[PATCH RESEND net-next v5 0/2] Add support for the IPQ5018 Internal GE PHY

[PATCH RESEND net-next v5 0/2] Add support for the IPQ5018 Internal GE PHY

[George Moussalem via B4 Relay]

The IPQ5018 SoC contains an internal Gigabit Ethernet PHY with its
output pins that provide an MDI interface to either an external switch
in a PHY to PHY link architecture or directly to an attached RJ45
connector.

The PHY supports 10BASE-T/100BASE-TX/1000BASE-T link modes in SGMII
interface mode, CDT, auto-negotiation and 802.3az EEE.

The LDO controller found in the IPQ5018 SoC needs to be enabled to drive
power to the CMN Ethernet Block (CMN BLK) which the GE PHY depends on.
The LDO must be enabled in TCSR by writing to a specific register.

In a phy to phy architecture, DAC values need to be set to accommodate
for the short cable length.

Signed-off-by: George Moussalem <george.moussalem@outlook.com>
---
Changes in v5:
- No changes to code, but this version contains 2 out of 5 patches for
  merge into net-next specifically as requested by Jakub
- Picked by Andrew's RB tag on patch ("net: phy: qcom: at803x: Add Qualcomm IPQ5018 Internal PHY support")
- Removed unused macro definition (IPQ5018_TCSR_ETH_LDO_READY)
- Reverted sorting of header files for which a separate patch can be
  submitted
- Added a comment to explain why the FIFO buffer needs to be reset
- Do not initialize local variable as caught by Russell
- Updated macro definition names to more accurately describe the PHY
  registers and their functions
- Include SGMII as supported interface mode in driver commit message
- Changed error handling of acquirement of PHY reset to use IR_ERR
  instead of IS_ERR_OR_NULL
- Link to v4: https://lore.kernel.org/r/20250609-ipq5018-ge-phy-v4-0-1d3a125282c3@outlook.com

Changes in v4:
- Updated description of qcom,dac-preset-short-cable property in
  accordance with Andrew's recommendation to indicate that if the
  property is not set, no DAC values will be modified.
- Added newlines between properties
- Added PHY ID as compatible in DT bindings for conditional check to
  evaluate correctly. Did a 'git grep' on all other PHY IDs defined in
  the driver but none are explicitly referenced so I haven't added them
- Link to v3: https://lore.kernel.org/r/20250602-ipq5018-ge-phy-v3-0-421337a031b2@outlook.com

Changes in v3:
- Replace bitmask of GEPHY_MISC_ARES with GENMASK as suggested by Konrad
- Removed references to RX and TX clocks as the driver need not
  explicitly enable them. The GCC gatecontrols and routes the PHY's
  output clocks, registered in the DT as fixed clocks, back to the PHY.
  The bindings file has been updated accordingly.
- Removed acquisition and enablement of RX and TX clocks from the driver
- Link to v2: https://lore.kernel.org/r/20250528-ipq5018-ge-phy-v2-0-dd063674c71c@outlook.com

Changes in v2:
- Moved values for MDAC and EDAC into the driver and converted DT
  property qca,dac to a new boolean: qcom,dac-preset-short-cable as per
  discussion.
- Added compatible string along with a condition with a description of
  properties including clocks, resets, and qcom,dac-preset-short-cable
  in the bindings to address bindings issues reported by Rob and to
  bypass restrictions on nr of clocks and resets in ethernet-phy.yaml
- Added example to bindings file
- Renamed all instances of IPQ5018_PHY_MMD3* macros to IPQ5018_PHY_PCS*
- Removed qca,eth-ldo-ready property and moved the TCSR register to the
  mdio bus the phy is on as there's already support for setting this reg
  property in the mdio-ipq4019 driver as per commit:
  23a890d493e3ec1e957bc925fabb120962ae90a7
- Explicitly probe on PHY ID as otherwise the PHY wouldn't come up and
  initialize as found during further testing when the kernel is flashed
  to NAND
- Link to v1: https://lore.kernel.org/r/20250525-ipq5018-ge-phy-v1-0-ddab8854e253@outlook.com

