From: Roger Quadros <rogerq@ti.com>
To: <tony@atomide.com>, <computersforpeace@gmail.com>
Cc: <dwmw2@infradead.org>, <ezequiel@vanguardiasur.com.ar>,
<javier@dowhile0.org>, <fcooper@ti.com>, <nsekhar@ti.com>,
<linux-mtd@lists.infradead.org>, <linux-omap@vger.kernel.org>,
<devicetree@vger.kernel.org>, <linux-kernel@vger.kernel.org>,
Roger Quadros <rogerq@ti.com>
Subject: [PATCH v5 17/26] mtd: nand: omap2: Implement NAND ready using gpiolib
Date: Fri, 19 Feb 2016 23:15:39 +0200 [thread overview]
Message-ID: <1455916548-3441-18-git-send-email-rogerq@ti.com> (raw)
In-Reply-To: <1455916548-3441-1-git-send-email-rogerq@ti.com>
The GPMC WAIT pin status are now available over gpiolib.
Update the omap_dev_ready() function to use gpio instead of
directly accessing GPMC register space.
Signed-off-by: Roger Quadros <rogerq@ti.com>
---
.../devicetree/bindings/mtd/gpmc-nand.txt | 2 ++
drivers/mtd/nand/omap2.c | 29 ++++++++++++++--------
include/linux/platform_data/mtd-nand-omap2.h | 2 +-
3 files changed, 21 insertions(+), 12 deletions(-)
diff --git a/Documentation/devicetree/bindings/mtd/gpmc-nand.txt b/Documentation/devicetree/bindings/mtd/gpmc-nand.txt
index 810b87b..256bb86 100644
--- a/Documentation/devicetree/bindings/mtd/gpmc-nand.txt
+++ b/Documentation/devicetree/bindings/mtd/gpmc-nand.txt
@@ -48,6 +48,7 @@ Optional properties:
locating ECC errors for BCHx algorithms. SoC devices which have
ELM hardware engines should specify this device node in .dtsi
Using ELM for ECC error correction frees some CPU cycles.
+ - rb-gpios: GPIO specifier for the ready/busy# pin.
For inline partition table parsing (optional):
@@ -78,6 +79,7 @@ Example for an AM33xx board:
ti,nand-xfer-type = "polled";
interrupt-parent = <&gpmc>;
interrupts = <0>, <1>;
+ rb-gpios = <&gpmc 0 GPIO_ACTIVE_HIGH>; /* gpmc_wait0 */
gpmc,sync-clk-ps = <0>;
gpmc,cs-on-ns = <0>;
diff --git a/drivers/mtd/nand/omap2.c b/drivers/mtd/nand/omap2.c
index 0a637c4..e7939f1 100644
--- a/drivers/mtd/nand/omap2.c
+++ b/drivers/mtd/nand/omap2.c
@@ -12,6 +12,7 @@
#include <linux/dmaengine.h>
#include <linux/dma-mapping.h>
#include <linux/delay.h>
+#include <linux/gpio/consumer.h>
#include <linux/module.h>
#include <linux/interrupt.h>
#include <linux/jiffies.h>
@@ -183,6 +184,8 @@ struct omap_nand_info {
struct nand_ecclayout oobinfo;
/* fields specific for BCHx_HW ECC scheme */
struct device *elm_dev;
+ /* NAND ready gpio */
+ struct gpio_desc *ready_gpiod;
};
static inline struct omap_nand_info *mtd_to_omap(struct mtd_info *mtd)
@@ -1024,21 +1027,16 @@ static int omap_wait(struct mtd_info *mtd, struct nand_chip *chip)
}
/**
- * omap_dev_ready - calls the platform specific dev_ready function
+ * omap_dev_ready - checks the NAND Ready GPIO line
* @mtd: MTD device structure
+ *
+ * Returns true if ready and false if busy.
