SMC_CF1;
- cf0_data = *data;
- pdev = &cf0_device;
- break;
- case 5:
- at91_set_A_periph(AT91_PIN_PD7, 0); /* EBI0_NCS5/CFCS1 */
- ebi0_csa |= AT91_MATRIX_EBI0_CS5A_SMC_CF2;
- cf1_data = *data;
- pdev = &cf1_device;
- break;
- default:
- printk(KERN_ERR "AT91 CF: bad chip-select requested (%u)\n",
- data->chipselect);
- return;
- }
- at91_matrix_write(AT91_MATRIX_EBI0CSA, ebi0_csa);
-
- if (gpio_is_valid(data->det_pin)) {
- at91_set_gpio_input(data->det_pin, 1);
- at91_set_deglitch(data->det_pin, 1);
- }
-
- if (gpio_is_valid(data->irq_pin)) {
- at91_set_gpio_input(data->irq_pin, 1);
- at91_set_deglitch(data->irq_pin, 1);
- }
-
- if (gpio_is_valid(data->vcc_pin))
- /* initially off */
- at91_set_gpio_output(data->vcc_pin, 0);
-
- /* enable EBI controlled pins */
- at91_set_A_periph(AT91_PIN_PD5, 1); /* NWAIT */
- at91_set_A_periph(AT91_PIN_PD8, 0); /* CFCE1 */
- at91_set_A_periph(AT91_PIN_PD9, 0); /* CFCE2 */
- at91_set_A_periph(AT91_PIN_PD14, 0); /* CFNRW */
-
- pdev->name = (data->flags & AT91_CF_TRUE_IDE) ? "pata_at91" : "at91_cf";
- platform_device_register(pdev);
-}
-#else
-void __init at91_add_device_cf(struct at91_cf_data *data) {}
-#endif
-
-/* --------------------------------------------------------------------
- * NAND / SmartMedia
- * -------------------------------------------------------------------- */
-
-#if defined(CONFIG_MTD_NAND_ATMEL) || defined(CONFIG_MTD_NAND_ATMEL_MODULE)
-static struct atmel_nand_data nand_data;
-
-#define NAND_BASE AT91_CHIPSELECT_3
-
-static struct resource nand_resources[] = {
- [0] = {
- .start = NAND_BASE,
- .end = NAND_BASE + SZ_256M - 1,
- .flags = IORESOURCE_MEM,
- },
- [1] = {
- .start = AT91SAM9263_BASE_ECC0,
- .end = AT91SAM9263_BASE_ECC0 + SZ_512 - 1,
- .flags = IORESOURCE_MEM,
- }
-};
-
-static struct platform_device at91sam9263_nand_device = {
- .name = "atmel_nand",
- .id = -1,
- .dev = {
- .platform_data = &nand_data,
- },
- .resource = nand_resources,
- .num_resources = ARRAY_SIZE(nand_resources),
-};
-
-void __init at91_add_device_nand(struct atmel_nand_data *data)
-{
- unsigned long csa;
-
- if (!data)
- return;
-
- csa = at91_matrix_read(AT91_MATRIX_EBI0CSA);
- at91_matrix_write(AT91_MATRIX_EBI0CSA, csa | AT91_MATRIX_EBI0_CS3A_SMC_SMARTMEDIA);
-
- /* enable pin */
- if (gpio_is_valid(data->enable_pin))
- at91_set_gpio_output(data->enable_pin, 1);
-
- /* ready/busy pin */
- if (gpio_is_valid(data->rdy_pin))
- at91_set_gpio_input(data->rdy_pin, 1);
-
- /* card detect pin */
- if (gpio_is_valid(data->det_pin))
- at91_set_gpio_input(data->det_pin, 1);
-
- nand_data = *data;
- platform_device_register(&at91sam9263_nand_device);
-}
-#else
-void __init at91_add_device_nand(struct atmel_nand_data *data) {}
-#endif
-
-
-/* --------------------------------------------------------------------
- * TWI (i2c)
- * -------------------------------------------------------------------- */
-
-/*
- * Prefer the GPIO code since the TWI controller isn't robust
- * (gets overruns and underruns under load) and can only issue
- * repeated STARTs in one scenario (the driver doesn't yet handle them).
- */
-#if defined(CONFIG_I2C_GPIO) || defined(CONFIG_I2C_GPIO_MODULE)
-
-static struct i2c_gpio_platform_data pdata = {
- .sda_pin = AT91_PIN_PB4,
- .sda_is_open_drain = 1,
- .scl_pin = AT91_PIN_PB5,
- .scl_is_open_drain = 1,
- .udelay = 2, /* ~100 kHz */
-};
-
-static struct platform_device at91sam9263_twi_device = {
- .name = "i2c-gpio",
- .id = 0,
- .dev.platform_data = &pdata,
-};
-
-void __init at91_add_device_i2c(struct i2c_board_info *devices, int nr_devices)
-{
- at91_set_GPIO_periph(AT91_PIN_PB4, 1); /* TWD (SDA) */
- at91_set_multi_drive(AT91_PIN_PB4, 1);
-
- at91_set_GPIO_periph(AT91_PIN_PB5, 1); /* TWCK (SCL) */
- at91_set_multi_drive(AT91_PIN_PB5, 1);
-
- i2c_register_board_info(0, devices, nr_devices);
- platform_device_register(&at91sam9263_twi_device);
-}
-
-#elif defined(CONFIG_I2C_AT91) || defined(CONFIG_I2C_AT91_MODULE)
-
-static struct resource twi_resources[] = {
- [0] = {
- .start = AT91SAM9263_BASE_TWI,
- .end = AT91SAM9263_BASE_TWI + SZ_16K - 1,
- .flags = IORESOURCE_MEM,
- },
- [1] = {
- .start = NR_IRQS_LEGACY + AT91SAM9263_ID_TWI,
- .end = NR_IRQS_LEGACY + AT91SAM9263_ID_TWI,
- .flags = IORESOURCE_IRQ,
- },
-};
-
-static struct platform_device at91sam9263_twi_device = {
- .name = "i2c-at91sam9260",
- .id = 0,
- .resource = twi_resources,
- .num_resources = ARRAY_SIZE(twi_resources),
-};
-
-void __init at91_add_device_i2c(struct i2c_board_info *devices, int nr_devices)
-{
- /* pins used for TWI interface */
- at91_set_A_periph(AT91_PIN_PB4, 0); /* TWD */
- at91_set_multi_drive(AT91_PIN_PB4, 1);
-
- at91_set_A_periph(AT91_PIN_PB5, 0); /* TWCK */
- at91_set_multi_drive(AT91_PIN_PB5, 1);
-
- i2c_register_board_info(0, devices, nr_devices);
- platform_device_register(&at91sam9263_twi_device);
-}
-#else
-void __init at91_add_device_i2c(struct i2c_board_info *devices, int nr_devices) {}
-#endif
-
-
-/* --------------------------------------------------------------------
- * SPI
- * -------------------------------------------------------------------- */
-
-#if defined(CONFIG_SPI_ATMEL) || defined(CONFIG_SPI_ATMEL_MODULE)
-static u64 spi_dmamask = DMA_BIT_MASK(32);
-
-static struct resource spi0_resources[] = {
- [0] = {
- .start = AT91SAM9263_BASE_SPI0,
- .end = AT91SAM9263_BASE_SPI0 + SZ_16K - 1,
- .flags = IORESOURCE_MEM,
- },
- [1] = {
- .start = NR_IRQS_LEGACY + AT91SAM9263_ID_SPI0,
- .end = NR_IRQS_LEGACY + AT91SAM9263_ID_SPI0,
- .flags = IORESOURCE_IRQ,
- },
-};
-
-static struct platform_device at91sam9263_spi0_device = {
- .name = "atmel_spi",
- .id = 0,
- .dev = {
- .dma_mask = &spi_dmamask,
- .coherent_dma_mask = DMA_BIT_MASK(32),
- },
- .resource = spi0_resources,
- .num_resources = ARRAY_SIZE(spi0_resources),
-};
-
-static const unsigned spi0_standard_cs[4] = { AT91_PIN_PA5, AT91_PIN_PA3, AT91_PIN_PA4, AT91_PIN_PB11 };
-
-static struct resource spi1_resources[] = {
- [0] = {
- .start = AT91SAM9263_BASE_SPI1,
- .end = AT91SAM9263_BASE_SPI1 + SZ_16K - 1,
- .flags = IORESOURCE_MEM,
- },
- [1] = {
- .start = NR_IRQS_LEGACY + AT91SAM9263_ID_SPI1,
- .end = NR_IRQS_LEGACY + AT91SAM9263_ID_SPI1,
- .flags = IORESOURCE_IRQ,
- },
-};
-
-static struct platform_device at91sam9263_spi1_device = {
- .name = "atmel_spi",
- .id = 1,
- .dev = {
- .dma_mask = &spi_dmamask,
- .coherent_dma_mask = DMA_BIT_MASK(32),
- },
- .resource = spi1_resources,
- .num_resources = ARRAY_SIZE(spi1_resources),
-};
-
-static const unsigned spi1_standard_cs[4] = { AT91_PIN_PB15, AT91_PIN_PB16, AT91_PIN_PB17, AT91_PIN_PB18 };
-
-void __init at91_add_device_spi(struct spi_board_info *devices, int nr_devices)
-{
- int i;
- unsigned long cs_pin;
- short enable_spi0 = 0;
- short enable_spi1 = 0;
-
- /* Choose SPI chip-selects */
- for (i = 0; i < nr_devices; i++) {
- if (devices[i].controller_data)
- cs_pin = (unsigned long) devices[i].controller_data;
- else if (devices[i].bus_num == 0)
- cs_pin = spi0_standard_cs[devices[i].chip_select];
- else
- cs_pin = spi1_standard_cs[devices[i].chip_select];
-
- if (!gpio_is_valid(cs_pin))
- continue;
-
- if (devices[i].bus_num == 0)
- enable_spi0 = 1;
- else
- enable_spi1 = 1;
-
- /* enable chip-select pin */
- at91_set_gpio_output(cs_pin, 1);
-
- /* pass chip-select pin to driver */
- devices[i].controller_data = (void *) cs_pin;
- }
-
- spi_register_board_info(devices, nr_devices);
-
- /* Configure SPI bus(es) */
- if (enable_spi0) {
- at91_set_B_periph(AT91_PIN_PA0, 0); /* SPI0_MISO */
- at91_set_B_periph(AT91_PIN_PA1, 0); /* SPI0_MOSI */
- at91_set_B_periph(AT91_PIN_PA2, 0); /* SPI0_SPCK */
-
- platform_device_register(&at91sam9263_spi0_device);
- }
- if (enable_spi1) {
- at91_set_A_periph(AT91_PIN_PB12, 0); /* SPI1_MISO */
- at91_set_A_periph(AT91_PIN_PB13, 0); /* SPI1_MOSI */
- at91_set_A_periph(AT91_PIN_PB14, 0); /* SPI1_SPCK */
-
- platform_device_register(&at91sam9263_spi1_device);
- }
-}
-#else
-void __init at91_add_device_spi(struct spi_board_info *devices, int nr_devices) {}
-#endif
-
-
-/* --------------------------------------------------------------------
- * AC97
- * -------------------------------------------------------------------- */
-
-#if defined(CONFIG_SND_ATMEL_AC97C) || defined(CONFIG_SND_ATMEL_AC97C_MODULE)
-static u64 ac97_dmamask = DMA_BIT_MASK(32);
-static struct ac97c_platform_data ac97_data;
-
-static struct resource ac97_resources[] = {
- [0] = {
- .start = AT91SAM9263_BASE_AC97C,
- .end = AT91SAM9263_BASE_AC97C + SZ_16K - 1,
- .flags = IORESOURCE_MEM,
- },
- [1] = {
- .start = NR_IRQS_LEGACY + AT91SAM9263_ID_AC97C,
- .end = NR_IRQS_LEGACY + AT91SAM9263_ID_AC97C,
- .flags = IORESOURCE_IRQ,
- },
-};
-
-static struct platform_device at91sam9263_ac97_device = {
- .name = "atmel_ac97c",
- .id = 0,
- .dev = {
- .dma_mask = &ac97_dmamask,
- .coherent_dma_mask = DMA_BIT_MASK(32),
- .platform_data = &ac97_data,
- },
- .resource = ac97_resources,
- .num_resources = ARRAY_SIZE(ac97_resources),
-};
-
-void __init at91_add_device_ac97(struct ac97c_platform_data *data)
-{
- if (!data)
- return;
-
- at91_set_A_periph(AT91_PIN_PB0, 0); /* AC97FS */
- at91_set_A_periph(AT91_PIN_PB1, 0); /* AC97CK */
- at91_set_A_periph(AT91_PIN_PB2, 0); /* AC97TX */
- at91_set_A_periph(AT91_PIN_PB3, 0); /* AC97RX */
-
- /* reset */
- if (gpio_is_valid(data->reset_pin))
- at91_set_gpio_output(data->reset_pin, 0);
-
- ac97_data = *data;
- platform_device_register(&at91sam9263_ac97_device);
-}
-#else
-void __init at91_add_device_ac97(struct ac97c_platform_data *data) {}
-#endif
-
-/* --------------------------------------------------------------------
- * CAN Controller
- * -------------------------------------------------------------------- */
-
-#if defined(CONFIG_CAN_AT91) || defined(CONFIG_CAN_AT91_MODULE)
-static struct resource can_resources[] = {
- [0] = {
- .start = AT91SAM9263_BASE_CAN,
- .end = AT91SAM9263_BASE_CAN + SZ_16K - 1,
- .flags = IORESOURCE_MEM,
