linux-kernel.vger.kernel.org archive mirror
 help / color / mirror / Atom feed
* [PATCH V2 net-next] net: phy: motorcomm: Add support for PHY LEDs on YT8521
@ 2025-08-13 12:45 Jijie Shao
  2025-08-14 23:33 ` Andrew Lunn
  2025-08-15  0:40 ` patchwork-bot+netdevbpf
  0 siblings, 2 replies; 3+ messages in thread
From: Jijie Shao @ 2025-08-13 12:45 UTC (permalink / raw)
  To: davem, edumazet, kuba, pabeni, andrew+netdev, horms, Frank.Sae,
	hkallweit1, linux
  Cc: shenjian15, liuyonglong, chenhao418, jonathan.cameron,
	shameerali.kolothum.thodi, salil.mehta, heiko, netdev,
	linux-kernel, shaojijie

Add minimal LED controller driver supporting
the most common uses with the 'netdev' trigger.

Signed-off-by: Jijie Shao <shaojijie@huawei.com>
Tested-by: Heiko Stuebner <heiko@sntech.de>
---
ChangeLog:
V1 -> V2:
  - Replace set_bit() with __set_bit(), suggested by Russell.
  - Optimize the names of some macro definitions, suggested by Andrew.
  V1: https://lore.kernel.org/all/20250716100041.2833168-2-shaojijie@huawei.com/
  
  note: support for ACPI will be sent separately.
  Link: https://lore.kernel.org/all/aHeEwZaqUd0kNdUQ@shell.armlinux.org.uk/
---
 drivers/net/phy/motorcomm.c | 117 ++++++++++++++++++++++++++++++++++++
 1 file changed, 117 insertions(+)

diff --git a/drivers/net/phy/motorcomm.c b/drivers/net/phy/motorcomm.c
index 0e91f5d1a4fd..a3593e663059 100644
--- a/drivers/net/phy/motorcomm.c
+++ b/drivers/net/phy/motorcomm.c
@@ -213,6 +213,20 @@
 #define YT8521_RC1R_RGMII_2_100_NS		14
 #define YT8521_RC1R_RGMII_2_250_NS		15
 
+/* LED CONFIG */
+#define YT8521_MAX_LEDS				3
+#define YT8521_LED0_CFG_REG			0xA00C
+#define YT8521_LED1_CFG_REG			0xA00D
+#define YT8521_LED2_CFG_REG			0xA00E
+#define YT8521_LED_ACT_BLK_IND			BIT(13)
+#define YT8521_LED_FDX_ON_EN			BIT(12)
+#define YT8521_LED_HDX_ON_EN			BIT(11)
+#define YT8521_LED_TXACT_BLK_EN			BIT(10)
+#define YT8521_LED_RXACT_BLK_EN			BIT(9)
+#define YT8521_LED_1000_ON_EN			BIT(6)
+#define YT8521_LED_100_ON_EN			BIT(5)
+#define YT8521_LED_10_ON_EN			BIT(4)
+
 #define YTPHY_MISC_CONFIG_REG			0xA006
 #define YTPHY_MCR_FIBER_SPEED_MASK		BIT(0)
 #define YTPHY_MCR_FIBER_1000BX			(0x1 << 0)
@@ -1681,6 +1695,106 @@ static int yt8521_config_init(struct phy_device *phydev)
 	return phy_restore_page(phydev, old_page, ret);
 }
 
