* [PATCH v10 2/2] drm/bridge: Add I2C based driver for ps8640 bridge
2016-02-19 8:31 [PATCH v10 1/2] Documentation: bridge: Add documentation for ps8640 DT properties Jitao Shi
@ 2016-02-19 8:31 ` Jitao Shi
2016-02-19 9:12 ` Philipp Zabel
2016-02-19 9:13 ` [PATCH v10 1/2] Documentation: bridge: Add documentation for ps8640 DT properties Philipp Zabel
1 sibling, 1 reply; 4+ messages in thread
From: Jitao Shi @ 2016-02-19 8:31 UTC (permalink / raw)
To: David Airlie, Matthias Brugger
Cc: Rob Herring, Pawel Moll, Mark Rutland, Ian Campbell, Kumar Gala,
Jitao Shi, Thierry Reding, Ajay Kumar, Inki Dae, Rahul Sharma,
Sean Paul, Vincent Palatin, Andy Yan, Philipp Zabel, Russell King,
devicetree, linux-kernel, dri-devel, linux-arm-kernel,
linux-mediatek, srv_heupstream, Sascha Hauer, yingjoe.chen,
eddie.huang, cawa.cheng, bibby.hsieh, ck.hu, stonea168
This patch adds drm_bridge driver for parade DSI to eDP bridge chip.
Signed-off-by: Jitao Shi <jitao.shi@mediatek.com>
---
Changes since v9:
- replace dev_kmalloc with devm_kmalloc in ps8640_get_modes
- remove ps_bridge->dsi = devm_kzalloc(dev, sizeof(struct mipi_dsi_device),
GFP_KERNEL);
- fix wrong condition in ps8640_validate_firmware()
The following patches are needed to support dsi host through none dsi bus:
https://patchwork.kernel.org/patch/8289181/ ("drm/dsi: check for CONFIG_OF when defining")
https://patchwork.kernel.org/patch/8289051/ ("drm/dsi: Use mipi_dsi_device_register_full for DSI device")
https://patchwork.kernel.org/patch/8289081/ ("drm/dsi: Try to match non-DT DSI devices")
https://patchwork.kernel.org/patch/8289121/ ("drm/dsi: Add routine to unregister a DSI device")
https://patchwork.kernel.org/patch/8289091/ ("drm/dsi: Get DSI host by DT device node")
---
drivers/gpu/drm/bridge/Kconfig | 11 +
drivers/gpu/drm/bridge/Makefile | 1 +
drivers/gpu/drm/bridge/parade-ps8640.c | 1057 ++++++++++++++++++++++++++++++++
3 files changed, 1069 insertions(+)
create mode 100644 drivers/gpu/drm/bridge/parade-ps8640.c
diff --git a/drivers/gpu/drm/bridge/Kconfig b/drivers/gpu/drm/bridge/Kconfig
index 27e2022..b4edd8c 100644
--- a/drivers/gpu/drm/bridge/Kconfig
+++ b/drivers/gpu/drm/bridge/Kconfig
@@ -40,4 +40,15 @@ config DRM_PARADE_PS8622
---help---
Parade eDP-LVDS bridge chip driver.
+config DRM_PARADE_PS8640
+ tristate "Parade PS8640 MIPI DSI to eDP Converter"
+ depends on OF && I2C
+ select DRM_KMS_HELPER
+ select DRM_MIPI_DSI
+ select DRM_PANEL
+ ---help---
+ Choose this option if you have PS8640 for display
+ The PS8640 is a high-performance and low-power
+ MIPI DSI to eDP converter
+
endmenu
diff --git a/drivers/gpu/drm/bridge/Makefile b/drivers/gpu/drm/bridge/Makefile
index f13c33d..fbe38dc 100644
--- a/drivers/gpu/drm/bridge/Makefile
+++ b/drivers/gpu/drm/bridge/Makefile
@@ -4,3 +4,4 @@ obj-$(CONFIG_DRM_DW_HDMI) += dw-hdmi.o
obj-$(CONFIG_DRM_DW_HDMI_AHB_AUDIO) += dw-hdmi-ahb-audio.o
obj-$(CONFIG_DRM_NXP_PTN3460) += nxp-ptn3460.o
obj-$(CONFIG_DRM_PARADE_PS8622) += parade-ps8622.o
+obj-$(CONFIG_DRM_PARADE_PS8640) += parade-ps8640.o
diff --git a/drivers/gpu/drm/bridge/parade-ps8640.c b/drivers/gpu/drm/bridge/parade-ps8640.c
new file mode 100644
index 0000000..5f27548
--- /dev/null
+++ b/drivers/gpu/drm/bridge/parade-ps8640.c
@@ -0,0 +1,1057 @@
+/*
+ * Copyright (c) 2014 MediaTek Inc.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ */
+
+#include <linux/delay.h>
+#include <linux/err.h>
+#include <linux/firmware.h>
+#include <linux/gpio.h>
+#include <linux/gpio/consumer.h>
+#include <linux/i2c.h>
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/of_gpio.h>
+#include <linux/of_graph.h>
+#include <linux/regulator/consumer.h>
+#include <asm/unaligned.h>
+#include <drm/drm_panel.h>
+
+#include <drmP.h>