- },
- [1] = {
- .start = NR_IRQS_LEGACY + AT91SAM9263_ID_CAN,
- .end = NR_IRQS_LEGACY + AT91SAM9263_ID_CAN,
- .flags = IORESOURCE_IRQ,
- },
-};
-
-static struct platform_device at91sam9263_can_device = {
- .name = "at91_can",
- .id = -1,
- .resource = can_resources,
- .num_resources = ARRAY_SIZE(can_resources),
-};
-
-void __init at91_add_device_can(struct at91_can_data *data)
-{
- at91_set_A_periph(AT91_PIN_PA13, 0); /* CANTX */
- at91_set_A_periph(AT91_PIN_PA14, 0); /* CANRX */
- at91sam9263_can_device.dev.platform_data = data;
-
- platform_device_register(&at91sam9263_can_device);
-}
-#else
-void __init at91_add_device_can(struct at91_can_data *data) {}
-#endif
-
-/* --------------------------------------------------------------------
- * LCD Controller
- * -------------------------------------------------------------------- */
-
-#if defined(CONFIG_FB_ATMEL) || defined(CONFIG_FB_ATMEL_MODULE)
-static u64 lcdc_dmamask = DMA_BIT_MASK(32);
-static struct atmel_lcdfb_pdata lcdc_data;
-
-static struct resource lcdc_resources[] = {
- [0] = {
- .start = AT91SAM9263_LCDC_BASE,
- .end = AT91SAM9263_LCDC_BASE + SZ_4K - 1,
- .flags = IORESOURCE_MEM,
- },
- [1] = {
- .start = NR_IRQS_LEGACY + AT91SAM9263_ID_LCDC,
- .end = NR_IRQS_LEGACY + AT91SAM9263_ID_LCDC,
- .flags = IORESOURCE_IRQ,
- },
-};
-
-static struct platform_device at91_lcdc_device = {
- .name = "at91sam9263-lcdfb",
- .id = 0,
- .dev = {
- .dma_mask = &lcdc_dmamask,
- .coherent_dma_mask = DMA_BIT_MASK(32),
- .platform_data = &lcdc_data,
- },
- .resource = lcdc_resources,
- .num_resources = ARRAY_SIZE(lcdc_resources),
-};
-
-void __init at91_add_device_lcdc(struct atmel_lcdfb_pdata *data)
-{
- if (!data)
- return;
-
- at91_set_A_periph(AT91_PIN_PC1, 0); /* LCDHSYNC */
- at91_set_A_periph(AT91_PIN_PC2, 0); /* LCDDOTCK */
- at91_set_A_periph(AT91_PIN_PC3, 0); /* LCDDEN */
- at91_set_B_periph(AT91_PIN_PB9, 0); /* LCDCC */
- at91_set_A_periph(AT91_PIN_PC6, 0); /* LCDD2 */
- at91_set_A_periph(AT91_PIN_PC7, 0); /* LCDD3 */
- at91_set_A_periph(AT91_PIN_PC8, 0); /* LCDD4 */
- at91_set_A_periph(AT91_PIN_PC9, 0); /* LCDD5 */
- at91_set_A_periph(AT91_PIN_PC10, 0); /* LCDD6 */
- at91_set_A_periph(AT91_PIN_PC11, 0); /* LCDD7 */
- at91_set_A_periph(AT91_PIN_PC14, 0); /* LCDD10 */
- at91_set_A_periph(AT91_PIN_PC15, 0); /* LCDD11 */
- at91_set_A_periph(AT91_PIN_PC16, 0); /* LCDD12 */
- at91_set_B_periph(AT91_PIN_PC12, 0); /* LCDD13 */
- at91_set_A_periph(AT91_PIN_PC18, 0); /* LCDD14 */
- at91_set_A_periph(AT91_PIN_PC19, 0); /* LCDD15 */
- at91_set_A_periph(AT91_PIN_PC22, 0); /* LCDD18 */
- at91_set_A_periph(AT91_PIN_PC23, 0); /* LCDD19 */
- at91_set_A_periph(AT91_PIN_PC24, 0); /* LCDD20 */
- at91_set_B_periph(AT91_PIN_PC17, 0); /* LCDD21 */
- at91_set_A_periph(AT91_PIN_PC26, 0); /* LCDD22 */
- at91_set_A_periph(AT91_PIN_PC27, 0); /* LCDD23 */
-
- lcdc_data = *data;
- platform_device_register(&at91_lcdc_device);
-}
-#else
-void __init at91_add_device_lcdc(struct atmel_lcdfb_pdata *data) {}
-#endif
-
-
-/* --------------------------------------------------------------------
- * Image Sensor Interface
- * -------------------------------------------------------------------- */
-
-#if defined(CONFIG_VIDEO_AT91_ISI) || defined(CONFIG_VIDEO_AT91_ISI_MODULE)
-
-struct resource isi_resources[] = {
- [0] = {
- .start = AT91SAM9263_BASE_ISI,
- .end = AT91SAM9263_BASE_ISI + SZ_16K - 1,
- .flags = IORESOURCE_MEM,
- },
- [1] = {
- .start = NR_IRQS_LEGACY + AT91SAM9263_ID_ISI,
- .end = NR_IRQS_LEGACY + AT91SAM9263_ID_ISI,
- .flags = IORESOURCE_IRQ,
- },
-};
-
-static struct platform_device at91sam9263_isi_device = {
- .name = "at91_isi",
- .id = -1,
- .resource = isi_resources,
- .num_resources = ARRAY_SIZE(isi_resources),
-};
-
-void __init at91_add_device_isi(struct isi_platform_data *data,
- bool use_pck_as_mck)
-{
- at91_set_A_periph(AT91_PIN_PE0, 0); /* ISI_D0 */
- at91_set_A_periph(AT91_PIN_PE1, 0); /* ISI_D1 */
- at91_set_A_periph(AT91_PIN_PE2, 0); /* ISI_D2 */
- at91_set_A_periph(AT91_PIN_PE3, 0); /* ISI_D3 */
- at91_set_A_periph(AT91_PIN_PE4, 0); /* ISI_D4 */
- at91_set_A_periph(AT91_PIN_PE5, 0); /* ISI_D5 */
- at91_set_A_periph(AT91_PIN_PE6, 0); /* ISI_D6 */
- at91_set_A_periph(AT91_PIN_PE7, 0); /* ISI_D7 */
- at91_set_A_periph(AT91_PIN_PE8, 0); /* ISI_PCK */
- at91_set_A_periph(AT91_PIN_PE9, 0); /* ISI_HSYNC */
- at91_set_A_periph(AT91_PIN_PE10, 0); /* ISI_VSYNC */
- at91_set_B_periph(AT91_PIN_PE12, 0); /* ISI_PD8 */
- at91_set_B_periph(AT91_PIN_PE13, 0); /* ISI_PD9 */
- at91_set_B_periph(AT91_PIN_PE14, 0); /* ISI_PD10 */
- at91_set_B_periph(AT91_PIN_PE15, 0); /* ISI_PD11 */
-
- if (use_pck_as_mck) {
- at91_set_B_periph(AT91_PIN_PE11, 0); /* ISI_MCK (PCK3) */
-
- /* TODO: register the PCK for ISI_MCK and set its parent */
- }
-}
-#else
-void __init at91_add_device_isi(struct isi_platform_data *data,
- bool use_pck_as_mck) {}
-#endif
-
-
-/* --------------------------------------------------------------------
- * Timer/Counter block
- * -------------------------------------------------------------------- */
-
-#ifdef CONFIG_ATMEL_TCLIB
-
-static struct resource tcb_resources[] = {
- [0] = {
- .start = AT91SAM9263_BASE_TCB0,
- .end = AT91SAM9263_BASE_TCB0 + SZ_16K - 1,
- .flags = IORESOURCE_MEM,
- },
- [1] = {
- .start = NR_IRQS_LEGACY + AT91SAM9263_ID_TCB,
- .end = NR_IRQS_LEGACY + AT91SAM9263_ID_TCB,
- .flags = IORESOURCE_IRQ,
- },
-};
-
-static struct platform_device at91sam9263_tcb_device = {
- .name = "atmel_tcb",
- .id = 0,
- .resource = tcb_resources,
- .num_resources = ARRAY_SIZE(tcb_resources),
-};
-
-#if defined(CONFIG_OF)
-static struct of_device_id tcb_ids[] = {
- { .compatible = "atmel,at91rm9200-tcb" },
- { /*sentinel*/ }
-};
-#endif
-
-static void __init at91_add_device_tc(void)
-{
-#if defined(CONFIG_OF)
- struct device_node *np;
-
- np = of_find_matching_node(NULL, tcb_ids);
- if (np) {
- of_node_put(np);
- return;
- }
-#endif
-
- platform_device_register(&at91sam9263_tcb_device);
-}
-#else
-static void __init at91_add_device_tc(void) { }
-#endif
-
-
-/* --------------------------------------------------------------------
- * RTT
- * -------------------------------------------------------------------- */
-
-static struct resource rtt0_resources[] = {
- {
- .start = AT91SAM9263_BASE_RTT0,
- .end = AT91SAM9263_BASE_RTT0 + SZ_16 - 1,
- .flags = IORESOURCE_MEM,
- }, {
- .flags = IORESOURCE_MEM,
- }, {
- .flags = IORESOURCE_IRQ,
- }
-};
-
-static struct platform_device at91sam9263_rtt0_device = {
- .name = "at91_rtt",
- .id = 0,
- .resource = rtt0_resources,
-};
-
-static struct resource rtt1_resources[] = {
- {
- .start = AT91SAM9263_BASE_RTT1,
- .end = AT91SAM9263_BASE_RTT1 + SZ_16 - 1,
- .flags = IORESOURCE_MEM,
- }, {
- .flags = IORESOURCE_MEM,
- }, {
- .flags = IORESOURCE_IRQ,
- }
-};
-
-static struct platform_device at91sam9263_rtt1_device = {
- .name = "at91_rtt",
- .id = 1,
- .resource = rtt1_resources,
-};
-
-#if IS_ENABLED(CONFIG_RTC_DRV_AT91SAM9)
-static void __init at91_add_device_rtt_rtc(void)
-{
- struct platform_device *pdev;
- struct resource *r;
-
- switch (CONFIG_RTC_DRV_AT91SAM9_RTT) {
- case 0:
- /*
- * The second resource is needed only for the chosen RTT:
- * GPBR will serve as the storage for RTC time offset
- */
- at91sam9263_rtt0_device.num_resources = 3;
- at91sam9263_rtt1_device.num_resources = 1;
- pdev = &at91sam9263_rtt0_device;
- r = rtt0_resources;
- break;
- case 1:
- at91sam9263_rtt0_device.num_resources = 1;
- at91sam9263_rtt1_device.num_resources = 3;
- pdev = &at91sam9263_rtt1_device;
- r = rtt1_resources;
- break;
- default:
- pr_err("at91sam9263: only supports 2 RTT (%d)\n",
- CONFIG_RTC_DRV_AT91SAM9_RTT);
- return;
- }
-
- pdev->name = "rtc-at91sam9";
- r[1].start = AT91SAM9263_BASE_GPBR + 4 * CONFIG_RTC_DRV_AT91SAM9_GPBR;
- r[1].end = r[1].start + 3;
- r[2].start = NR_IRQS_LEGACY + AT91_ID_SYS;
- r[2].end = NR_IRQS_LEGACY + AT91_ID_SYS;
-}
-#else
-static void __init at91_add_device_rtt_rtc(void)
-{
- /* Only one resource is needed: RTT not used as RTC */
- at91sam9263_rtt0_device.num_resources = 1;
- at91sam9263_rtt1_device.num_resources = 1;
-}
-#endif
-
-static void __init at91_add_device_rtt(void)
-{
- at91_add_device_rtt_rtc();
- platform_device_register(&at91sam9263_rtt0_device);
- platform_device_register(&at91sam9263_rtt1_device);
-}
-
-
-/* --------------------------------------------------------------------
- * Watchdog
- * -------------------------------------------------------------------- */
-
-#if defined(CONFIG_AT91SAM9X_WATCHDOG) || defined(CONFIG_AT91SAM9X_WATCHDOG_MODULE)
-static struct resource wdt_resources[] = {
- {
- .start = AT91SAM9263_BASE_WDT,
- .end = AT91SAM9263_BASE_WDT + SZ_16 - 1,
- .flags = IORESOURCE_MEM,
- }
-};
-
-static struct platform_device at91sam9263_wdt_device = {
- .name = "at91_wdt",
- .id = -1,
- .resource = wdt_resources,
- .num_resources = ARRAY_SIZE(wdt_resources),
-};
-
-static void __init at91_add_device_watchdog(void)
-{
- platform_device_register(&at91sam9263_wdt_device);
-}
-#else
-static void __init at91_add_device_watchdog(void) {}
-#endif
-
-
-/* --------------------------------------------------------------------
- * PWM
- * --------------------------------------------------------------------*/
-
-#if IS_ENABLED(CONFIG_PWM_ATMEL)
-static struct resource pwm_resources[] = {
- [0] = {
- .start = AT91SAM9263_BASE_PWMC,
- .end = AT91SAM9263_BASE_PWMC + SZ_16K - 1,
- .flags = IORESOURCE_MEM,
- },
- [1] = {
- .start = NR_IRQS_LEGACY + AT91SAM9263_ID_PWMC,
- .end = NR_IRQS_LEGACY + AT91SAM9263_ID_PWMC,
- .flags = IORESOURCE_IRQ,
- },
-};
-
-static struct platform_device at91sam9263_pwm0_device = {
- .name = "at91sam9rl-pwm",
- .id = -1,
- .resource = pwm_resources,
- .num_resources = ARRAY_SIZE(pwm_resources),
-};
-
-void __init at91_add_device_pwm(u32 mask)
-{
- if (mask & (1 << AT91_PWM0))
- at91_set_B_periph(AT91_PIN_PB7, 1); /* enable PWM0 */
-
- if (mask & (1 << AT91_PWM1))
