[PATCH v2] arch: arm: imx6qdl-icore: Fix OTG_ID pin and sdcard detect

Suniel Mahesh
2020-06-20T03:28:40Z

From: Michael Trimarchi <michael@amarulasolutions.com>

The current pin muxing scheme muxes GPIO_1 pad for USB_OTG_ID
because of which when card is inserted, usb otg is enumerated
and the card is never detected.

[ 64.492645] cfg80211: failed to load regulatory.db
[ 64.492657] imx-sdma 20ec000.sdma: external firmware not found, using ROM firmware
[ 76.343711] ci_hdrc ci_hdrc.0: EHCI Host Controller
[ 76.349742] ci_hdrc ci_hdrc.0: new USB bus registered, assigned bus number 2
[ 76.388862] ci_hdrc ci_hdrc.0: USB 2.0 started, EHCI 1.00
[ 76.396650] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.08
[ 76.405412] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 76.412763] usb usb2: Product: EHCI Host Controller
[ 76.417666] usb usb2: Manufacturer: Linux 5.8.0-rc1-next-20200618 ehci_hcd
[ 76.424623] usb usb2: SerialNumber: ci_hdrc.0
[ 76.431755] hub 2-0:1.0: USB hub found
[ 76.435862] hub 2-0:1.0: 1 port detected

The TRM mentions GPIO_1 pad should be muxed/assigned for card detect
and ENET_RX_ER pad for USB_OTG_ID for proper operation.

This patch fixes pin muxing as per TRM and is tested on a
i.Core 1.5 MX6 DL SOM.

[ 22.449165] mmc0: host does not support reading read-only switch, assuming write-enable
[ 22.459992] mmc0: new high speed SDHC card at address 0001
[ 22.469725] mmcblk0: mmc0:0001 EB1QT 29.8 GiB
[ 22.478856] mmcblk0: p1 p2

Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Suniel Mahesh <sunil@amarulasolutions.com>
---
Changes for v2:
- Changed patch description as suggested by Michael Trimarchi to make it
more readable/understandable.
---
arch/arm/boot/dts/imx6qdl-icore.dtsi | 3 ++-
1 file changed, 2 insertions(+), 1 deletion(-)

diff --git a/arch/arm/boot/dts/imx6qdl-icore.dtsi b/arch/arm/boot/dts/imx6qdl-icore.dtsi
index 756f3a9..12997da 100644
--- a/arch/arm/boot/dts/imx6qdl-icore.dtsi
+++ b/arch/arm/boot/dts/imx6qdl-icore.dtsi
@@ -397,7 +397,7 @@

pinctrl_usbotg: usbotggrp {
fsl,pins = <
- MX6QDL_PAD_GPIO_1__USB_OTG_ID 0x17059
+ MX6QDL_PAD_ENET_RX_ER__USB_OTG_ID 0x17059
>;
};

@@ -409,6 +409,7 @@
MX6QDL_PAD_SD1_DAT1__SD1_DATA1 0x17070
MX6QDL_PAD_SD1_DAT2__SD1_DATA2 0x17070
MX6QDL_PAD_SD1_DAT3__SD1_DATA3 0x17070
+ MX6QDL_PAD_GPIO_1__GPIO1_IO01 0x1b0b0
>;
};

--
2.7.4