Re: [PATCH v6 2/8] spi: rockchip-sfc: add rockchip serial flash controller

Chris Morgan
2021-06-09T16:57:37Z

On Wed, Jun 09, 2021 at 09:48:50PM +0800, Jon Lin wrote:
>
> On 6/9/21 10:36 AM, Chris Morgan wrote:
> > On Tue, Jun 08, 2021 at 10:26:38AM +0800, Jon Lin wrote:
> > > From: Chris Morgan <macromorgan@hotmail.com>
> > >
> > > Add the rockchip serial flash controller (SFC) driver.
> > >
> > > Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
> > > Signed-off-by: Jon Lin <jon.lin@rock-chips.com>
> > I think I hit "reply" earlier when I meant to hit "reply-all". Whoops.
> >
> > I wanted to say that for now this driver is not working for me on the
> > v3 hardware. There appears to be something wrong with alternating
> > between page programs and erase. I can consistently reproduce this by
> > writing a 4MB image of random data to my SPI flash chip at offset
> > c00000 using dd to mtdblock0. I've dumped the contents of what is
> > written to the controller and it appears at some point it goes from
> > doing a page program (02) to a dual io read (bb) to a sector erase
> > (20), then it repeatedly reads the status register (05) and I assume
> > the register never changes. As a result it just keeps looping over
> > the status register then eventually times out. I'm still debugging
> > to try and figure out exactly what is going on though.
> >
> > I also noticed that reading does not work consistently using dd
> > from the mtd0 device, however I have a proposed fix for that which
> > I list below at the appropriate section.
> >
> Can you enable dev_dbg in rockchip_sfc_xfer_setup, then send me log.

I can confirm that on the v7 patch I still get some "weirdness" when
I use mtdblock, but when I use flashrom things work entirely as
expected. I will still send you a log, but at this point I wonder if
it's related to an mtdblock issue rather than an issue with this
driver. In retrospect I don't recall testing things this extensively
earlier.

You can reproduce the issue by doing the following:

Create a random 4MB file (dd if=/dev/urandom of=rand.img bs=4M count=1)

Write the 4MB random file to the device using MTD Block drivers
(dd if=rand.img of=/dev/mtdblock0 bs=4096 seek=3072)

Read back the data (dd if=/dev/mtd0 of=rand1.img bs=4096 skip=3072)

Compare checksums (md5sum *.img)
When I do this I get different checksums for the random files. However
when I use flashrom to write instead of MTD Block, it works.

Read the ROM - I can confirm after extensive testing reads seem to work
just fine (dd if=/dev/mtd0 of=rom.img bs=8192)

Copy the random data to the image file
(dd if=rand.img of=rom.img bs=4096 seek=3072)

Flash the file with flashrom (flashrom -p linux_mtd -w rom.img)

Read back the random data
(dd if=/dev/mtd0 of=rand1.img bs=4096 skip=3072)

Compare checksums (md5sum *.img)
At this point the rand.img and rand1.img files have identical
checksums.

As for testing the reading bugs I found on v6 and below, it was a
matter of reading with dd using a block size bigger than the max_iosize
value, but with the addition of the adjust_op_size that seems to be
resolved now completely.

Test case:
Read flash image with varying block sizes
(dd if=/dev/mtd0 of=test1.img bs=4096)
(dd if=/dev/mtd0 of=test2.img bs=8192)
(dd if=/dev/mtd0 of=test3.img bs=16384)

Compare checksums (md5sum *.img)

Prior to v7 the checksum for test3.img would be different than the
other two. v7 now returns the same checksum for all 3 files.