---
George Moussalem (2):
      dt-bindings: net: qca,ar803x: Add IPQ5018 Internal GE PHY support
      net: phy: qcom: at803x: Add Qualcomm IPQ5018 Internal PHY support

 .../devicetree/bindings/net/qca,ar803x.yaml        |  43 ++++++
 drivers/net/phy/qcom/Kconfig                       |   2 +-
 drivers/net/phy/qcom/at803x.c                      | 167 +++++++++++++++++++++
 3 files changed, 211 insertions(+), 1 deletion(-)
---
base-commit: 5d6d67c4cb10a4b4d3ae35758d5eeed6239afdc8
change-id: 20250430-ipq5018-ge-phy-db654afa4ced

Best regards,
-- 
George Moussalem <george.moussalem@outlook.com>

[PATCH RESEND net-next v5 1/2] dt-bindings: net: qca,ar803x: Add IPQ5018 Internal GE PHY support

[George Moussalem via B4 Relay]

From: George Moussalem <george.moussalem@outlook.com>

Document the IPQ5018 Internal Gigabit Ethernet PHY found in the IPQ5018
SoC. Its output pins provide an MDI interface to either an external
switch in a PHY to PHY link scenario or is directly attached to an RJ45
connector.

The PHY supports 10/100/1000 mbps link modes, CDT, auto-negotiation and
802.3az EEE.

For operation, the LDO controller found in the IPQ5018 SoC for which
there is provision in the mdio-4019 driver.

Two common archictures across IPQ5018 boards are:
1. IPQ5018 PHY --> MDI --> RJ45 connector
2. IPQ5018 PHY --> MDI --> External PHY
In a phy to phy architecture, the DAC needs to be configured to
accommodate for the short cable length. As such, add an optional boolean
property so the driver sets preset DAC register values accordingly.

Signed-off-by: George Moussalem <george.moussalem@outlook.com>
---
 .../devicetree/bindings/net/qca,ar803x.yaml        | 43 ++++++++++++++++++++++
 1 file changed, 43 insertions(+)

diff --git a/Documentation/devicetree/bindings/net/qca,ar803x.yaml b/Documentation/devicetree/bindings/net/qca,ar803x.yaml
index 3acd09f0da863137f8a05e435a1fd28a536c2acd..7ae5110e7aa2cc97498a0ec46b67d8ed8440f3f2 100644
--- a/Documentation/devicetree/bindings/net/qca,ar803x.yaml
+++ b/Documentation/devicetree/bindings/net/qca,ar803x.yaml
@@ -16,8 +16,37 @@ description: |
 
 allOf:
   - $ref: ethernet-phy.yaml#
+  - if:
+      properties:
+        compatible:
+          contains:
+            enum:
+              - ethernet-phy-id004d.d0c0
+
+    then:
+      properties:
+        reg:
+          const: 7  # This PHY is always at MDIO address 7 in the IPQ5018 SoC
+
+        resets:
+          items:
+            - description:
+                GE PHY MISC reset which triggers a reset across MDC, DSP, RX, and TX lines.
+
+        qcom,dac-preset-short-cable:
+          description:
+            Set if this phy is connected to another phy to adjust the values for
+            MDAC and EDAC to adjust amplitude, bias current settings, and error
+            detection and correction algorithm to accommodate for short cable length.
+            If not set, DAC values are not modified and it is assumed the MDI output pins
+            of this PHY are directly connected to an RJ45 connector.
+          type: boolean
 
 properties:
+  compatible:
+    enum:
+      - ethernet-phy-id004d.d0c0
+
   qca,clk-out-frequency:
     description: Clock output frequency in Hertz.
     $ref: /schemas/types.yaml#/definitions/uint32
@@ -132,3 +161,17 @@ examples:
             };
         };
     };
+  - |
+    #include <dt-bindings/reset/qcom,gcc-ipq5018.h>
+
+    mdio {
+        #address-cells = <1>;
+        #size-cells = <0>;
+
+        ge_phy: ethernet-phy@7 {
+            compatible = "ethernet-phy-id004d.d0c0";
+            reg = <7>;
+
+            resets = <&gcc GCC_GEPHY_MISC_ARES>;
+        };
+    };