- at91_set_B_periph(AT91_PIN_PB8, 1); /* enable PWM1 */
-
- if (mask & (1 << AT91_PWM2))
- at91_set_B_periph(AT91_PIN_PC29, 1); /* enable PWM2 */
-
- if (mask & (1 << AT91_PWM3))
- at91_set_B_periph(AT91_PIN_PB29, 1); /* enable PWM3 */
-
- platform_device_register(&at91sam9263_pwm0_device);
-}
-#else
-void __init at91_add_device_pwm(u32 mask) {}
-#endif
-
-
-/* --------------------------------------------------------------------
- * SSC -- Synchronous Serial Controller
- * -------------------------------------------------------------------- */
-
-#if defined(CONFIG_ATMEL_SSC) || defined(CONFIG_ATMEL_SSC_MODULE)
-static u64 ssc0_dmamask = DMA_BIT_MASK(32);
-
-static struct resource ssc0_resources[] = {
- [0] = {
- .start = AT91SAM9263_BASE_SSC0,
- .end = AT91SAM9263_BASE_SSC0 + SZ_16K - 1,
- .flags = IORESOURCE_MEM,
- },
- [1] = {
- .start = NR_IRQS_LEGACY + AT91SAM9263_ID_SSC0,
- .end = NR_IRQS_LEGACY + AT91SAM9263_ID_SSC0,
- .flags = IORESOURCE_IRQ,
- },
-};
-
-static struct platform_device at91sam9263_ssc0_device = {
- .name = "at91rm9200_ssc",
- .id = 0,
- .dev = {
- .dma_mask = &ssc0_dmamask,
- .coherent_dma_mask = DMA_BIT_MASK(32),
- },
- .resource = ssc0_resources,
- .num_resources = ARRAY_SIZE(ssc0_resources),
-};
-
-static inline void configure_ssc0_pins(unsigned pins)
-{
- if (pins & ATMEL_SSC_TF)
- at91_set_B_periph(AT91_PIN_PB0, 1);
- if (pins & ATMEL_SSC_TK)
- at91_set_B_periph(AT91_PIN_PB1, 1);
- if (pins & ATMEL_SSC_TD)
- at91_set_B_periph(AT91_PIN_PB2, 1);
- if (pins & ATMEL_SSC_RD)
- at91_set_B_periph(AT91_PIN_PB3, 1);
- if (pins & ATMEL_SSC_RK)
- at91_set_B_periph(AT91_PIN_PB4, 1);
- if (pins & ATMEL_SSC_RF)
- at91_set_B_periph(AT91_PIN_PB5, 1);
-}
-
-static u64 ssc1_dmamask = DMA_BIT_MASK(32);
-
-static struct resource ssc1_resources[] = {
- [0] = {
- .start = AT91SAM9263_BASE_SSC1,
- .end = AT91SAM9263_BASE_SSC1 + SZ_16K - 1,
- .flags = IORESOURCE_MEM,
- },
- [1] = {
- .start = NR_IRQS_LEGACY + AT91SAM9263_ID_SSC1,
- .end = NR_IRQS_LEGACY + AT91SAM9263_ID_SSC1,
- .flags = IORESOURCE_IRQ,
- },
-};
-
-static struct platform_device at91sam9263_ssc1_device = {
- .name = "at91rm9200_ssc",
- .id = 1,
- .dev = {
- .dma_mask = &ssc1_dmamask,
- .coherent_dma_mask = DMA_BIT_MASK(32),
- },
- .resource = ssc1_resources,
- .num_resources = ARRAY_SIZE(ssc1_resources),
-};
-
-static inline void configure_ssc1_pins(unsigned pins)
-{
- if (pins & ATMEL_SSC_TF)
- at91_set_A_periph(AT91_PIN_PB6, 1);
- if (pins & ATMEL_SSC_TK)
- at91_set_A_periph(AT91_PIN_PB7, 1);
- if (pins & ATMEL_SSC_TD)
- at91_set_A_periph(AT91_PIN_PB8, 1);
- if (pins & ATMEL_SSC_RD)
- at91_set_A_periph(AT91_PIN_PB9, 1);
- if (pins & ATMEL_SSC_RK)
- at91_set_A_periph(AT91_PIN_PB10, 1);
- if (pins & ATMEL_SSC_RF)
- at91_set_A_periph(AT91_PIN_PB11, 1);
-}
-
-/*
- * SSC controllers are accessed through library code, instead of any
- * kind of all-singing/all-dancing driver. For example one could be
- * used by a particular I2S audio codec's driver, while another one
- * on the same system might be used by a custom data capture driver.
- */
-void __init at91_add_device_ssc(unsigned id, unsigned pins)
-{
- struct platform_device *pdev;
-
- /*
- * NOTE: caller is responsible for passing information matching
- * "pins" to whatever will be using each particular controller.
- */
- switch (id) {
- case AT91SAM9263_ID_SSC0:
- pdev = &at91sam9263_ssc0_device;
- configure_ssc0_pins(pins);
- break;
- case AT91SAM9263_ID_SSC1:
- pdev = &at91sam9263_ssc1_device;
- configure_ssc1_pins(pins);
- break;
- default:
- return;
- }
-
- platform_device_register(pdev);
-}
-
-#else
-void __init at91_add_device_ssc(unsigned id, unsigned pins) {}
-#endif
-
-
-/* --------------------------------------------------------------------
- * UART
- * -------------------------------------------------------------------- */
-
-#if defined(CONFIG_SERIAL_ATMEL)
-
-static struct resource dbgu_resources[] = {
- [0] = {
- .start = AT91SAM9263_BASE_DBGU,
- .end = AT91SAM9263_BASE_DBGU + SZ_512 - 1,
- .flags = IORESOURCE_MEM,
- },
- [1] = {
- .start = NR_IRQS_LEGACY + AT91_ID_SYS,
- .end = NR_IRQS_LEGACY + AT91_ID_SYS,
- .flags = IORESOURCE_IRQ,
- },
-};
-
-static struct atmel_uart_data dbgu_data = {
- .use_dma_tx = 0,
- .use_dma_rx = 0, /* DBGU not capable of receive DMA */
-};
-
-static u64 dbgu_dmamask = DMA_BIT_MASK(32);
-
-static struct platform_device at91sam9263_dbgu_device = {
- .name = "atmel_usart",
- .id = 0,
- .dev = {
- .dma_mask = &dbgu_dmamask,
- .coherent_dma_mask = DMA_BIT_MASK(32),
- .platform_data = &dbgu_data,
- },
- .resource = dbgu_resources,
- .num_resources = ARRAY_SIZE(dbgu_resources),
-};
-
-static inline void configure_dbgu_pins(void)
-{
- at91_set_A_periph(AT91_PIN_PC30, 0); /* DRXD */
- at91_set_A_periph(AT91_PIN_PC31, 1); /* DTXD */
-}
-
-static struct resource uart0_resources[] = {
- [0] = {
- .start = AT91SAM9263_BASE_US0,
- .end = AT91SAM9263_BASE_US0 + SZ_16K - 1,
- .flags = IORESOURCE_MEM,