>
> I successfully mount and test spinor jffs2 to confirm read/write/erase work
> work. I'll try more cases further.
>
> > > ---
> > >
> > > Changes in v6: None
> > > Changes in v5: None
> > > Changes in v4: None
> > > Changes in v3: None
> > > Changes in v2: None
> > > Changes in v1: None
> > >
> > > drivers/spi/Kconfig | 9 +
> > > drivers/spi/Makefile | 1 +
> > > drivers/spi/spi-rockchip-sfc.c | 660 +++++++++++++++++++++++++++++++++
> > > 3 files changed, 670 insertions(+)
> > > create mode 100644 drivers/spi/spi-rockchip-sfc.c
> > >
> > > diff --git a/drivers/spi/Kconfig b/drivers/spi/Kconfig
> > > index e71a4c514f7b..d89e5f3c9107 100644
> > > --- a/drivers/spi/Kconfig
> > > +++ b/drivers/spi/Kconfig
> > > @@ -658,6 +658,15 @@ config SPI_ROCKCHIP
> > > The main usecase of this controller is to use spi flash as boot
> > > device.
> > > +config SPI_ROCKCHIP_SFC
> > > + tristate "Rockchip Serial Flash Controller (SFC)"
> > > + depends on ARCH_ROCKCHIP || COMPILE_TEST
> > > + depends on HAS_IOMEM && HAS_DMA
> > > + help
> > > + This enables support for Rockchip serial flash controller. This
> > > + is a specialized controller used to access SPI flash on some
> > > + Rockchip SOCs.
> > > +
> > > config SPI_RB4XX
> > > tristate "Mikrotik RB4XX SPI master"
> > > depends on SPI_MASTER && ATH79
> > > diff --git a/drivers/spi/Makefile b/drivers/spi/Makefile
> > > index 13e54c45e9df..699db95c8441 100644
> > > --- a/drivers/spi/Makefile
> > > +++ b/drivers/spi/Makefile
> > > @@ -95,6 +95,7 @@ obj-$(CONFIG_SPI_QCOM_GENI) += spi-geni-qcom.o
> > > obj-$(CONFIG_SPI_QCOM_QSPI) += spi-qcom-qspi.o
> > > obj-$(CONFIG_SPI_QUP) += spi-qup.o
> > > obj-$(CONFIG_SPI_ROCKCHIP) += spi-rockchip.o
> > > +obj-$(CONFIG_SPI_ROCKCHIP_SFC) += spi-rockchip-sfc.o
> > > obj-$(CONFIG_SPI_RB4XX) += spi-rb4xx.o
> > > obj-$(CONFIG_MACH_REALTEK_RTL) += spi-realtek-rtl.o
> > > obj-$(CONFIG_SPI_RPCIF) += spi-rpc-if.o
> > > diff --git a/drivers/spi/spi-rockchip-sfc.c b/drivers/spi/spi-rockchip-sfc.c
> > > new file mode 100644
> > > index 000000000000..ec25ad278096
> > > --- /dev/null
> > > +++ b/drivers/spi/spi-rockchip-sfc.c
> > > @@ -0,0 +1,660 @@
> > > +// SPDX-License-Identifier: GPL-2.0-only
> > > +/*
> > > + * Rockchip Serial Flash Controller Driver
> > > + *
> > > + * Copyright (c) 2017-2021, Rockchip Inc.
> > > + * Author: Shawn Lin <shawn.lin@rock-chips.com>
> > > + * Chris Morgan <macroalpha82@gmail.com>
> > > + * Jon Lin <Jon.lin@rock-chips.com>
> > > + */
> > > +
> > > +#include <linux/bitops.h>
> > > +#include <linux/clk.h>
> > > +#include <linux/completion.h>
> > > +#include <linux/dma-mapping.h>
> > > +#include <linux/iopoll.h>
> > > +#include <linux/mm.h>
> > > +#include <linux/module.h>
> > > +#include <linux/of.h>
> > > +#include <linux/platform_device.h>
> > > +#include <linux/slab.h>
> > > +#include <linux/interrupt.h>
> > > +#include <linux/spi/spi-mem.h>
> > > +
> > > +/* System control */
> > > +#define SFC_CTRL 0x0
> > > +#define SFC_CTRL_PHASE_SEL_NEGETIVE BIT(1)
> > > +#define SFC_CTRL_CMD_BITS_SHIFT 8
> > > +#define SFC_CTRL_ADDR_BITS_SHIFT 10
> > > +#define SFC_CTRL_DATA_BITS_SHIFT 12
> > > +
> > > +/* Interrupt mask */
> > > +#define SFC_IMR 0x4
> > > +#define SFC_IMR_RX_FULL BIT(0)
> > > +#define SFC_IMR_RX_UFLOW BIT(1)
> > > +#define SFC_IMR_TX_OFLOW BIT(2)
> > > +#define SFC_IMR_TX_EMPTY BIT(3)
> > > +#define SFC_IMR_TRAN_FINISH BIT(4)
> > > +#define SFC_IMR_BUS_ERR BIT(5)
> > > +#define SFC_IMR_NSPI_ERR BIT(6)
> > > +#define SFC_IMR_DMA BIT(7)
> > > +
> > > +/* Interrupt clear */
> > > +#define SFC_ICLR 0x8
> > > +#define SFC_ICLR_RX_FULL BIT(0)
> > > +#define SFC_ICLR_RX_UFLOW BIT(1)
> > > +#define SFC_ICLR_TX_OFLOW BIT(2)
