[PATCH v8 4/5] phy: qcom-qmp: Use proper PWRDOWN offset for sm8150 USB

Wesley Cheng
2020-05-04T23:55:06Z

The register map for SM8150 QMP USB SSPHY has moved
QPHY_POWER_DOWN_CONTROL to a different offset. Allow for
an offset in the register table to override default value
if it is a DP capable PHY.

Signed-off-by: Wesley Cheng <wcheng@codeaurora.org>
Reviewed-by: Manu Gautam <mgautam@codeaurora.org>
---
drivers/phy/qualcomm/phy-qcom-qmp.c | 23 +++++++++++++++++++----
1 file changed, 19 insertions(+), 4 deletions(-)

diff --git a/drivers/phy/qualcomm/phy-qcom-qmp.c b/drivers/phy/qualcomm/phy-qcom-qmp.c
index d62bd09..dec4a17 100644
--- a/drivers/phy/qualcomm/phy-qcom-qmp.c
+++ b/drivers/phy/qualcomm/phy-qcom-qmp.c
@@ -119,6 +119,7 @@ enum qphy_reg_layout {
QPHY_PCS_AUTONOMOUS_MODE_CTRL,
QPHY_PCS_LFPS_RXTERM_IRQ_CLEAR,
QPHY_PCS_LFPS_RXTERM_IRQ_STATUS,
+ QPHY_PCS_POWER_DOWN_CONTROL,
};

static const unsigned int msm8996_ufsphy_regs_layout[] = {
@@ -181,6 +182,7 @@ enum qphy_reg_layout {
[QPHY_SW_RESET] = 0x00,
[QPHY_START_CTRL] = 0x44,
[QPHY_PCS_STATUS] = 0x14,
+ [QPHY_PCS_POWER_DOWN_CONTROL] = 0x40,
};

static const unsigned int sdm845_ufsphy_regs_layout[] = {
@@ -2030,11 +2032,18 @@ static int qcom_qmp_phy_com_init(struct qmp_phy *qphy)
SW_USB3PHY_RESET_MUX | SW_USB3PHY_RESET);
}

- if (cfg->has_phy_com_ctrl)
+ if (cfg->has_phy_com_ctrl) {
qphy_setbits(serdes, cfg->regs[QPHY_COM_POWER_DOWN_CONTROL],
SW_PWRDN);
- else
- qphy_setbits(pcs, QPHY_POWER_DOWN_CONTROL, cfg->pwrdn_ctrl);
+ } else {
+ if (cfg->regs[QPHY_PCS_POWER_DOWN_CONTROL])
+ qphy_setbits(pcs,
+ cfg->regs[QPHY_PCS_POWER_DOWN_CONTROL],
+ cfg->pwrdn_ctrl);
+ else
+ qphy_setbits(pcs, QPHY_POWER_DOWN_CONTROL,
+ cfg->pwrdn_ctrl);
+ }

/* Serdes configuration */
qcom_qmp_phy_configure(serdes, cfg->regs, cfg->serdes_tbl,
@@ -2260,7 +2269,13 @@ static int qcom_qmp_phy_disable(struct phy *phy)
qphy_clrbits(qphy->pcs, cfg->regs[QPHY_START_CTRL], cfg->start_ctrl);

/* Put PHY into POWER DOWN state: active low */
- qphy_clrbits(qphy->pcs, QPHY_POWER_DOWN_CONTROL, cfg->pwrdn_ctrl);
+ if (cfg->regs[QPHY_PCS_POWER_DOWN_CONTROL]) {
+ qphy_clrbits(qphy->pcs, cfg->regs[QPHY_PCS_POWER_DOWN_CONTROL],
+ cfg->pwrdn_ctrl);
+ } else {
+ qphy_clrbits(qphy->pcs, QPHY_POWER_DOWN_CONTROL,
+ cfg->pwrdn_ctrl);
+ }

if (cfg->has_lane_rst)
reset_control_assert(qphy->lane_rst);