[PATCH net-next v3 0/4] Support bandwidth clamping in mana using net shapers

[PATCH net-next v3 0/4] Support bandwidth clamping in mana using net shapers

[Erni Sri Satya Vennela]

This patchset introduces hardware-backed bandwidth rate limiting
for MANA NICs via the net_shaper_ops interface, enabling efficient and
fine-grained traffic shaping directly on the device.

Previously, MANA lacked a mechanism for user-configurable bandwidth
control. With this addition, users can now configure shaping parameters,
allowing better traffic management and performance isolation.

The implementation includes the net_shaper_ops callbacks in the MANA
driver and supports one shaper per vport. Add shaping support via
mana_set_bw_clamp(), allowing the configuration of bandwidth rates
in 100 Mbps increments (minimum 100 Mbps). The driver validates input
and rejects unsupported values. On failure, it restores the previous
configuration which is queried using mana_query_link_cfg() or
retains the current state.

To prevent potential deadlocks introduced by net_shaper_ops, switch to
_locked variants of NAPI APIs when netdevops_lock is held during
VF setup and teardown.

Also, Add support for ethtool get_link_ksettings to report the maximum
link speed supported by the SKU in mbps.

These APIs when invoked on hardware that are older or that do
not support these APIs, the speed would be reported as UNKNOWN and
the net-shaper calls to set speed would fail.
---
Changes in v3:
* Rebase to latest net-next branch.
Changes in v2:
* Rebase to latest net-next branch.
* Edit commit message in
  "net: mana: Fix potential deadlocks in mana napi ops".
* Use netdev_lock_ops_to_full() instead of explicit if..else statements
  for napi APIs.
* Define GDMA_STATUS_CMD_UNSUPPORTED for unsupported HWC status code.
---

Erni Sri Satya Vennela (4):
  net: mana: Fix potential deadlocks in mana napi ops
  net: mana: Add support for net_shaper_ops
  net: mana: Add speed support in mana_get_link_ksettings
  net: mana: Handle unsupported HWC commands

 .../net/ethernet/microsoft/mana/hw_channel.c  |   4 +
 drivers/net/ethernet/microsoft/mana/mana_en.c | 195 +++++++++++++++++-
 .../ethernet/microsoft/mana/mana_ethtool.c    |   6 +
 include/net/mana/gdma.h                       |   1 +
 include/net/mana/mana.h                       |  42 ++++
 5 files changed, 239 insertions(+), 9 deletions(-)

-- 
2.34.1

[PATCH net-next v3 1/4] net: mana: Fix potential deadlocks in mana napi ops

[Erni Sri Satya Vennela]

When net_shaper_ops are enabled for MANA, netdev_ops_lock
becomes active.

MANA VF setup/teardown by netvsc follows this call chain:

netvsc_vf_setup()
        dev_change_flags()
		...
         __dev_open() OR __dev_close()

dev_change_flags() holds the netdev mutex via netdev_lock_ops.

Meanwhile, mana_create_txq() and mana_create_rxq() in mana_open()
path call NAPI APIs (netif_napi_add_tx(), netif_napi_add_weight(),
napi_enable()), which also try to acquire the same lock, risking
deadlock.

Similarly in the teardown path (mana_close()), netif_napi_disable()
and netif_napi_del(), contend for the same lock.

Switch to the _locked variants of these APIs to avoid deadlocks
when the netdev_ops_lock is held.

Fixes: d4c22ec680c8 ("net: hold netdev instance lock during ndo_open/ndo_stop")
Signed-off-by: Erni Sri Satya Vennela <ernis@linux.microsoft.com>
Reviewed-by: Haiyang Zhang <haiyangz@microsoft.com>
Reviewed-by: Shradha Gupta <shradhagupta@linux.microsoft.com>
Reviewed-by: Saurabh Singh Sengar <ssengar@linux.microsoft.com>
Reviewed-by: Long Li <longli@microsoft.com>
---
Changes in v3:
* Rebase to latest net-next branch.
Changes in v2:
* Use netdev_lock_ops_to_full() instead of if...else statements for napi
  APIs.
* Edit commit message.
---
 drivers/net/ethernet/microsoft/mana/mana_en.c | 28 +++++++++++++------
 1 file changed, 19 insertions(+), 9 deletions(-)