> > > +#define SFC_ICLR_TX_EMPTY BIT(3)
> > > +#define SFC_ICLR_TRAN_FINISH BIT(4)
> > > +#define SFC_ICLR_BUS_ERR BIT(5)
> > > +#define SFC_ICLR_NSPI_ERR BIT(6)
> > > +#define SFC_ICLR_DMA BIT(7)
> > > +
> > > +/* FIFO threshold level */
> > > +#define SFC_FTLR 0xc
> > > +#define SFC_FTLR_TX_SHIFT 0
> > > +#define SFC_FTLR_TX_MASK 0x1f
> > > +#define SFC_FTLR_RX_SHIFT 8
> > > +#define SFC_FTLR_RX_MASK 0x1f
> > > +
> > > +/* Reset FSM and FIFO */
> > > +#define SFC_RCVR 0x10
> > > +#define SFC_RCVR_RESET BIT(0)
> > > +
> > > +/* Enhanced mode */
> > > +#define SFC_AX 0x14
> > > +
> > > +/* Address Bit number */
> > > +#define SFC_ABIT 0x18
> > > +
> > > +/* Interrupt status */
> > > +#define SFC_ISR 0x1c
> > > +#define SFC_ISR_RX_FULL_SHIFT BIT(0)
> > > +#define SFC_ISR_RX_UFLOW_SHIFT BIT(1)
> > > +#define SFC_ISR_TX_OFLOW_SHIFT BIT(2)
> > > +#define SFC_ISR_TX_EMPTY_SHIFT BIT(3)
> > > +#define SFC_ISR_TX_FINISH_SHIFT BIT(4)
> > > +#define SFC_ISR_BUS_ERR_SHIFT BIT(5)
> > > +#define SFC_ISR_NSPI_ERR_SHIFT BIT(6)
> > > +#define SFC_ISR_DMA_SHIFT BIT(7)
> > > +
> > > +/* FIFO status */
> > > +#define SFC_FSR 0x20
> > > +#define SFC_FSR_TX_IS_FULL BIT(0)
> > > +#define SFC_FSR_TX_IS_EMPTY BIT(1)
> > > +#define SFC_FSR_RX_IS_EMPTY BIT(2)
> > > +#define SFC_FSR_RX_IS_FULL BIT(3)
> > > +#define SFC_FSR_TXLV_MASK GENMASK(12, 8)
> > > +#define SFC_FSR_TXLV_SHIFT 8
> > > +#define SFC_FSR_RXLV_MASK GENMASK(20, 16)
> > > +#define SFC_FSR_RXLV_SHIFT 16
> > > +
> > > +/* FSM status */
> > > +#define SFC_SR 0x24
> > > +#define SFC_SR_IS_IDLE 0x0
> > > +#define SFC_SR_IS_BUSY 0x1
> > > +
> > > +/* Raw interrupt status */
> > > +#define SFC_RISR 0x28
> > > +#define SFC_RISR_RX_FULL BIT(0)
> > > +#define SFC_RISR_RX_UNDERFLOW BIT(1)
> > > +#define SFC_RISR_TX_OVERFLOW BIT(2)
> > > +#define SFC_RISR_TX_EMPTY BIT(3)
> > > +#define SFC_RISR_TRAN_FINISH BIT(4)
> > > +#define SFC_RISR_BUS_ERR BIT(5)
> > > +#define SFC_RISR_NSPI_ERR BIT(6)
> > > +#define SFC_RISR_DMA BIT(7)
> > > +
> > > +/* Version */
> > > +#define SFC_VER 0x2C
> > > +#define SFC_VER_3 0x3
> > > +#define SFC_VER_4 0x4
> > > +#define SFC_VER_5 0x5
> > > +
> > > +/* Master trigger */
> > > +#define SFC_DMA_TRIGGER 0x80
> > > +
> > > +/* Src or Dst addr for master */
> > > +#define SFC_DMA_ADDR 0x84
> > > +
> > > +/* Length control register extension 32GB */
> > > +#define SFC_LEN_CTRL 0x88
> > > +#define SFC_LEN_CTRL_TRB_SEL 1
> > > +#define SFC_LEN_EXT 0x8C
> > > +
> > > +/* Command */
> > > +#define SFC_CMD 0x100
> > > +#define SFC_CMD_IDX_SHIFT 0
> > > +#define SFC_CMD_DUMMY_SHIFT 8
> > > +#define SFC_CMD_DIR_SHIFT 12
> > > +#define SFC_CMD_DIR_RD 0
> > > +#define SFC_CMD_DIR_WR 1
> > > +#define SFC_CMD_ADDR_SHIFT 14
> > > +#define SFC_CMD_ADDR_0BITS 0
> > > +#define SFC_CMD_ADDR_24BITS 1
> > > +#define SFC_CMD_ADDR_32BITS 2
> > > +#define SFC_CMD_ADDR_XBITS 3
> > > +#define SFC_CMD_TRAN_BYTES_SHIFT 16
> > > +#define SFC_CMD_CS_SHIFT 30
> > > +
> > > +/* Address */
> > > +#define SFC_ADDR 0x104
> > > +
> > > +/* Data */
> > > +#define SFC_DATA 0x108
> > > +
> > > +/* The controller and documentation reports that it supports up to 4 CS
> > > + * devices (0-3), however I have only been able to test a single CS (CS 0)
> > > + * due to the configuration of my device.
> > > + */
> > > +#define SFC_MAX_CHIPSELECT_NUM 4
> > > +
> > > +/* The SFC can transfer max 16KB - 1 at one time
> > > + * we set it to 15.5KB here for alignment.
> > > + */
> > > +#define SFC_MAX_IOSIZE_VER3 (512 * 31)
> > > +
> > > +#define SFC_MAX_IOSIZE_VER4 (0xFFFFFFFF)
> > > +
> > > +/* DMA is only enabled for large data transmission */
> > > +#define SFC_DMA_TRANS_THRETHOLD (0x40)
> > > +