+#include <drm_atomic_helper.h>
+#include <drm_crtc_helper.h>
+#include <drm_crtc.h>
+#include <drm_edid.h>
+#include <drm_mipi_dsi.h>
+
+#define PAGE2_SPI_CFG3 0x82
+#define I2C_TO_SPI_RESET 0x20
+#define PAGE2_ROMADD_BYTE1 0x8e
+#define PAGE2_ROMADD_BYTE2 0x8f
+#define PAGE2_SWSPI_WDATA 0x90
+#define PAGE2_SWSPI_RDATA 0x91
+#define PAGE2_SWSPI_LEN 0x92
+#define PAGE2_SWSPI_CTL 0x93
+#define TRIGGER_NO_READBACK 0x05
+#define TRIGGER_READBACK 0x01
+#define PAGE2_SPI_STATUS 0x9e
+#define PAGE2_GPIO_L 0xa6
+#define PAGE2_GPIO_H 0xa7
+#define PS_GPIO9 BIT(1)
+#define PAGE2_IROM_CTRL 0xb0
+#define IROM_ENABLE 0xc0
+#define IROM_DISABLE 0x80
+#define PAGE2_SW_REST 0xbc
+#define SPI_SW_RESET BIT(7)
+#define MPU_SW_RESET BIT(6)
+#define PAGE2_ENCTLSPI_WR 0xda
+#define PAGE2_I2C_BYPASS 0xea
+#define I2C_BYPASS_EN 0xd0
+#define PAGE3_SET_ADD 0xfe
+#define PAGE3_SET_VAL 0xff
+#define VDO_CTL_ADD 0x13
+#define VDO_DIS 0x18
+#define VDO_EN 0x1c
+#define PAGE4_REV_L 0xf0
+#define PAGE4_REV_H 0xf1
+#define PAGE4_CHIP_L 0xf2
+#define PAGE4_CHIP_H 0xf3
+
+/* Firmware */
+#define SPI_MAX_RETRY_CNT 8
+#define PS_FW_NAME "ps864x_fw.bin"
+
+#define FW_CHIP_ID_OFFSET 0
+#define FW_VERSION_OFFSET 2
+#define EDID_I2C_ADDR 0x50
+
+#define WRITE_STATUS_REG_CMD 0x01
+#define READ_STATUS_REG_CMD 0x05
+#define CLEAR_ALL_PROTECT 0x00
+#define BLK_PROTECT_BITS 0x0c
+#define STATUS_REG_PROTECT BIT(7)
+#define WRITE_ENABLE_CMD 0x06
+#define CHIP_ERASE_CMD 0xc7
+
+#define bridge_to_ps8640(e) container_of(e, struct ps8640, bridge)
+#define connector_to_ps8640(e) container_of(e, struct ps8640, connector)
+
+struct ps8640_info {
+ u8 family_id;
+ u8 variant_id;
+ u16 version;
+};
+
+struct ps8640 {
+ struct drm_connector connector;
+ struct drm_bridge bridge;
+ struct edid *edid;
+ struct mipi_dsi_device dsi;
+ struct i2c_client *page[8];
+ struct i2c_client *ddc_i2c;
+ struct regulator_bulk_data supplies[2];
+ struct drm_panel *panel;
+ struct gpio_desc *gpio_rst_n;
+ struct gpio_desc *gpio_slp_n;
+ struct gpio_desc *gpio_mode_sel_n;
+ bool enabled;
+
+ /* firmware file info */
+ bool in_fw_update;
+ struct ps8640_info info;
+};
+
+static const u8 enc_ctrl_code[6] = {0xaa, 0x55, 0x50, 0x41, 0x52, 0x44};
+
+static int ps8640_read(struct i2c_client *client, u8 reg, u8 *data,
+ u16 data_len)
+{
+ int ret;
+ struct i2c_msg msgs[] = {
+ {
+ .addr = client->addr,
+ .flags = 0,
+ .len = 1,
+ .buf = ®,
+ },
+ {
+ .addr = client->addr,
+ .flags = I2C_M_RD,
+ .len = data_len,
+ .buf = data,
+ }
+ };
+
+ ret = i2c_transfer(client->adapter, msgs, 2);
+
+ if (ret == 2)
+ return 0;
+ if (ret < 0)
+ return ret;
+ else
+ return -EIO;
+}
+
+static int ps8640_write_bytes(struct i2c_client *client, u8 *data,
+ u16 data_len)
+{
+ int ret;
+ struct i2c_msg msg;
+
+ msg.addr = client->addr;
+ msg.flags = 0;
+ msg.len = data_len;
+ msg.buf = data;
+
+ ret = i2c_transfer(client->adapter, &msg, 1);
+ if (ret == 1)
+ return 0;
+ if (ret < 0)
+ return ret;
+ else
+ return -EIO;
+}
+
+static int ps8640_write_byte(struct i2c_client *client, u8 reg, u8 data)
+{
+ int ret;
+ struct i2c_msg msg;
+ u8 buf[] = {reg, data};
+
+ msg.addr = client->addr;
+ msg.flags = 0;
+ msg.len = sizeof(buf);
+ msg.buf = buf;
+
+ ret = i2c_transfer(client->adapter, &msg, 1);
+ if (ret == 1)
+ return 0;
+ if (ret < 0)
+ return ret;
+ else
+ return -EIO;
+}
+
+static void ps8640_get_mcu_fw_version(struct ps8640 *ps_bridge)
+{
+ struct i2c_client *client = ps_bridge->page[5];
+ u8 fw_ver[2];
+
+ ps8640_read(client, 0x4, fw_ver, 2);
+ ps_bridge->info.version = (fw_ver[0] << 8) | fw_ver[1];
+
+ DRM_INFO_ONCE("ps8640 rom fw version %d.%d\n", fw_ver[0], fw_ver[1]);
+}
+
+static int ps8640_bridge_enable(struct ps8640 *ps_bridge)
+{