diff --git a/drivers/net/ethernet/microsoft/mana/mana_en.c b/drivers/net/ethernet/microsoft/mana/mana_en.c
index e68b8190bb7a..bcc33ea7aca3 100644
--- a/drivers/net/ethernet/microsoft/mana/mana_en.c
+++ b/drivers/net/ethernet/microsoft/mana/mana_en.c
@@ -1912,8 +1912,10 @@ static void mana_destroy_txq(struct mana_port_context *apc)
 		napi = &apc->tx_qp[i].tx_cq.napi;
 		if (apc->tx_qp[i].txq.napi_initialized) {
 			napi_synchronize(napi);
-			napi_disable(napi);
-			netif_napi_del(napi);
+			netdev_lock_ops_to_full(napi->dev);
+			napi_disable_locked(napi);
+			netif_napi_del_locked(napi);
+			netdev_unlock_full_to_ops(napi->dev);
 			apc->tx_qp[i].txq.napi_initialized = false;
 		}
 		mana_destroy_wq_obj(apc, GDMA_SQ, apc->tx_qp[i].tx_object);
@@ -2065,8 +2067,11 @@ static int mana_create_txq(struct mana_port_context *apc,
 
 		mana_create_txq_debugfs(apc, i);
 
-		netif_napi_add_tx(net, &cq->napi, mana_poll);
-		napi_enable(&cq->napi);
+		set_bit(NAPI_STATE_NO_BUSY_POLL, &cq->napi.state);
+		netdev_lock_ops_to_full(net);
+		netif_napi_add_locked(net, &cq->napi, mana_poll);
+		napi_enable_locked(&cq->napi);
+		netdev_unlock_full_to_ops(net);
 		txq->napi_initialized = true;
 
 		mana_gd_ring_cq(cq->gdma_cq, SET_ARM_BIT);
@@ -2102,9 +2107,10 @@ static void mana_destroy_rxq(struct mana_port_context *apc,
 	if (napi_initialized) {
 		napi_synchronize(napi);
 
-		napi_disable(napi);
-
-		netif_napi_del(napi);
+		netdev_lock_ops_to_full(napi->dev);
+		napi_disable_locked(napi);
+		netif_napi_del_locked(napi);
+		netdev_unlock_full_to_ops(napi->dev);
 	}
 	xdp_rxq_info_unreg(&rxq->xdp_rxq);
 
@@ -2355,14 +2361,18 @@ static struct mana_rxq *mana_create_rxq(struct mana_port_context *apc,
 
 	gc->cq_table[cq->gdma_id] = cq->gdma_cq;
 
-	netif_napi_add_weight(ndev, &cq->napi, mana_poll, 1);
+	netdev_lock_ops_to_full(ndev);
+	netif_napi_add_weight_locked(ndev, &cq->napi, mana_poll, 1);
+	netdev_unlock_full_to_ops(ndev);
 
 	WARN_ON(xdp_rxq_info_reg(&rxq->xdp_rxq, ndev, rxq_idx,
 				 cq->napi.napi_id));
 	WARN_ON(xdp_rxq_info_reg_mem_model(&rxq->xdp_rxq, MEM_TYPE_PAGE_POOL,
 					   rxq->page_pool));
 
-	napi_enable(&cq->napi);
+	netdev_lock_ops_to_full(ndev);
+	napi_enable_locked(&cq->napi);
+	netdev_unlock_full_to_ops(ndev);
 
 	mana_gd_ring_cq(cq->gdma_cq, SET_ARM_BIT);
 out:
-- 
2.34.1

[PATCH net-next v3 2/4] net: mana: Add support for net_shaper_ops

[Erni Sri Satya Vennela]

Introduce support for net_shaper_ops in the MANA driver,
enabling configuration of rate limiting on the MANA NIC.

To apply rate limiting, the driver issues a HWC command via
mana_set_bw_clamp() and updates the corresponding shaper object
in the net_shaper cache. If an error occurs during this process,
the driver restores the previous speed by querying the current link
configuration using mana_query_link_cfg().

The minimum supported bandwidth is 100 Mbps, and only values that are
exact multiples of 100 Mbps are allowed. Any other values are rejected.

To remove a shaper, the driver resets the bandwidth to the maximum
supported by the SKU using mana_set_bw_clamp() and clears the
associated cache entry. If an error occurs during this process,
the shaper details are retained.

On the hardware that does not support these APIs, the net-shaper
calls to set speed would fail.