*/
static int omap_dev_ready(struct mtd_info *mtd)
{
- unsigned int val = 0;
struct omap_nand_info *info = mtd_to_omap(mtd);
- val = readl(info->reg.gpmc_status);
-
- if ((val & 0x100) == 0x100) {
- return 1;
- } else {
- return 0;
- }
+ return gpiod_get_value(info->ready_gpiod);
}
/**
@@ -1754,7 +1752,9 @@ static int omap_nand_probe(struct platform_device *pdev)
info->gpmc_cs = pdata->cs;
info->reg = pdata->reg;
info->ecc_opt = pdata->ecc_opt;
- info->dev_ready = pdata->dev_ready;
+ if (pdata->dev_ready)
+ dev_info(&pdev->dev, "pdata->dev_ready is deprecated\n");
+
info->xfer_type = pdata->xfer_type;
info->devsize = pdata->devsize;
info->elm_of_node = pdata->elm_of_node;
@@ -1786,6 +1786,13 @@ static int omap_nand_probe(struct platform_device *pdev)
nand_chip->IO_ADDR_W = nand_chip->IO_ADDR_R;
nand_chip->cmd_ctrl = omap_hwcontrol;
+ info->ready_gpiod = devm_gpiod_get_optional(&pdev->dev, "rb",
+ GPIOD_IN);
+ if (IS_ERR(info->ready_gpiod)) {
+ dev_err(dev, "failed to get ready gpio\n");
+ return PTR_ERR(info->ready_gpiod);
+ }
+
/*
* If RDY/BSY line is connected to OMAP then use the omap ready
* function and the generic nand_wait function which reads the status
@@ -1793,7 +1800,7 @@ static int omap_nand_probe(struct platform_device *pdev)
* chip delay which is slightly more than tR (AC Timing) of the NAND
* device and read status register until you get a failure or success
*/
- if (info->dev_ready) {
+ if (info->ready_gpiod) {
nand_chip->dev_ready = omap_dev_ready;
nand_chip->chip_delay = 0;
} else {
diff --git a/include/linux/platform_data/mtd-nand-omap2.h b/include/linux/platform_data/mtd-nand-omap2.h
index 7f6de53..17d57a1 100644
--- a/include/linux/platform_data/mtd-nand-omap2.h
+++ b/include/linux/platform_data/mtd-nand-omap2.h
@@ -71,7 +71,6 @@ struct omap_nand_platform_data {
int cs;
struct mtd_partition *parts;
int nr_parts;
- bool dev_ready;
bool flash_bbt;
enum nand_io xfer_type;
int devsize;
@@ -82,5 +81,6 @@ struct omap_nand_platform_data {
/* deprecated */
struct gpmc_nand_regs reg;
struct device_node *of_node;
+ bool dev_ready;
};
#endif
--
2.1.4
next prev parent reply other threads:[~2016-02-19 21:17 UTC|newest]
Thread overview: 55+ messages / expand[flat|nested] mbox.gz Atom feed top
2016-02-19 21:15 [PATCH v5 00/26] memory: omap-gpmc: mtd: nand: Support GPMC NAND on non-OMAP platforms Roger Quadros
2016-02-19 21:15 ` [PATCH v5 01/26] ARM: OMAP2+: gpmc: Add platform data Roger Quadros
2016-02-19 21:15 ` [PATCH v5 02/26] ARM: OMAP2+: gpmc: Add gpmc timings and settings to " Roger Quadros
2016-02-19 21:15 ` [PATCH v5 03/26] memory: omap-gpmc: Introduce GPMC to NAND interface Roger Quadros
2016-03-05 1:35 ` Brian Norris
2016-03-07 8:55 ` Roger Quadros
2016-02-19 21:15 ` [PATCH v5 04/26] mtd: nand: omap2: Use gpmc_omap_get_nand_ops() to get NAND registers Roger Quadros
2016-02-19 21:15 ` [PATCH v5 05/26] memory: omap-gpmc: Add GPMC-NAND ops to get writebufferempty status Roger Quadros
2016-02-19 21:15 ` [PATCH v5 06/26] mtd: nand: omap2: Switch to using GPMC-NAND ops for writebuffer empty check Roger Quadros
2016-02-19 21:15 ` [PATCH v5 07/26] memory: omap-gpmc: Implement IRQ domain for NAND IRQs Roger Quadros
2016-02-19 21:15 ` [PATCH v5 08/26] mtd: nand: omap: Copy platform data parameters to omap_nand_info data Roger Quadros
