linux-kernel.vger.kernel.org archive mirror
 help / color / mirror / Atom feed
From: Heikki Krogerus <heikki.krogerus@linux.intel.com>
To: Felipe Balbi <balbi@ti.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>,
	David Cohen <david.a.cohen@linux.intel.com>,
	Stephen Boyd <sboyd@codeaurora.org>,
	Baolu Lu <baolu.lu@linux.intel.com>,
	linux-usb@vger.kernel.org, linux-kernel@vger.kernel.org
Subject: [PATCHv2 10/12] usb: dwc3: add ULPI interface support
Date: Wed, 18 Mar 2015 14:40:31 +0200	[thread overview]
Message-ID: <1426682433-133813-11-git-send-email-heikki.krogerus@linux.intel.com> (raw)
In-Reply-To: <1426682433-133813-1-git-send-email-heikki.krogerus@linux.intel.com>

Registers DWC3's ULPI interface with the ULPI bus when it's
available.

Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
---
 drivers/usb/dwc3/Kconfig  |  7 ++++
 drivers/usb/dwc3/Makefile |  4 +++
 drivers/usb/dwc3/core.c   | 14 ++++++++
 drivers/usb/dwc3/core.h   | 14 ++++++++
 drivers/usb/dwc3/ulpi.c   | 91 +++++++++++++++++++++++++++++++++++++++++++++++
 5 files changed, 130 insertions(+)
 create mode 100644 drivers/usb/dwc3/ulpi.c

diff --git a/drivers/usb/dwc3/Kconfig b/drivers/usb/dwc3/Kconfig
index 827c4f8..324bed7 100644
--- a/drivers/usb/dwc3/Kconfig
+++ b/drivers/usb/dwc3/Kconfig
@@ -11,6 +11,13 @@ config USB_DWC3
 
 if USB_DWC3
 
+config USB_DWC3_ULPI
+	bool "Register ULPI PHY Interface"
+	depends on USB_ULPI_BUS=y
+	help
+	  Select this if you have ULPI type PHY attached to your DWC3
+	  controller.
+
 choice
 	bool "DWC3 Mode Selection"
 	default USB_DWC3_DUAL_ROLE if (USB && USB_GADGET)
diff --git a/drivers/usb/dwc3/Makefile b/drivers/usb/dwc3/Makefile
index 46172f4..c7076e3 100644
--- a/drivers/usb/dwc3/Makefile
+++ b/drivers/usb/dwc3/Makefile
@@ -15,6 +15,10 @@ ifneq ($(filter y,$(CONFIG_USB_DWC3_GADGET) $(CONFIG_USB_DWC3_DUAL_ROLE)),)
 	dwc3-y				+= gadget.o ep0.o
 endif
 
+ifneq ($(CONFIG_USB_DWC3_ULPI),)
+	dwc3-y				+= ulpi.o
+endif
+
 ifneq ($(CONFIG_DEBUG_FS),)
 	dwc3-y				+= debugfs.o
 endif
diff --git a/drivers/usb/dwc3/core.c b/drivers/usb/dwc3/core.c
index b229ba1..4dce614 100644
--- a/drivers/usb/dwc3/core.c
+++ b/drivers/usb/dwc3/core.c
@@ -444,13 +444,25 @@ static int dwc3_phy_setup(struct dwc3 *dwc)
 	case DWC3_GHWPARAMS3_HSPHY_IFC_UTMI_ULPI:
 		if (!strncmp(dwc->hsphy_interface, "utmi", 4)) {
 			reg &= ~DWC3_GUSB2PHYCFG_ULPI_UTMI;
+			break;
 		} else if (!strncmp(dwc->hsphy_interface, "ulpi", 4)) {
 			reg |= DWC3_GUSB2PHYCFG_ULPI_UTMI;
+			dwc3_writel(dwc->regs, DWC3_GUSB2PHYCFG(0), reg);
 		} else {
 			dev_err(dwc->dev, "HSPHY Interface not defined\n");
 			return -EINVAL;
 		}
 		/* FALLTHROUGH */
+	case DWC3_GHWPARAMS3_HSPHY_IFC_ULPI:
+		/* Soft reset here to sync the clocks */
+		ret = dwc3_soft_reset(dwc);
+		if (ret)
+			return ret;
+
+		ret = dwc3_ulpi_init(dwc);
+		if (ret)
+			return ret;
+		/* FALLTHROUGH */
 	default:
 		break;
 	}
@@ -999,6 +1011,7 @@ err2:
 
 err1:
 	dwc3_free_event_buffers(dwc);
+	dwc3_ulpi_exit(dwc);
 
 err0:
 	/*
@@ -1034,6 +1047,7 @@ static int dwc3_remove(struct platform_device *pdev)
 	phy_power_off(dwc->usb3_generic_phy);
 
 	dwc3_core_exit(dwc);
+	dwc3_ulpi_exit(dwc);
 
 	pm_runtime_put_sync(&pdev->dev);
 	pm_runtime_disable(&pdev->dev);
diff --git a/drivers/usb/dwc3/core.h b/drivers/usb/dwc3/core.h
index 7b3ab64..d70da20 100644
--- a/drivers/usb/dwc3/core.h
+++ b/drivers/usb/dwc3/core.h
@@ -30,6 +30,7 @@
 #include <linux/usb/ch9.h>
 #include <linux/usb/gadget.h>
 #include <linux/usb/otg.h>
+#include <linux/ulpi/interface.h>
 
 #include <linux/phy/phy.h>
 
@@ -661,6 +662,7 @@ struct dwc3_scratchpad_array {
  * @usb3_phy: pointer to USB3 PHY
  * @usb2_generic_phy: pointer to USB2 PHY
  * @usb3_generic_phy: pointer to USB3 PHY
+ * @ulpi: pointer to ulpi interface
  * @dcfg: saved contents of DCFG register
  * @gctl: saved contents of GCTL register
  * @isoch_delay: wValue from Set Isochronous Delay request;
@@ -749,6 +751,8 @@ struct dwc3 {
 	struct phy		*usb2_generic_phy;
 	struct phy		*usb3_generic_phy;
 
+	struct ulpi		*ulpi;
+
 	void __iomem		*regs;
 	size_t			regs_size;
 
@@ -1047,4 +1051,14 @@ static inline int dwc3_gadget_resume(struct dwc3 *dwc)
 }
 #endif /* !IS_ENABLED(CONFIG_USB_DWC3_HOST) */
 
+#if IS_ENABLED(CONFIG_USB_DWC3_ULPI)
+int dwc3_ulpi_init(struct dwc3 *dwc);
+void dwc3_ulpi_exit(struct dwc3 *dwc);
+#else
+static inline int dwc3_ulpi_init(struct dwc3 *dwc)
+{ return 0; }
+static inline void dwc3_ulpi_exit(struct dwc3 *dwc)
+{ }
+#endif
+
 #endif /* __DRIVERS_USB_DWC3_CORE_H */
diff --git a/drivers/usb/dwc3/ulpi.c b/drivers/usb/dwc3/ulpi.c
new file mode 100644
index 0000000..4dfcc81
--- /dev/null
+++ b/drivers/usb/dwc3/ulpi.c
@@ -0,0 +1,91 @@
+/**
+ * ulpi.c - DesignWare USB3 Controller's ULPI PHY interface
+ *
+ * Copyright (C) 2015 Intel Corporation
+ *
+ * Author: Heikki Krogerus <heikki.krogerus@linux.intel.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#include <linux/ulpi/regs.h>
+
+#include "core.h"
+#include "io.h"
+
+#define DWC3_ULPI_ADDR(a) \
+		((a >= ULPI_EXT_VENDOR_SPECIFIC) ? \
+		DWC3_GUSB2PHYACC_ADDR(ULPI_ACCESS_EXTENDED) | \
+		DWC3_GUSB2PHYACC_EXTEND_ADDR(a) : DWC3_GUSB2PHYACC_ADDR(a))
+
+static int dwc3_ulpi_busyloop(struct dwc3 *dwc)
+{
+	unsigned count = 1000;
+	u32 reg;
+
+	while (count--) {
+		reg = dwc3_readl(dwc->regs, DWC3_GUSB2PHYACC(0));
+		if (!(reg & DWC3_GUSB2PHYACC_BUSY))
+			return 0;
+		cpu_relax();
+	}
+
+	return -ETIMEDOUT;
+}
+
+static int dwc3_ulpi_read(struct ulpi_ops *ops, u8 addr)
+{
+	struct dwc3 *dwc = dev_get_drvdata(ops->dev);
+	u32 reg;
+	int ret;
+
+	reg = DWC3_GUSB2PHYACC_NEWREGREQ | DWC3_ULPI_ADDR(addr);
+	dwc3_writel(dwc->regs, DWC3_GUSB2PHYACC(0), reg);
+
+	ret = dwc3_ulpi_busyloop(dwc);
+	if (ret)
+		return ret;
+
+	reg = dwc3_readl(dwc->regs, DWC3_GUSB2PHYACC(0));
+
+	return DWC3_GUSB2PHYACC_DATA(reg);
+}
+
+static int dwc3_ulpi_write(struct ulpi_ops *ops, u8 addr, u8 val)
+{
+	struct dwc3 *dwc = dev_get_drvdata(ops->dev);
+	u32 reg;
+
+	reg = DWC3_GUSB2PHYACC_NEWREGREQ | DWC3_ULPI_ADDR(addr);
+	reg |= DWC3_GUSB2PHYACC_WRITE | val;
+	dwc3_writel(dwc->regs, DWC3_GUSB2PHYACC(0), reg);
+
+	return dwc3_ulpi_busyloop(dwc);
+}
+
+static struct ulpi_ops dwc3_ulpi = {
+	.read = dwc3_ulpi_read,
+	.write = dwc3_ulpi_write,
+};
+
+int dwc3_ulpi_init(struct dwc3 *dwc)
+{
+	/* Register the interface */
+	dwc->ulpi = ulpi_register_interface(dwc->dev, &dwc3_ulpi);
+	if (IS_ERR(dwc->ulpi)) {
+		dev_err(dwc->dev, "failed to register ULPI interface");
+		return PTR_ERR(dwc->ulpi);
+	}
+
+	return 0;
+}
+
+void dwc3_ulpi_exit(struct dwc3 *dwc)
+{
+	if (dwc->ulpi) {
+		ulpi_unregister_interface(dwc->ulpi);
+		dwc->ulpi = NULL;
+	}
+}
-- 
2.1.4