- },
- [1] = {
- .start = NR_IRQS_LEGACY + AT91SAM9263_ID_US0,
- .end = NR_IRQS_LEGACY + AT91SAM9263_ID_US0,
- .flags = IORESOURCE_IRQ,
- },
-};
-
-static struct atmel_uart_data uart0_data = {
- .use_dma_tx = 1,
- .use_dma_rx = 1,
-};
-
-static u64 uart0_dmamask = DMA_BIT_MASK(32);
-
-static struct platform_device at91sam9263_uart0_device = {
- .name = "atmel_usart",
- .id = 1,
- .dev = {
- .dma_mask = &uart0_dmamask,
- .coherent_dma_mask = DMA_BIT_MASK(32),
- .platform_data = &uart0_data,
- },
- .resource = uart0_resources,
- .num_resources = ARRAY_SIZE(uart0_resources),
-};
-
-static inline void configure_usart0_pins(unsigned pins)
-{
- at91_set_A_periph(AT91_PIN_PA26, 1); /* TXD0 */
- at91_set_A_periph(AT91_PIN_PA27, 0); /* RXD0 */
-
- if (pins & ATMEL_UART_RTS)
- at91_set_A_periph(AT91_PIN_PA28, 0); /* RTS0 */
- if (pins & ATMEL_UART_CTS)
- at91_set_A_periph(AT91_PIN_PA29, 0); /* CTS0 */
-}
-
-static struct resource uart1_resources[] = {
- [0] = {
- .start = AT91SAM9263_BASE_US1,
- .end = AT91SAM9263_BASE_US1 + SZ_16K - 1,
- .flags = IORESOURCE_MEM,
- },
- [1] = {
- .start = NR_IRQS_LEGACY + AT91SAM9263_ID_US1,
- .end = NR_IRQS_LEGACY + AT91SAM9263_ID_US1,
- .flags = IORESOURCE_IRQ,
- },
-};
-
-static struct atmel_uart_data uart1_data = {
- .use_dma_tx = 1,
- .use_dma_rx = 1,
-};
-
-static u64 uart1_dmamask = DMA_BIT_MASK(32);
-
-static struct platform_device at91sam9263_uart1_device = {
- .name = "atmel_usart",
- .id = 2,
- .dev = {
- .dma_mask = &uart1_dmamask,
- .coherent_dma_mask = DMA_BIT_MASK(32),
- .platform_data = &uart1_data,
- },
- .resource = uart1_resources,
- .num_resources = ARRAY_SIZE(uart1_resources),
-};
-
-static inline void configure_usart1_pins(unsigned pins)
-{
- at91_set_A_periph(AT91_PIN_PD0, 1); /* TXD1 */
- at91_set_A_periph(AT91_PIN_PD1, 0); /* RXD1 */
-
- if (pins & ATMEL_UART_RTS)
- at91_set_B_periph(AT91_PIN_PD7, 0); /* RTS1 */
- if (pins & ATMEL_UART_CTS)
- at91_set_B_periph(AT91_PIN_PD8, 0); /* CTS1 */
-}
-
-static struct resource uart2_resources[] = {
- [0] = {
- .start = AT91SAM9263_BASE_US2,
- .end = AT91SAM9263_BASE_US2 + SZ_16K - 1,
- .flags = IORESOURCE_MEM,
- },
- [1] = {
- .start = NR_IRQS_LEGACY + AT91SAM9263_ID_US2,
- .end = NR_IRQS_LEGACY + AT91SAM9263_ID_US2,
- .flags = IORESOURCE_IRQ,
- },
-};
-
-static struct atmel_uart_data uart2_data = {
- .use_dma_tx = 1,
- .use_dma_rx = 1,
-};
-
-static u64 uart2_dmamask = DMA_BIT_MASK(32);
-
-static struct platform_device at91sam9263_uart2_device = {
- .name = "atmel_usart",
- .id = 3,
- .dev = {
- .dma_mask = &uart2_dmamask,
- .coherent_dma_mask = DMA_BIT_MASK(32),
- .platform_data = &uart2_data,
- },
- .resource = uart2_resources,
- .num_resources = ARRAY_SIZE(uart2_resources),
-};
-
-static inline void configure_usart2_pins(unsigned pins)
-{
- at91_set_A_periph(AT91_PIN_PD2, 1); /* TXD2 */
- at91_set_A_periph(AT91_PIN_PD3, 0); /* RXD2 */
-
- if (pins & ATMEL_UART_RTS)
- at91_set_B_periph(AT91_PIN_PD5, 0); /* RTS2 */
- if (pins & ATMEL_UART_CTS)
- at91_set_B_periph(AT91_PIN_PD6, 0); /* CTS2 */
-}
-
-static struct platform_device *__initdata at91_uarts[ATMEL_MAX_UART]; /* the UARTs to use */
-
-void __init at91_register_uart(unsigned id, unsigned portnr, unsigned pins)
-{
- struct platform_device *pdev;
- struct atmel_uart_data *pdata;
-
- switch (id) {
- case 0: /* DBGU */
- pdev = &at91sam9263_dbgu_device;
- configure_dbgu_pins();
- break;
- case AT91SAM9263_ID_US0:
- pdev = &at91sam9263_uart0_device;
- configure_usart0_pins(pins);
- break;
- case AT91SAM9263_ID_US1:
- pdev = &at91sam9263_uart1_device;
- configure_usart1_pins(pins);
- break;
- case AT91SAM9263_ID_US2:
- pdev = &at91sam9263_uart2_device;
- configure_usart2_pins(pins);
- break;
- default:
- return;
- }
- pdata = pdev->dev.platform_data;
- pdata->num = portnr; /* update to mapped ID */
-
- if (portnr < ATMEL_MAX_UART)
- at91_uarts[portnr] = pdev;
-}
-
-void __init at91_add_device_serial(void)
-{
- int i;
-
- for (i = 0; i < ATMEL_MAX_UART; i++) {
- if (at91_uarts[i])
- platform_device_register(at91_uarts[i]);
- }
-}
-#else
-void __init at91_register_uart(unsigned id, unsigned portnr, unsigned pins) {}
-void __init at91_add_device_serial(void) {}
-#endif
-
-
-/* -------------------------------------------------------------------- */
-/*
- * These devices are always present and don't need any board-specific
- * setup.
- */
-static int __init at91_add_standard_devices(void)
-{
- if (of_have_populated_dt())
- return 0;
-
- at91_add_device_rtt();
- at91_add_device_watchdog();
- at91_add_device_tc();
- return 0;
-}
-
-arch_initcall(at91_add_standard_devices);
diff --git a/arch/arm/mach-at91/board-sam9263ek.c b/arch/arm/mach-at91/board-sam9263ek.c
deleted file mode 100644
index d76680f2a209..000000000000
--- a/arch/arm/mach-at91/board-sam9263ek.c
+++ /dev/null
@@ -1,493 +0,0 @@
-/*
- * linux/arch/arm/mach-at91/board-sam9263ek.c
- *
- * Copyright (C) 2005 SAN People
- * Copyright (C) 2007 Atmel Corporation.