> > > +/* Maximum clock values from datasheet suggest keeping clock value under
> > > + * 150MHz. No minimum or average value is suggested, but the U-boot BSP driver
> > > + * has a minimum of 10MHz and a default of 80MHz which seems reasonable.
> > > + */
> > > +#define SFC_MIN_SPEED_HZ (10 * 1000 * 1000)
> > > +#define SFC_DEFAULT_SPEED_HZ (80 * 1000 * 1000)
> > > +#define SFC_MAX_SPEED_HZ (150 * 1000 * 1000)
> > > +
> > > +struct rockchip_sfc {
> > > + struct device *dev;
> > > + void __iomem *regbase;
> > > + struct clk *hclk;
> > > + struct clk *clk;
> > > + u32 frequency;
> > > + /* virtual mapped addr for dma_buffer */
> > > + void *buffer;
> > > + dma_addr_t dma_buffer;
> > > + struct completion cp;
> > > + bool use_dma;
> > > + u32 max_iosize;
> > > +};
> > > +
> > > +static int rockchip_sfc_reset(struct rockchip_sfc *sfc)
> > > +{
> > > + int err;
> > > + u32 status;
> > > +
> > > + writel_relaxed(SFC_RCVR_RESET, sfc->regbase + SFC_RCVR);
> > > +
> > > + err = readl_poll_timeout(sfc->regbase + SFC_RCVR, status,
> > > + !(status & SFC_RCVR_RESET), 20,
> > > + jiffies_to_usecs(HZ));
> > > + if (err)
> > > + dev_err(sfc->dev, "SFC reset never finished\n");
> > > +
> > > + /* Still need to clear the masked interrupt from RISR */
> > > + writel_relaxed(0xFFFFFFFF, sfc->regbase + SFC_ICLR);
> > > +
> > > + dev_dbg(sfc->dev, "reset\n");
> > > +
> > > + return err;
> > > +}
> > > +
> > > +static u16 rockchip_sfc_get_version(struct rockchip_sfc *sfc)
> > > +{
> > > + return (u16)(readl(sfc->regbase + SFC_VER) & 0xffff);
> > > +}
> > > +
> > > +static u32 rockchip_sfc_get_max_iosize(struct rockchip_sfc *sfc)
> > > +{
> > > + if (rockchip_sfc_get_version(sfc) >= SFC_VER_4)
> > > + return SFC_MAX_IOSIZE_VER4;
> > > + else
> > > + return SFC_MAX_IOSIZE_VER3;
> > > +}
> > > +
> > > +static int rockchip_sfc_init(struct rockchip_sfc *sfc)
> > > +{
> > > + writel(0, sfc->regbase + SFC_CTRL);
> > > + if (rockchip_sfc_get_version(sfc) >= SFC_VER_4)
> > > + writel(SFC_LEN_CTRL_TRB_SEL, sfc->regbase + SFC_LEN_CTRL);
> > > +
> > > + return 0;
> > > +}
> > > +
> > > +static inline int rockchip_sfc_get_fifo_level(struct rockchip_sfc *sfc, int wr)
> > > +{
> > > + u32 fsr = readl_relaxed(sfc->regbase + SFC_FSR);
> > > + int level;
> > > +
> > > + if (wr)
> > > + level = (fsr & SFC_FSR_TXLV_MASK) >> SFC_FSR_TXLV_SHIFT;
> > > + else
> > > + level = (fsr & SFC_FSR_RXLV_MASK) >> SFC_FSR_RXLV_SHIFT;
> > > +
> > > + return level;
> > > +}
> > > +
> > > +static int rockchip_sfc_wait_fifo_ready(struct rockchip_sfc *sfc, int wr, u32 timeout)
> > > +{
> > > + unsigned long deadline = jiffies + timeout;
> > > + int level;
> > > +
> > > + while (!(level = rockchip_sfc_get_fifo_level(sfc, wr))) {
> > > + if (time_after_eq(jiffies, deadline)) {
> > > + dev_warn(sfc->dev, "%s fifo timeout\n", wr ? "write" : "read");
> > > + return -ETIMEDOUT;
> > > + }
> > > + udelay(1);
> > > + }
> > > +
> > > + return level;
> > > +}
> > > +
> > > +static int rockchip_sfc_xfer_setup(struct rockchip_sfc *sfc,
> > > + struct spi_mem *mem,
> > > + const struct spi_mem_op *op,
> > > + u32 len)
> > > +{
> > > + u32 ctrl = 0, cmd = 0;
> > > +
> > > + /* set CMD */
> > > + cmd = op->cmd.opcode;
> > > + ctrl |= ((op->cmd.buswidth >> 1) << SFC_CTRL_CMD_BITS_SHIFT);
> > > +
> > > + /* set ADDR */
> > > + if (op->addr.nbytes) {
> > > + if (op->addr.nbytes == 4) {
> > > + cmd |= SFC_CMD_ADDR_32BITS << SFC_CMD_ADDR_SHIFT;
> > > + } else if (op->addr.nbytes == 3) {
> > > + cmd |= SFC_CMD_ADDR_24BITS << SFC_CMD_ADDR_SHIFT;
> > > + } else {
> > > + cmd |= SFC_CMD_ADDR_XBITS << SFC_CMD_ADDR_SHIFT;
> > > + writel_relaxed(op->addr.nbytes * 8 - 1, sfc->regbase + SFC_ABIT);
> > > + }
> > > +
