From: "Lothar Waßmann" <LW@KARO-electronics.de>
To: Fabio Estevam <fabio.estevam@nxp.com>,
Mark Rutland <mark.rutland@arm.com>,
Rob Herring <robh+dt@kernel.org>,
Russell King <linux@armlinux.org.uk>,
Sascha Hauer <kernel@pengutronix.de>,
Shawn Guo <shawnguo@kernel.org>,
devicetree@vger.kernel.org, linux-arm-kernel@lists.infradead.org,
linux-kernel@vger.kernel.org
Cc: "Lothar Waßmann" <LW@KARO-electronics.de>
Subject: [PATCH 2/7] ARM: dts: imx53-tx53: remove the regulators bus
Date: Wed, 11 Oct 2017 13:07:36 +0200 [thread overview]
Message-ID: <1507720061-27666-3-git-send-email-LW@KARO-electronics.de> (raw)
In-Reply-To: <1507720061-27666-1-git-send-email-LW@KARO-electronics.de>
It is not recommended to place the regulator nodes inside 'simple-bus',
so adjust them accordingly.
The motivation for rearranging this is to make it easier to add new
regulator nodes in the future.
Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
---
arch/arm/boot/dts/imx53-tx53-x03x.dts | 38 +++++++--------
arch/arm/boot/dts/imx53-tx53-x13x.dts | 38 +++++++--------
arch/arm/boot/dts/imx53-tx53.dtsi | 91 +++++++++++++++--------------------
3 files changed, 74 insertions(+), 93 deletions(-)
diff --git a/arch/arm/boot/dts/imx53-tx53-x03x.dts b/arch/arm/boot/dts/imx53-tx53-x03x.dts
index 7f0a7dd..aa9ae84 100644
--- a/arch/arm/boot/dts/imx53-tx53-x03x.dts
+++ b/arch/arm/boot/dts/imx53-tx53-x03x.dts
@@ -203,28 +203,24 @@
default-brightness-level = <50>;
};
- regulators {
- reg_lcd_pwr: regulator@5 {
- compatible = "regulator-fixed";
- reg = <5>;
- regulator-name = "LCD POWER";
- regulator-min-microvolt = <3300000>;
- regulator-max-microvolt = <3300000>;
- gpio = <&gpio2 31 GPIO_ACTIVE_HIGH>;
- enable-active-high;
- regulator-boot-on;
- };
+ reg_lcd_pwr: regulator-lcd-pwr {
+ compatible = "regulator-fixed";
+ regulator-name = "LCD POWER";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ gpio = <&gpio2 31 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ regulator-boot-on;
+ };
- reg_lcd_reset: regulator@6 {
- compatible = "regulator-fixed";
- reg = <6>;
- regulator-name = "LCD RESET";
- regulator-min-microvolt = <3300000>;
- regulator-max-microvolt = <3300000>;
- gpio = <&gpio3 29 GPIO_ACTIVE_HIGH>;
- enable-active-high;
- regulator-boot-on;
- };
+ reg_lcd_reset: regulator-lcd-reset {
+ compatible = "regulator-fixed";
+ regulator-name = "LCD RESET";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ gpio = <&gpio3 29 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ regulator-boot-on;
};
};
diff --git a/arch/arm/boot/dts/imx53-tx53-x13x.dts b/arch/arm/boot/dts/imx53-tx53-x13x.dts
index 62670e9..0d17c80 100644
--- a/arch/arm/boot/dts/imx53-tx53-x13x.dts
+++ b/arch/arm/boot/dts/imx53-tx53-x13x.dts
@@ -99,28 +99,24 @@
default-brightness-level = <50>;
};
- regulators {
- reg_lcd_pwr0: regulator@5 {
- compatible = "regulator-fixed";
- reg = <5>;
- regulator-name = "LVDS0 POWER";
- regulator-min-microvolt = <3300000>;
- regulator-max-microvolt = <3300000>;
- gpio = <&gpio3 29 GPIO_ACTIVE_HIGH>;
- enable-active-high;
- regulator-boot-on;
- };
+ reg_lcd_pwr0: regulator-lvds0-pwr {
+ compatible = "regulator-fixed";
+ regulator-name = "LVDS0 POWER";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ gpio = <&gpio3 29 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ regulator-boot-on;
+ };
- reg_lcd_pwr1: regulator@6 {
- compatible = "regulator-fixed";
- reg = <6>;
- regulator-name = "LVDS1 POWER";
- regulator-min-microvolt = <3300000>;
- regulator-max-microvolt = <3300000>;
- gpio = <&gpio2 31 GPIO_ACTIVE_HIGH>;
- enable-active-high;
- regulator-boot-on;
- };
+ reg_lcd_pwr1: regulator-lvds1-pwr {
+ compatible = "regulator-fixed";
+ regulator-name = "LVDS1 POWER";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ gpio = <&gpio2 31 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ regulator-boot-on;
};
};
diff --git a/arch/arm/boot/dts/imx53-tx53.dtsi b/arch/arm/boot/dts/imx53-tx53.dtsi
index 7577016..a3e7cf9 100644
--- a/arch/arm/boot/dts/imx53-tx53.dtsi
+++ b/arch/arm/boot/dts/imx53-tx53.dtsi
@@ -96,61 +96,50 @@
};
};
- regulators {
- compatible = "simple-bus";
- #address-cells = <1>;
- #size-cells = <0>;
-
- reg_2v5: regulator@0 {
- compatible = "regulator-fixed";
- reg = <0>;
- regulator-name = "2V5";
- regulator-min-microvolt = <2500000>;
- regulator-max-microvolt = <2500000>;
- };
+ reg_2v5: regulator-2v5 {
+ compatible = "regulator-fixed";
+ regulator-name = "2V5";
+ regulator-min-microvolt = <2500000>;
+ regulator-max-microvolt = <2500000>;
+ };
- reg_3v3: regulator@1 {
- compatible = "regulator-fixed";
- reg = <1>;
- regulator-name = "3V3";
- regulator-min-microvolt = <3300000>;
- regulator-max-microvolt = <3300000>;
- };
+ reg_3v3: regulator-3v3 {
+ compatible = "regulator-fixed";
+ regulator-name = "3V3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ };
- reg_can_xcvr: regulator@2 {
- compatible = "regulator-fixed";
- reg = <2>;
- regulator-name = "CAN XCVR";
- regulator-min-microvolt = <3300000>;
- regulator-max-microvolt = <3300000>;
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_can_xcvr>;
- gpio = <&gpio4 21 GPIO_ACTIVE_HIGH>;
- };
+ reg_can_xcvr: regulator-can-xcvr {
+ compatible = "regulator-fixed";
+ regulator-name = "CAN XCVR";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_can_xcvr>;
+ gpio = <&gpio4 21 GPIO_ACTIVE_HIGH>;
+ };
- reg_usbh1_vbus: regulator@3 {
- compatible = "regulator-fixed";
- reg = <3>;
- regulator-name = "usbh1_vbus";
- regulator-min-microvolt = <5000000>;
- regulator-max-microvolt = <5000000>;
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_usbh1_vbus>;
- gpio = <&gpio3 31 GPIO_ACTIVE_HIGH>;
- enable-active-high;
- };
+ reg_usbh1_vbus: regulator-usbh1-vbus {
+ compatible = "regulator-fixed";
+ regulator-name = "usbh1_vbus";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usbh1_vbus>;
+ gpio = <&gpio3 31 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ };
- reg_usbotg_vbus: regulator@4 {
- compatible = "regulator-fixed";
- reg = <4>;
- regulator-name = "usbotg_vbus";
- regulator-min-microvolt = <5000000>;
- regulator-max-microvolt = <5000000>;
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_usbotg_vbus>;
- gpio = <&gpio1 7 GPIO_ACTIVE_HIGH>;
- enable-active-high;
- };
+ reg_usbotg_vbus: regulator-usbotg-vbus {
+ compatible = "regulator-fixed";
+ regulator-name = "usbotg_vbus";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usbotg_vbus>;
+ gpio = <&gpio1 7 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
};
sound {
--
2.1.4
next prev parent reply other threads:[~2017-10-11 13:07 UTC|newest]
Thread overview: 9+ messages / expand[flat|nested] mbox.gz Atom feed top
2017-10-11 11:07 [PATCH 0/7] ARM: dts: imx53: Update Update Ka-Ro TX53 dts files Lothar Waßmann
2017-10-11 11:07 ` [PATCH 1/7] ARM: dts: imx53-tx53: Relicense the TX53 dts files under GPLv2/X11 Lothar Waßmann
2017-10-11 11:07 ` Lothar Waßmann [this message]
2017-10-11 11:07 ` [PATCH 3/7] ARM: dts: imx53-tx53: remove obsolete eeti,egalax_ts Lothar Waßmann
2017-10-11 11:07 ` [PATCH 4/7] ARM: dts: imx53-tx53: add trickle-charge config for DS1339 Lothar Waßmann
2017-10-11 11:07 ` [PATCH 5/7] ARM: dts: imx53-tx53: use explicit pad_ctl settings for I2C pins Lothar Waßmann
2017-10-11 11:07 ` [PATCH 6/7] ARM: dts: imx53-tx53: add support for I2C bus recovery Lothar Waßmann
2017-10-11 11:07 ` [PATCH 7/7] ARM: dts: imx53-tx53: fix interrupt flags and use interrupts-extended property Lothar Waßmann
2017-10-14 15:11 ` [PATCH 0/7] ARM: dts: imx53: Update Update Ka-Ro TX53 dts files Shawn Guo
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1507720061-27666-3-git-send-email-LW@KARO-electronics.de \
--to=lw@karo-electronics.de \
--cc=devicetree@vger.kernel.org \
--cc=fabio.estevam@nxp.com \
--cc=kernel@pengutronix.de \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux@armlinux.org.uk \
--cc=mark.rutland@arm.com \
--cc=robh+dt@kernel.org \
--cc=shawnguo@kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox