* [PATCH v2 01/12] bus: mhi: core: Use appropriate names for firmware load functions
2020-10-30 1:51 [PATCH v2 00/12] Bug fixes and improvements for MHI power operations Bhaumik Bhatt
@ 2020-10-30 1:51 ` Bhaumik Bhatt
2020-10-30 1:51 ` [PATCH v2 02/12] bus: mhi: core: Move to using high priority workqueue Bhaumik Bhatt
` (10 subsequent siblings)
11 siblings, 0 replies; 13+ messages in thread
From: Bhaumik Bhatt @ 2020-10-30 1:51 UTC (permalink / raw)
To: manivannan.sadhasivam
Cc: linux-arm-msm, hemantk, jhugo, linux-kernel, Bhaumik Bhatt
mhi_fw_load_sbl() function is currently used to transfer SBL or EDL
images over BHI (Boot Host Interface). Same goes with mhi_fw_load_amss()
which uses BHIe. However, the contents of these functions do not
indicate support for a specific set of images. Since these can be used
for any image download over BHI or BHIe, rename them based on the
protocol used.
Signed-off-by: Bhaumik Bhatt <bbhatt@codeaurora.org>
---
drivers/bus/mhi/core/boot.c | 19 ++++++++++---------
1 file changed, 10 insertions(+), 9 deletions(-)
diff --git a/drivers/bus/mhi/core/boot.c b/drivers/bus/mhi/core/boot.c
index 24422f5..7d6b3a7 100644
--- a/drivers/bus/mhi/core/boot.c
+++ b/drivers/bus/mhi/core/boot.c
@@ -171,7 +171,7 @@ int mhi_download_rddm_img(struct mhi_controller *mhi_cntrl, bool in_panic)
}
EXPORT_SYMBOL_GPL(mhi_download_rddm_img);
-static int mhi_fw_load_amss(struct mhi_controller *mhi_cntrl,
+static int mhi_fw_load_bhie(struct mhi_controller *mhi_cntrl,
const struct mhi_buf *mhi_buf)
{
void __iomem *base = mhi_cntrl->bhie;
@@ -187,7 +187,7 @@ static int mhi_fw_load_amss(struct mhi_controller *mhi_cntrl,
}
sequence_id = MHI_RANDOM_U32_NONZERO(BHIE_TXVECSTATUS_SEQNUM_BMSK);
- dev_dbg(dev, "Starting AMSS download via BHIe. Sequence ID:%u\n",
+ dev_dbg(dev, "Starting image download via BHIe. Sequence ID: %u\n",
sequence_id);
mhi_write_reg(mhi_cntrl, base, BHIE_TXVECADDR_HIGH_OFFS,
upper_32_bits(mhi_buf->dma_addr));
@@ -218,7 +218,7 @@ static int mhi_fw_load_amss(struct mhi_controller *mhi_cntrl,
return (!ret) ? -ETIMEDOUT : 0;
}
-static int mhi_fw_load_sbl(struct mhi_controller *mhi_cntrl,
+static int mhi_fw_load_bhi(struct mhi_controller *mhi_cntrl,
dma_addr_t dma_addr,
size_t size)
{
@@ -245,7 +245,7 @@ static int mhi_fw_load_sbl(struct mhi_controller *mhi_cntrl,
}
session_id = MHI_RANDOM_U32_NONZERO(BHI_TXDB_SEQNUM_BMSK);
- dev_dbg(dev, "Starting SBL download via BHI. Session ID:%u\n",
+ dev_dbg(dev, "Starting image download via BHI. Session ID: %u\n",
session_id);
mhi_write_reg(mhi_cntrl, base, BHI_STATUS, 0);
mhi_write_reg(mhi_cntrl, base, BHI_IMGADDR_HIGH,
@@ -446,9 +446,9 @@ void mhi_fw_load_handler(struct mhi_controller *mhi_cntrl)
return;
}
- /* Download SBL image */
+ /* Download image using BHI */
memcpy(buf, firmware->data, size);
- ret = mhi_fw_load_sbl(mhi_cntrl, dma_addr, size);
+ ret = mhi_fw_load_bhi(mhi_cntrl, dma_addr, size);
mhi_free_coherent(mhi_cntrl, size, buf, dma_addr);
if (!mhi_cntrl->fbc_download || ret || mhi_cntrl->ee == MHI_EE_EDL)
@@ -456,7 +456,7 @@ void mhi_fw_load_handler(struct mhi_controller *mhi_cntrl)
/* Error or in EDL mode, we're done */
if (ret) {
- dev_err(dev, "MHI did not load SBL, ret:%d\n", ret);
+ dev_err(dev, "MHI did not load image over BHI, ret: %d\n", ret);
return;
}
@@ -506,11 +506,12 @@ void mhi_fw_load_handler(struct mhi_controller *mhi_cntrl)
/* Start full firmware image download */
image_info = mhi_cntrl->fbc_image;
- ret = mhi_fw_load_amss(mhi_cntrl,
+ ret = mhi_fw_load_bhie(mhi_cntrl,
/* Vector table is the last entry */
&image_info->mhi_buf[image_info->entries - 1]);
if (ret)
- dev_err(dev, "MHI did not load AMSS, ret:%d\n", ret);
+ dev_err(dev, "MHI did not load image over BHIe, ret: %d\n",
+ ret);
release_firmware(firmware);
--
The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum,
a Linux Foundation Collaborative Project
^ permalink raw reply related [flat|nested] 13+ messages in thread* [PATCH v2 02/12] bus: mhi: core: Move to using high priority workqueue
2020-10-30 1:51 [PATCH v2 00/12] Bug fixes and improvements for MHI power operations Bhaumik Bhatt
2020-10-30 1:51 ` [PATCH v2 01/12] bus: mhi: core: Use appropriate names for firmware load functions Bhaumik Bhatt
@ 2020-10-30 1:51 ` Bhaumik Bhatt
2020-10-30 1:51 ` [PATCH v2 03/12] bus: mhi: core: Skip device wake in error or shutdown states Bhaumik Bhatt
` (9 subsequent siblings)
11 siblings, 0 replies; 13+ messages in thread
From: Bhaumik Bhatt @ 2020-10-30 1:51 UTC (permalink / raw)
To: manivannan.sadhasivam
Cc: linux-arm-msm, hemantk, jhugo, linux-kernel, Bhaumik Bhatt
MHI work is currently scheduled on the global/system workqueue and can
encounter delays on a stressed system. To avoid those unforeseen
delays which can hamper bootup or shutdown times, use a dedicated high
priority workqueue instead of the global/system workqueue.