Set the speed:
./tools/net/ynl/pyynl/cli.py \
 --spec Documentation/netlink/specs/net_shaper.yaml \
 --do set --json '{"ifindex":'$IFINDEX',
		   "handle":{"scope": "netdev", "id":'$ID' },
		   "bw-max": 200000000 }'

Get the shaper details:
./tools/net/ynl/pyynl/cli.py \
 --spec Documentation/netlink/specs/net_shaper.yaml \
 --do get --json '{"ifindex":'$IFINDEX',
		      "handle":{"scope": "netdev", "id":'$ID' }}'

> {'bw-max': 200000000,
> 'handle': {'scope': 'netdev'},
> 'ifindex': $IFINDEX,
> 'metric': 'bps'}

Delete the shaper object:
./tools/net/ynl/pyynl/cli.py \
 --spec Documentation/netlink/specs/net_shaper.yaml \
 --do delete --json '{"ifindex":'$IFINDEX',
		      "handle":{"scope": "netdev","id":'$ID' }}'

Signed-off-by: Erni Sri Satya Vennela <ernis@linux.microsoft.com>
Reviewed-by: Haiyang Zhang <haiyangz@microsoft.com>
Reviewed-by: Shradha Gupta <shradhagupta@linux.microsoft.com>
Reviewed-by: Saurabh Singh Sengar <ssengar@linux.microsoft.com>
Reviewed-by: Long Li <longli@microsoft.com>
---
Changes in v3:
* Rebase to latest net-next branch.
Changes in v2:
* No change.
---
 drivers/net/ethernet/microsoft/mana/mana_en.c | 155 ++++++++++++++++++
 include/net/mana/mana.h                       |  40 +++++
 2 files changed, 195 insertions(+)

diff --git a/drivers/net/ethernet/microsoft/mana/mana_en.c b/drivers/net/ethernet/microsoft/mana/mana_en.c
index bcc33ea7aca3..547dff450b6d 100644
--- a/drivers/net/ethernet/microsoft/mana/mana_en.c
+++ b/drivers/net/ethernet/microsoft/mana/mana_en.c
@@ -719,6 +719,78 @@ static int mana_change_mtu(struct net_device *ndev, int new_mtu)
 	return err;
 }
 
+static int mana_shaper_set(struct net_shaper_binding *binding,
+			   const struct net_shaper *shaper,
+			   struct netlink_ext_ack *extack)
+{
+	struct mana_port_context *apc = netdev_priv(binding->netdev);
+	u32 old_speed, rate;
+	int err;
+
+	if (shaper->handle.scope != NET_SHAPER_SCOPE_NETDEV) {
+		NL_SET_ERR_MSG_MOD(extack, "net shaper scope should be netdev");
+		return -EINVAL;
+	}
+
+	if (apc->handle.id && shaper->handle.id != apc->handle.id) {
+		NL_SET_ERR_MSG_MOD(extack, "Cannot create multiple shapers");
+		return -EOPNOTSUPP;
+	}
+
+	if (!shaper->bw_max || (shaper->bw_max % 100000000)) {
+		NL_SET_ERR_MSG_MOD(extack, "Please use multiples of 100Mbps for bandwidth");
+		return -EINVAL;
+	}
+
+	rate = div_u64(shaper->bw_max, 1000); /* Convert bps to Kbps */
+	rate = div_u64(rate, 1000);	      /* Convert Kbps to Mbps */
+
+	/* Get current speed */
+	err = mana_query_link_cfg(apc);
+	old_speed = (err) ? SPEED_UNKNOWN : apc->speed;
+
+	if (!err) {
+		err = mana_set_bw_clamp(apc, rate, TRI_STATE_TRUE);
+		apc->speed = (err) ? old_speed : rate;
+		apc->handle = (err) ? apc->handle : shaper->handle;
+	}
+
+	return err;
+}
+
+static int mana_shaper_del(struct net_shaper_binding *binding,
+			   const struct net_shaper_handle *handle,
+			   struct netlink_ext_ack *extack)
+{
+	struct mana_port_context *apc = netdev_priv(binding->netdev);
+	int err;
+
+	err = mana_set_bw_clamp(apc, 0, TRI_STATE_FALSE);
+
+	if (!err) {
+		/* Reset mana port context parameters */
+		apc->handle.id = 0;
+		apc->handle.scope = NET_SHAPER_SCOPE_UNSPEC;
+		apc->speed = 0;
+	}
+
+	return err;
+}
+
+static void mana_shaper_cap(struct net_shaper_binding *binding,
+			    enum net_shaper_scope scope,
+			    unsigned long *flags)
+{
+	*flags = BIT(NET_SHAPER_A_CAPS_SUPPORT_BW_MAX) |
+		 BIT(NET_SHAPER_A_CAPS_SUPPORT_METRIC_BPS);
+}
+
+static const struct net_shaper_ops mana_shaper_ops = {
+	.set = mana_shaper_set,
+	.delete = mana_shaper_del,
+	.capabilities = mana_shaper_cap,
+};
+
 static const struct net_device_ops mana_devops = {
 	.ndo_open		= mana_open,
 	.ndo_stop		= mana_close,
@@ -729,6 +801,7 @@ static const struct net_device_ops mana_devops = {
 	.ndo_bpf		= mana_bpf,
 	.ndo_xdp_xmit		= mana_xdp_xmit,
 	.ndo_change_mtu		= mana_change_mtu,
+	.net_shaper_ops         = &mana_shaper_ops,
 };
 
 static void mana_cleanup_port_context(struct mana_port_context *apc)
@@ -1162,6 +1235,86 @@ static int mana_cfg_vport_steering(struct mana_port_context *apc,
 	return err;
 }
 