+static const unsigned long supported_trgs = (BIT(TRIGGER_NETDEV_FULL_DUPLEX) |
+					     BIT(TRIGGER_NETDEV_HALF_DUPLEX) |
+					     BIT(TRIGGER_NETDEV_LINK)        |
+					     BIT(TRIGGER_NETDEV_LINK_10)     |
+					     BIT(TRIGGER_NETDEV_LINK_100)    |
+					     BIT(TRIGGER_NETDEV_LINK_1000)   |
+					     BIT(TRIGGER_NETDEV_RX)          |
+					     BIT(TRIGGER_NETDEV_TX));
+
+static int yt8521_led_hw_is_supported(struct phy_device *phydev, u8 index,
+				      unsigned long rules)
+{
+	if (index >= YT8521_MAX_LEDS)
+		return -EINVAL;
+
+	/* All combinations of the supported triggers are allowed */
+	if (rules & ~supported_trgs)
+		return -EOPNOTSUPP;
+
+	return 0;
+}
+
+static int yt8521_led_hw_control_set(struct phy_device *phydev, u8 index,
+				     unsigned long rules)
+{
+	u16 val = 0;
+
+	if (index >= YT8521_MAX_LEDS)
+		return -EINVAL;
+
+	if (test_bit(TRIGGER_NETDEV_LINK, &rules)) {
+		val |= YT8521_LED_10_ON_EN;
+		val |= YT8521_LED_100_ON_EN;
+		val |= YT8521_LED_1000_ON_EN;
+	}
+
+	if (test_bit(TRIGGER_NETDEV_LINK_10, &rules))
+		val |= YT8521_LED_10_ON_EN;
+
+	if (test_bit(TRIGGER_NETDEV_LINK_100, &rules))
+		val |= YT8521_LED_100_ON_EN;
+
+	if (test_bit(TRIGGER_NETDEV_LINK_1000, &rules))
+		val |= YT8521_LED_1000_ON_EN;
+
+	if (test_bit(TRIGGER_NETDEV_FULL_DUPLEX, &rules))
+		val |= YT8521_LED_HDX_ON_EN;
+
+	if (test_bit(TRIGGER_NETDEV_HALF_DUPLEX, &rules))
+		val |= YT8521_LED_FDX_ON_EN;
+
+	if (test_bit(TRIGGER_NETDEV_TX, &rules) ||
+	    test_bit(TRIGGER_NETDEV_RX, &rules))
+		val |= YT8521_LED_ACT_BLK_IND;
+
+	if (test_bit(TRIGGER_NETDEV_TX, &rules))
+		val |= YT8521_LED_TXACT_BLK_EN;
+
+	if (test_bit(TRIGGER_NETDEV_RX, &rules))
+		val |= YT8521_LED_RXACT_BLK_EN;
+
+	return ytphy_write_ext(phydev, YT8521_LED0_CFG_REG + index, val);
+}
+
+static int yt8521_led_hw_control_get(struct phy_device *phydev, u8 index,
+				     unsigned long *rules)
+{
+	int val;
+
+	if (index >= YT8521_MAX_LEDS)
+		return -EINVAL;
+
+	val = ytphy_read_ext(phydev, YT8521_LED0_CFG_REG + index);
+	if (val < 0)
+		return val;
+
+	if (val & YT8521_LED_TXACT_BLK_EN || val & YT8521_LED_ACT_BLK_IND)
+		__set_bit(TRIGGER_NETDEV_TX, rules);
+
+	if (val & YT8521_LED_RXACT_BLK_EN || val & YT8521_LED_ACT_BLK_IND)
+		__set_bit(TRIGGER_NETDEV_RX, rules);
+
+	if (val & YT8521_LED_FDX_ON_EN)
+		__set_bit(TRIGGER_NETDEV_FULL_DUPLEX, rules);
+
+	if (val & YT8521_LED_HDX_ON_EN)
+		__set_bit(TRIGGER_NETDEV_HALF_DUPLEX, rules);
+
+	if (val & YT8521_LED_1000_ON_EN)
+		__set_bit(TRIGGER_NETDEV_LINK_1000, rules);
+
+	if (val & YT8521_LED_100_ON_EN)
+		__set_bit(TRIGGER_NETDEV_LINK_100, rules);
+
+	if (val & YT8521_LED_10_ON_EN)
+		__set_bit(TRIGGER_NETDEV_LINK_10, rules);
+
+	return 0;
+}
+
 static int yt8531_config_init(struct phy_device *phydev)
 {
 	struct device_node *node = phydev->mdio.dev.of_node;
@@ -2920,6 +3034,9 @@ static struct phy_driver motorcomm_phy_drvs[] = {
 		.soft_reset	= yt8521_soft_reset,
 		.suspend	= yt8521_suspend,
 		.resume		= yt8521_resume,
+		.led_hw_is_supported = yt8521_led_hw_is_supported,
+		.led_hw_control_set = yt8521_led_hw_control_set,
+		.led_hw_control_get = yt8521_led_hw_control_get,
 	},
 	{
 		PHY_ID_MATCH_EXACT(PHY_ID_YT8531),
-- 
2.33.0