Signed-off-by: Bhaumik Bhatt <bbhatt@codeaurora.org>
---
drivers/bus/mhi/core/init.c | 8 ++++++++
drivers/bus/mhi/core/pm.c | 2 +-
include/linux/mhi.h | 2 ++
3 files changed, 11 insertions(+), 1 deletion(-)
diff --git a/drivers/bus/mhi/core/init.c b/drivers/bus/mhi/core/init.c
index 0ffdebd..23b6dd6 100644
--- a/drivers/bus/mhi/core/init.c
+++ b/drivers/bus/mhi/core/init.c
@@ -880,6 +880,13 @@ int mhi_register_controller(struct mhi_controller *mhi_cntrl,
INIT_WORK(&mhi_cntrl->st_worker, mhi_pm_st_worker);
init_waitqueue_head(&mhi_cntrl->state_event);
+ mhi_cntrl->hiprio_wq = alloc_ordered_workqueue
+ ("mhi_hiprio_wq", WQ_MEM_RECLAIM | WQ_HIGHPRI);
+ if (!mhi_cntrl->hiprio_wq) {
+ dev_err(mhi_cntrl->cntrl_dev, "Failed to allocate workqueue\n");
+ goto error_alloc_cmd;
+ }
+
mhi_cmd = mhi_cntrl->mhi_cmd;
for (i = 0; i < NR_OF_CMD_RINGS; i++, mhi_cmd++)
spin_lock_init(&mhi_cmd->lock);
@@ -969,6 +976,7 @@ int mhi_register_controller(struct mhi_controller *mhi_cntrl,
error_alloc_cmd:
vfree(mhi_cntrl->mhi_chan);
kfree(mhi_cntrl->mhi_event);
+ destroy_workqueue(mhi_cntrl->hiprio_wq);
return ret;
}
diff --git a/drivers/bus/mhi/core/pm.c b/drivers/bus/mhi/core/pm.c
index 3de7b16..805b6fa74 100644
--- a/drivers/bus/mhi/core/pm.c
+++ b/drivers/bus/mhi/core/pm.c
@@ -597,7 +597,7 @@ int mhi_queue_state_transition(struct mhi_controller *mhi_cntrl,
list_add_tail(&item->node, &mhi_cntrl->transition_list);
spin_unlock_irqrestore(&mhi_cntrl->transition_lock, flags);
- schedule_work(&mhi_cntrl->st_worker);
+ queue_work(mhi_cntrl->hiprio_wq, &mhi_cntrl->st_worker);
return 0;
}
diff --git a/include/linux/mhi.h b/include/linux/mhi.h
index d4841e5..8961cbc 100644
--- a/include/linux/mhi.h
+++ b/include/linux/mhi.h
@@ -337,6 +337,7 @@ struct mhi_controller_config {
* @wlock: Lock for protecting device wakeup
* @mhi_link_info: Device bandwidth info
* @st_worker: State transition worker
+ * @hiprio_wq: High priority workqueue for MHI work such as state transitions
* @state_event: State change event
* @status_cb: CB function to notify power states of the device (required)
* @wake_get: CB function to assert device wake (optional)
@@ -419,6 +420,7 @@ struct mhi_controller {
spinlock_t wlock;
struct mhi_link_info mhi_link_info;
struct work_struct st_worker;
+ struct workqueue_struct *hiprio_wq;
wait_queue_head_t state_event;
void (*status_cb)(struct mhi_controller *mhi_cntrl,
--
The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum,
a Linux Foundation Collaborative Project
^ permalink raw reply related [flat|nested] 13+ messages in thread* [PATCH v2 03/12] bus: mhi: core: Skip device wake in error or shutdown states
2020-10-30 1:51 [PATCH v2 00/12] Bug fixes and improvements for MHI power operations Bhaumik Bhatt
2020-10-30 1:51 ` [PATCH v2 01/12] bus: mhi: core: Use appropriate names for firmware load functions Bhaumik Bhatt
2020-10-30 1:51 ` [PATCH v2 02/12] bus: mhi: core: Move to using high priority workqueue Bhaumik Bhatt
@ 2020-10-30 1:51 ` Bhaumik Bhatt
2020-10-30 1:51 ` [PATCH v2 04/12] bus: mhi: core: Move to SYS_ERROR regardless of RDDM capability Bhaumik Bhatt
` (8 subsequent siblings)
11 siblings, 0 replies; 13+ messages in thread
From: Bhaumik Bhatt @ 2020-10-30 1:51 UTC (permalink / raw)
To: manivannan.sadhasivam
Cc: linux-arm-msm, hemantk, jhugo, linux-kernel, Bhaumik Bhatt
MHI client drivers can request a device wake even if the device
may be in an error state or undergoing a shutdown. To prevent
unnecessary device wake processing, check for the device state
and bail out early so that the clients are made aware of the
device state sooner.
Signed-off-by: Bhaumik Bhatt <bbhatt@codeaurora.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
---
drivers/bus/mhi/core/pm.c | 4 ++++
1 file changed, 4 insertions(+)
diff --git a/drivers/bus/mhi/core/pm.c b/drivers/bus/mhi/core/pm.c
index 805b6fa74..0299196 100644
--- a/drivers/bus/mhi/core/pm.c
+++ b/drivers/bus/mhi/core/pm.c
@@ -827,6 +827,10 @@ int __mhi_device_get_sync(struct mhi_controller *mhi_cntrl)
/* Wake up the device */
read_lock_bh(&mhi_cntrl->pm_lock);
+ if (MHI_PM_IN_ERROR_STATE(mhi_cntrl->pm_state)) {
+ read_unlock_bh(&mhi_cntrl->pm_lock);
+ return -EIO;
+ }
mhi_cntrl->wake_get(mhi_cntrl, true);
if (MHI_PM_IN_SUSPEND_STATE(mhi_cntrl->pm_state))
mhi_trigger_resume(mhi_cntrl);
--
The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum,
a Linux Foundation Collaborative Project
^ permalink raw reply related [flat|nested] 13+ messages in thread* [PATCH v2 04/12] bus: mhi: core: Move to SYS_ERROR regardless of RDDM capability
2020-10-30 1:51 [PATCH v2 00/12] Bug fixes and improvements for MHI power operations Bhaumik Bhatt
` (2 preceding siblings ...)
2020-10-30 1:51 ` [PATCH v2 03/12] bus: mhi: core: Skip device wake in error or shutdown states Bhaumik Bhatt
@ 2020-10-30 1:51 ` Bhaumik Bhatt
2020-10-30 1:51 ` [PATCH v2 05/12] bus: mhi: core: Prevent sending multiple RDDM entry callbacks Bhaumik Bhatt
` (7 subsequent siblings)
11 siblings, 0 replies; 13+ messages in thread
From: Bhaumik Bhatt @ 2020-10-30 1:51 UTC (permalink / raw)
To: manivannan.sadhasivam
Cc: linux-arm-msm, hemantk, jhugo, linux-kernel, Bhaumik Bhatt
In some cases, the entry of device to RDDM execution environment
can occur after a significant amount of time has elapsed and a
SYS_ERROR state change event has already arrived. This can result
in scenarios where MHI controller and client drivers are unaware
of the error state of the device. Remove the check for rddm_image
when processing the SYS_ERROR state change as it is present in
mhi_pm_sys_err_handler() already and prevent further activity
until the expected RDDM execution environment change occurs or
the controller driver decides further action.
Signed-off-by: Bhaumik Bhatt <bbhatt@codeaurora.org>
---
drivers/bus/mhi/core/main.c | 12 ++++--------
1 file changed, 4 insertions(+), 8 deletions(-)
diff --git a/drivers/bus/mhi/core/main.c b/drivers/bus/mhi/core/main.c
index 2cff5dd..1f32d67 100644
--- a/drivers/bus/mhi/core/main.c
+++ b/drivers/bus/mhi/core/main.c
@@ -733,19 +733,15 @@ int mhi_process_ctrl_ev_ring(struct mhi_controller *mhi_cntrl,
break;
case MHI_STATE_SYS_ERR:
{
- enum mhi_pm_state new_state;
-
- /* skip SYS_ERROR handling if RDDM supported */
- if (mhi_cntrl->ee == MHI_EE_RDDM ||
- mhi_cntrl->rddm_image)
- break;
+ enum mhi_pm_state state = MHI_PM_STATE_MAX;
dev_dbg(dev, "System error detected\n");
write_lock_irq(&mhi_cntrl->pm_lock);
- new_state = mhi_tryset_pm_state(mhi_cntrl,
+ if (mhi_cntrl->ee != MHI_EE_RDDM)
+ state = mhi_tryset_pm_state(mhi_cntrl,
MHI_PM_SYS_ERR_DETECT);
write_unlock_irq(&mhi_cntrl->pm_lock);
- if (new_state == MHI_PM_SYS_ERR_DETECT)
+ if (state == MHI_PM_SYS_ERR_DETECT)
mhi_pm_sys_err_handler(mhi_cntrl);
break;
}
--
The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum,
a Linux Foundation Collaborative Project
^ permalink raw reply related [flat|nested] 13+ messages in thread* [PATCH v2 05/12] bus: mhi: core: Prevent sending multiple RDDM entry callbacks
2020-10-30 1:51 [PATCH v2 00/12] Bug fixes and improvements for MHI power operations Bhaumik Bhatt
` (3 preceding siblings ...)
2020-10-30 1:51 ` [PATCH v2 04/12] bus: mhi: core: Move to SYS_ERROR regardless of RDDM capability Bhaumik Bhatt
@ 2020-10-30 1:51 ` Bhaumik Bhatt
2020-10-30 1:51 ` [PATCH v2 06/12] bus: mhi: core: Move to an error state on any firmware load failure Bhaumik Bhatt
` (6 subsequent siblings)
11 siblings, 0 replies; 13+ messages in thread
From: Bhaumik Bhatt @ 2020-10-30 1:51 UTC (permalink / raw)
To: manivannan.sadhasivam
Cc: linux-arm-msm, hemantk, jhugo, linux-kernel, Bhaumik Bhatt
If an mhi_power_down() is initiated after the device has entered
RDDM and a status callback was provided for it, it is possible
that another BHI interrupt fires while waiting for the MHI
RESET to be cleared. If that happens, MHI host would have moved
a "disabled" execution environment and the check to allow sending
an RDDM status callback will pass when it is should not. Add a
check to see if MHI is in an active state before proceeding.
Signed-off-by: Bhaumik Bhatt <bbhatt@codeaurora.org>
---
drivers/bus/mhi/core/main.c | 4 ++++
1 file changed, 4 insertions(+)
diff --git a/drivers/bus/mhi/core/main.c b/drivers/bus/mhi/core/main.c
index 1f32d67..172b48b 100644
--- a/drivers/bus/mhi/core/main.c
+++ b/drivers/bus/mhi/core/main.c
@@ -399,6 +399,10 @@ irqreturn_t mhi_intvec_threaded_handler(int irq_number, void *priv)
/* If device supports RDDM don't bother processing SYS error */
if (mhi_cntrl->rddm_image) {
+ /* host may be performing a device power down already */
+ if (!mhi_is_active(mhi_cntrl))
+ goto exit_intvec;
+
if (mhi_cntrl->ee == MHI_EE_RDDM && mhi_cntrl->ee != ee) {
mhi_cntrl->status_cb(mhi_cntrl, MHI_CB_EE_RDDM);
wake_up_all(&mhi_cntrl->state_event);
--
The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum,
a Linux Foundation Collaborative Project
^ permalink raw reply related [flat|nested] 13+ messages in thread* [PATCH v2 06/12] bus: mhi: core: Move to an error state on any firmware load failure
2020-10-30 1:51 [PATCH v2 00/12] Bug fixes and improvements for MHI power operations Bhaumik Bhatt
` (4 preceding siblings ...)
2020-10-30 1:51 ` [PATCH v2 05/12] bus: mhi: core: Prevent sending multiple RDDM entry callbacks Bhaumik Bhatt
@ 2020-10-30 1:51 ` Bhaumik Bhatt
2020-10-30 1:51 ` [PATCH v2 07/12] bus: mhi: core: Use appropriate label in firmware load handler API Bhaumik Bhatt
` (5 subsequent siblings)
11 siblings, 0 replies; 13+ messages in thread
From: Bhaumik Bhatt @ 2020-10-30 1:51 UTC (permalink / raw)
To: manivannan.sadhasivam
Cc: linux-arm-msm, hemantk, jhugo, linux-kernel, Bhaumik Bhatt
Move MHI to a firmware download error state for a failure to find
the firmware files or to load SBL or EBL image using BHI/BHIe. This
helps detect an error state sooner and shortens the wait for a
synchronous power up timeout.
Signed-off-by: Bhaumik Bhatt <bbhatt@codeaurora.org>
---
drivers/bus/mhi/core/boot.c | 35 ++++++++++++++++++++---------------
1 file changed, 20 insertions(+), 15 deletions(-)
diff --git a/drivers/bus/mhi/core/boot.c b/drivers/bus/mhi/core/boot.c
index 7d6b3a7..cec5010 100644
--- a/drivers/bus/mhi/core/boot.c
+++ b/drivers/bus/mhi/core/boot.c
@@ -425,13 +425,13 @@ void mhi_fw_load_handler(struct mhi_controller *mhi_cntrl)
!mhi_cntrl->seg_len))) {
dev_err(dev,
"No firmware image defined or !sbl_size || !seg_len\n");
- return;
+ goto error_fw_load;
}
ret = request_firmware(&firmware, fw_name, dev);
if (ret) {
dev_err(dev, "Error loading firmware: %d\n", ret);
- return;
+ goto error_fw_load;
}
size = (mhi_cntrl->fbc_download) ? mhi_cntrl->sbl_size : firmware->size;
@@ -443,7 +443,7 @@ void mhi_fw_load_handler(struct mhi_controller *mhi_cntrl)
buf = mhi_alloc_coherent(mhi_cntrl, size, &dma_addr, GFP_KERNEL);
if (!buf) {
release_firmware(firmware);
- return;
+ goto error_fw_load;
}
/* Download image using BHI */
@@ -451,17 +451,17 @@ void mhi_fw_load_handler(struct mhi_controller *mhi_cntrl)
ret = mhi_fw_load_bhi(mhi_cntrl, dma_addr, size);
mhi_free_coherent(mhi_cntrl, size, buf, dma_addr);
- if (!mhi_cntrl->fbc_download || ret || mhi_cntrl->ee == MHI_EE_EDL)
- release_firmware(firmware);
-
/* Error or in EDL mode, we're done */
if (ret) {
dev_err(dev, "MHI did not load image over BHI, ret: %d\n", ret);
- return;
+ release_firmware(firmware);
+ goto error_fw_load;
}
- if (mhi_cntrl->ee == MHI_EE_EDL)
+ if (mhi_cntrl->ee == MHI_EE_EDL) {
+ release_firmware(firmware);
return;
+ }
write_lock_irq(&mhi_cntrl->pm_lock);
mhi_cntrl->dev_state = MHI_STATE_RESET;
@@ -474,13 +474,17 @@ void mhi_fw_load_handler(struct mhi_controller *mhi_cntrl)
if (mhi_cntrl->fbc_download) {
ret = mhi_alloc_bhie_table(mhi_cntrl, &mhi_cntrl->fbc_image,
firmware->size);
- if (ret)
- goto error_alloc_fw_table;
+ if (ret) {
+ release_firmware(firmware);
+ goto error_fw_load;
+ }
/* Load the firmware into BHIE vec table */
mhi_firmware_copy(mhi_cntrl, firmware, mhi_cntrl->fbc_image);
}
+ release_firmware(firmware);
+
fw_load_ee_pthru:
/* Transitioning into MHI RESET->READY state */
ret = mhi_ready_state_transition(mhi_cntrl);
@@ -509,11 +513,11 @@ void mhi_fw_load_handler(struct mhi_controller *mhi_cntrl)
ret = mhi_fw_load_bhie(mhi_cntrl,
/* Vector table is the last entry */
&image_info->mhi_buf[image_info->entries - 1]);
- if (ret)
+ if (ret) {
dev_err(dev, "MHI did not load image over BHIe, ret: %d\n",
ret);
-
- release_firmware(firmware);
+ goto error_fw_load;
+ }
return;
@@ -521,6 +525,7 @@ void mhi_fw_load_handler(struct mhi_controller *mhi_cntrl)
mhi_free_bhie_table(mhi_cntrl, mhi_cntrl->fbc_image);
mhi_cntrl->fbc_image = NULL;
-error_alloc_fw_table:
- release_firmware(firmware);
+error_fw_load:
+ mhi_cntrl->pm_state = MHI_PM_FW_DL_ERR;
+ wake_up_all(&mhi_cntrl->state_event);
}
--
The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum,
a Linux Foundation Collaborative Project
^ permalink raw reply related [flat|nested] 13+ messages in thread* [PATCH v2 07/12] bus: mhi: core: Use appropriate label in firmware load handler API
2020-10-30 1:51 [PATCH v2 00/12] Bug fixes and improvements for MHI power operations Bhaumik Bhatt
` (5 preceding siblings ...)
2020-10-30 1:51 ` [PATCH v2 06/12] bus: mhi: core: Move to an error state on any firmware load failure Bhaumik Bhatt
@ 2020-10-30 1:51 ` Bhaumik Bhatt
2020-10-30 1:51 ` [PATCH v2 08/12] bus: mhi: core: Move to an error state on mission mode failure Bhaumik Bhatt
` (4 subsequent siblings)
11 siblings, 0 replies; 13+ messages in thread
From: Bhaumik Bhatt @ 2020-10-30 1:51 UTC (permalink / raw)
To: manivannan.sadhasivam
Cc: linux-arm-msm, hemantk, jhugo, linux-kernel, Bhaumik Bhatt
Correct the "error_read" label to say "error_ready_state" as that
is the appropriate usage of the label.
Signed-off-by: Bhaumik Bhatt <bbhatt@codeaurora.org>
---
drivers/bus/mhi/core/boot.c | 6 +++---
1 file changed, 3 insertions(+), 3 deletions(-)
diff --git a/drivers/bus/mhi/core/boot.c b/drivers/bus/mhi/core/boot.c
index cec5010..6b4c51e 100644
--- a/drivers/bus/mhi/core/boot.c
+++ b/drivers/bus/mhi/core/boot.c
@@ -494,7 +494,7 @@ void mhi_fw_load_handler(struct mhi_controller *mhi_cntrl)
if (ret) {
dev_err(dev, "MHI did not enter READY state\n");
- goto error_read;
+ goto error_ready_state;
}
/* Wait for the SBL event */
@@ -505,7 +505,7 @@ void mhi_fw_load_handler(struct mhi_controller *mhi_cntrl)
if (!ret || MHI_PM_IN_ERROR_STATE(mhi_cntrl->pm_state)) {
dev_err(dev, "MHI did not enter SBL\n");
- goto error_read;
+ goto error_ready_state;
}
/* Start full firmware image download */
@@ -521,7 +521,7 @@ void mhi_fw_load_handler(struct mhi_controller *mhi_cntrl)
return;
-error_read:
+error_ready_state:
mhi_free_bhie_table(mhi_cntrl, mhi_cntrl->fbc_image);
mhi_cntrl->fbc_image = NULL;
--
The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum,
a Linux Foundation Collaborative Project
^ permalink raw reply related [flat|nested] 13+ messages in thread* [PATCH v2 08/12] bus: mhi: core: Move to an error state on mission mode failure
2020-10-30 1:51 [PATCH v2 00/12] Bug fixes and improvements for MHI power operations Bhaumik Bhatt
` (6 preceding siblings ...)
2020-10-30 1:51 ` [PATCH v2 07/12] bus: mhi: core: Use appropriate label in firmware load handler API Bhaumik Bhatt
@ 2020-10-30 1:51 ` Bhaumik Bhatt
2020-10-30 1:52 ` [PATCH v2 09/12] bus: mhi: core: Check for IRQ availability during registration Bhaumik Bhatt
` (3 subsequent siblings)
11 siblings, 0 replies; 13+ messages in thread
From: Bhaumik Bhatt @ 2020-10-30 1:51 UTC (permalink / raw)
To: manivannan.sadhasivam
Cc: linux-arm-msm, hemantk, jhugo, linux-kernel, Bhaumik Bhatt
If the host receives a mission mode event and by the time it can get
to processing it, the register accesses fail implying a connectivity
error, MHI should move to an error state. This helps avoid longer wait
times from a synchronous power up perspective and accurately reflects
the MHI execution environment and power management states.
Signed-off-by: Bhaumik Bhatt <bbhatt@codeaurora.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
---
drivers/bus/mhi/core/pm.c | 8 ++++++--
1 file changed, 6 insertions(+), 2 deletions(-)
diff --git a/drivers/bus/mhi/core/pm.c b/drivers/bus/mhi/core/pm.c
index 0299196..06adea2 100644
--- a/drivers/bus/mhi/core/pm.c
+++ b/drivers/bus/mhi/core/pm.c
@@ -383,10 +383,14 @@ static int mhi_pm_mission_mode_transition(struct mhi_controller *mhi_cntrl)
write_lock_irq(&mhi_cntrl->pm_lock);
if (MHI_REG_ACCESS_VALID(mhi_cntrl->pm_state))
mhi_cntrl->ee = mhi_get_exec_env(mhi_cntrl);
- write_unlock_irq(&mhi_cntrl->pm_lock);
- if (!MHI_IN_MISSION_MODE(mhi_cntrl->ee))
+ if (!MHI_IN_MISSION_MODE(mhi_cntrl->ee)) {
+ mhi_cntrl->pm_state = MHI_PM_LD_ERR_FATAL_DETECT;
+ write_unlock_irq(&mhi_cntrl->pm_lock);
+ wake_up_all(&mhi_cntrl->state_event);
return -EIO;
+ }
+ write_unlock_irq(&mhi_cntrl->pm_lock);
wake_up_all(&mhi_cntrl->state_event);
--
The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum,
a Linux Foundation Collaborative Project
^ permalink raw reply related [flat|nested] 13+ messages in thread* [PATCH v2 09/12] bus: mhi: core: Check for IRQ availability during registration
2020-10-30 1:51 [PATCH v2 00/12] Bug fixes and improvements for MHI power operations Bhaumik Bhatt
` (7 preceding siblings ...)
2020-10-30 1:51 ` [PATCH v2 08/12] bus: mhi: core: Move to an error state on mission mode failure Bhaumik Bhatt
@ 2020-10-30 1:52 ` Bhaumik Bhatt
2020-10-30 1:52 ` [PATCH v2 10/12] bus: mhi: core: Separate system error and power down handling Bhaumik Bhatt
` (2 subsequent siblings)
11 siblings, 0 replies; 13+ messages in thread
From: Bhaumik Bhatt @ 2020-10-30 1:52 UTC (permalink / raw)
To: manivannan.sadhasivam
Cc: linux-arm-msm, hemantk, jhugo, linux-kernel, Bhaumik Bhatt
Current design allows a controller to register with MHI successfully
without the need to have any IRQs available for use. If no IRQs are
available, power up requests to MHI can fail after a successful
registration with MHI. Improve the design by checking for the number
of IRQs available sooner within the mhi_regsiter_controller() API as
it is required to be specified by the controller.
Signed-off-by: Bhaumik Bhatt <bbhatt@codeaurora.org>
---
drivers/bus/mhi/core/init.c | 2 +-
drivers/bus/mhi/core/pm.c | 3 ---
2 files changed, 1 insertion(+), 4 deletions(-)
diff --git a/drivers/bus/mhi/core/init.c b/drivers/bus/mhi/core/init.c
index 23b6dd6..5dd9e39 100644
--- a/drivers/bus/mhi/core/init.c
+++ b/drivers/bus/mhi/core/init.c
@@ -858,7 +858,7 @@ int mhi_register_controller(struct mhi_controller *mhi_cntrl,
if (!mhi_cntrl->runtime_get || !mhi_cntrl->runtime_put ||
!mhi_cntrl->status_cb || !mhi_cntrl->read_reg ||
- !mhi_cntrl->write_reg)
+ !mhi_cntrl->write_reg || !mhi_cntrl->nr_irqs)
return -EINVAL;
ret = parse_config(mhi_cntrl, config);
diff --git a/drivers/bus/mhi/core/pm.c b/drivers/bus/mhi/core/pm.c
index 06adea2..1d04e401 100644
--- a/drivers/bus/mhi/core/pm.c
+++ b/drivers/bus/mhi/core/pm.c
@@ -926,9 +926,6 @@ int mhi_async_power_up(struct mhi_controller *mhi_cntrl)
dev_info(dev, "Requested to power ON\n");
- if (mhi_cntrl->nr_irqs < 1)
- return -EINVAL;
-
/* Supply default wake routines if not provided by controller driver */
if (!mhi_cntrl->wake_get || !mhi_cntrl->wake_put ||
!mhi_cntrl->wake_toggle) {
--
The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum,
a Linux Foundation Collaborative Project
^ permalink raw reply related [flat|nested] 13+ messages in thread* [PATCH v2 10/12] bus: mhi: core: Separate system error and power down handling
2020-10-30 1:51 [PATCH v2 00/12] Bug fixes and improvements for MHI power operations Bhaumik Bhatt
` (8 preceding siblings ...)
2020-10-30 1:52 ` [PATCH v2 09/12] bus: mhi: core: Check for IRQ availability during registration Bhaumik Bhatt
@ 2020-10-30 1:52 ` Bhaumik Bhatt
2020-10-30 1:52 ` [PATCH v2 11/12] bus: mhi: core: Mark and maintain device states early on after power down Bhaumik Bhatt
2020-10-30 1:52 ` [PATCH v2 12/12] bus: mhi: core: Remove MHI event ring IRQ handlers when powering down Bhaumik Bhatt
11 siblings, 0 replies; 13+ messages in thread
From: Bhaumik Bhatt @ 2020-10-30 1:52 UTC (permalink / raw)
To: manivannan.sadhasivam
Cc: linux-arm-msm, hemantk, jhugo, linux-kernel, Bhaumik Bhatt
Currently, there exist a set of if...else statements in the
mhi_pm_disable_transition() function which make handling system
error and disable transitions differently complex. To make that
cleaner and facilitate differences in behavior, separate these
two transitions for MHI host.
Signed-off-by: Bhaumik Bhatt <bbhatt@codeaurora.org>
---
drivers/bus/mhi/core/pm.c | 159 +++++++++++++++++++++++++++++++++++++++-------
1 file changed, 137 insertions(+), 22 deletions(-)
diff --git a/drivers/bus/mhi/core/pm.c b/drivers/bus/mhi/core/pm.c
index 1d04e401..347ae7d 100644
--- a/drivers/bus/mhi/core/pm.c
+++ b/drivers/bus/mhi/core/pm.c
@@ -444,7 +444,7 @@ static int mhi_pm_mission_mode_transition(struct mhi_controller *mhi_cntrl)
return ret;
}
-/* Handle SYS_ERR and Shutdown transitions */
+/* Handle shutdown transitions */
static void mhi_pm_disable_transition(struct mhi_controller *mhi_cntrl,
enum mhi_pm_state transition_state)
{
@@ -460,10 +460,6 @@ static void mhi_pm_disable_transition(struct mhi_controller *mhi_cntrl,
to_mhi_pm_state_str(mhi_cntrl->pm_state),
to_mhi_pm_state_str(transition_state));
- /* We must notify MHI control driver so it can clean up first */
- if (transition_state == MHI_PM_SYS_ERR_PROCESS)
- mhi_cntrl->status_cb(mhi_cntrl, MHI_CB_SYS_ERROR);
-
mutex_lock(&mhi_cntrl->pm_mutex);
write_lock_irq(&mhi_cntrl->pm_lock);
prev_state = mhi_cntrl->pm_state;
@@ -502,11 +498,8 @@ static void mhi_pm_disable_transition(struct mhi_controller *mhi_cntrl,
MHICTRL_RESET_SHIFT,
&in_reset) ||
!in_reset, timeout);
- if ((!ret || in_reset) && cur_state == MHI_PM_SYS_ERR_PROCESS) {
+ if (!ret || in_reset)
dev_err(dev, "Device failed to exit MHI Reset state\n");
- mutex_unlock(&mhi_cntrl->pm_mutex);
- return;
- }
/*
* Device will clear BHI_INTVEC as a part of RESET processing,
@@ -566,19 +559,142 @@ static void mhi_pm_disable_transition(struct mhi_controller *mhi_cntrl,
er_ctxt->wp = er_ctxt->rbase;
}
- if (cur_state == MHI_PM_SYS_ERR_PROCESS) {
- mhi_ready_state_transition(mhi_cntrl);
- } else {
- /* Move to disable state */
- write_lock_irq(&mhi_cntrl->pm_lock);
- cur_state = mhi_tryset_pm_state(mhi_cntrl, MHI_PM_DISABLE);
- write_unlock_irq(&mhi_cntrl->pm_lock);
- if (unlikely(cur_state != MHI_PM_DISABLE))
- dev_err(dev, "Error moving from PM state: %s to: %s\n",
- to_mhi_pm_state_str(cur_state),
- to_mhi_pm_state_str(MHI_PM_DISABLE));
+ /* Move to disable state */
+ write_lock_irq(&mhi_cntrl->pm_lock);
+ cur_state = mhi_tryset_pm_state(mhi_cntrl, MHI_PM_DISABLE);
+ write_unlock_irq(&mhi_cntrl->pm_lock);
+ if (unlikely(cur_state != MHI_PM_DISABLE))
+ dev_err(dev, "Error moving from PM state: %s to: %s\n",
+ to_mhi_pm_state_str(cur_state),
+ to_mhi_pm_state_str(MHI_PM_DISABLE));
+
+ dev_dbg(dev, "Exiting with PM state: %s, MHI state: %s\n",
+ to_mhi_pm_state_str(mhi_cntrl->pm_state),
+ TO_MHI_STATE_STR(mhi_cntrl->dev_state));
+
+ mutex_unlock(&mhi_cntrl->pm_mutex);
+}
+
+/* Handle system error transitions */
+static void mhi_pm_sys_error_transition(struct mhi_controller *mhi_cntrl)
+{
+ enum mhi_pm_state cur_state, prev_state;
+ struct mhi_event *mhi_event;
+ struct mhi_cmd_ctxt *cmd_ctxt;
+ struct mhi_cmd *mhi_cmd;
+ struct mhi_event_ctxt *er_ctxt;
+ struct device *dev = &mhi_cntrl->mhi_dev->dev;
+ int ret, i;
+
+ dev_dbg(dev, "Transitioning from PM state: %s to: %s\n",
+ to_mhi_pm_state_str(mhi_cntrl->pm_state),
+ to_mhi_pm_state_str(MHI_PM_SYS_ERR_PROCESS));
+
+ /* We must notify MHI control driver so it can clean up first */
+ mhi_cntrl->status_cb(mhi_cntrl, MHI_CB_SYS_ERROR);
+
+ mutex_lock(&mhi_cntrl->pm_mutex);
+ write_lock_irq(&mhi_cntrl->pm_lock);
+ prev_state = mhi_cntrl->pm_state;
+ cur_state = mhi_tryset_pm_state(mhi_cntrl, MHI_PM_SYS_ERR_PROCESS);
+ write_unlock_irq(&mhi_cntrl->pm_lock);
+
+ if (cur_state != MHI_PM_SYS_ERR_PROCESS) {
+ dev_err(dev, "Failed to transition from PM state: %s to: %s\n",
+ to_mhi_pm_state_str(cur_state),
+ to_mhi_pm_state_str(MHI_PM_SYS_ERR_PROCESS));
+ goto exit_sys_error_transition;
+ }
+
+ mhi_cntrl->ee = MHI_EE_DISABLE_TRANSITION;
+ mhi_cntrl->dev_state = MHI_STATE_RESET;
+
+ /* Wake up threads waiting for state transition */
+ wake_up_all(&mhi_cntrl->state_event);
+
+ /* Trigger MHI RESET so that the device will not access host memory */
+ if (MHI_REG_ACCESS_VALID(prev_state)) {
+ u32 in_reset = -1;
+ unsigned long timeout = msecs_to_jiffies(mhi_cntrl->timeout_ms);
+
+ dev_dbg(dev, "Triggering MHI Reset in device\n");
+ mhi_set_mhi_state(mhi_cntrl, MHI_STATE_RESET);
+
+ /* Wait for the reset bit to be cleared by the device */
+ ret = wait_event_timeout(mhi_cntrl->state_event,
+ mhi_read_reg_field(mhi_cntrl,
+ mhi_cntrl->regs,
+ MHICTRL,
+ MHICTRL_RESET_MASK,
+ MHICTRL_RESET_SHIFT,
+ &in_reset) ||
+ !in_reset, timeout);
+ if (!ret || in_reset) {
+ dev_err(dev, "Device failed to exit MHI Reset state\n");
+ goto exit_sys_error_transition;
+ }
+
+ /*
+ * Device will clear BHI_INTVEC as a part of RESET processing,
+ * hence re-program it
+ */
+ mhi_write_reg(mhi_cntrl, mhi_cntrl->bhi, BHI_INTVEC, 0);
+ }
+
+ dev_dbg(dev,
+ "Waiting for all pending event ring processing to complete\n");
+ mhi_event = mhi_cntrl->mhi_event;
+ for (i = 0; i < mhi_cntrl->total_ev_rings; i++, mhi_event++) {
+ if (mhi_event->offload_ev)
+ continue;
+ tasklet_kill(&mhi_event->task);
}
+ /* Release lock and wait for all pending threads to complete */
+ mutex_unlock(&mhi_cntrl->pm_mutex);
+ dev_dbg(dev, "Waiting for all pending threads to complete\n");
+ wake_up_all(&mhi_cntrl->state_event);