-- 
2.49.0

Re: [PATCH RESEND net-next v5 1/2] dt-bindings: net: qca,ar803x: Add IPQ5018 Internal GE PHY support

[Jakub Kicinski]

On Fri, 13 Jun 2025 05:55:07 +0400 George Moussalem via B4 Relay wrote:
> From: George Moussalem <george.moussalem@outlook.com>
> 
> Document the IPQ5018 Internal Gigabit Ethernet PHY found in the IPQ5018
> SoC. Its output pins provide an MDI interface to either an external
> switch in a PHY to PHY link scenario or is directly attached to an RJ45
> connector.
> 
> The PHY supports 10/100/1000 mbps link modes, CDT, auto-negotiation and
> 802.3az EEE.
> 
> For operation, the LDO controller found in the IPQ5018 SoC for which
> there is provision in the mdio-4019 driver.
> 
> Two common archictures across IPQ5018 boards are:
> 1. IPQ5018 PHY --> MDI --> RJ45 connector
> 2. IPQ5018 PHY --> MDI --> External PHY
> In a phy to phy architecture, the DAC needs to be configured to
> accommodate for the short cable length. As such, add an optional boolean
> property so the driver sets preset DAC register values accordingly.

Hi DT Maintainers!  Is this in anyone's review queue?
I see some comments from Rob on v2 but no reviews since.

Re: [PATCH RESEND net-next v5 1/2] dt-bindings: net: qca,ar803x: Add IPQ5018 Internal GE PHY support

[Krzysztof Kozlowski]

On Fri, Jun 13, 2025 at 05:55:07AM +0400, George Moussalem wrote:
> Document the IPQ5018 Internal Gigabit Ethernet PHY found in the IPQ5018
> SoC. Its output pins provide an MDI interface to either an external
> switch in a PHY to PHY link scenario or is directly attached to an RJ45
> connector.
> 
> The PHY supports 10/100/1000 mbps link modes, CDT, auto-negotiation and
> 802.3az EEE.
> 
> For operation, the LDO controller found in the IPQ5018 SoC for which
> there is provision in the mdio-4019 driver.
> 
> Two common archictures across IPQ5018 boards are:
> 1. IPQ5018 PHY --> MDI --> RJ45 connector
> 2. IPQ5018 PHY --> MDI --> External PHY
> In a phy to phy architecture, the DAC needs to be configured to
> accommodate for the short cable length. As such, add an optional boolean
> property so the driver sets preset DAC register values accordingly.
> 
> Signed-off-by: George Moussalem <george.moussalem@outlook.com>
> ---
>  .../devicetree/bindings/net/qca,ar803x.yaml        | 43 ++++++++++++++++++++++
>  1 file changed, 43 insertions(+)

Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>

Best regards,
Krzysztof

[PATCH RESEND net-next v5 2/2] net: phy: qcom: at803x: Add Qualcomm IPQ5018 Internal PHY support

[George Moussalem via B4 Relay]

From: George Moussalem <george.moussalem@outlook.com>

The IPQ5018 SoC contains a single internal Gigabit Ethernet PHY which
provides an MDI interface directly to an RJ45 connector or an external
switch over a PHY to PHY link.

The PHY supports 10BASE-T/100BASE-TX/1000BASE-T link modes in SGMII
interface mode, CDT, auto-negotiation and 802.3az EEE.

Let's add support for this PHY in the at803x driver as it falls within
the Qualcomm Atheros OUI.

Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: George Moussalem <george.moussalem@outlook.com>
---
 drivers/net/phy/qcom/Kconfig  |   2 +-
 drivers/net/phy/qcom/at803x.c | 167 ++++++++++++++++++++++++++++++++++++++++++
 2 files changed, 168 insertions(+), 1 deletion(-)

diff --git a/drivers/net/phy/qcom/Kconfig b/drivers/net/phy/qcom/Kconfig
index 570626cc8e14d3e6615f74a6377f0f7c9f723e89..84239e08a8dfa466b0a7b2a5ec724a168b692cd2 100644
--- a/drivers/net/phy/qcom/Kconfig
+++ b/drivers/net/phy/qcom/Kconfig
@@ -7,7 +7,7 @@ config AT803X_PHY
 	select QCOM_NET_PHYLIB
 	depends on REGULATOR
 	help
-	  Currently supports the AR8030, AR8031, AR8033, AR8035 model
+	  Currently supports the AR8030, AR8031, AR8033, AR8035, IPQ5018 model
 
 config QCA83XX_PHY
 	tristate "Qualcomm Atheros QCA833x PHYs"
diff --git a/drivers/net/phy/qcom/at803x.c b/drivers/net/phy/qcom/at803x.c
index 26350b962890b0321153d74758b13d817407d094..43e604171828ce35d5950e02b1d08ee3e4523fdc 100644
--- a/drivers/net/phy/qcom/at803x.c
+++ b/drivers/net/phy/qcom/at803x.c
@@ -19,6 +19,7 @@
 #include <linux/regulator/consumer.h>
 #include <linux/of.h>
 #include <linux/phylink.h>
+#include <linux/reset.h>
 #include <linux/sfp.h>
 #include <dt-bindings/net/qca-ar803x.h>
 
@@ -96,6 +97,8 @@
 #define ATH8035_PHY_ID				0x004dd072
 #define AT8030_PHY_ID_MASK			0xffffffef
 
+#define IPQ5018_PHY_ID				0x004dd0c0
+
 #define QCA9561_PHY_ID				0x004dd042
 
 #define AT803X_PAGE_FIBER			0
@@ -108,6 +111,48 @@
 /* disable hibernation mode */
 #define AT803X_DISABLE_HIBERNATION_MODE		BIT(2)
 
+#define IPQ5018_PHY_FIFO_CONTROL		0x19
+#define IPQ5018_PHY_FIFO_RESET			GENMASK(1, 0)
+
+#define IPQ5018_PHY_DEBUG_EDAC			0x4380
+#define IPQ5018_PHY_MMD1_MDAC			0x8100
+#define IPQ5018_PHY_DAC_MASK			GENMASK(15, 8)
+
+/* MDAC and EDAC values for short cable length */
+#define IPQ5018_PHY_DEBUG_EDAC_VAL		0x10
+#define IPQ5018_PHY_MMD1_MDAC_VAL		0x10
+
+#define IPQ5018_PHY_MMD1_MSE_THRESH1		0x1000
+#define IPQ5018_PHY_MMD1_MSE_THRESH2		0x1001
+#define IPQ5018_PHY_PCS_EEE_TX_TIMER		0x8008
+#define IPQ5018_PHY_PCS_EEE_RX_TIMER		0x8009
+#define IPQ5018_PHY_PCS_CDT_THRESH_CTRL3	0x8074
+#define IPQ5018_PHY_PCS_CDT_THRESH_CTRL4	0x8075
+#define IPQ5018_PHY_PCS_CDT_THRESH_CTRL5	0x8076
+#define IPQ5018_PHY_PCS_CDT_THRESH_CTRL6	0x8077
+#define IPQ5018_PHY_PCS_CDT_THRESH_CTRL7	0x8078
+#define IPQ5018_PHY_PCS_CDT_THRESH_CTRL9	0x807a
+#define IPQ5018_PHY_PCS_CDT_THRESH_CTRL13	0x807e
+#define IPQ5018_PHY_PCS_CDT_THRESH_CTRL14	0x807f
+
+#define IPQ5018_PHY_MMD1_MSE_THRESH1_VAL	0xf1
+#define IPQ5018_PHY_MMD1_MSE_THRESH2_VAL	0x1f6
+#define IPQ5018_PHY_PCS_EEE_TX_TIMER_VAL	0x7880
+#define IPQ5018_PHY_PCS_EEE_RX_TIMER_VAL	0xc8
+#define IPQ5018_PHY_PCS_CDT_THRESH_CTRL3_VAL	0xc040
+#define IPQ5018_PHY_PCS_CDT_THRESH_CTRL4_VAL	0xa060
+#define IPQ5018_PHY_PCS_CDT_THRESH_CTRL5_VAL	0xc040
+#define IPQ5018_PHY_PCS_CDT_THRESH_CTRL6_VAL	0xa060
+#define IPQ5018_PHY_PCS_CDT_THRESH_CTRL7_VAL	0xc24c
+#define IPQ5018_PHY_PCS_CDT_THRESH_CTRL9_VAL	0xc060
+#define IPQ5018_PHY_PCS_CDT_THRESH_CTRL13_VAL	0xb060
+#define IPQ5018_PHY_PCS_NEAR_ECHO_THRESH_VAL	0x90b0
+
+#define IPQ5018_PHY_DEBUG_ANA_LDO_EFUSE		0x1
+#define IPQ5018_PHY_DEBUG_ANA_LDO_EFUSE_MASK	GENMASK(7, 4)
+#define IPQ5018_PHY_DEBUG_ANA_LDO_EFUSE_DEFAULT	0x50
+#define IPQ5018_PHY_DEBUG_ANA_DAC_FILTER	0xa080
+
 MODULE_DESCRIPTION("Qualcomm Atheros AR803x PHY driver");
 MODULE_AUTHOR("Matus Ujhelyi");
 MODULE_LICENSE("GPL");
@@ -133,6 +178,11 @@ struct at803x_context {
 	u16 led_control;
 };
 
+struct ipq5018_priv {
+	struct reset_control *rst;
+	bool set_short_cable_dac;
+};
+
 static int at803x_write_page(struct phy_device *phydev, int page)
 {
 	int mask;
@@ -987,6 +1037,109 @@ static int at8035_probe(struct phy_device *phydev)
 	return at8035_parse_dt(phydev);
 }
 
+static int ipq5018_cable_test_start(struct phy_device *phydev)
+{
+	phy_write_mmd(phydev, MDIO_MMD_PCS, IPQ5018_PHY_PCS_CDT_THRESH_CTRL3,
+		      IPQ5018_PHY_PCS_CDT_THRESH_CTRL3_VAL);
+	phy_write_mmd(phydev, MDIO_MMD_PCS, IPQ5018_PHY_PCS_CDT_THRESH_CTRL4,
+		      IPQ5018_PHY_PCS_CDT_THRESH_CTRL4_VAL);
+	phy_write_mmd(phydev, MDIO_MMD_PCS, IPQ5018_PHY_PCS_CDT_THRESH_CTRL5,
+		      IPQ5018_PHY_PCS_CDT_THRESH_CTRL5_VAL);
+	phy_write_mmd(phydev, MDIO_MMD_PCS, IPQ5018_PHY_PCS_CDT_THRESH_CTRL6,
+		      IPQ5018_PHY_PCS_CDT_THRESH_CTRL6_VAL);
+	phy_write_mmd(phydev, MDIO_MMD_PCS, IPQ5018_PHY_PCS_CDT_THRESH_CTRL7,
+		      IPQ5018_PHY_PCS_CDT_THRESH_CTRL7_VAL);
+	phy_write_mmd(phydev, MDIO_MMD_PCS, IPQ5018_PHY_PCS_CDT_THRESH_CTRL9,
+		      IPQ5018_PHY_PCS_CDT_THRESH_CTRL9_VAL);
+	phy_write_mmd(phydev, MDIO_MMD_PCS, IPQ5018_PHY_PCS_CDT_THRESH_CTRL13,
+		      IPQ5018_PHY_PCS_CDT_THRESH_CTRL13_VAL);
+	phy_write_mmd(phydev, MDIO_MMD_PCS, IPQ5018_PHY_PCS_CDT_THRESH_CTRL3,
+		      IPQ5018_PHY_PCS_NEAR_ECHO_THRESH_VAL);
+
+	/* we do all the (time consuming) work later */
+	return 0;
+}
+
+static int ipq5018_config_init(struct phy_device *phydev)
+{
+	struct ipq5018_priv *priv = phydev->priv;
+	u16 val;
+
+	/*
+	 * set LDO efuse: first temporarily store ANA_DAC_FILTER value from
+	 * debug register as it will be reset once the ANA_LDO_EFUSE register
+	 * is written to
+	 */
+	val = at803x_debug_reg_read(phydev, IPQ5018_PHY_DEBUG_ANA_DAC_FILTER);
+	at803x_debug_reg_mask(phydev, IPQ5018_PHY_DEBUG_ANA_LDO_EFUSE,
+			      IPQ5018_PHY_DEBUG_ANA_LDO_EFUSE_MASK,
+			      IPQ5018_PHY_DEBUG_ANA_LDO_EFUSE_DEFAULT);
+	at803x_debug_reg_write(phydev, IPQ5018_PHY_DEBUG_ANA_DAC_FILTER, val);
+
+	/* set 8023AZ EEE TX and RX timer values */
+	phy_write_mmd(phydev, MDIO_MMD_PCS, IPQ5018_PHY_PCS_EEE_TX_TIMER,
+		      IPQ5018_PHY_PCS_EEE_TX_TIMER_VAL);
+	phy_write_mmd(phydev, MDIO_MMD_PCS, IPQ5018_PHY_PCS_EEE_RX_TIMER,
+		      IPQ5018_PHY_PCS_EEE_RX_TIMER_VAL);
+
+	/* set MSE threshold values */
+	phy_write_mmd(phydev, MDIO_MMD_PMAPMD, IPQ5018_PHY_MMD1_MSE_THRESH1,
+		      IPQ5018_PHY_MMD1_MSE_THRESH1_VAL);
+	phy_write_mmd(phydev, MDIO_MMD_PMAPMD, IPQ5018_PHY_MMD1_MSE_THRESH2,
+		      IPQ5018_PHY_MMD1_MSE_THRESH2_VAL);
+
+	/* PHY DAC values are optional and only set in a PHY to PHY link architecture */
+	if (priv->set_short_cable_dac) {
+		/* setting MDAC (Multi-level Digital-to-Analog Converter) in MMD1 */
+		phy_modify_mmd(phydev, MDIO_MMD_PMAPMD, IPQ5018_PHY_MMD1_MDAC,
+			       IPQ5018_PHY_DAC_MASK, IPQ5018_PHY_MMD1_MDAC_VAL);
+
+		/* setting EDAC (Error-detection and Correction) in debug register */
+		at803x_debug_reg_mask(phydev, IPQ5018_PHY_DEBUG_EDAC,
+				      IPQ5018_PHY_DAC_MASK, IPQ5018_PHY_DEBUG_EDAC_VAL);
+	}
+
+	return 0;
+}
+
+static void ipq5018_link_change_notify(struct phy_device *phydev)
+{
+	/*
+	 * Reset the FIFO buffer upon link disconnects to clear any residual data
+	 * which may cause issues with the FIFO which it cannot recover from.
+	 */
+	mdiobus_modify_changed(phydev->mdio.bus, phydev->mdio.addr,
+			       IPQ5018_PHY_FIFO_CONTROL, IPQ5018_PHY_FIFO_RESET,
+			       phydev->link ? IPQ5018_PHY_FIFO_RESET : 0);
+}
+
+static int ipq5018_probe(struct phy_device *phydev)
+{
+	struct device *dev = &phydev->mdio.dev;
+	struct ipq5018_priv *priv;
+	int ret;
+
+	priv = devm_kzalloc(dev, sizeof(*priv), GFP_KERNEL);
+	if (!priv)
+		return -ENOMEM;
+
+	priv->set_short_cable_dac = of_property_read_bool(dev->of_node,
+							  "qcom,dac-preset-short-cable");
+
+	priv->rst = devm_reset_control_array_get_exclusive(dev);
+	if (IS_ERR(priv->rst))
+		return dev_err_probe(dev, PTR_ERR(priv->rst),
+				     "failed to acquire reset\n");
+
+	ret = reset_control_reset(priv->rst);
+	if (ret)
+		return dev_err_probe(dev, ret, "failed to reset\n");
+
+	phydev->priv = priv;
+
+	return 0;
+}
+
 static struct phy_driver at803x_driver[] = {
 {
 	/* Qualcomm Atheros AR8035 */
@@ -1078,6 +1231,19 @@ static struct phy_driver at803x_driver[] = {
 	.read_status		= at803x_read_status,
 	.soft_reset		= genphy_soft_reset,
 	.config_aneg		= at803x_config_aneg,
+}, {
+	PHY_ID_MATCH_EXACT(IPQ5018_PHY_ID),
+	.name			= "Qualcomm Atheros IPQ5018 internal PHY",
+	.flags			= PHY_IS_INTERNAL | PHY_POLL_CABLE_TEST,
+	.probe			= ipq5018_probe,
+	.config_init		= ipq5018_config_init,
+	.link_change_notify	= ipq5018_link_change_notify,
+	.read_status		= at803x_read_status,
+	.config_intr		= at803x_config_intr,
+	.handle_interrupt	= at803x_handle_interrupt,
+	.cable_test_start	= ipq5018_cable_test_start,
+	.cable_test_get_status	= qca808x_cable_test_get_status,
+	.soft_reset		= genphy_soft_reset,
 }, {
 	/* Qualcomm Atheros QCA9561 */
 	PHY_ID_MATCH_EXACT(QCA9561_PHY_ID),
@@ -1104,6 +1270,7 @@ static const struct mdio_device_id __maybe_unused atheros_tbl[] = {
 	{ PHY_ID_MATCH_EXACT(ATH8032_PHY_ID) },
 	{ PHY_ID_MATCH_EXACT(ATH8035_PHY_ID) },
 	{ PHY_ID_MATCH_EXACT(ATH9331_PHY_ID) },
+	{ PHY_ID_MATCH_EXACT(IPQ5018_PHY_ID) },
 	{ PHY_ID_MATCH_EXACT(QCA9561_PHY_ID) },
 	{ }
 };