+int mana_query_link_cfg(struct mana_port_context *apc)
+{
+	struct net_device *ndev = apc->ndev;
+	struct mana_query_link_config_resp resp = {};
+	struct mana_query_link_config_req req = {};
+	int err;
+
+	mana_gd_init_req_hdr(&req.hdr, MANA_QUERY_LINK_CONFIG,
+			     sizeof(req), sizeof(resp));
+
+	req.vport = apc->port_handle;
+	req.hdr.resp.msg_version = GDMA_MESSAGE_V2;
+
+	err = mana_send_request(apc->ac, &req, sizeof(req), &resp,
+				sizeof(resp));
+
+	if (err) {
+		netdev_err(ndev, "Failed to query link config: %d\n", err);
+		return err;
+	}
+
+	err = mana_verify_resp_hdr(&resp.hdr, MANA_QUERY_LINK_CONFIG,
+				   sizeof(resp));
+
+	if (err || resp.hdr.status) {
+		netdev_err(ndev, "Failed to query link config: %d, 0x%x\n", err,
+			   resp.hdr.status);
+		if (!err)
+			err = -EOPNOTSUPP;
+		return err;
+	}
+
+	if (resp.qos_unconfigured) {
+		err = -EINVAL;
+		return err;
+	}
+	apc->speed = resp.link_speed_mbps;
+	return 0;
+}
+
+int mana_set_bw_clamp(struct mana_port_context *apc, u32 speed,
+		      int enable_clamping)
+{
+	struct mana_set_bw_clamp_resp resp = {};
+	struct mana_set_bw_clamp_req req = {};
+	struct net_device *ndev = apc->ndev;
+	int err;
+
+	mana_gd_init_req_hdr(&req.hdr, MANA_SET_BW_CLAMP,
+			     sizeof(req), sizeof(resp));
+	req.vport = apc->port_handle;
+	req.link_speed_mbps = speed;
+	req.enable_clamping = enable_clamping;
+
+	err = mana_send_request(apc->ac, &req, sizeof(req), &resp,
+				sizeof(resp));
+
+	if (err) {
+		netdev_err(ndev, "Failed to set bandwidth clamp for speed %u, err = %d",
+			   speed, err);
+		return err;
+	}
+
+	err = mana_verify_resp_hdr(&resp.hdr, MANA_SET_BW_CLAMP,
+				   sizeof(resp));
+
+	if (err || resp.hdr.status) {
+		netdev_err(ndev, "Failed to set bandwidth clamp: %d, 0x%x\n", err,
+			   resp.hdr.status);
+		if (!err)
+			err = -EOPNOTSUPP;
+		return err;
+	}
+
+	if (resp.qos_unconfigured)
+		netdev_info(ndev, "QoS is unconfigured\n");
+
+	return 0;
+}
+
 int mana_create_wq_obj(struct mana_port_context *apc,
 		       mana_handle_t vport,
 		       u32 wq_type, struct mana_obj_spec *wq_spec,
@@ -3011,6 +3164,8 @@ static int mana_probe_port(struct mana_context *ac, int port_idx,
 		goto free_indir;
 	}
 
+	debugfs_create_u32("current_speed", 0400, apc->mana_port_debugfs, &apc->speed);
+
 	return 0;
 
 free_indir:
diff --git a/include/net/mana/mana.h b/include/net/mana/mana.h
index 4176edf1be71..038b18340e51 100644
--- a/include/net/mana/mana.h
+++ b/include/net/mana/mana.h
@@ -5,6 +5,7 @@
 #define _MANA_H
 
 #include <net/xdp.h>
+#include <net/net_shaper.h>
 
 #include "gdma.h"
 #include "hw_channel.h"
@@ -526,7 +527,12 @@ struct mana_port_context {
 	struct mutex vport_mutex;
 	int vport_use_count;
 