+
+ dev_dbg(dev, "Reset all active channels and remove MHI devices\n");
+ device_for_each_child(mhi_cntrl->cntrl_dev, NULL, mhi_destroy_device);
+
+ mutex_lock(&mhi_cntrl->pm_mutex);
+
+ WARN_ON(atomic_read(&mhi_cntrl->dev_wake));
+ WARN_ON(atomic_read(&mhi_cntrl->pending_pkts));
+
+ /* Reset the ev rings and cmd rings */
+ dev_dbg(dev, "Resetting EV CTXT and CMD CTXT\n");
+ mhi_cmd = mhi_cntrl->mhi_cmd;
+ cmd_ctxt = mhi_cntrl->mhi_ctxt->cmd_ctxt;
+ for (i = 0; i < NR_OF_CMD_RINGS; i++, mhi_cmd++, cmd_ctxt++) {
+ struct mhi_ring *ring = &mhi_cmd->ring;
+
+ ring->rp = ring->base;
+ ring->wp = ring->base;
+ cmd_ctxt->rp = cmd_ctxt->rbase;
+ cmd_ctxt->wp = cmd_ctxt->rbase;
+ }
+
+ mhi_event = mhi_cntrl->mhi_event;
+ er_ctxt = mhi_cntrl->mhi_ctxt->er_ctxt;
+ for (i = 0; i < mhi_cntrl->total_ev_rings; i++, er_ctxt++,
+ mhi_event++) {
+ struct mhi_ring *ring = &mhi_event->ring;
+
+ /* Skip offload events */
+ if (mhi_event->offload_ev)
+ continue;
+
+ ring->rp = ring->base;
+ ring->wp = ring->base;
+ er_ctxt->rp = er_ctxt->rbase;
+ er_ctxt->wp = er_ctxt->rbase;
+ }
+
+ mhi_ready_state_transition(mhi_cntrl);
+
+exit_sys_error_transition:
dev_dbg(dev, "Exiting with PM state: %s, MHI state: %s\n",
to_mhi_pm_state_str(mhi_cntrl->pm_state),
TO_MHI_STATE_STR(mhi_cntrl->dev_state));
@@ -666,8 +782,7 @@ void mhi_pm_st_worker(struct work_struct *work)
mhi_ready_state_transition(mhi_cntrl);
break;
case DEV_ST_TRANSITION_SYS_ERR:
- mhi_pm_disable_transition
- (mhi_cntrl, MHI_PM_SYS_ERR_PROCESS);
+ mhi_pm_sys_error_transition(mhi_cntrl);
break;
case DEV_ST_TRANSITION_DISABLE:
mhi_pm_disable_transition
--
The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum,
a Linux Foundation Collaborative Project
^ permalink raw reply related [flat|nested] 13+ messages in thread* [PATCH v2 11/12] bus: mhi: core: Mark and maintain device states early on after power down
2020-10-30 1:51 [PATCH v2 00/12] Bug fixes and improvements for MHI power operations Bhaumik Bhatt
` (9 preceding siblings ...)
2020-10-30 1:52 ` [PATCH v2 10/12] bus: mhi: core: Separate system error and power down handling Bhaumik Bhatt
@ 2020-10-30 1:52 ` Bhaumik Bhatt
2020-10-30 1:52 ` [PATCH v2 12/12] bus: mhi: core: Remove MHI event ring IRQ handlers when powering down Bhaumik Bhatt
11 siblings, 0 replies; 13+ messages in thread
From: Bhaumik Bhatt @ 2020-10-30 1:52 UTC (permalink / raw)
To: manivannan.sadhasivam
Cc: linux-arm-msm, hemantk, jhugo, linux-kernel, Bhaumik Bhatt
mhi_power_down() does not ensure that the PM state is moved to an
inaccessible state soon enough as the system can encounter
scheduling delays till mhi_pm_disable_transition() gets called.
Additionally, if an MHI controller decides that the device is now
inaccessible and issues a power down, the register inaccessible
state is not maintained by moving from MHI_PM_LD_ERR_FATAL_DETECT
to MHI_PM_SHUTDOWN_PROCESS. This can result in bus errors if a
client driver attempted to read registers when powering down.
Close these gaps and avoid any race conditions to prevent such
activity.
Signed-off-by: Bhaumik Bhatt <bbhatt@codeaurora.org>
---
drivers/bus/mhi/core/pm.c | 77 ++++++++++++++++++++---------------------------
1 file changed, 33 insertions(+), 44 deletions(-)
diff --git a/drivers/bus/mhi/core/pm.c b/drivers/bus/mhi/core/pm.c
index 347ae7d..ffbf6f5 100644
--- a/drivers/bus/mhi/core/pm.c
+++ b/drivers/bus/mhi/core/pm.c
@@ -37,9 +37,10 @@
* M0 -> FW_DL_ERR
* M0 -> M3_ENTER -> M3 -> M3_EXIT --> M0
* L1: SYS_ERR_DETECT -> SYS_ERR_PROCESS --> POR
- * L2: SHUTDOWN_PROCESS -> DISABLE
+ * L2: SHUTDOWN_PROCESS -> LD_ERR_FATAL_DETECT
+ * SHUTDOWN_PROCESS -> DISABLE
* L3: LD_ERR_FATAL_DETECT <--> LD_ERR_FATAL_DETECT
- * LD_ERR_FATAL_DETECT -> SHUTDOWN_PROCESS
+ * LD_ERR_FATAL_DETECT -> DISABLE
*/
static struct mhi_pm_transitions const dev_state_transitions[] = {
/* L0 States */
@@ -72,7 +73,7 @@ static struct mhi_pm_transitions const dev_state_transitions[] = {
{
MHI_PM_M3,
MHI_PM_M3_EXIT | MHI_PM_SYS_ERR_DETECT |
- MHI_PM_SHUTDOWN_PROCESS | MHI_PM_LD_ERR_FATAL_DETECT
+ MHI_PM_LD_ERR_FATAL_DETECT
},
{
MHI_PM_M3_EXIT,
@@ -103,7 +104,7 @@ static struct mhi_pm_transitions const dev_state_transitions[] = {
/* L3 States */
{
MHI_PM_LD_ERR_FATAL_DETECT,
- MHI_PM_LD_ERR_FATAL_DETECT | MHI_PM_SHUTDOWN_PROCESS
+ MHI_PM_LD_ERR_FATAL_DETECT | MHI_PM_DISABLE
},
};
@@ -445,10 +446,9 @@ static int mhi_pm_mission_mode_transition(struct mhi_controller *mhi_cntrl)
}
/* Handle shutdown transitions */
-static void mhi_pm_disable_transition(struct mhi_controller *mhi_cntrl,
- enum mhi_pm_state transition_state)
+static void mhi_pm_disable_transition(struct mhi_controller *mhi_cntrl)
{
- enum mhi_pm_state cur_state, prev_state;
+ enum mhi_pm_state cur_state;
struct mhi_event *mhi_event;
struct mhi_cmd_ctxt *cmd_ctxt;
struct mhi_cmd *mhi_cmd;
@@ -456,33 +456,13 @@ static void mhi_pm_disable_transition(struct mhi_controller *mhi_cntrl,
struct device *dev = &mhi_cntrl->mhi_dev->dev;
int ret, i;
- dev_dbg(dev, "Transitioning from PM state: %s to: %s\n",
- to_mhi_pm_state_str(mhi_cntrl->pm_state),
- to_mhi_pm_state_str(transition_state));
+ dev_dbg(dev, "Processing disable transition with PM state: %s\n",
+ to_mhi_pm_state_str(mhi_cntrl->pm_state));