-- 
2.49.0

Re: [PATCH RESEND net-next v5 0/2] Add support for the IPQ5018 Internal GE PHY

[patchwork-bot+netdevbpf]

Hello:

This series was applied to netdev/net-next.git (main)
by Jakub Kicinski <kuba@kernel.org>:

On Fri, 13 Jun 2025 05:55:06 +0400 you wrote:
> The IPQ5018 SoC contains an internal Gigabit Ethernet PHY with its
> output pins that provide an MDI interface to either an external switch
> in a PHY to PHY link architecture or directly to an attached RJ45
> connector.
> 
> The PHY supports 10BASE-T/100BASE-TX/1000BASE-T link modes in SGMII
> interface mode, CDT, auto-negotiation and 802.3az EEE.
> 
> [...]

Here is the summary with links:
  - [RESEND,net-next,v5,1/2] dt-bindings: net: qca,ar803x: Add IPQ5018 Internal GE PHY support
    https://git.kernel.org/netdev/net-next/c/82eaf94d69fc
  - [RESEND,net-next,v5,2/2] net: phy: qcom: at803x: Add Qualcomm IPQ5018 Internal PHY support
    https://git.kernel.org/netdev/net-next/c/d46502279a11

You are awesome, thank you!
-- 
Deet-doot-dot, I am a bot.
https://korg.docs.kernel.org/patchwork/pwbot.html