+	/* Net shaper handle*/
+	struct net_shaper_handle handle;
+
 	u16 port_idx;
+	/* Currently configured speed (mbps) */
+	u32 speed;
 
 	bool port_is_up;
 	bool port_st_save; /* Saved port state */
@@ -562,6 +568,9 @@ struct bpf_prog *mana_xdp_get(struct mana_port_context *apc);
 void mana_chn_setxdp(struct mana_port_context *apc, struct bpf_prog *prog);
 int mana_bpf(struct net_device *ndev, struct netdev_bpf *bpf);
 void mana_query_gf_stats(struct mana_port_context *apc);
+int mana_query_link_cfg(struct mana_port_context *apc);
+int mana_set_bw_clamp(struct mana_port_context *apc, u32 speed,
+		      int enable_clamping);
 void mana_query_phy_stats(struct mana_port_context *apc);
 int mana_pre_alloc_rxbufs(struct mana_port_context *apc, int mtu, int num_queues);
 void mana_pre_dealloc_rxbufs(struct mana_port_context *apc);
@@ -589,6 +598,8 @@ enum mana_command_code {
 	MANA_FENCE_RQ		= 0x20006,
 	MANA_CONFIG_VPORT_RX	= 0x20007,
 	MANA_QUERY_VPORT_CONFIG	= 0x20008,
+	MANA_QUERY_LINK_CONFIG	= 0x2000A,
+	MANA_SET_BW_CLAMP	= 0x2000B,
 	MANA_QUERY_PHY_STAT     = 0x2000c,
 
 	/* Privileged commands for the PF mode */
@@ -598,6 +609,35 @@ enum mana_command_code {
 	MANA_DEREGISTER_HW_PORT	= 0x28004,
 };
 
+/* Query Link Configuration*/
+struct mana_query_link_config_req {
+	struct gdma_req_hdr hdr;
+	mana_handle_t vport;
+}; /* HW DATA */
+
+struct mana_query_link_config_resp {
+	struct gdma_resp_hdr hdr;
+	u32 qos_speed_mbps;
+	u8 qos_unconfigured;
+	u8 reserved1[3];
+	u32 link_speed_mbps;
+	u8 reserved2[4];
+}; /* HW DATA */
+
+/* Set Bandwidth Clamp*/
+struct mana_set_bw_clamp_req {
+	struct gdma_req_hdr hdr;
+	mana_handle_t vport;
+	enum TRI_STATE enable_clamping;
+	u32 link_speed_mbps;
+}; /* HW DATA */
+
+struct mana_set_bw_clamp_resp {
+	struct gdma_resp_hdr hdr;
+	u8 qos_unconfigured;
+	u8 reserved[7];
+}; /* HW DATA */
+
 /* Query Device Configuration */
 struct mana_query_device_cfg_req {
 	struct gdma_req_hdr hdr;
-- 
2.34.1

[PATCH net-next v3 3/4] net: mana: Add speed support in mana_get_link_ksettings

[Erni Sri Satya Vennela]

Allow mana ethtool get_link_ksettings operation to report
the maximum speed supported by the SKU in mbps.

The driver retrieves this information by issuing a
HWC command to the hardware via mana_query_link_cfg(),
which retrieves the SKU's maximum supported speed.

These APIs when invoked on hardware that are older/do
not support these APIs, the speed would be reported as UNKNOWN.

Before:
$ethtool enP30832s1
> Settings for enP30832s1:
        Supported ports: [  ]
        Supported link modes:   Not reported
        Supported pause frame use: No
        Supports auto-negotiation: No
        Supported FEC modes: Not reported
        Advertised link modes:  Not reported
        Advertised pause frame use: No
        Advertised auto-negotiation: No
        Advertised FEC modes: Not reported
        Speed: Unknown!
        Duplex: Full
        Auto-negotiation: off
        Port: Other
        PHYAD: 0
        Transceiver: internal
        Link detected: yes

After:
$ethtool enP30832s1
> Settings for enP30832s1:
        Supported ports: [  ]
        Supported link modes:   Not reported
        Supported pause frame use: No
        Supports auto-negotiation: No
        Supported FEC modes: Not reported
        Advertised link modes:  Not reported
        Advertised pause frame use: No
        Advertised auto-negotiation: No
        Advertised FEC modes: Not reported
        Speed: 16000Mb/s
        Duplex: Full
        Auto-negotiation: off
        Port: Other
        PHYAD: 0
        Transceiver: internal
        Link detected: yes