> > > + ctrl |= ((op->addr.buswidth >> 1) << SFC_CTRL_ADDR_BITS_SHIFT);
> > > + }
> > > +
> > > + /* set DUMMY */
> > > + if (op->dummy.nbytes) {
> > > + if (op->dummy.buswidth == 4)
> > > + cmd |= op->dummy.nbytes * 2 << SFC_CMD_DUMMY_SHIFT;
> > > + else if (op->dummy.buswidth == 2)
> > > + cmd |= op->dummy.nbytes * 4 << SFC_CMD_DUMMY_SHIFT;
> > > + else
> > > + cmd |= op->dummy.nbytes * 8 << SFC_CMD_DUMMY_SHIFT;
> > > + }
> > > +
> > I have no experience optimizing code or anything, but would it help
> > here to read the output of rockchip_sfc_get_version() to a variable
> > in the driver data, and then check that each time we hit this?
> > I don't know if there is any real-world difference in reading a
> > variable versus reading a register, so I'm just asking. It's not like
> > the sfc_version will change once the device is probed. :-)
>
> done.
>
> > > + /* set DATA */
> > > + if (rockchip_sfc_get_version(sfc) >= SFC_VER_4) /* Clear it if no data to transfer */
> > > + writel(len, sfc->regbase + SFC_LEN_EXT);
> > > + else
> > > + cmd |= len << SFC_CMD_TRAN_BYTES_SHIFT;
> > > + if (len) {
> > > + if (op->data.dir == SPI_MEM_DATA_OUT)
> > > + cmd |= SFC_CMD_DIR_WR << SFC_CMD_DIR_SHIFT;
> > > +
> > > + ctrl |= ((op->data.buswidth >> 1) << SFC_CTRL_DATA_BITS_SHIFT);
> > > + }
> > > + if (!len && op->addr.nbytes)
> > > + cmd |= SFC_CMD_DIR_WR << SFC_CMD_DIR_SHIFT;
> > > +
> > > + /* set the Controller */
> > > + ctrl |= SFC_CTRL_PHASE_SEL_NEGETIVE;
> > > + cmd |= mem->spi->chip_select << SFC_CMD_CS_SHIFT;
> > > +
> > > + dev_dbg(sfc->dev, "addr.nbytes=%x(x%d) dummy.nbytes=%x(x%d)\n",
> > > + op->addr.nbytes, op->addr.buswidth,
> > > + op->dummy.nbytes, op->dummy.buswidth);
> > > + dev_dbg(sfc->dev, "ctrl=%x cmd=%x addr=%llx len=%x\n",
> > > + ctrl, cmd, op->addr.val, len);
> > > +
> > > + writel(ctrl, sfc->regbase + SFC_CTRL);
> > > + writel(cmd, sfc->regbase + SFC_CMD);
> > > + if (op->addr.nbytes)
> > > + writel(op->addr.val, sfc->regbase + SFC_ADDR);
> > > +
> > > + return 0;
> > > +}
> > > +
> > > +static int rockchip_sfc_write_fifo(struct rockchip_sfc *sfc, const u8 *buf, int len)
> > > +{
> > > + u8 bytes = len & 0x3;
> > > + u32 dwords;
> > > + int tx_level;
> > > + u32 write_words;
> > > + u32 tmp = 0;
> > > +
> > > + dwords = len >> 2;
> > > + while (dwords) {
> > > + tx_level = rockchip_sfc_wait_fifo_ready(sfc, SFC_CMD_DIR_WR, HZ);
> > > + if (tx_level < 0)
> > > + return tx_level;
> > > + write_words = min_t(u32, tx_level, dwords);
> > > + iowrite32_rep(sfc->regbase + SFC_DATA, buf, write_words);
> > > + buf += write_words << 2;
> > > + dwords -= write_words;
> > > + }
> > > +
> > > + /* write the rest non word aligned bytes */
> > > + if (bytes) {
> > > + tx_level = rockchip_sfc_wait_fifo_ready(sfc, SFC_CMD_DIR_WR, HZ);
> > > + if (tx_level < 0)
> > > + return tx_level;
> > > + memcpy(&tmp, buf, bytes);
> > > + writel(tmp, sfc->regbase + SFC_DATA);
> > > + }
> > > +
> > > + return len;
> > > +}
> > > +
> > > +static int rockchip_sfc_read_fifo(struct rockchip_sfc *sfc, u8 *buf, int len)
> > > +{
> > > + u8 bytes = len & 0x3;
> > > + u32 dwords;
> > > + u8 read_words;
> > > + int rx_level;
> > > + int tmp;
> > > +
> > > + /* word aligned access only */
> > > + dwords = len >> 2;
> > > + while (dwords) {
> > > + rx_level = rockchip_sfc_wait_fifo_ready(sfc, SFC_CMD_DIR_RD, HZ);
> > > + if (rx_level < 0)
> > > + return rx_level;
> > > + read_words = min_t(u32, rx_level, dwords);
> > > + ioread32_rep(sfc->regbase + SFC_DATA, buf, read_words);
> > > + buf += read_words << 2;
> > > + dwords -= read_words;
> > > + }
> > > +
> > > + /* read the rest non word aligned bytes */
> > > + if (bytes) {
> > > + rx_level = rockchip_sfc_wait_fifo_ready(sfc, SFC_CMD_DIR_RD, HZ);