  parent reply	other threads:[~2015-03-18 12:43 UTC|newest]

Thread overview: 30+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2015-03-18 12:40 [PATCHv2 00/12] usb: ulpi bus Heikki Krogerus
2015-03-18 12:40 ` [PATCHv2 01/12] usb: add bus type for USB ULPI Heikki Krogerus
2015-03-18 23:26   ` Paul Bolle
2015-03-19 11:44     ` Heikki Krogerus
2015-03-20 12:20       ` [PATCHv3 " Heikki Krogerus
2015-03-26 14:02         ` [PATCHv4 " Heikki Krogerus
2015-03-23  7:16   ` [PATCHv2 " Lu, Baolu
2015-03-23 10:57     ` Heikki Krogerus
2015-03-18 12:40 ` [PATCHv2 02/12] usb: dwc3: USB2 PHY register access bits Heikki Krogerus
2015-03-18 12:40 ` [PATCHv2 03/12] usb: dwc3: ULPI or UTMI+ select Heikki Krogerus
2015-03-18 12:40 ` [PATCHv2 04/12] usb: dwc3: store driver data earlier Heikki Krogerus
2015-03-18 12:40 ` [PATCHv2 05/12] usb: dwc3: cache hwparams earlier Heikki Krogerus
2015-03-18 12:40 ` [PATCHv2 06/12] usb: dwc3: soft reset to it's own function Heikki Krogerus
2015-03-18 12:40 ` [PATCHv2 07/12] usb: dwc3: setup phys earlier Heikki Krogerus
2015-03-18 12:40 ` [PATCHv2 08/12] usb: dwc3: add hsphy_interface property Heikki Krogerus
2015-03-18 12:40 ` [PATCHv2 09/12] usb: dwc3: pci: add quirk for Baytrails Heikki Krogerus
2015-03-18 17:08   ` David Cohen
2015-03-19 11:51     ` Heikki Krogerus
2015-03-20 12:20       ` [PATCHv3 " Heikki Krogerus
2015-03-18 12:40 ` Heikki Krogerus [this message]
2015-03-18 22:53   ` [PATCHv2 10/12] usb: dwc3: add ULPI interface support Paul Bolle
2015-03-19 11:48     ` Heikki Krogerus
2015-03-20 12:20       ` [PATCHv3 " Heikki Krogerus
2015-03-18 12:40 ` [PATCHv2 11/12] phy: helpers for USB ULPI PHY registering Heikki Krogerus
2015-03-18 14:46   ` Sergei Shtylyov
2015-03-18 16:54     ` David Cohen
2015-03-18 18:02       ` Sergei Shtylyov
2015-03-18 12:40 ` [PATCHv2 12/12] phy: add driver for TI TUSB1210 ULPI PHY Heikki Krogerus
2015-03-18 17:12 ` [PATCHv2 00/12] usb: ulpi bus David Cohen
2015-03-18 17:19   ` David Cohen

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=1426682433-133813-11-git-send-email-heikki.krogerus@linux.intel.com \
    --to=heikki.krogerus@linux.intel.com \
    --cc=balbi@ti.com \
    --cc=baolu.lu@linux.intel.com \
    --cc=david.a.cohen@linux.intel.com \
    --cc=gregkh@linuxfoundation.org \
    --cc=linux-kernel@vger.kernel.org \
    --cc=linux-usb@vger.kernel.org \
    --cc=sboyd@codeaurora.org \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).