[PATCH v2 2/2] drivers: thermal: Move QCOM_SPMI_TEMP_ALARM into the qcom subdir

Amit Kucheria
2018-10-04T07:52:36Z

This cleans up the directory a bit allowing just one place to look for
thermal related drivers for QCOM platforms instead of being scattered in
the root directory and the qcom/ subdirectory. Compile-tested with
ARCH=arm64 defconfig and the driver explicitly enabled with menuconfig.

Signed-off-by: Amit Kucheria <amit.kucheria@linaro.org>
Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org>
---
drivers/thermal/Kconfig | 11 -----------
drivers/thermal/Makefile | 1 -
drivers/thermal/qcom/Kconfig | 11 +++++++++++
drivers/thermal/qcom/Makefile | 1 +
drivers/thermal/{ => qcom}/qcom-spmi-temp-alarm.c | 0
5 files changed, 12 insertions(+), 12 deletions(-)
rename drivers/thermal/{ => qcom}/qcom-spmi-temp-alarm.c (100%)

diff --git a/drivers/thermal/Kconfig b/drivers/thermal/Kconfig
index 6f18110f1480..c075f1190e63 100644
--- a/drivers/thermal/Kconfig
+++ b/drivers/thermal/Kconfig
@@ -374,17 +374,6 @@ config TANGO_THERMAL

source "drivers/thermal/tegra/Kconfig"

-config QCOM_SPMI_TEMP_ALARM
- tristate "Qualcomm SPMI PMIC Temperature Alarm"
- depends on OF && SPMI && IIO
- select REGMAP_SPMI
- help
- This enables a thermal sysfs driver for Qualcomm plug-and-play (QPNP)
- PMIC devices. It shows up in sysfs as a thermal sensor with multiple
- trip points. The temperature reported by the thermal sensor reflects the
- real time die temperature if an ADC is present or an estimate of the
- temperature based upon the over temperature stage value.
-
config GENERIC_ADC_THERMAL
tristate "Generic ADC based thermal sensor"
depends on IIO
diff --git a/drivers/thermal/Makefile b/drivers/thermal/Makefile
index 031f61e7dfe8..415361685480 100644
--- a/drivers/thermal/Makefile
+++ b/drivers/thermal/Makefile
@@ -29,7 +29,6 @@ thermal_sys-$(CONFIG_DEVFREQ_THERMAL) += devfreq_cooling.o

# platform thermal drivers
obj-y += broadcom/
-obj-$(CONFIG_QCOM_SPMI_TEMP_ALARM) += qcom-spmi-temp-alarm.o
obj-$(CONFIG_SPEAR_THERMAL) += spear_thermal.o
obj-$(CONFIG_ROCKCHIP_THERMAL) += rockchip_thermal.o
obj-$(CONFIG_RCAR_THERMAL) += rcar_thermal.o
diff --git a/drivers/thermal/qcom/Kconfig b/drivers/thermal/qcom/Kconfig
index be32e5abce3c..cdb455ffd575 100644
--- a/drivers/thermal/qcom/Kconfig
+++ b/drivers/thermal/qcom/Kconfig
@@ -9,3 +9,14 @@ config QCOM_TSENS
thermal zone device via the mode file results in disabling the sensor.
Also able to set threshold temperature for both hot and cold and update
when a threshold is reached.
+
+config QCOM_SPMI_TEMP_ALARM
+ tristate "Qualcomm SPMI PMIC Temperature Alarm"
+ depends on OF && SPMI && IIO
+ select REGMAP_SPMI
+ help
+ This enables a thermal sysfs driver for Qualcomm plug-and-play (QPNP)
+ PMIC devices. It shows up in sysfs as a thermal sensor with multiple
+ trip points. The temperature reported by the thermal sensor reflects the
+ real time die temperature if an ADC is present or an estimate of the
+ temperature based upon the over temperature stage value.
diff --git a/drivers/thermal/qcom/Makefile b/drivers/thermal/qcom/Makefile
index a821929ede0b..717a08600bb5 100644
--- a/drivers/thermal/qcom/Makefile
+++ b/drivers/thermal/qcom/Makefile
@@ -1,2 +1,3 @@
obj-$(CONFIG_QCOM_TSENS) += qcom_tsens.o
qcom_tsens-y += tsens.o tsens-common.o tsens-8916.o tsens-8974.o tsens-8960.o tsens-v2.o
+obj-$(CONFIG_QCOM_SPMI_TEMP_ALARM) += qcom-spmi-temp-alarm.o
diff --git a/drivers/thermal/qcom-spmi-temp-alarm.c b/drivers/thermal/qcom/qcom-spmi-temp-alarm.c
similarity index 100%
rename from drivers/thermal/qcom-spmi-temp-alarm.c
rename to drivers/thermal/qcom/qcom-spmi-temp-alarm.c
--
2.17.1