From: "John Stoffel" <john@stoffel.org>
To: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Kevin Radloff <radsaq@gmail.com>, linux-kernel@vger.kernel.org
Subject: Re: Updated libata PATA patch
Date: Thu, 11 May 2006 22:34:54 -0400 [thread overview]
Message-ID: <17507.62542.780940.914596@smtp.charter.net> (raw)
In-Reply-To: <1147270145.17886.42.camel@localhost.localdomain>
Alan,
I just tried to use the IDE2 patches to 2.6.17-rc3 tonight. I've got
an old Dell Precision 610, Dual 550Mhz Xeon, 768mb of RAM. My root
disk is SCSI, with hda a Samsung DVD/ROM, CDRW drive. I've got an
HPT302 controller with a pair of 120gb IDE disks. I've also got an
addon PCI USB/Firewire Card, an old Cyclom-Y ISA serial port card,
Matrox G450 AGP card, builtin Adaptec SCSI cards, DLT 7000 tape
drive. Probably other stuff as well.
Here's the lspci output:
> lspci
0000:00:00.0 Host bridge: Intel Corporation 440GX - 82443GX Host bridge
0000:00:01.0 PCI bridge: Intel Corporation 440GX - 82443GX AGP bridge
0000:00:07.0 ISA bridge: Intel Corporation 82371AB/EB/MB PIIX4 ISA (rev 02)
0000:00:07.1 IDE interface: Intel Corporation 82371AB/EB/MB PIIX4 IDE (rev 01)
0000:00:07.2 USB Controller: Intel Corporation 82371AB/EB/MB PIIX4 USB (rev 01)
0000:00:07.3 Bridge: Intel Corporation 82371AB/EB/MB PIIX4 ACPI (rev 02)
0000:00:0d.0 RAID bus controller: Triones Technologies, Inc. HPT302 (rev 01)
0000:00:0e.0 Multimedia audio controller: Ensoniq ES1371 [AudioPCI-97] (rev 06)
0000:00:11.0 Ethernet controller: 3Com Corporation 3c905B 100BaseTX [Cyclone] (rev 24)
0000:00:13.0 PCI bridge: Digital Equipment Corporation DECchip 21152 (rev 03)
0000:01:00.0 VGA compatible controller: Matrox Graphics, Inc. G400/G450 (rev 82)
0000:02:06.0 PCI bridge: Hint Corp HB6 Universal PCI-PCI bridge (non-transparent mode) (rev 13)
0000:02:0a.0 SCSI storage controller: Adaptec AHA-2940U2/U2W / 7890/7891
0000:02:0e.0 SCSI storage controller: Adaptec AIC-7880U (rev 01)
0000:03:08.0 USB Controller: NEC Corporation USB (rev 41)
0000:03:08.1 USB Controller: NEC Corporation USB (rev 41)
0000:03:08.2 USB Controller: NEC Corporation USB 2.0 (rev 02)
0000:03:0b.0 FireWire (IEEE 1394): Texas Instruments TSB12LV26 IEEE-1394 Controller (Link)
n> cat /proc/interrupts
CPU0 CPU1
0: 237231 227203 IO-APIC-edge timer
1: 1213 2640 IO-APIC-edge i8042
8: 3 1 IO-APIC-edge rtc
9: 0 0 IO-APIC-level acpi
11: 2265 2258 IO-APIC-edge Cyclom-Y
12: 10217 2344 IO-APIC-edge i8042
14: 7934 7911 IO-APIC-edge ide0
16: 395587 368729 IO-APIC-level ide2, ide3, ehci_hcd:usb1, mga@pci:0000:01:00.0
17: 3559 1 IO-APIC-level Ensoniq AudioPCI, ohci1394, eth0
18: 7146 4967 IO-APIC-level aic7xxx, aic7xxx, ohci_hcd:usb2
19: 174376 184174 IO-APIC-level uhci_hcd:usb3, ohci_hcd:usb4
NMI: 0 0
LOC: 464327 464326
ERR: 0
MIS: 0
Booting up it was *slow*... slower than normal. I got the following
oops, copied down from a photo I took, since it didn't end up getting
written to disk.
.
.
.
irq 16: nobody cared (try booting with the "irqpoll" option)
<c013d034> __report_bad_irq_0x24/0x90 <c013d13f> note_interrupt+0x9f/0x260
<c031ab78> usb_hcd_irq+0x28/0x60 <c013c993> handle_IRQ_event+0x33/0x70
<c013ca64> __do_IRQ+0xf4/0x100 <c0105909> do_IRQ+0x19/0x30
<c0103962> common_interrupt+0x1a/0x20 <c0101b80> default_idle+0x0/0x60
<c010bac> default_idle+0x2c/0x60 <c0101c48> cpu_idle+0x68/0x90
<c0542729> start_kernel+0x289/0x400 <c0542230> unknown_bootoption+0x0/0x270
handlers:
[<c0302d20>] (ata_interrupt+0x0/0x150)
[c031ab50>] (usb_hcd_irq+0x0/0x60)
Disabling IRQ #16
Please let me know if there's any more information I can provide.
I'll try to get a serial cable on there so I can capture the boot log
better to another host, but no sure when I'll be able to do this.
John
next prev parent reply other threads:[~2006-05-12 2:34 UTC|newest]
Thread overview: 12+ messages / expand[flat|nested] mbox.gz Atom feed top
2006-05-09 17:44 Updated libata PATA patch Alan Cox
2006-05-10 1:48 ` Kevin Radloff
2006-05-10 14:09 ` Alan Cox
2006-05-10 16:05 ` Kevin Radloff
2006-05-10 16:39 ` Alan Cox
2006-05-10 16:39 ` Kevin Radloff
2006-05-15 22:08 ` Alan Cox
2006-05-15 23:13 ` Alan Cox
2006-05-12 2:34 ` John Stoffel [this message]
2006-05-15 2:46 ` John Stoffel
2006-05-11 19:06 ` Matthieu CASTET
2006-05-12 23:04 ` Guennadi Liakhovetski
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=17507.62542.780940.914596@smtp.charter.net \
--to=john@stoffel.org \
--cc=alan@lxorguk.ukuu.org.uk \
--cc=linux-kernel@vger.kernel.org \
--cc=radsaq@gmail.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox