Re: [PATCH v2 0/5] Add support of SECVIO from SNVS on iMX8q/x

Franck LENORMAND (OSS)
2020-08-18T07:52:15Z

Hello,

Peng was able to do a firt pass of review on my patchset which led to this
second version. I hope a maintainer will be able to take a look at this
patchset once rested after all the work they did for 5.9.

On mar., 2020-07-21 at 17:20 +0200, franck.lenormand@oss.nxp.com wrote:
> From: Franck LENORMAND <franck.lenormand@oss.nxp.com>
>
> This patchset aims to add support for the SECurity VIOlation (SECVIO) of the
> SNVS. A secvio is a signal emitted by the SNVS when a hardware attack
> is detected. On imx8x and imx8q SoC, the SNVS is controlled by the
> SECO and it is possible to interact with it using the SCU using the SC APIs.
>
> For the driver to communicate with the SNVS via the SCU and the SECO, I had to:
>  - Add support for exchange of big message with the SCU (needed for
> imx_scu_irq_get_status)
>  - Add API to check linux can control the SECVIO (imx_sc_rm_is_resource_owned)
>  - Add APIs for the driver to read the state of the SECVIO registers of the
> SNVS and DGO (imx_sc_seco_secvio_enable and imx_sc_seco_secvio_enable).
>
> To check the state of the SECVIO IRQ in the SCU, I added the
> imx_scu_irq_get_status API.
>
> The secvio driver is designed to receive the IRQ produced by the
> SNVS in case of hardware attack and notify the status to the
> audit framework which can be used by the user.
>
> The goal of the driver is to be self suficient but can be extended by the
> user to perform custom operations on values read (imx_sc_seco_secvio_enable)
>
> v2:
>  - Removed (firmware: imx: scu-rm: Add Resource Management APIs)
> -> Code required is already present
>  - Removed (firmware: imx: scu: Support reception of messages of any size)
> -> The imx-scu is already working in fast-ipc mode
>  - (soc: imx8: Add the SC SECVIO driver):
> - Fixed the warnings reported by kernel test robot
>
> Franck LENORMAND (5):
>   firmware: imx: scu-seco: Add SEcure Controller APIS
>   firmware: imx: scu-irq: Add API to retrieve status of IRQ
>   dt-bindings: firmware: imx-scu: Add SECVIO resource
>   dt-bindings: arm: imx: Documentation of the SC secvio driver
>   soc: imx8: Add the SC SECVIO driver
>
>  .../bindings/arm/freescale/fsl,imx-sc-secvio.yaml  |  34 +
>  drivers/firmware/imx/Makefile                      |   2 +-
>  drivers/firmware/imx/imx-scu-irq.c                 |  37 +-
>  drivers/firmware/imx/imx-scu.c                     |   3 +
>  drivers/firmware/imx/seco.c                        | 275 +++++++
>  drivers/soc/imx/Kconfig                            |  10 +
>  drivers/soc/imx/Makefile                           |   1 +
>  drivers/soc/imx/secvio/Kconfig                     |  10 +
>  drivers/soc/imx/secvio/Makefile                    |   3 +
>  drivers/soc/imx/secvio/imx-secvio-audit.c          |  39 +
>  drivers/soc/imx/secvio/imx-secvio-debugfs.c        | 379 +++++++++
>  drivers/soc/imx/secvio/imx-secvio-sc-int.h         |  84 ++
>  drivers/soc/imx/secvio/imx-secvio-sc.c             | 858 +++++++++++++++++++++
>  include/dt-bindings/firmware/imx/rsrc.h            |   3 +-
>  include/linux/firmware/imx/ipc.h                   |   1 +
>  include/linux/firmware/imx/sci.h                   |   5 +
>  include/linux/firmware/imx/svc/seco.h              |  73 ++
>  include/soc/imx/imx-secvio-sc.h                    | 177 +++++
>  18 files changed, 1991 insertions(+), 3 deletions(-)
>  create mode 100644 Documentation/devicetree/bindings/arm/freescale/fsl,imx-sc-
> secvio.yaml
>  create mode 100644 drivers/firmware/imx/seco.c
>  create mode 100644 drivers/soc/imx/secvio/Kconfig
>  create mode 100644 drivers/soc/imx/secvio/Makefile
>  create mode 100644 drivers/soc/imx/secvio/imx-secvio-audit.c
>  create mode 100644 drivers/soc/imx/secvio/imx-secvio-debugfs.c
>  create mode 100644 drivers/soc/imx/secvio/imx-secvio-sc-int.h
>  create mode 100644 drivers/soc/imx/secvio/imx-secvio-sc.c
>  create mode 100644 include/linux/firmware/imx/svc/seco.h
>  create mode 100644 include/soc/imx/imx-secvio-sc.h
>