mutex_lock(&mhi_cntrl->pm_mutex);
- write_lock_irq(&mhi_cntrl->pm_lock);
- prev_state = mhi_cntrl->pm_state;
- cur_state = mhi_tryset_pm_state(mhi_cntrl, transition_state);
- if (cur_state == transition_state) {
- mhi_cntrl->ee = MHI_EE_DISABLE_TRANSITION;
- mhi_cntrl->dev_state = MHI_STATE_RESET;
- }
- write_unlock_irq(&mhi_cntrl->pm_lock);
-
- /* Wake up threads waiting for state transition */
- wake_up_all(&mhi_cntrl->state_event);
-
- if (cur_state != transition_state) {
- dev_err(dev, "Failed to transition to state: %s from: %s\n",
- to_mhi_pm_state_str(transition_state),
- to_mhi_pm_state_str(cur_state));
- mutex_unlock(&mhi_cntrl->pm_mutex);
- return;
- }
/* Trigger MHI RESET so that the device will not access host memory */
- if (MHI_REG_ACCESS_VALID(prev_state)) {
+ if (!MHI_PM_IN_FATAL_STATE(mhi_cntrl->pm_state)) {
u32 in_reset = -1;
unsigned long timeout = msecs_to_jiffies(mhi_cntrl->timeout_ms);
@@ -785,8 +765,7 @@ void mhi_pm_st_worker(struct work_struct *work)
mhi_pm_sys_error_transition(mhi_cntrl);
break;
case DEV_ST_TRANSITION_DISABLE:
- mhi_pm_disable_transition
- (mhi_cntrl, MHI_PM_SHUTDOWN_PROCESS);
+ mhi_pm_disable_transition(mhi_cntrl);
break;
default:
break;
@@ -1153,23 +1132,33 @@ EXPORT_SYMBOL_GPL(mhi_async_power_up);
void mhi_power_down(struct mhi_controller *mhi_cntrl, bool graceful)
{
- enum mhi_pm_state cur_state;
+ enum mhi_pm_state cur_state, transition_state;
struct device *dev = &mhi_cntrl->mhi_dev->dev;
/* If it's not a graceful shutdown, force MHI to linkdown state */
- if (!graceful) {
- mutex_lock(&mhi_cntrl->pm_mutex);
- write_lock_irq(&mhi_cntrl->pm_lock);
- cur_state = mhi_tryset_pm_state(mhi_cntrl,
- MHI_PM_LD_ERR_FATAL_DETECT);
- write_unlock_irq(&mhi_cntrl->pm_lock);
- mutex_unlock(&mhi_cntrl->pm_mutex);
- if (cur_state != MHI_PM_LD_ERR_FATAL_DETECT)
- dev_dbg(dev, "Failed to move to state: %s from: %s\n",
- to_mhi_pm_state_str(MHI_PM_LD_ERR_FATAL_DETECT),
- to_mhi_pm_state_str(mhi_cntrl->pm_state));
+ transition_state = (graceful) ? MHI_PM_SHUTDOWN_PROCESS :
+ MHI_PM_LD_ERR_FATAL_DETECT;
+
+ mutex_lock(&mhi_cntrl->pm_mutex);
+ write_lock_irq(&mhi_cntrl->pm_lock);
+ cur_state = mhi_tryset_pm_state(mhi_cntrl, transition_state);
+ if (cur_state != transition_state) {
+ dev_err(dev, "Failed to move to state: %s from: %s\n",
+ to_mhi_pm_state_str(transition_state),
+ to_mhi_pm_state_str(mhi_cntrl->pm_state));
+ /* Force link down or error fatal detected state */
+ mhi_cntrl->pm_state = MHI_PM_LD_ERR_FATAL_DETECT;
}
+ /* mark device inactive to avoid any further host processing */
+ mhi_cntrl->ee = MHI_EE_DISABLE_TRANSITION;
+ mhi_cntrl->dev_state = MHI_STATE_RESET;
+
+ wake_up_all(&mhi_cntrl->state_event);
+
+ write_unlock_irq(&mhi_cntrl->pm_lock);
+ mutex_unlock(&mhi_cntrl->pm_mutex);
+
mhi_queue_state_transition(mhi_cntrl, DEV_ST_TRANSITION_DISABLE);
/* Wait for shutdown to complete */
--
The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum,
a Linux Foundation Collaborative Project
^ permalink raw reply related [flat|nested] 13+ messages in thread* [PATCH v2 12/12] bus: mhi: core: Remove MHI event ring IRQ handlers when powering down
2020-10-30 1:51 [PATCH v2 00/12] Bug fixes and improvements for MHI power operations Bhaumik Bhatt
` (10 preceding siblings ...)
2020-10-30 1:52 ` [PATCH v2 11/12] bus: mhi: core: Mark and maintain device states early on after power down Bhaumik Bhatt
@ 2020-10-30 1:52 ` Bhaumik Bhatt
11 siblings, 0 replies; 13+ messages in thread
From: Bhaumik Bhatt @ 2020-10-30 1:52 UTC (permalink / raw)
To: manivannan.sadhasivam
Cc: linux-arm-msm, hemantk, jhugo, linux-kernel, Bhaumik Bhatt
While powering down, the device may or may not acknowledge an MHI
RESET issued by host for a graceful shutdown scenario and end up
sending an incoming data packet after tasklets have been killed.
If a rogue device sends this interrupt for a data transfer event
ring update, it can result in a tasklet getting scheduled while a
clean up is ongoing or has completed and cause access to freed
memory leading to a NULL pointer exception. Remove the interrupt
handlers for MHI event rings early on to avoid this scenario.
Signed-off-by: Bhaumik Bhatt <bbhatt@codeaurora.org>
---
drivers/bus/mhi/core/pm.c | 3 ++-
1 file changed, 2 insertions(+), 1 deletion(-)
diff --git a/drivers/bus/mhi/core/pm.c b/drivers/bus/mhi/core/pm.c
index ffbf6f5..28e2b87 100644
--- a/drivers/bus/mhi/core/pm.c
+++ b/drivers/bus/mhi/core/pm.c
@@ -627,6 +627,7 @@ static void mhi_pm_sys_error_transition(struct mhi_controller *mhi_cntrl)
for (i = 0; i < mhi_cntrl->total_ev_rings; i++, mhi_event++) {
if (mhi_event->offload_ev)
continue;
+ free_irq(mhi_cntrl->irq[mhi_event->irq], mhi_event);
tasklet_kill(&mhi_event->task);
}
@@ -1164,7 +1165,7 @@ void mhi_power_down(struct mhi_controller *mhi_cntrl, bool graceful)
/* Wait for shutdown to complete */
flush_work(&mhi_cntrl->st_worker);
- mhi_deinit_free_irq(mhi_cntrl);
+ free_irq(mhi_cntrl->irq[0], mhi_cntrl);
if (!mhi_cntrl->pre_init) {
/* Free all allocated resources */
--
The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum,
a Linux Foundation Collaborative Project
^ permalink raw reply related [flat|nested] 13+ messages in thread