> > > + if (rx_level < 0)
> > > + return rx_level;
> > > + tmp = readl_relaxed(sfc->regbase + SFC_DATA);
> > > + memcpy(buf, &tmp, bytes);
> > > + }
> > > +
> > > + return len;
> > > +}
> > > +
> > > +static int rockchip_sfc_fifo_transfer_dma(struct rockchip_sfc *sfc, dma_addr_t dma_buf, size_t len)
> > > +{
> > > + u32 reg;
> > > + int err = 0;
> > > +
> > > + init_completion(&sfc->cp);
> > > +
> > > + writel(0xFFFFFFFF, sfc->regbase + SFC_ICLR);
> > > +
> > > + /* Enable transfer complete interrupt */
> > > + reg = readl(sfc->regbase + SFC_IMR);
> > > + reg &= ~SFC_IMR_DMA;
> > > + writel(reg, sfc->regbase + SFC_IMR);
> > > + writel((u32)dma_buf, sfc->regbase + SFC_DMA_ADDR);
> > > + writel(0x1, sfc->regbase + SFC_DMA_TRIGGER);
> > > +
> > > + /* Wait for the interrupt. */
> > > + if (!wait_for_completion_timeout(&sfc->cp, msecs_to_jiffies(2000))) {
> > > + dev_err(sfc->dev, "DMA wait for transfer finish timeout\n");
> > > + err = -ETIMEDOUT;
> > > + }
> > > +
> > > + writel(0xFFFFFFFF, sfc->regbase + SFC_ICLR);
> > > + /* Disable transfer finish interrupt */
> > > + reg = readl(sfc->regbase + SFC_IMR);
> > > + reg |= SFC_IMR_DMA;
> > > + writel(reg, sfc->regbase + SFC_IMR);
> > > +
> > > + return len;
> > > +}
> > > +
> > > +static int rockchip_sfc_xfer_data_poll(struct rockchip_sfc *sfc,
> > > + const struct spi_mem_op *op, u32 len)
> > > +{
> > > + dev_dbg(sfc->dev, "xfer_poll len=%x\n", len);
> > > +
> > > + if (op->data.dir == SPI_MEM_DATA_OUT)
> > > + return rockchip_sfc_write_fifo(sfc, op->data.buf.out, len);
> > > + else
> > > + return rockchip_sfc_read_fifo(sfc, op->data.buf.in, len);
> > > +}
> > > +
> > > +static int rockchip_sfc_xfer_data_dma(struct rockchip_sfc *sfc,
> > > + const struct spi_mem_op *op, u32 len)
> > > +{
> > > + int ret;
> > > +
> > > + dev_dbg(sfc->dev, "xfer_dma len=%x\n", len);
> > > +
> > > + if (op->data.dir == SPI_MEM_DATA_OUT) {
> > > + memcpy_toio(sfc->buffer, op->data.buf.out, len);
> > > + ret = rockchip_sfc_fifo_transfer_dma(sfc, sfc->dma_buffer, len);
> > > + } else {
> > > + ret = rockchip_sfc_fifo_transfer_dma(sfc, sfc->dma_buffer, len);
> > > + memcpy_fromio(op->data.buf.in, sfc->buffer, len);
> > > + }
> > > +
> > > + return ret;
> > > +}
> > > +
> > > +static int rockchip_sfc_xfer_done(struct rockchip_sfc *sfc, u32 timeout_us)
> > > +{
> > > + int ret = 0;
> > > + u32 status;
> > > +
> > > + ret = readl_poll_timeout(sfc->regbase + SFC_SR, status,
> > > + !(status & SFC_SR_IS_BUSY),
> > > + 20, timeout_us);
> > > + if (ret) {
> > > + dev_err(sfc->dev, "wait sfc idle timeout\n");
> > > + rockchip_sfc_reset(sfc);
> > > +
> > > + ret = -EIO;
> > > + }
> > > +
> > > + return ret;
> > > +}
> > > +
> > > +static int rockchip_sfc_exec_mem_op(struct spi_mem *mem, const struct spi_mem_op *op)
> > > +{
> > > + struct rockchip_sfc *sfc = spi_master_get_devdata(mem->spi->master);
> > > + u32 len = min_t(u32, op->data.nbytes, sfc->max_iosize);
> > Is it necessary to use the minimum of these 2 values if we use an
> > adjust_op_size which I propose below?
> it necessary if use adjust_op_size, done.
> > > + int ret;
> > > +
> > Again I'm asking this as someone with no experience optimizing code
> > or with compilers, but would it help to add an unlikely() here? It's
> > all but guaranteed the first time this code path is called the clock
> > will need to be set, but each subsequent call should not really have
> > to care since the clock likely won't be changing (as long as we're on
> > the same CS). We can also then set the sfc->frequency to what the
> > max_speed_hz was after successfully setting the rate so we can hit the
> > faster path after the first run (it looks like it's checking the
> > uninitalized value but never updating it after it's changed, so it's
> > always doing the clk_set_rate()).
> >
> > Also, should we clamp the clock speed between the min and max values?
> done.
> > > + if (mem->spi->max_speed_hz != sfc->frequency) {
> > > + if (clk_set_rate(sfc->clk, mem->spi->max_speed_hz))
> > > + return ret;
> > > + dev_dbg(sfc->dev, "set_freq=%dHz real_freq=%ldHz\n",
> > > + sfc->frequency, clk_get_rate(sfc->clk));
> > > + }
> > > +
> > > + rockchip_sfc_xfer_setup(sfc, mem, op, len);
> > > + if (len) {
> > > + if (likely(sfc->use_dma) && !(len & 0x3) && len >= SFC_DMA_TRANS_THRETHOLD)
> > > + ret = rockchip_sfc_xfer_data_dma(sfc, op, len);
> > > + else
> > > + ret = rockchip_sfc_xfer_data_poll(sfc, op, len);
> > > +
> > > + if (ret != len) {
> > > + dev_err(sfc->dev, "xfer data failed ret %d dir %d\n", ret, op->data.dir);
> > > +
> > > + return -EIO;
> > > + }
> > > + }
> > > +
> > > + return rockchip_sfc_xfer_done(sfc, 100000);
> > > +}
> > > +
> > I'll be honest with you, I had no idea if I needed this function or
> > not (the rockchip_sfc_get_name() function). I'm pretty sure it's not
> > needed though, so I assume it can be safely removed.
> >
> > > +static const char *rockchip_sfc_get_name(struct spi_mem *mem)
> > > +{
> > > + return devm_kasprintf(&mem->spi->dev, GFP_KERNEL, "%s.%d",
> > > + dev_name(&mem->spi->dev), mem->spi->chip_select);
> > > +}
> > > +
> > I had an issue with doing dd as mentioned above reading against mtd0,
> > and was able to fix it by adding a mem_op of adjust_op_size like this.
> > Not sure if it works for the v4/v5 hardware though.
> >
> > static int rockchip_sfc_adjust_op_size(struct spi_mem *mem, struct spi_mem_op *op)
> > {
> > struct rockchip_sfc *sfc = spi_master_get_devdata(mem->spi->master);
> >
> > op->data.nbytes = min(op->data.nbytes, sfc->max_iosize);
> > return 0;
> > }
>
> good idea.
>
> > > +static const struct spi_controller_mem_ops rockchip_sfc_mem_ops = {
> > > + .exec_op = rockchip_sfc_exec_mem_op,
> > > + .get_name = rockchip_sfc_get_name,
> > > +};
> > > +
> > > +static irqreturn_t rockchip_sfc_irq_handler(int irq, void *dev_id)
> > > +{
> > > + struct rockchip_sfc *sfc = dev_id;
> > > + u32 reg;
> > > +
> > > + reg = readl(sfc->regbase + SFC_RISR);
> > > +
> > > + /* Clear interrupt */
> > > + writel_relaxed(reg, sfc->regbase + SFC_ICLR);
> > > +
> > > + if (reg & SFC_RISR_DMA)
> > > + complete(&sfc->cp);
> > > +
> > >From a previous comment, we should only clear the interrupt if we
> > handle the specific one in question.
> >
> Compare with drivers/spi/spi-cadence-quadspi.c, I think the former code work
> well. Can explain more for the reason.
>
> > > + return IRQ_HANDLED;
> > > +}
> > > +
> > > +static int rockchip_sfc_probe(struct platform_device *pdev)
> > > +{
> > > + struct device *dev = &pdev->dev;
> > > + struct spi_master *master;
> > > + struct resource *res;
> > > + struct rockchip_sfc *sfc;
> > > + int ret;
> > > +
> > > + master = devm_spi_alloc_master(&pdev->dev, sizeof(*sfc));
> > > + if (!master)
> > > + return -ENOMEM;
> > > +
> > > + master->mem_ops = &rockchip_sfc_mem_ops;
> > > + master->dev.of_node = pdev->dev.of_node;
> > > + master->mode_bits = SPI_TX_QUAD | SPI_TX_DUAL | SPI_RX_QUAD | SPI_RX_DUAL;
> > > + master->min_speed_hz = SFC_MIN_SPEED_HZ;
> > > + master->max_speed_hz = SFC_MAX_SPEED_HZ;
> > > + master->num_chipselect = SFC_MAX_CHIPSELECT_NUM;
> > > +
> > > + sfc = spi_master_get_devdata(master);
> > > + sfc->dev = dev;
> > > +
> > > + res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
> > > + sfc->regbase = devm_ioremap_resource(dev, res);
> > > + if (IS_ERR(sfc->regbase))
> > > + return PTR_ERR(sfc->regbase);