+ struct i2c_client *client = ps_bridge->page[3];
+ u8 vdo_ctrl_buf[3] = {PAGE3_SET_ADD, VDO_CTL_ADD, VDO_EN};
+
+ return ps8640_write_bytes(client, vdo_ctrl_buf, 3);
+}
+
+static int ps8640_bridge_disable(struct ps8640 *ps_bridge)
+{
+ struct i2c_client *client = ps_bridge->page[3];
+ u8 vdo_ctrl_buf[3] = {PAGE3_SET_ADD, VDO_CTL_ADD, VDO_DIS};
+
+ return ps8640_write_bytes(client, vdo_ctrl_buf, 3);
+}
+
+static void ps8640_pre_enable(struct drm_bridge *bridge)
+{
+ struct ps8640 *ps_bridge = bridge_to_ps8640(bridge);
+ struct i2c_client *client = ps_bridge->page[2];
+ int err, retry_cnt = 0;
+ u8 set_vdo_done;
+
+ if (ps_bridge->in_fw_update)
+ return;
+
+ if (ps_bridge->enabled)
+ return;
+
+ err = drm_panel_prepare(ps_bridge->panel);
+ if (err < 0) {
+ DRM_ERROR("failed to prepare panel: %d\n", err);
+ return;
+ }
+
+ gpiod_set_value(ps_bridge->gpio_slp_n, 1);
+ gpiod_set_value(ps_bridge->gpio_rst_n, 0);
+
+ err = regulator_bulk_enable(ARRAY_SIZE(ps_bridge->supplies),
+ ps_bridge->supplies);
+ if (err < 0) {
+ DRM_ERROR("cannot enable regulators %d\n", err);
+ goto err_panel_unprepare;
+ }
+
+ usleep_range(500, 700);
+ gpiod_set_value(ps_bridge->gpio_rst_n, 1);
+
+ /*
+ * Wait for the ps8640 embed mcu ready
+ * First wait 200ms and then check the mcu ready flag every 20ms
+ */
+ msleep(200);
+ do {
+ err = ps8640_read(client, PAGE2_GPIO_H, &set_vdo_done, 1);
+ if (err < 0) {
+ DRM_ERROR("failed read PAGE2_GPIO_H: %d\n", err);
+ goto err_regulators_disable;
+ }
+ msleep(20);
+ } while ((retry_cnt++ < 10) && ((set_vdo_done & PS_GPIO9) != PS_GPIO9));
+
+ if (ps_bridge->info.version == 0)
+ ps8640_get_mcu_fw_version(ps_bridge);
+ /* Switch access edp panel's edid through i2c */
+ ps8640_write_byte(client, PAGE2_I2C_BYPASS, I2C_BYPASS_EN);
+ ps_bridge->enabled = true;
+
+ return;
+
+err_regulators_disable:
+ regulator_bulk_disable(ARRAY_SIZE(ps_bridge->supplies),
+ ps_bridge->supplies);
+err_panel_unprepare:
+ drm_panel_unprepare(ps_bridge->panel);
+}
+
+static void ps8640_enable(struct drm_bridge *bridge)
+{
+ struct ps8640 *ps_bridge = bridge_to_ps8640(bridge);
+ int err;
+
+ err = ps8640_bridge_enable(ps_bridge);
+ if (err)
+ DRM_ERROR("failed to enable unmutevideo: %d\n", err);
+
+ err = drm_panel_enable(ps_bridge->panel);
+ if (err < 0)
+ DRM_ERROR("failed to enable panel: %d\n", err);
+}
+
+static void ps8640_disable(struct drm_bridge *bridge)
+{
+ struct ps8640 *ps_bridge = bridge_to_ps8640(bridge);
+ int err;
+
+ err = drm_panel_disable(ps_bridge->panel);
+ if (err < 0)
+ DRM_ERROR("failed to disable panel: %d\n", err);
+
+ err = ps8640_bridge_disable(ps_bridge);
+ if (err < 0)
+ DRM_ERROR("failed to disable bridge: %d\n", err);
+}
+
+static void ps8640_post_disable(struct drm_bridge *bridge)
+{
+ struct ps8640 *ps_bridge = bridge_to_ps8640(bridge);
+ int err;
+
+ if (ps_bridge->in_fw_update)
+ return;
+
+ if (!ps_bridge->enabled)
+ return;
+
+ ps_bridge->enabled = false;
+
+ gpiod_set_value(ps_bridge->gpio_rst_n, 0);
+ gpiod_set_value(ps_bridge->gpio_slp_n, 0);
+ err = regulator_bulk_disable(ARRAY_SIZE(ps_bridge->supplies),
+ ps_bridge->supplies);
+ if (err < 0)
+ DRM_ERROR("cannot disable regulators %d\n", err);
+
+ err = drm_panel_unprepare(ps_bridge->panel);
+ if (err)
+ DRM_ERROR("failed to unprepare panel: %d\n", err);
+}
+
+static int ps8640_get_modes(struct drm_connector *connector)
+{
+ struct ps8640 *ps_bridge = connector_to_ps8640(connector);
+ struct device *dev = &ps_bridge->page[0]->dev;
+ u8 *edid;
+ int ret, num_modes = 0;
+ bool power_off;
+
+ if (ps_bridge->edid)
+ return drm_add_edid_modes(connector, ps_bridge->edid);
+
+ power_off = !ps_bridge->enabled;
+ ps8640_pre_enable(&ps_bridge->bridge);
+
+ edid = devm_kmalloc(dev, EDID_LENGTH, GFP_KERNEL);
+ if (!edid) {
+ DRM_ERROR("Failed to allocate EDID\n");
+ return 0;
+ }
+
+ ret = ps8640_read(ps_bridge->ddc_i2c, 0, edid, EDID_LENGTH);
+ if (ret)
+ goto out;
+
+ ps_bridge->edid = (struct edid *)edid;
+ drm_mode_connector_update_edid_property(connector, ps_bridge->edid);
+
+ num_modes = drm_add_edid_modes(connector, ps_bridge->edid);
+
+out:
+ if (power_off)
+ ps8640_post_disable(&ps_bridge->bridge);
+
+ return num_modes;
+}
+
+static struct drm_encoder *ps8640_best_encoder(struct drm_connector *connector)
+{
+ struct ps8640 *ps_bridge;
+
+ ps_bridge = connector_to_ps8640(connector);
+ return ps_bridge->bridge.encoder;
+}
+
+static const struct drm_connector_helper_funcs ps8640_connector_helper_funcs = {
+ .get_modes = ps8640_get_modes,
+ .best_encoder = ps8640_best_encoder,
+};
+
+static enum drm_connector_status ps8640_detect(struct drm_connector *connector,
+ bool force)
+{
+ return connector_status_connected;
+}
+
+static void ps8640_connector_destroy(struct drm_connector *connector)
+{
+ drm_connector_unregister(connector);
+ drm_connector_cleanup(connector);
+}
+
+static const struct drm_connector_funcs ps8640_connector_funcs = {
+ .dpms = drm_atomic_helper_connector_dpms,
+ .fill_modes = drm_helper_probe_single_connector_modes,
+ .detect = ps8640_detect,
+ .destroy = ps8640_connector_destroy,
+ .reset = drm_atomic_helper_connector_reset,
+ .atomic_duplicate_state = drm_atomic_helper_connector_duplicate_state,
+ .atomic_destroy_state = drm_atomic_helper_connector_destroy_state,
+};
+
+int ps8640_bridge_attach(struct drm_bridge *bridge)
+{
+ struct ps8640 *ps_bridge = bridge_to_ps8640(bridge);
+ struct device *dev = &ps_bridge->page[0]->dev;
+ struct device_node *np = dev->of_node;
+ struct device_node *port, *in_ep;
+ struct device_node *dsi_node = NULL;
+ struct mipi_dsi_host *host = ps_bridge->dsi.host;
+ int ret;
+
+ ret = drm_connector_init(bridge->dev, &ps_bridge->connector,
+ &ps8640_connector_funcs,
+ DRM_MODE_CONNECTOR_eDP);
+
+ if (ret) {
+ DRM_ERROR("Failed to initialize connector with drm: %d\n", ret);
+ return ret;
+ }
+
+ drm_connector_helper_add(&ps_bridge->connector,
+ &ps8640_connector_helper_funcs);
+ drm_connector_register(&ps_bridge->connector);
+
+ ps_bridge->connector.dpms = DRM_MODE_DPMS_ON;
+ drm_mode_connector_attach_encoder(&ps_bridge->connector,
+ bridge->encoder);
+
+ if (ps_bridge->panel)
+ drm_panel_attach(ps_bridge->panel, &ps_bridge->connector);
+
+ /* port@0 is ps8640 dsi input port */
+ port = of_graph_get_port_by_id(np, 0);
+ if (port) {
+ in_ep = of_get_child_by_name(port, "endpoint");
+ of_node_put(port);
+ if (in_ep) {
+ dsi_node = of_graph_get_remote_port_parent(in_ep);
+ of_node_put(in_ep);
+ }
+ }
+ if (dsi_node) {
+ host = of_find_mipi_dsi_host_by_node(dsi_node);
+ of_node_put(dsi_node);
+ if (!host)
+ return -ENODEV;
+ }
+
+ ps_bridge->dsi.host = host;
+ ps_bridge->dsi.mode_flags = MIPI_DSI_MODE_VIDEO |
+ MIPI_DSI_MODE_VIDEO_SYNC_PULSE;
+ ps_bridge->dsi.format = MIPI_DSI_FMT_RGB888;
+ ps_bridge->dsi.lanes = 4;
+ ret = mipi_dsi_attach(&ps_bridge->dsi);
+ if (ret) {
+ drm_panel_detach(ps_bridge->panel);
+ return ret;
+ }
+
+ return ret;
+}
+
+static const struct drm_bridge_funcs ps8640_bridge_funcs = {
+ .attach = ps8640_bridge_attach,
+ .disable = ps8640_disable,
+ .post_disable = ps8640_post_disable,
+ .pre_enable = ps8640_pre_enable,
+ .enable = ps8640_enable,
+};
+
+/* Firmware Version is returned as Major.Minor.Build */
+static ssize_t ps8640_fw_version_show(struct device *dev,
+ struct device_attribute *attr, char *buf)
+{
+ struct ps8640 *ps_bridge = dev_get_drvdata(dev);
+ struct ps8640_info *info = &ps_bridge->info;
+
+ return scnprintf(buf, PAGE_SIZE, "%u.%u\n", info->version >> 8,