2016-02-19 21:15 ` [PATCH v5 09/26] mtd: nand: omap: Clean up device tree support Roger Quadros
2016-03-05 2:10 ` Brian Norris
2016-03-07 9:06 ` Roger Quadros
2016-03-05 2:28 ` Brian Norris
2016-03-07 9:02 ` Roger Quadros
2016-02-19 21:15 ` [PATCH v5 10/26] mtd: nand: omap: Update DT binding documentation Roger Quadros
2016-02-23 19:41 ` Rob Herring
2016-02-24 9:55 ` Roger Quadros
2016-03-05 2:04 ` Brian Norris
2016-03-07 9:46 ` Roger Quadros
2016-03-07 18:58 ` Brian Norris
2016-03-07 10:32 ` [PATCH v6 " Roger Quadros
2016-03-17 14:48 ` Rob Herring
2016-02-19 21:15 ` [PATCH v5 11/26] memory: omap-gpmc: Prevent mapping into 1st 16MB Roger Quadros
2016-02-19 21:15 ` [PATCH v5 12/26] memory: omap-gpmc: Move device tree binding to correct location Roger Quadros
2016-02-23 20:50 ` Rob Herring
2016-02-24 9:51 ` Roger Quadros
2016-02-19 21:15 ` [PATCH v5 13/26] memory: omap-gpmc: Support general purpose input for WAITPINs Roger Quadros
2016-03-07 9:34 ` Boris Brezillon
2016-03-07 9:38 ` Boris Brezillon
2016-03-07 10:02 ` Roger Quadros
2016-03-07 10:31 ` Boris Brezillon
2016-02-19 21:15 ` [PATCH v5 14/26] memory: omap-gpmc: Reserve WAITPIN if needed for WAIT monitoring Roger Quadros
2016-02-19 21:15 ` [PATCH v5 15/26] memory: omap-gpmc: Support WAIT pin edge interrupts Roger Quadros
2016-02-19 21:15 ` [PATCH v5 16/26] memory: omap-gpmc: Prevent GPMC_STATUS from being accessed via gpmc_regs Roger Quadros
2016-02-19 21:15 ` Roger Quadros [this message]
2016-03-05 1:46 ` [PATCH v5 17/26] mtd: nand: omap2: Implement NAND ready using gpiolib Brian Norris
2016-03-07 9:11 ` Roger Quadros
2016-03-07 9:22 ` Boris Brezillon
2016-02-19 21:15 ` [PATCH v5 18/26] ARM: dts: dra7: Fix NAND device nodes Roger Quadros
2016-02-19 21:15 ` [PATCH v5 19/26] ARM: dts: dra7x-evm: Provide NAND ready pin Roger Quadros
2016-02-19 21:15 ` [PATCH v5 20/26] ARM: dts: am437x: Fix NAND device nodes Roger Quadros
2016-02-19 21:15 ` [PATCH v5 21/26] ARM: dts: am437x: Provide NAND ready pin Roger Quadros
2016-02-19 21:15 ` [PATCH v5 22/26] ARM: dts: am335x: Fix NAND device nodes Roger Quadros
2016-02-19 21:15 ` [PATCH v5 23/26] ARM: dts: am335x: Provide NAND ready pin Roger Quadros
2016-02-19 21:15 ` [PATCH v5 24/26] ARM: dts: dm814x: Fix gpmc and NAND node Roger Quadros
2016-02-19 21:15 ` [PATCH v5 25/26] ARM: dts: dm816x: " Roger Quadros
2016-02-19 21:15 ` [PATCH v5 26/26] ARM: dts: omap3: Fix gpmc and NAND nodes Roger Quadros
2016-02-19 22:04 ` [PATCH v5 00/26] memory: omap-gpmc: mtd: nand: Support GPMC NAND on non-OMAP platforms Tony Lindgren
2016-02-22 10:15 ` Roger Quadros
2016-02-22 16:42 ` Tony Lindgren
2016-02-22 20:05 ` Roger Quadros
2016-02-29 16:25 ` Roger Quadros
2016-03-05 2:33 ` Brian Norris
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1455916548-3441-18-git-send-email-rogerq@ti.com \
--to=rogerq@ti.com \
--cc=computersforpeace@gmail.com \
--cc=devicetree@vger.kernel.org \
--cc=dwmw2@infradead.org \
--cc=ezequiel@vanguardiasur.com.ar \
--cc=fcooper@ti.com \
--cc=javier@dowhile0.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-mtd@lists.infradead.org \
--cc=linux-omap@vger.kernel.org \
--cc=nsekhar@ti.com \
--cc=tony@atomide.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).