> > > +
> > > + sfc->clk = devm_clk_get(&pdev->dev, "clk_sfc");
> > > + if (IS_ERR(sfc->clk)) {
> > > + dev_err(&pdev->dev, "Failed to get sfc interface clk\n");
> > > + return PTR_ERR(sfc->clk);
> > > + }
> > > +
> > > + sfc->hclk = devm_clk_get(&pdev->dev, "hclk_sfc");
> > > + if (IS_ERR(sfc->hclk)) {
> > > + dev_err(&pdev->dev, "Failed to get sfc ahb clk\n");
> > > + return PTR_ERR(sfc->hclk);
> > > + }
> > > +
> > > + sfc->use_dma = !of_property_read_bool(sfc->dev->of_node,
> > > + "rockchip,sfc-no-dma");
> > > +
> > > + if (sfc->use_dma) {
> > > + ret = dma_set_mask_and_coherent(dev, DMA_BIT_MASK(32));
> > > + if (ret) {
> > > + dev_warn(dev, "Unable to set dma mask\n");
> > > + return ret;
> > > + }
> > > +
> > > + sfc->buffer = dmam_alloc_coherent(dev, SFC_MAX_IOSIZE_VER3,
> > > + &sfc->dma_buffer,
> > > + GFP_KERNEL);
> > > + if (!sfc->buffer)
> > > + return -ENOMEM;
> > > + }
> > > +
> > > + ret = clk_prepare_enable(sfc->hclk);
> > > + if (ret) {
> > > + dev_err(&pdev->dev, "Failed to enable ahb clk\n");
> > > + goto err_hclk;
> > > + }
> > > +
> > > + ret = clk_prepare_enable(sfc->clk);
> > > + if (ret) {
> > > + dev_err(&pdev->dev, "Failed to enable interface clk\n");
> > > + goto err_clk;
> > > + }
> > > +
> > > + /* Find the irq */
> > > + ret = platform_get_irq(pdev, 0);
> > > + if (ret < 0) {
> > > + dev_err(dev, "Failed to get the irq\n");
> > > + goto err_irq;
> > > + }
> > > +
> > > + ret = devm_request_irq(dev, ret, rockchip_sfc_irq_handler,
> > > + 0, pdev->name, sfc);
> > > + if (ret) {
> > > + dev_err(dev, "Failed to request irq\n");
> > > +
> > > + return ret;
> > > + }
> > > +
> > > + ret = rockchip_sfc_init(sfc);
> > > + if (ret)
> > > + goto err_irq;
> > > +
> > > + sfc->max_iosize = rockchip_sfc_get_max_iosize(sfc);
> > > +
> > > + ret = spi_register_master(master);
> > > + if (ret)
> > > + goto err_irq;
> > > +
> > > + return 0;
> > > +
> > > +err_irq:
> > > + clk_disable_unprepare(sfc->clk);
> > > +err_clk:
> > > + clk_disable_unprepare(sfc->hclk);
> > > +err_hclk:
> > > + return ret;
> > > +}
> > > +
> > > +static int rockchip_sfc_remove(struct platform_device *pdev)
> > > +{
> > > + struct spi_master *master = platform_get_drvdata(pdev);
> > > + struct rockchip_sfc *sfc = platform_get_drvdata(pdev);
> > > +
> > > + spi_unregister_master(master);
> > > +
> > > + clk_disable_unprepare(sfc->clk);
> > > + clk_disable_unprepare(sfc->hclk);
> > > +
> > > + return 0;
> > > +}
> > > +
> > > +static const struct of_device_id rockchip_sfc_dt_ids[] = {
> > > + { .compatible = "rockchip,px30-sfc"},
> > > + { .compatible = "rockchip,rk3036-sfc"},
> > > + { .compatible = "rockchip,rk3308-sfc"},
> > > + { .compatible = "rockchip,rv1126-sfc"},
> > > + { /* sentinel */ }
> > > +};
> > > +MODULE_DEVICE_TABLE(of, rockchip_sfc_dt_ids);
> > > +
> > > +static struct platform_driver rockchip_sfc_driver = {
> > > + .driver = {
> > > + .name = "rockchip-sfc",
> > > + .of_match_table = rockchip_sfc_dt_ids,
> > > + },
> > > + .probe = rockchip_sfc_probe,
> > > + .remove = rockchip_sfc_remove,
> > > +};
> > > +module_platform_driver(rockchip_sfc_driver);
> > > +
> > > +MODULE_LICENSE("GPL v2");
> > > +MODULE_DESCRIPTION("Rockchip Serial Flash Controller Driver");
> > > +MODULE_AUTHOR("Shawn Lin <shawn.lin@rock-chips.com>");
> > > +MODULE_AUTHOR("Chris Morgan <macroalpha82@gmail.com>");
> > I know folks will hate on me for this (and for good reason given it
> > messes up IDs and stuff), but I prefer macromorgan@hotmail.com if my
> > email is in here, as that's the one I've been using for decades...
> ok.
> > > +MODULE_AUTHOR("Jon Lin <Jon.lin@rock-chips.com>");
> > > --
> > > 2.17.1
> > >
> > >
> > >
> >
> >
>
>