^ permalink raw reply related	[flat|nested] 3+ messages in thread

* Re: [PATCH V2 net-next] net: phy: motorcomm: Add support for PHY LEDs on YT8521
  2025-08-13 12:45 [PATCH V2 net-next] net: phy: motorcomm: Add support for PHY LEDs on YT8521 Jijie Shao
@ 2025-08-14 23:33 ` Andrew Lunn
  2025-08-15  0:40 ` patchwork-bot+netdevbpf
  1 sibling, 0 replies; 3+ messages in thread
From: Andrew Lunn @ 2025-08-14 23:33 UTC (permalink / raw)
  To: Jijie Shao
  Cc: davem, edumazet, kuba, pabeni, andrew+netdev, horms, Frank.Sae,
	hkallweit1, linux, shenjian15, liuyonglong, chenhao418,
	jonathan.cameron, shameerali.kolothum.thodi, salil.mehta, heiko,
	netdev, linux-kernel

On Wed, Aug 13, 2025 at 08:45:42PM +0800, Jijie Shao wrote:
> Add minimal LED controller driver supporting
> the most common uses with the 'netdev' trigger.
> 
> Signed-off-by: Jijie Shao <shaojijie@huawei.com>
> Tested-by: Heiko Stuebner <heiko@sntech.de>

Reviewed-by: Andrew Lunn <andrew@lunn.ch>

    Andrew

^ permalink raw reply	[flat|nested] 3+ messages in thread

* Re: [PATCH V2 net-next] net: phy: motorcomm: Add support for PHY LEDs on YT8521
  2025-08-13 12:45 [PATCH V2 net-next] net: phy: motorcomm: Add support for PHY LEDs on YT8521 Jijie Shao
  2025-08-14 23:33 ` Andrew Lunn
@ 2025-08-15  0:40 ` patchwork-bot+netdevbpf
  1 sibling, 0 replies; 3+ messages in thread
From: patchwork-bot+netdevbpf @ 2025-08-15  0:40 UTC (permalink / raw)
  To: Jijie Shao
  Cc: davem, edumazet, kuba, pabeni, andrew+netdev, horms, Frank.Sae,
	hkallweit1, linux, shenjian15, liuyonglong, chenhao418,
	jonathan.cameron, shameerali.kolothum.thodi, salil.mehta, heiko,
	netdev, linux-kernel

Hello:

This patch was applied to netdev/net-next.git (main)
by Jakub Kicinski <kuba@kernel.org>:

On Wed, 13 Aug 2025 20:45:42 +0800 you wrote:
> Add minimal LED controller driver supporting
> the most common uses with the 'netdev' trigger.
> 
> Signed-off-by: Jijie Shao <shaojijie@huawei.com>
> Tested-by: Heiko Stuebner <heiko@sntech.de>
> ---
> ChangeLog:
> V1 -> V2:
>   - Replace set_bit() with __set_bit(), suggested by Russell.
>   - Optimize the names of some macro definitions, suggested by Andrew.
>   V1: https://lore.kernel.org/all/20250716100041.2833168-2-shaojijie@huawei.com/
> 
> [...]

Here is the summary with links:
  - [V2,net-next] net: phy: motorcomm: Add support for PHY LEDs on YT8521
    https://git.kernel.org/netdev/net-next/c/355b82c54c12

You are awesome, thank you!
-- 
Deet-doot-dot, I am a bot.
https://korg.docs.kernel.org/patchwork/pwbot.html



^ permalink raw reply	[flat|nested] 3+ messages in thread

end of thread, other threads:[~2025-08-15  0:40 UTC | newest]

Thread overview: 3+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
2025-08-13 12:45 [PATCH V2 net-next] net: phy: motorcomm: Add support for PHY LEDs on YT8521 Jijie Shao
2025-08-14 23:33 ` Andrew Lunn
2025-08-15  0:40 ` patchwork-bot+netdevbpf

This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).