+ info->version & 0xff);
+}
+
+/* Hardware Version is returned as FamilyID.VariantID */
+static ssize_t ps8640_hw_version_show(struct device *dev,
+ struct device_attribute *attr, char *buf)
+{
+ struct ps8640 *ps_bridge = dev_get_drvdata(dev);
+ struct ps8640_info *info = &ps_bridge->info;
+
+ return scnprintf(buf, PAGE_SIZE, "ps%u.%u\n", info->family_id,
+ info->variant_id);
+}
+
+static int ps8640_spi_send_cmd(struct ps8640 *ps_bridge, u8 *cmd, u8 cmd_len)
+{
+ struct i2c_client *client = ps_bridge->page[2];
+ u8 i, buf[3];
+ int ret;
+
+ ret = ps8640_write_byte(client, PAGE2_IROM_CTRL, IROM_ENABLE);
+ if (ret)
+ goto err;
+
+ /* write command in write port */
+ for (i = 0; i < cmd_len; i++) {
+ ret = ps8640_write_byte(client, PAGE2_SWSPI_WDATA, cmd[i]);
+ if (ret)
+ goto err;
+ }
+
+ buf[0] = PAGE2_SWSPI_LEN;
+ buf[1] = cmd_len - 1;
+ buf[2] = TRIGGER_NO_READBACK;
+ ret = ps8640_write_bytes(client, buf, 3);
+ if (ret)
+ goto err;
+
+ ret = ps8640_write_byte(client, PAGE2_IROM_CTRL, IROM_DISABLE);
+ if (ret)
+ goto err;
+
+ return 0;
+
+err:
+ dev_err(&client->dev, "send command err: %d\n", ret);
+ return ret;
+}
+
+static int ps8640_wait_spi_ready(struct ps8640 *ps_bridge)
+{
+ struct i2c_client *client = ps_bridge->page[2];
+ u8 spi_rdy_st, retry_cnt = 0;
+
+ do {
+ ps8640_read(client, PAGE2_SPI_STATUS, &spi_rdy_st, 1);
+ msleep(20);
+ if ((retry_cnt == SPI_MAX_RETRY_CNT) &&
+ ((spi_rdy_st & 0x0c) != 0x0c)) {
+ dev_err(&client->dev, "wait spi ready timeout\n");
+ return -EBUSY;
+ }
+ } while ((retry_cnt++ < SPI_MAX_RETRY_CNT) &&
+ (spi_rdy_st & 0x0c) == 0x0c);
+
+ return 0;
+}
+
+static int ps8640_wait_spi_nobusy(struct ps8640 *ps_bridge)
+{
+ struct i2c_client *client = ps_bridge->page[2];
+ u8 spi_status, buf[3], retry_cnt = 0;
+ int ret;
+
+ do {
+ /* 0x05 RDSR; Read-Status-Register */
+ ret = ps8640_write_byte(client, PAGE2_SWSPI_WDATA,
+ READ_STATUS_REG_CMD);
+ if (ret)
+ goto err_send_cmd_exit;
+
+ buf[0] = PAGE2_SWSPI_LEN;
+ buf[1] = 0;
+ buf[2] = TRIGGER_READBACK;
+ ret = ps8640_write_bytes(client, buf, 3);
+ if (ret)
+ goto err_send_cmd_exit;
+
+ /* delay for cmd send */
+ usleep_range(100, 300);
+ /* wait for SPI ROM until not busy */
+ ret = ps8640_read(client, PAGE2_SWSPI_RDATA, &spi_status, 1);
+ if (ret)
+ goto err_send_cmd_exit;
+ } while ((retry_cnt++ < SPI_MAX_RETRY_CNT) &&
+ (spi_status & BLK_PROTECT_BITS) == BLK_PROTECT_BITS);
+
+ if ((retry_cnt > SPI_MAX_RETRY_CNT) &&
+ (spi_status & BLK_PROTECT_BITS) != BLK_PROTECT_BITS) {
+ ret = -EBUSY;
+ dev_err(&client->dev, "wait spi no busy timeout: %d\n", ret);
+ goto err_timeout;
+ }
+
+ return 0;
+
+err_send_cmd_exit:
+ dev_err(&client->dev, "send command err: %d\n", ret);
+
+err_timeout:
+ return ret;
+}
+
+static int ps8640_wait_rom_idle(struct ps8640 *ps_bridge)
+{
+ struct i2c_client *client = ps_bridge->page[0];
+ int ret;
+
+ ret = ps8640_write_byte(client, PAGE2_IROM_CTRL, IROM_ENABLE);
+ if (ret)
+ goto exit;
+
+ ret = ps8640_wait_spi_ready(ps_bridge);
+ if (ret)
+ goto exit;
+
+ ret = ps8640_wait_spi_nobusy(ps_bridge);
+ if (ret)
+ goto exit;
+
+ ret = ps8640_write_byte(client, PAGE2_IROM_CTRL, IROM_DISABLE);
+ if (ret)
+ goto exit;
+
+exit:
+ if (ret)
+ dev_err(&client->dev, "wait ps8640 rom idle fail: %d\n", ret);
+
+ return ret;
+}
+
+static int ps8640_spi_dl_mode(struct ps8640 *ps_bridge)
+{
+ struct i2c_client *client = ps_bridge->page[2];
+ int ret;
+
+ /* switch ps8640 mode to spi dl mode */
+ gpiod_set_value(ps_bridge->gpio_mode_sel_n, 0);
+
+ /* reset spi interface */
+ ret = ps8640_write_byte(client, PAGE2_SW_REST,
+ SPI_SW_RESET | MPU_SW_RESET);
+ if (ret)
+ goto exit;
+
+ ret = ps8640_write_byte(client, PAGE2_SW_REST, MPU_SW_RESET);
+ if (ret)
+ goto exit;
+
+exit:
+ if (ret)
+ dev_err(&client->dev, "fail reset spi interface: %d\n", ret);
+
+ return ret;
+}
+
+static int ps8640_rom_prepare(struct ps8640 *ps_bridge)
+{
+ struct i2c_client *client = ps_bridge->page[2];
+ struct device *dev = &client->dev;
+ u8 i, cmd[2];
+ int ret;
+
+ cmd[0] = WRITE_ENABLE_CMD;
+ ret = ps8640_spi_send_cmd(ps_bridge, cmd, 1);
+ if (ret) {
+ dev_err(dev, "failed enable-write-status-register: %d\n", ret);
+ return ret;
+ }
+
+ cmd[0] = WRITE_STATUS_REG_CMD;
+ cmd[1] = CLEAR_ALL_PROTECT;
+ ret = ps8640_spi_send_cmd(ps_bridge, cmd, 2);
+ if (ret) {
+ dev_err(dev, "fail disable all protection: %d\n", ret);
+ return ret;
+ }
+
+ /* wait for SPI module ready */
+ ret = ps8640_wait_rom_idle(ps_bridge);
+ if (ret) {
+ dev_err(dev, "fail wait rom idle: %d\n", ret);
+ return ret;
+ }
+
+ ps8640_write_byte(client, PAGE2_IROM_CTRL, IROM_ENABLE);
+ for (i = 0; i < 6; i++)
+ ps8640_write_byte(client, PAGE2_ENCTLSPI_WR, enc_ctrl_code[i]);
+ ps8640_write_byte(client, PAGE2_IROM_CTRL, IROM_DISABLE);
+
+ /* Enable-Write-Status-Register */
+ cmd[0] = WRITE_ENABLE_CMD;
+ ret = ps8640_spi_send_cmd(ps_bridge, cmd, 1);
+ if (ret) {
+ dev_err(dev, "fail enable-write-status-register: %d\n", ret);
+ return ret;
+ }
+
+ /* chip erase command */
+ cmd[0] = CHIP_ERASE_CMD;
+ ret = ps8640_spi_send_cmd(ps_bridge, cmd, 1);
+ if (ret) {
+ dev_err(dev, "fail disable all protection: %d\n", ret);
+ return ret;
+ }
+
+ ret = ps8640_wait_rom_idle(ps_bridge);
+ if (ret) {
+ dev_err(dev, "fail wait rom idle: %d\n", ret);
+ return ret;
+ }
+
+ return 0;
+}
+
+static int ps8640_validate_firmware(struct ps8640 *ps_bridge,
+ const struct firmware *fw)
+{
+ struct i2c_client *client = ps_bridge->page[0];
+ struct ps8640_info *info = &ps_bridge->info;
+ u16 fw_chip_id, fw_version_id;
+
+ /*
+ * Get the chip_id from the firmware. Make sure that it is the
+ * right controller to do the firmware and config update.
+ */
+ fw_chip_id = get_unaligned_le16(fw->data + FW_CHIP_ID_OFFSET);
+
+ if (fw_chip_id != 0x8640) {
+ dev_err(&client->dev,
+ "chip id mismatch: fw 0x%x vs. chip 0x8640\n",
+ fw_chip_id);
+ return -ENODEV;
+ }
+
+ fw_version_id = get_unaligned_le16(fw->data + FW_VERSION_OFFSET);
+
+ if (fw_version_id == info->version) {
+ dev_err(&client->dev,
+ "no need update fw version same: fw %d.%d vs. chip %d.%d\n",
+ fw_version_id >> 8, fw_version_id & 0xff,
+ info->version >> 8, info->version & 0xff);
+ return -ENODEV;
+ }
+
+ return 0;
+}
+
+static int ps8640_write_rom(struct ps8640 *ps_bridge, const struct firmware *fw)
+{
+ struct i2c_client *client = ps_bridge->page[0];
+ struct device *dev = &client->dev;
+ struct i2c_client *client2 = ps_bridge->page[2];
+ struct i2c_client *client7 = ps_bridge->page[7];
+ unsigned int pos = 0;
+ u8 buf[257], rom_page_id_buf[3];
+ int ret;
+ u16 cpy_len;
+
+ ps8640_write_byte(client2, PAGE2_SPI_CFG3, I2C_TO_SPI_RESET);
+ msleep(100);
+ ps8640_write_byte(client2, PAGE2_SPI_CFG3, 0x00);
+
+ while (pos < fw->size) {
+ rom_page_id_buf[0] = PAGE2_ROMADD_BYTE1;
+ rom_page_id_buf[1] = (pos >> 8) & 0xff;
+ rom_page_id_buf[2] = (pos >> 16) & 0xff;
+ ret = ps8640_write_bytes(client2, rom_page_id_buf, 3);
+ if (ret)
+ goto error;
+ cpy_len = fw->size >= 256 + pos ? 256 : fw->size - pos;
+ buf[0] = 0;
+ memcpy(buf + 1, fw->data + pos, cpy_len);
+ ret = ps8640_write_bytes(client7, buf, cpy_len + 1);
+ if (ret)
+ goto error;
+
+ pos += cpy_len;
+
+ dev_dbg(dev, "fw update completed %u / %zu bytes\n", pos,
+ fw->size);
+ }
+ return 0;
+
+error:
+ dev_err(dev, "failed write extenal flash, %d\n", ret);
+ return ret;
+}
+
+static int ps8640_spi_normal_mode(struct ps8640 *ps_bridge)
+{
+ u8 cmd[2];
+ struct i2c_client *client = ps_bridge->page[2];
+
