From: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
To: lee.jones@linaro.org
Cc: broonie@kernel.org, lgirdwood@gmail.com, sameo@linux.intel.com,
patches@opensource.wolfsonmicro.com,
linux-kernel@vger.kernel.org
Subject: [RESEND PATCH v3 09/10] mfd: arizona: Add better support for system suspend
Date: Mon, 11 May 2015 13:58:09 +0100 [thread overview]
Message-ID: <1431349090-24173-10-git-send-email-ckeepax@opensource.wolfsonmicro.com> (raw)
In-Reply-To: <1431349090-24173-1-git-send-email-ckeepax@opensource.wolfsonmicro.com>
Allow the chip to completely power off if we enter runtime suspend and
there is no jack detection active. This is helpful for systems where
system suspend might remove the supplies to the CODEC, without informing
us. Note the powering off is done in runtime suspend rather than system
suspend, because we need to hold reset until the first time DCVDD is
powered anyway (which would be in runtime resume), and we might as well
save the extra power.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
---
drivers/mfd/arizona-core.c | 94 +++++++++++++++++++++++++++++++-------
include/linux/mfd/arizona/core.h | 1 +
2 files changed, 78 insertions(+), 17 deletions(-)
diff --git a/drivers/mfd/arizona-core.c b/drivers/mfd/arizona-core.c
index 93024ac..f1ff68a 100644
--- a/drivers/mfd/arizona-core.c
+++ b/drivers/mfd/arizona-core.c
@@ -442,12 +442,33 @@ static int arizona_runtime_resume(struct device *dev)
dev_dbg(arizona->dev, "Leaving AoD mode\n");
+ if (arizona->has_fully_powered_off) {
+ dev_dbg(arizona->dev, "Re-enabling core supplies\n");
+
+ ret = regulator_bulk_enable(arizona->num_core_supplies,
+ arizona->core_supplies);
+ if (ret) {
+ dev_err(dev, "Failed to enable core supplies: %d\n",
+ ret);
+ return ret;
+ }
+ }
+
ret = regulator_enable(arizona->dcvdd);
if (ret != 0) {
dev_err(arizona->dev, "Failed to enable DCVDD: %d\n", ret);
+ if (arizona->has_fully_powered_off)
+ regulator_bulk_disable(arizona->num_core_supplies,
+ arizona->core_supplies);
return ret;
}
+ if (arizona->has_fully_powered_off) {
+ arizona_disable_reset(arizona);
+ enable_irq(arizona->irq);
+ arizona->has_fully_powered_off = false;
+ }
+
regcache_cache_only(arizona->regmap, false);
switch (arizona->type) {
@@ -508,6 +529,14 @@ static int arizona_runtime_resume(struct device *dev)
goto err;
}
}
+
+ ret = wm5110_apply_sleep_patch(arizona);
+ if (ret) {
+ dev_err(arizona->dev,
+ "Failed to re-apply sleep patch: %d\n",
+ ret);
+ goto err;
+ }
break;
default:
ret = arizona_wait_for_boot(arizona);
@@ -545,10 +574,17 @@ err:
static int arizona_runtime_suspend(struct device *dev)
{
struct arizona *arizona = dev_get_drvdata(dev);
+ unsigned int val;
int ret;
dev_dbg(arizona->dev, "Entering AoD mode\n");
+ ret = regmap_read(arizona->regmap, ARIZONA_JACK_DETECT_ANALOGUE, &val);
+ if (ret) {
+ dev_err(dev, "Failed to check jack det status: %d\n", ret);
+ return ret;
+ }
+
if (arizona->external_dcvdd) {
ret = regmap_update_bits(arizona->regmap,
ARIZONA_ISOLATION_CONTROL,
@@ -559,33 +595,57 @@ static int arizona_runtime_suspend(struct device *dev)
ret);
return ret;
}
- } else {
- switch (arizona->type) {
- case WM5110:
- case WM8280:
- /*
- * As this is only called for the internal regulator
- * (where we know voltage ranges available) it is ok
- * to request an exact range.
- */
- ret = regulator_set_voltage(arizona->dcvdd,
- 1175000, 1175000);
- if (ret < 0) {
+ }
+
+ switch (arizona->type) {
+ case WM5110:
+ case WM8280:
+ if (arizona->external_dcvdd)
+ break;
+
+ /*
+ * As this is only called for the internal regulator
+ * (where we know voltage ranges available) it is ok
+ * to request an exact range.