Signed-off-by: Erni Sri Satya Vennela <ernis@linux.microsoft.com>
Reviewed-by: Haiyang Zhang <haiyangz@microsoft.com>
Reviewed-by: Shradha Gupta <shradhagupta@linux.microsoft.com>
Reviewed-by: Saurabh Singh Sengar <ssengar@linux.microsoft.com>
---
Changes in v3:
* Rebase to latest net-next branch.
Changes in v2:
* No change.
---
 drivers/net/ethernet/microsoft/mana/mana_en.c      | 1 +
 drivers/net/ethernet/microsoft/mana/mana_ethtool.c | 6 ++++++
 include/net/mana/mana.h                            | 2 ++
 3 files changed, 9 insertions(+)

diff --git a/drivers/net/ethernet/microsoft/mana/mana_en.c b/drivers/net/ethernet/microsoft/mana/mana_en.c
index 547dff450b6d..d7079e05dfb8 100644
--- a/drivers/net/ethernet/microsoft/mana/mana_en.c
+++ b/drivers/net/ethernet/microsoft/mana/mana_en.c
@@ -1272,6 +1272,7 @@ int mana_query_link_cfg(struct mana_port_context *apc)
 		return err;
 	}
 	apc->speed = resp.link_speed_mbps;
+	apc->max_speed = resp.qos_speed_mbps;
 	return 0;
 }
 
diff --git a/drivers/net/ethernet/microsoft/mana/mana_ethtool.c b/drivers/net/ethernet/microsoft/mana/mana_ethtool.c
index 4fb3a04994a2..a1afa75a9463 100644
--- a/drivers/net/ethernet/microsoft/mana/mana_ethtool.c
+++ b/drivers/net/ethernet/microsoft/mana/mana_ethtool.c
@@ -495,6 +495,12 @@ static int mana_set_ringparam(struct net_device *ndev,
 static int mana_get_link_ksettings(struct net_device *ndev,
 				   struct ethtool_link_ksettings *cmd)
 {
+	struct mana_port_context *apc = netdev_priv(ndev);
+	int err;
+
+	err = mana_query_link_cfg(apc);
+	cmd->base.speed = (err) ? SPEED_UNKNOWN : apc->max_speed;
+
 	cmd->base.duplex = DUPLEX_FULL;
 	cmd->base.port = PORT_OTHER;
 
diff --git a/include/net/mana/mana.h b/include/net/mana/mana.h
index 038b18340e51..e1030a7d2daa 100644
--- a/include/net/mana/mana.h
+++ b/include/net/mana/mana.h
@@ -533,6 +533,8 @@ struct mana_port_context {
 	u16 port_idx;
 	/* Currently configured speed (mbps) */
 	u32 speed;
+	/* Maximum speed supported by the SKU (mbps) */
+	u32 max_speed;
 
 	bool port_is_up;
 	bool port_st_save; /* Saved port state */
-- 
2.34.1

RE: [EXTERNAL] [PATCH net-next v3 3/4] net: mana: Add speed support in mana_get_link_ksettings

[Long Li]

> Subject: [PATCH net-next v3 3/4] net: mana: Add speed support in
> mana_get_link_ksettings
> 
> Allow mana ethtool get_link_ksettings operation to report the maximum speed
> supported by the SKU in mbps.
> 
> The driver retrieves this information by issuing a HWC command to the hardware
> via mana_query_link_cfg(), which retrieves the SKU's maximum supported speed.
> 
> These APIs when invoked on hardware that are older/do not support these APIs,
> the speed would be reported as UNKNOWN.
> 
> Before:
> $ethtool enP30832s1
> > Settings for enP30832s1:
>         Supported ports: [  ]
>         Supported link modes:   Not reported
>         Supported pause frame use: No
>         Supports auto-negotiation: No
>         Supported FEC modes: Not reported
>         Advertised link modes:  Not reported
>         Advertised pause frame use: No
>         Advertised auto-negotiation: No
>         Advertised FEC modes: Not reported
>         Speed: Unknown!
>         Duplex: Full
>         Auto-negotiation: off
>         Port: Other
>         PHYAD: 0
>         Transceiver: internal
>         Link detected: yes
> 
> After:
> $ethtool enP30832s1
> > Settings for enP30832s1:
>         Supported ports: [  ]
>         Supported link modes:   Not reported
>         Supported pause frame use: No
>         Supports auto-negotiation: No
>         Supported FEC modes: Not reported
>         Advertised link modes:  Not reported
>         Advertised pause frame use: No
>         Advertised auto-negotiation: No
>         Advertised FEC modes: Not reported
>         Speed: 16000Mb/s
>         Duplex: Full
>         Auto-negotiation: off
>         Port: Other
>         PHYAD: 0
>         Transceiver: internal
>         Link detected: yes
> 
> Signed-off-by: Erni Sri Satya Vennela <ernis@linux.microsoft.com>
> Reviewed-by: Haiyang Zhang <haiyangz@microsoft.com>
> Reviewed-by: Shradha Gupta <shradhagupta@linux.microsoft.com>
> Reviewed-by: Saurabh Singh Sengar <ssengar@linux.microsoft.com>