+ /* Enable-Write-Status-Register */
+ cmd[0] = WRITE_ENABLE_CMD;
+ ps8640_spi_send_cmd(ps_bridge, cmd, 1);
+
+ /* protect BPL/BP0/BP1 */
+ cmd[0] = WRITE_STATUS_REG_CMD;
+ cmd[1] = BLK_PROTECT_BITS | STATUS_REG_PROTECT;
+ ps8640_spi_send_cmd(ps_bridge, cmd, 2);
+
+ /* wait for SPI rom ready */
+ ps8640_wait_rom_idle(ps_bridge);
+
+ /* disable PS8640 mapping function */
+ ps8640_write_byte(client, PAGE2_ENCTLSPI_WR, 0x00);
+
+ gpiod_set_value(ps_bridge->gpio_mode_sel_n, 1);
+ return 0;
+}
+
+static int ps8640_enter_bl(struct ps8640 *ps_bridge)
+{
+ ps_bridge->in_fw_update = true;
+ return ps8640_spi_dl_mode(ps_bridge);
+}
+
+static void ps8640_exit_bl(struct ps8640 *ps_bridge, const struct firmware *fw)
+{
+ ps8640_spi_normal_mode(ps_bridge);
+ ps_bridge->in_fw_update = false;
+}
+
+static int ps8640_load_fw(struct ps8640 *ps_bridge, const struct firmware *fw)
+{
+ struct i2c_client *client = ps_bridge->page[0];
+ struct device *dev = &client->dev;
+ int ret;
+ bool ps8640_status_backup = ps_bridge->enabled;
+
+ if (!ps_bridge->in_fw_update) {
+ if (!ps8640_status_backup)
+ ps8640_pre_enable(&ps_bridge->bridge);
+
+ ret = ps8640_enter_bl(ps_bridge);
+ if (ret)
+ goto exit;
+ }
+
+ ret = ps8640_validate_firmware(ps_bridge, fw);
+ if (ret)
+ goto exit;
+
+ ret = ps8640_rom_prepare(ps_bridge);
+ if (ret)
+ goto exit;
+
+ ret = ps8640_write_rom(ps_bridge, fw);
+
+exit:
+ if (ret)
+ dev_err(dev, "Failed to load firmware, %d\n", ret);
+
+ ps8640_exit_bl(ps_bridge, fw);
+ if (!ps8640_status_backup)
+ ps8640_post_disable(&ps_bridge->bridge);
+ return ret;
+}
+
+static ssize_t ps8640_update_fw_store(struct device *dev,
+ struct device_attribute *attr,
+ const char *buf, size_t count)
+{
+ struct i2c_client *client = to_i2c_client(dev);
+ struct ps8640 *ps_bridge = i2c_get_clientdata(client);
+ const struct firmware *fw;
+ int error;
+
+ error = request_firmware(&fw, PS_FW_NAME, dev);
+ if (error) {
+ dev_err(dev, "Unable to open firmware %s: %d\n",
+ PS_FW_NAME, error);
+ return error;
+ }
+
+ error = ps8640_load_fw(ps_bridge, fw);
+ if (error)
+ dev_err(dev, "The firmware update failed(%d)\n", error);
+ else
+ dev_info(dev, "The firmware update succeeded\n");
+
+ release_firmware(fw);
+ return error ? error : count;
+}
+
+static DEVICE_ATTR(fw_version, S_IRUGO, ps8640_fw_version_show, NULL);
+static DEVICE_ATTR(hw_version, S_IRUGO, ps8640_hw_version_show, NULL);
+static DEVICE_ATTR(update_fw, S_IWUSR, NULL, ps8640_update_fw_store);
+
+static struct attribute *ps8640_attrs[] = {
+ &dev_attr_fw_version.attr,
+ &dev_attr_hw_version.attr,
+ &dev_attr_update_fw.attr,
+ NULL
+};
+
+static const struct attribute_group ps8640_attr_group = {
+ .attrs = ps8640_attrs,
+};
+
+static void ps8640_remove_sysfs_group(void *data)
+{
+ struct ps8640 *ps_bridge = data;
+
+ sysfs_remove_group(&ps_bridge->page[0]->dev.kobj, &ps8640_attr_group);
+}
+
+static int ps8640_probe(struct i2c_client *client,
+ const struct i2c_device_id *id)
+{
+ struct device *dev = &client->dev;
+ struct ps8640 *ps_bridge;
+ struct device_node *np = dev->of_node;
+ struct device_node *port, *out_ep;
+ struct device_node *panel_node = NULL;
+ int i, ret;
+
+ ps_bridge = devm_kzalloc(dev, sizeof(*ps_bridge), GFP_KERNEL);
+ if (!ps_bridge)
+ return -ENOMEM;
+
+ /* port@1 is ps8640 output port */
+ port = of_graph_get_port_by_id(np, 1);
+ if (port) {
+ out_ep = of_get_child_by_name(port, "endpoint");
+ of_node_put(port);
+ if (out_ep) {
+ panel_node = of_graph_get_remote_port_parent(out_ep);
+ of_node_put(out_ep);
+ }
+ }
+ if (panel_node) {
+ ps_bridge->panel = of_drm_find_panel(panel_node);
+ of_node_put(panel_node);
+ if (!ps_bridge->panel)
+ return -EPROBE_DEFER;
+ }
+
+ ps_bridge->supplies[0].supply = "vdd33";
+ ps_bridge->supplies[1].supply = "vdd12";
+ ret = devm_regulator_bulk_get(dev, ARRAY_SIZE(ps_bridge->supplies),
+ ps_bridge->supplies);
+ if (ret) {
+ dev_info(dev, "failed to get regulators: %d\n", ret);
+ return -EPROBE_DEFER;
+ }
+
+ ps_bridge->gpio_mode_sel_n = devm_gpiod_get(&client->dev, "mode-sel",
+ GPIOD_OUT_HIGH);
+ if (IS_ERR(ps_bridge->gpio_mode_sel_n)) {
+ ret = PTR_ERR(ps_bridge->gpio_mode_sel_n);
+ dev_err(dev, "cannot get mode-sel %d\n", ret);
+ return ret;
+ }
+
+ ps_bridge->gpio_slp_n = devm_gpiod_get(&client->dev, "sleep",
+ GPIOD_OUT_HIGH);
+ if (IS_ERR(ps_bridge->gpio_slp_n)) {
+ ret = PTR_ERR(ps_bridge->gpio_slp_n);
+ dev_err(dev, "cannot get sleep: %d\n", ret);
+ return ret;
+ }
+
+ ps_bridge->gpio_rst_n = devm_gpiod_get(&client->dev, "reset",
+ GPIOD_OUT_HIGH);
+ if (IS_ERR(ps_bridge->gpio_rst_n)) {
+ ret = PTR_ERR(ps_bridge->gpio_rst_n);
+ dev_err(dev, "cannot get reset: %d\n", ret);
+ return ret;
+ }
+
+ ps_bridge->bridge.funcs = &ps8640_bridge_funcs;
+ ps_bridge->bridge.of_node = dev->of_node;
+ ret = drm_bridge_add(&ps_bridge->bridge);
+ if (ret) {
+ dev_err(dev, "Failed to add bridge: %d\n", ret);
+ return ret;
+ }
+
+ ps_bridge->page[0] = client;
+ ps_bridge->ddc_i2c = i2c_new_dummy(client->adapter, EDID_I2C_ADDR);
+ if (!ps_bridge->ddc_i2c) {
+ dev_err(dev, "failed ddc_i2c dummy device, address%02x\n",
+ EDID_I2C_ADDR);
+ ret = -EBUSY;
+ goto exit_ddc_i2c_dummy;
+ }
+ /*
+ * ps8640 uses multiple addresses, use dummy devices for them
+ * page[0]: for DP control
+ * page[1]: for VIDEO Bridge
+ * page[2]: for control top
+ * page[3]: for DSI Link Control1
+ * page[4]: for MIPI Phy
+ * page[5]: for VPLL
+ * page[6]: for DSI Link Control2
+ * page[7]: for spi rom mapping
+ */
+ for (i = 1; i < 8; i++) {
+ ps_bridge->page[i] = i2c_new_dummy(client->adapter,
+ client->addr + i);
+ if (!ps_bridge->page[i]) {
+ dev_err(dev, "failed i2c dummy device, address%02x\n",
+ client->addr + i);
+ ret = -EBUSY;
+ goto exit_dummy;
+ }
+ }
+ i2c_set_clientdata(client, ps_bridge);
+
+ ret = sysfs_create_group(&client->dev.kobj, &ps8640_attr_group);
+ if (ret) {
+ dev_err(dev, "failed to create sysfs entries: %d\n", ret);
+ goto exit_dummy;
+ }
+
+ ret = devm_add_action(dev, ps8640_remove_sysfs_group, ps_bridge);
+ if (ret) {
+ dev_err(dev, "failed to add sysfs cleanup action: %d\n", ret);
+ goto exit_remove_sysfs;
+ }
+ return 0;
+
+exit_remove_sysfs:
+ sysfs_remove_group(&ps_bridge->page[0]->dev.kobj, &ps8640_attr_group);
+exit_dummy:
+ for (i = 1; i < 8; i++)
+ if (ps_bridge->page[i])
+ i2c_unregister_device(ps_bridge->page[i]);
+exit_ddc_i2c_dummy:
+ drm_bridge_remove(&ps_bridge->bridge);
+ return ret;
+}
+
+static int ps8640_remove(struct i2c_client *client)
+{
+ struct ps8640 *ps_bridge = i2c_get_clientdata(client);
+ int i;
+
+ for (i = 1; i < 8; i++)
+ i2c_unregister_device(ps_bridge->page[i]);
+
+ drm_bridge_remove(&ps_bridge->bridge);
+
+ return 0;
+}
+
+static const struct i2c_device_id ps8640_i2c_table[] = {
+ {"parade,ps8640", 0},
+ {},
+};
+MODULE_DEVICE_TABLE(i2c, ps8640_i2c_table);
+
+static const struct of_device_id ps8640_match[] = {
+ { .compatible = "parade,ps8640" },
+ {},
+};
+MODULE_DEVICE_TABLE(of, ps8640_match);
+
+static struct i2c_driver ps8640_driver = {
+ .id_table = ps8640_i2c_table,
+ .probe = ps8640_probe,
+ .remove = ps8640_remove,
+ .driver = {
+ .name = "parade,ps8640",
+ .of_match_table = ps8640_match,
+ },
+};
+module_i2c_driver(ps8640_driver);
+
+MODULE_AUTHOR("Jitao Shi <jitao.shi@mediatek.com>");
+MODULE_AUTHOR("CK Hu <ck.hu@mediatek.com>");
+MODULE_DESCRIPTION("PARADE ps8640 DSI-eDP converter driver");
+MODULE_LICENSE("GPL v2");
--
1.7.9.5
^ permalink raw reply related [flat|nested] 4+ messages in thread