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2 of the License, or
- * (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
- */
-
-#include <linux/types.h>
-#include <linux/gpio.h>
-#include <linux/init.h>
-#include <linux/mm.h>
-#include <linux/module.h>
-#include <linux/platform_device.h>
-#include <linux/spi/spi.h>
-#include <linux/spi/ads7846.h>
-#include <linux/platform_data/at24.h>
-#include <linux/fb.h>
-#include <linux/gpio_keys.h>
-#include <linux/input.h>
-#include <linux/leds.h>
-#include <linux/pwm.h>
-#include <linux/leds_pwm.h>
-
-#include <video/atmel_lcdc.h>
-
-#include <asm/setup.h>
-#include <asm/mach-types.h>
-#include <asm/irq.h>
-
-#include <asm/mach/arch.h>
-#include <asm/mach/map.h>
-#include <asm/mach/irq.h>
-
-#include <mach/hardware.h>
-#include <mach/at91sam9_smc.h>
-#include <mach/system_rev.h>
-
-#include "at91_aic.h"
-#include "board.h"
-#include "sam9_smc.h"
-#include "generic.h"
-#include "gpio.h"
-
-
-static void __init ek_init_early(void)
-{
- /* Initialize processor: 16.367 MHz crystal */
- at91_initialize(16367660);
-}
-
-/*
- * USB Host port
- */
-static struct at91_usbh_data __initdata ek_usbh_data = {
- .ports = 2,
- .vbus_pin = { AT91_PIN_PA24, AT91_PIN_PA21 },
- .vbus_pin_active_low = {1, 1},
- .overcurrent_pin= {-EINVAL, -EINVAL},
-};
-
-/*
- * USB Device port
- */
-static struct at91_udc_data __initdata ek_udc_data = {
- .vbus_pin = AT91_PIN_PA25,
- .pullup_pin = -EINVAL, /* pull-up driven by UDC */
-};
-
-
-/*
- * ADS7846 Touchscreen
- */
-#if defined(CONFIG_TOUCHSCREEN_ADS7846) || defined(CONFIG_TOUCHSCREEN_ADS7846_MODULE)
-static int ads7843_pendown_state(void)
-{
- return !at91_get_gpio_value(AT91_PIN_PA15); /* Touchscreen PENIRQ */
-}
-
-static struct ads7846_platform_data ads_info = {
- .model = 7843,
- .x_min = 150,
- .x_max = 3830,
- .y_min = 190,
- .y_max = 3830,
- .vref_delay_usecs = 100,
- .x_plate_ohms = 450,
- .y_plate_ohms = 250,
- .pressure_max = 15000,
- .debounce_max = 1,
- .debounce_rep = 0,
- .debounce_tol = (~0),
- .get_pendown_state = ads7843_pendown_state,
-};
-
-static void __init ek_add_device_ts(void)
-{
- at91_set_B_periph(AT91_PIN_PA15, 1); /* External IRQ1, with pullup */
- at91_set_gpio_input(AT91_PIN_PA31, 1); /* Touchscreen BUSY signal */
-}
-#else
-static void __init ek_add_device_ts(void) {}
-#endif
-
-/*
- * SPI devices.
- */
-static struct spi_board_info ek_spi_devices[] = {
-#if defined(CONFIG_MTD_AT91_DATAFLASH_CARD)
- { /* DataFlash card */
- .modalias = "mtd_dataflash",
- .chip_select = 0,
- .max_speed_hz = 15 * 1000 * 1000,
- .bus_num = 0,
- },
-#endif
-#if defined(CONFIG_TOUCHSCREEN_ADS7846) || defined(CONFIG_TOUCHSCREEN_ADS7846_MODULE)
- {
- .modalias = "ads7846",
- .chip_select = 3,
- .max_speed_hz = 125000 * 26, /* (max sample rate @ 3V) * (cmd + data + overhead) */
- .bus_num = 0,
- .platform_data = &ads_info,
- .irq = NR_IRQS_LEGACY + AT91SAM9263_ID_IRQ1,
- },
-#endif
-};
-
-
-/*
- * MCI (SD/MMC)
- */
-static struct mci_platform_data __initdata mci1_data = {
- .slot[0] = {
- .bus_width = 4,
- .detect_pin = AT91_PIN_PE18,
- .wp_pin = AT91_PIN_PE19,
- },
-};
-
-
-/*
- * MACB Ethernet device
- */
-static struct macb_platform_data __initdata ek_macb_data = {
- .phy_irq_pin = AT91_PIN_PE31,
- .is_rmii = 1,
-};
-
-
-/*
- * NAND flash
- */
-static struct mtd_partition __initdata ek_nand_partition[] = {
- {
- .name = "Partition 1",
- .offset = 0,
- .size = SZ_64M,
- },
- {
- .name = "Partition 2",
- .offset = MTDPART_OFS_NXTBLK,
- .size = MTDPART_SIZ_FULL,
- },
-};
-
-static struct atmel_nand_data __initdata ek_nand_data = {
- .ale = 21,
- .cle = 22,
- .det_pin = -EINVAL,
- .rdy_pin = AT91_PIN_PA22,
- .enable_pin = AT91_PIN_PD15,
- .ecc_mode = NAND_ECC_SOFT,
- .on_flash_bbt = 1,
- .parts = ek_nand_partition,
- .num_parts = ARRAY_SIZE(ek_nand_partition),
-};
-
-static struct sam9_smc_config __initdata ek_nand_smc_config = {
- .ncs_read_setup = 0,
- .nrd_setup = 1,
- .ncs_write_setup = 0,
- .nwe_setup = 1,
-
- .ncs_read_pulse = 3,
- .nrd_pulse = 3,
- .ncs_write_pulse = 3,
- .nwe_pulse = 3,
-
- .read_cycle = 5,
- .write_cycle = 5,
-
- .mode = AT91_SMC_READMODE | AT91_SMC_WRITEMODE | AT91_SMC_EXNWMODE_DISABLE,
- .tdf_cycles = 2,
-};
-
-static void __init ek_add_device_nand(void)
-{
- ek_nand_data.bus_width_16 = board_have_nand_16bit();
- /* setup bus-width (8 or 16) */
- if (ek_nand_data.bus_width_16)
- ek_nand_smc_config.mode |= AT91_SMC_DBW_16;
- else
- ek_nand_smc_config.mode |= AT91_SMC_DBW_8;
-
- /* configure chip-select 3 (NAND) */
- sam9_smc_configure(0, 3, &ek_nand_smc_config);
-
- at91_add_device_nand(&ek_nand_data);
-}
-
-
-/*
- * I2C devices
- */
-static struct at24_platform_data at24c512 = {
- .byte_len = SZ_512K / 8,
- .page_size = 128,
- .flags = AT24_FLAG_ADDR16,
-};
-
-
-static struct i2c_board_info __initdata ek_i2c_devices[] = {
- {
- I2C_BOARD_INFO("24c512", 0x50),
- .platform_data = &at24c512,
- },
- /* more devices can be added using expansion connectors */
-};
-
-/*
- * LCD Controller
- */
-#if defined(CONFIG_FB_ATMEL) || defined(CONFIG_FB_ATMEL_MODULE)
-static struct fb_videomode at91_tft_vga_modes[] = {
- {
- .name = "TX09D50VM1CCA @ 60",
- .refresh = 60,
- .xres = 240, .yres = 320,
- .pixclock = KHZ2PICOS(4965),
-
- .left_margin = 1, .right_margin = 33,
- .upper_margin = 1, .lower_margin = 0,
- .hsync_len = 5, .vsync_len = 1,
-
- .sync = FB_SYNC_HOR_HIGH_ACT | FB_SYNC_VERT_HIGH_ACT,
- .vmode = FB_VMODE_NONINTERLACED,
- },
-};
-
-static struct fb_monspecs at91fb_default_monspecs = {
- .manufacturer = "HIT",
- .monitor = "TX09D70VM1CCA",
-
- .modedb = at91_tft_vga_modes,
- .modedb_len = ARRAY_SIZE(at91_tft_vga_modes),
- .hfmin = 15000,
- .hfmax = 64000,
- .vfmin = 50,
- .vfmax = 150,
-};
-
-#define AT91SAM9263_DEFAULT_LCDCON2 (ATMEL_LCDC_MEMOR_LITTLE \
- | ATMEL_LCDC_DISTYPE_TFT \
- | ATMEL_LCDC_CLKMOD_ALWAYSACTIVE)
-
-static void at91_lcdc_power_control(struct atmel_lcdfb_pdata *pdata, int on)
-{
- at91_set_gpio_value(AT91_PIN_PA30, on);
-}
-
-/* Driver datas */
-static struct atmel_lcdfb_pdata __initdata ek_lcdc_data = {
- .lcdcon_is_backlight = true,
- .default_bpp = 16,
- .default_dmacon = ATMEL_LCDC_DMAEN,
- .default_lcdcon2 = AT91SAM9263_DEFAULT_LCDCON2,
- .default_monspecs = &at91fb_default_monspecs,
- .atmel_lcdfb_power_control = at91_lcdc_power_control,
- .guard_time = 1,
-};
-
-#else
-static struct atmel_lcdfb_pdata __initdata ek_lcdc_data;
-#endif
-
-
-/*
- * GPIO Buttons
- */
-#if defined(CONFIG_KEYBOARD_GPIO) || defined(CONFIG_KEYBOARD_GPIO_MODULE)
-static struct gpio_keys_button ek_buttons[] = {
- { /* BP1, "leftclic" */
- .code = BTN_LEFT,
- .gpio = AT91_PIN_PC5,
- .active_low = 1,
- .desc = "left_click",
- .wakeup = 1,
- },
- { /* BP2, "rightclic" */
- .code = BTN_RIGHT,
- .gpio = AT91_PIN_PC4,
- .active_low = 1,
- .desc = "right_click",
- .wakeup = 1,
- }
-};
-
-static struct gpio_keys_platform_data ek_button_data = {
- .buttons = ek_buttons,
- .nbuttons = ARRAY_SIZE(ek_buttons),
-};
-
-static struct platform_device ek_button_device = {
- .name = "gpio-keys",
- .id = -1,
- .num_resources = 0,
- .dev = {
- .platform_data = &ek_button_data,
- }
-};
-
-static void __init ek_add_device_buttons(void)
-{
- at91_set_GPIO_periph(AT91_PIN_PC5, 1); /* left button */
- at91_set_deglitch(AT91_PIN_PC5, 1);
- at91_set_GPIO_periph(AT91_PIN_PC4, 1); /* right button */
- at91_set_deglitch(AT91_PIN_PC4, 1);
-
- platform_device_register(&ek_button_device);
-}
-#else
-static void __init ek_add_device_buttons(void) {}
-#endif
-
-
-/*
- * AC97
- * reset_pin is not connected: NRST
- */
-static struct ac97c_platform_data ek_ac97_data = {
- .reset_pin = -EINVAL,
-};
-
-
-/*
- * LEDs ... these could all be PWM-driven, for variable brightness
- */
-static struct gpio_led ek_leds[] = {
- { /* "right" led, green, userled2 (could be driven by pwm2) */
- .name = "ds2",
- .gpio = AT91_PIN_PC29,
- .active_low = 1,
- .default_trigger = "nand-disk",
- },
- { /* "power" led, yellow (could be driven by pwm0) */
- .name = "ds3",
- .gpio = AT91_PIN_PB7,
- .default_trigger = "heartbeat",
- },
-#if !IS_ENABLED(CONFIG_LEDS_PWM)
- {
- .name = "ds1",
- .gpio = AT91_PIN_PB8,
- .active_low = 1,
- .default_trigger = "none",
- }
-#endif
-};
-
-/*
- * PWM Leds
- */
-static struct pwm_lookup pwm_lookup[] = {
- PWM_LOOKUP("at91sam9rl-pwm", 1, "leds_pwm", "ds1",
- 5000, PWM_POLARITY_INVERSED),
-};
-
-#if IS_ENABLED(CONFIG_LEDS_PWM)
-static struct led_pwm pwm_leds[] = {
- {
- .name = "ds1",
- .max_brightness = 255,
- },
-};
-
-static struct led_pwm_platform_data pwm_data = {
- .num_leds = ARRAY_SIZE(pwm_leds),
- .leds = pwm_leds,
-};
-
-static struct platform_device leds_pwm = {
- .name = "leds_pwm",
- .id = -1,
- .dev = {
- .platform_data = &pwm_data,
- },
-};
-#endif
-
-
-/*
- * CAN
- */
-static void sam9263ek_transceiver_switch(int on)
-{
- if (on) {
- at91_set_gpio_output(AT91_PIN_PA18, 1); /* CANRXEN */
- at91_set_gpio_output(AT91_PIN_PA19, 0); /* CANRS */
- } else {
- at91_set_gpio_output(AT91_PIN_PA18, 0); /* CANRXEN */
- at91_set_gpio_output(AT91_PIN_PA19, 1); /* CANRS */
- }
-}
-
-static struct at91_can_data ek_can_data = {
- .transceiver_switch = sam9263ek_transceiver_switch,
-};
-
-static struct platform_device *devices[] __initdata = {
-#if IS_ENABLED(CONFIG_LEDS_PWM)
- &leds_pwm,
-#endif
-};
-
-static void __init ek_board_init(void)
-{
- at91_register_devices();
-
- /* Serial */
- /* DBGU on ttyS0. (Rx & Tx only) */
- at91_register_uart(0, 0, 0);
-
- /* USART0 on ttyS1. (Rx, Tx, RTS, CTS) */
- at91_register_uart(AT91SAM9263_ID_US0, 1, ATMEL_UART_CTS | ATMEL_UART_RTS);
- at91_add_device_serial();
- /* USB Host */
- at91_add_device_usbh(&ek_usbh_data);
- /* USB Device */
- at91_add_device_udc(&ek_udc_data);
- /* SPI */
- at91_set_gpio_output(AT91_PIN_PE20, 1); /* select spi0 clock */
- at91_add_device_spi(ek_spi_devices, ARRAY_SIZE(ek_spi_devices));
- /* Touchscreen */
- ek_add_device_ts();
- /* MMC */
- at91_add_device_mci(1, &mci1_data);
- /* Ethernet */
- at91_add_device_eth(&ek_macb_data);
- /* NAND */
- ek_add_device_nand();
- /* I2C */
- at91_add_device_i2c(ek_i2c_devices, ARRAY_SIZE(ek_i2c_devices));
- /* LCD Controller */
- at91_add_device_lcdc(&ek_lcdc_data);
- /* Push Buttons */
- ek_add_device_buttons();
- /* AC97 */
- at91_add_device_ac97(&ek_ac97_data);
- /* LEDs */
- at91_gpio_leds(ek_leds, ARRAY_SIZE(ek_leds));
- pwm_add_table(pwm_lookup, ARRAY_SIZE(pwm_lookup));
-#if IS_ENABLED(CONFIG_LEDS_PWM)
- at91_add_device_pwm(1 << AT91_PWM1);
-#endif
- /* CAN */
- at91_add_device_can(&ek_can_data);
- /* Other platform devices */
- platform_add_devices(devices, ARRAY_SIZE(devices));
-}
-
-MACHINE_START(AT91SAM9263EK, "Atmel AT91SAM9263-EK")
- /* Maintainer: Atmel */
- .init_time = at91_init_time,
- .map_io = at91_map_io,
- .handle_irq = at91_aic_handle_irq,
- .init_early = ek_init_early,
- .init_irq = at91_init_irq_default,
- .init_machine = ek_board_init,
-MACHINE_END
--
2.1.3