Reviewed-by: Long Li <longli@microsoft.com>

> ---
> Changes in v3:
> * Rebase to latest net-next branch.
> Changes in v2:
> * No change.
> ---
>  drivers/net/ethernet/microsoft/mana/mana_en.c      | 1 +
>  drivers/net/ethernet/microsoft/mana/mana_ethtool.c | 6 ++++++
>  include/net/mana/mana.h                            | 2 ++
>  3 files changed, 9 insertions(+)
> 
> diff --git a/drivers/net/ethernet/microsoft/mana/mana_en.c
> b/drivers/net/ethernet/microsoft/mana/mana_en.c
> index 547dff450b6d..d7079e05dfb8 100644
> --- a/drivers/net/ethernet/microsoft/mana/mana_en.c
> +++ b/drivers/net/ethernet/microsoft/mana/mana_en.c
> @@ -1272,6 +1272,7 @@ int mana_query_link_cfg(struct mana_port_context
> *apc)
>  		return err;
>  	}
>  	apc->speed = resp.link_speed_mbps;
> +	apc->max_speed = resp.qos_speed_mbps;
>  	return 0;
>  }
> 
> diff --git a/drivers/net/ethernet/microsoft/mana/mana_ethtool.c
> b/drivers/net/ethernet/microsoft/mana/mana_ethtool.c
> index 4fb3a04994a2..a1afa75a9463 100644
> --- a/drivers/net/ethernet/microsoft/mana/mana_ethtool.c
> +++ b/drivers/net/ethernet/microsoft/mana/mana_ethtool.c
> @@ -495,6 +495,12 @@ static int mana_set_ringparam(struct net_device *ndev,
> static int mana_get_link_ksettings(struct net_device *ndev,
>  				   struct ethtool_link_ksettings *cmd)  {
> +	struct mana_port_context *apc = netdev_priv(ndev);
> +	int err;
> +
> +	err = mana_query_link_cfg(apc);
> +	cmd->base.speed = (err) ? SPEED_UNKNOWN : apc->max_speed;
> +
>  	cmd->base.duplex = DUPLEX_FULL;
>  	cmd->base.port = PORT_OTHER;
> 
> diff --git a/include/net/mana/mana.h b/include/net/mana/mana.h index
> 038b18340e51..e1030a7d2daa 100644
> --- a/include/net/mana/mana.h
> +++ b/include/net/mana/mana.h
> @@ -533,6 +533,8 @@ struct mana_port_context {
>  	u16 port_idx;
>  	/* Currently configured speed (mbps) */
>  	u32 speed;
> +	/* Maximum speed supported by the SKU (mbps) */
> +	u32 max_speed;
> 
>  	bool port_is_up;
>  	bool port_st_save; /* Saved port state */
> --
> 2.34.1

[PATCH net-next v3 4/4] net: mana: Handle unsupported HWC commands

[Erni Sri Satya Vennela]

If any of the HWC commands are not recognized by the
underlying hardware, the hardware returns the response
header status of -1. Log the information using
netdev_info_once to avoid multiple error logs in dmesg.

Signed-off-by: Erni Sri Satya Vennela <ernis@linux.microsoft.com>
Reviewed-by: Haiyang Zhang <haiyangz@microsoft.com>
Reviewed-by: Shradha Gupta <shradhagupta@linux.microsoft.com>
Reviewed-by: Saurabh Singh Sengar <ssengar@linux.microsoft.com>
Reviewed-by: Dipayaan Roy <dipayanroy@linux.microsoft.com>
---
Changes in v3:
* Rebase to latest net-next branch.
Changes in v2:
* Define GDMA_STATUS_CMD_UNSUPPORTED for unsupported HWC status code
  instead of using -1.
---
 drivers/net/ethernet/microsoft/mana/hw_channel.c |  4 ++++
 drivers/net/ethernet/microsoft/mana/mana_en.c    | 11 +++++++++++
 include/net/mana/gdma.h                          |  1 +
 3 files changed, 16 insertions(+)

diff --git a/drivers/net/ethernet/microsoft/mana/hw_channel.c b/drivers/net/ethernet/microsoft/mana/hw_channel.c
index 3d3677c0d014..650d22654d49 100644
--- a/drivers/net/ethernet/microsoft/mana/hw_channel.c
+++ b/drivers/net/ethernet/microsoft/mana/hw_channel.c
@@ -891,6 +891,10 @@ int mana_hwc_send_request(struct hw_channel_context *hwc, u32 req_len,
 	}
 
 	if (ctx->status_code && ctx->status_code != GDMA_STATUS_MORE_ENTRIES) {
+		if (ctx->status_code == GDMA_STATUS_CMD_UNSUPPORTED) {
+			err = -EOPNOTSUPP;
+			goto out;
+		}
 		if (req_msg->req.msg_type != MANA_QUERY_PHY_STAT)
 			dev_err(hwc->dev, "HWC: Failed hw_channel req: 0x%x\n",
 				ctx->status_code);
diff --git a/drivers/net/ethernet/microsoft/mana/mana_en.c b/drivers/net/ethernet/microsoft/mana/mana_en.c
index d7079e05dfb8..5aee7bda1504 100644
--- a/drivers/net/ethernet/microsoft/mana/mana_en.c
+++ b/drivers/net/ethernet/microsoft/mana/mana_en.c
@@ -847,6 +847,9 @@ static int mana_send_request(struct mana_context *ac, void *in_buf,
 	err = mana_gd_send_request(gc, in_len, in_buf, out_len,
 				   out_buf);
 	if (err || resp->status) {
+		if (err == -EOPNOTSUPP)
+			return err;
+
 		if (req->req.msg_type != MANA_QUERY_PHY_STAT)
 			dev_err(dev, "Failed to send mana message: %d, 0x%x\n",
 				err, resp->status);
@@ -1252,6 +1255,10 @@ int mana_query_link_cfg(struct mana_port_context *apc)
 				sizeof(resp));
 
 	if (err) {
+		if (err == -EOPNOTSUPP) {
+			netdev_info_once(ndev, "MANA_QUERY_LINK_CONFIG not supported\n");
+			return err;
+		}
 		netdev_err(ndev, "Failed to query link config: %d\n", err);
 		return err;
 	}
@@ -1294,6 +1301,10 @@ int mana_set_bw_clamp(struct mana_port_context *apc, u32 speed,
 				sizeof(resp));
 
 	if (err) {
+		if (err == -EOPNOTSUPP) {
+			netdev_info_once(ndev, "MANA_SET_BW_CLAMP not supported\n");
+			return err;
+		}
 		netdev_err(ndev, "Failed to set bandwidth clamp for speed %u, err = %d",
 			   speed, err);
 		return err;
diff --git a/include/net/mana/gdma.h b/include/net/mana/gdma.h
index bfae59202669..fdf144988cec 100644
--- a/include/net/mana/gdma.h
+++ b/include/net/mana/gdma.h
@@ -10,6 +10,7 @@
 #include "shm_channel.h"
 
 #define GDMA_STATUS_MORE_ENTRIES	0x00000105
+#define GDMA_STATUS_CMD_UNSUPPORTED	0xffffffff
 
 /* Structures labeled with "HW DATA" are exchanged with the hardware. All of
  * them are naturally aligned and hence don't need __packed.
-- 
2.34.1

Re: [PATCH net-next v3 0/4] Support bandwidth clamping in mana using net shapers

[patchwork-bot+netdevbpf]

Hello:

This series was applied to netdev/net-next.git (main)
by Paolo Abeni <pabeni@redhat.com>:

On Tue, 17 Jun 2025 00:17:32 -0700 you wrote:
> This patchset introduces hardware-backed bandwidth rate limiting
> for MANA NICs via the net_shaper_ops interface, enabling efficient and
> fine-grained traffic shaping directly on the device.
> 
> Previously, MANA lacked a mechanism for user-configurable bandwidth
> control. With this addition, users can now configure shaping parameters,
> allowing better traffic management and performance isolation.
> 
> [...]

Here is the summary with links:
  - [net-next,v3,1/4] net: mana: Fix potential deadlocks in mana napi ops
    https://git.kernel.org/netdev/net-next/c/d5c8f0e4e0cb
  - [net-next,v3,2/4] net: mana: Add support for net_shaper_ops
    https://git.kernel.org/netdev/net-next/c/75cabb46935b
  - [net-next,v3,3/4] net: mana: Add speed support in mana_get_link_ksettings
    https://git.kernel.org/netdev/net-next/c/a6d5edf11e0c
  - [net-next,v3,4/4] net: mana: Handle unsupported HWC commands
    https://git.kernel.org/netdev/net-next/c/ca8ac489ca33

You are awesome, thank you!
-- 
Deet-doot-dot, I am a bot.
https://korg.docs.kernel.org/patchwork/pwbot.html