+ */
+ ret = regulator_set_voltage(arizona->dcvdd, 1175000, 1175000);
+ if (ret < 0) {
+ dev_err(arizona->dev,
+ "Failed to set suspend voltage: %d\n", ret);
+ return ret;
+ }
+ break;
+ case WM5102:
+ if (!(val & ARIZONA_JD1_ENA))
+ ret = regmap_write(arizona->regmap,
+ ARIZONA_WRITE_SEQUENCER_CTRL_3, 0x0);
+ if (ret) {
dev_err(arizona->dev,
- "Failed to set suspend voltage: %d\n",
+ "Failed to clear write sequencer: %d\n",
ret);
return ret;
}
- break;
- default:
- break;
- }
+ break;
+ default:
+ break;
}
regcache_cache_only(arizona->regmap, true);
regcache_mark_dirty(arizona->regmap);
regulator_disable(arizona->dcvdd);
+ /* Allow us to completely power down if no jack detection */
+ if (!(val & ARIZONA_JD1_ENA)) {
+ dev_dbg(arizona->dev, "Fully powering off\n");
+
+ arizona->has_fully_powered_off = true;
+
+ disable_irq(arizona->irq);
+ arizona_enable_reset(arizona);
+ regulator_bulk_disable(arizona->num_core_supplies,
+ arizona->core_supplies);
+ }
+
return 0;
}
#endif
diff --git a/include/linux/mfd/arizona/core.h b/include/linux/mfd/arizona/core.h
index 16a498f..847bdaf 100644
--- a/include/linux/mfd/arizona/core.h
+++ b/include/linux/mfd/arizona/core.h
@@ -117,6 +117,7 @@ struct arizona {
int num_core_supplies;
struct regulator_bulk_data core_supplies[ARIZONA_MAX_CORE_SUPPLIES];
struct regulator *dcvdd;
+ bool has_fully_powered_off;
struct arizona_pdata pdata;
--
1.7.2.5
next prev parent reply other threads:[~2015-05-11 13:08 UTC|newest]
Thread overview: 23+ messages / expand[flat|nested] mbox.gz Atom feed top
2015-05-11 12:58 [RESEND PATCH v3 00/10] wm5110 Boot Fixups Charles Keepax
2015-05-11 12:58 ` [RESEND PATCH v3 01/10] mfd: arizona: Use devres to manage reset GPIO Charles Keepax
2015-05-13 12:20 ` Lee Jones
2015-05-11 12:58 ` [RESEND PATCH v3 02/10] mfd: arizona: Factor out hard reset into helper functions Charles Keepax
2015-05-13 12:20 ` Lee Jones
2015-05-11 12:58 ` [RESEND PATCH v3 03/10] mfd: wm5102: Ensure we always boot the device fully Charles Keepax
2015-05-13 12:20 ` Lee Jones
2015-05-11 12:58 ` [RESEND PATCH v3 04/10] mfd: arizona: Fix formating/style issues in arizona_apply_hardware_patch Charles Keepax
2015-05-13 12:21 ` Lee Jones
2015-05-11 12:58 ` [RESEND PATCH v3 05/10] mfd: arizona: Factor out SYSCLK enable from wm5102 hardware patch Charles Keepax
2015-05-13 12:21 ` Lee Jones
2015-05-11 12:58 ` [RESEND PATCH v3 06/10] mfd: wm5110: Add register patch required for low power sleep Charles Keepax
2015-05-13 12:21 ` Lee Jones
2015-05-11 12:58 ` [RESEND PATCH v3 07/10] regulator: arizona-ldo1: Add additional supported voltage Charles Keepax
2015-05-11 14:20 ` Mark Brown
2015-05-11 14:41 ` Charles Keepax
2015-05-11 16:04 ` Mark Brown
2015-05-11 12:58 ` [RESEND PATCH v3 08/10] mfd: wm5110: Set DCVDD voltage to 1.175V before entering sleep mode Charles Keepax
2015-05-13 12:21 ` Lee Jones
2015-05-11 12:58 ` Charles Keepax [this message]
2015-05-13 12:21 ` [RESEND PATCH v3 09/10] mfd: arizona: Add better support for system suspend Lee Jones
2015-05-11 12:58 ` [RESEND PATCH v3 10/10] mfd: wm5110: Add delay before releasing reset line Charles Keepax
2015-05-13 12:22 ` Lee Jones
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1431349090-24173-10-git-send-email-ckeepax@opensource.wolfsonmicro.com \
--to=ckeepax@opensource.wolfsonmicro.com \
--cc=broonie@kernel.org \
--cc=lee.jones@linaro.org \
--cc=lgirdwood@gmail.com \
--cc=linux-kernel@vger.kernel.org \
--cc=patches@opensource.wolfsonmicro.com \
--cc=sameo@linux.intel.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox