[PATCH v2 0/7] arm64: dts: ti: k3-am62: Add wakeup-sources for low power modes

[PATCH v2 0/7] arm64: dts: ti: k3-am62: Add wakeup-sources for low power modes

[Markus Schneider-Pargmann]

Hi,

This series adds devicetree changes needed for Partial-IO support
on TI am62, am62a, and am62p SoCs. It defines system states for various
low power modes and configures the wakeup-sources for devices in the CANUART
group. Depending on the SoC and board details, some low power modes may not
be available, so the wakeup-sources are described in the board files.
The series also adds the necessary pinctrl settings required for proper
wakeup functionality.

Partial-IO Overview
------------------
Partial-IO is a low power system state in which nearly everything is
turned off except the pins of the CANUART group (mcu_mcan0, mcu_mcan1,
wkup_uart0 and mcu_uart0). These devices can trigger a wakeup of the system
on pin activity. Note that this does not resume the system as the DDR is
off as well. So this state can be considered a power-off state with wakeup
capabilities.

A documentation can also be found in section 6.2.4 in the TRM:
  https://www.ti.com/lit/pdf/spruiv7

Implementation Details
----------------------
The complete Partial-IO feature requires three coordinated series, each handling
a different aspect of the implementation:

1. m_can driver series: Implements device-specific wakeup functionality
    for m_can devices, allowing them to be set as wakeup sources.
    https://gitlab.baylibre.com/msp8/linux/-/tree/topic/mcan-wakeup-source/v6.17?ref_type=heads
    https://lore.kernel.org/r/20250812-topic-mcan-wakeup-source-v6-12-v8-0-6972a810d63b@baylibre.com

2. This series (devicetree): Defines system states and wakeup sources in the
    devicetree for am62, am62a and am62p.

3. TI-SCI firmware series: Implements the firmware interface to enter Partial-IO
    mode when appropriate wakeup sources are enabled.
    https://gitlab.baylibre.com/msp8/linux/-/tree/topic/tisci-partialio/v6.17?ref_type=heads

Devicetree Bindings
-------------------
This series depends on the dt-schema pull request that adds bindings for
system-idle-states and updates the binding for wakeup-source:
  https://github.com/devicetree-org/dt-schema/pull/150

This is merged now in upstream dt-schema. These new bindings allow us to
define the system states and reference them from device wakeup-source
properties.

Testing
-------
A test branch is available here that includes all patches required to
test Partial-IO:

https://gitlab.baylibre.com/msp8/linux/-/tree/integration/am62-partialio/v6.17?ref_type=heads

After enabling Wake-on-LAN the system can be powered off and will enter
the Partial-IO state in which it can be woken up by activity on the
specific pins:
    ethtool -s can0 wol p
    ethtool -s can1 wol p
    poweroff

I tested these patches on am62-lp-sk.

Best,
Markus

Previous versions
-----------------
 - Link to v1: https://lore.kernel.org/r/20250421-topic-am62-dt-partialio-v6-15-v1-0-6ced30aafddb@baylibre.com
 - As part of the series "firmware: ti_sci: Partial-IO support"
   https://lore.kernel.org/r/20250306-topic-am62-partialio-v6-12-b4-v5-0-f9323d3744a2@baylibre.com

Changes in v2:
 - Combine k3-am62a7-sk.dts devicetree nodes with existing ones
 - Combine k3-am62p5-sk.dts devicetree nodes with existing ones
 - Update the idle-state-name properties to the new names from the
   dt-schema
 - Rebase to 6.17-rc1

Signed-off-by: Markus Schneider-Pargmann <msp@baylibre.com>
---
Markus Schneider-Pargmann (7):
      arm64: dts: ti: k3-pinctrl: Add WKUP_EN flag
      arm64: dts: ti: k3-am62: Define possible system states
      arm64: dts: ti: k3-am62a: Define possible system states
      arm64: dts: ti: k3-am62p: Define possible system states
      arm64: dts: ti: k3-am62-lp-sk: Set wakeup-source system-states
      arm64: dts: ti: k3-am62a7-sk: Set wakeup-source system-states
      arm64: dts: ti: k3-am62p5-sk: Set wakeup-source system-states

 arch/arm64/boot/dts/ti/k3-am62-lp-sk.dts | 60 +++++++++++++++++++++++++++
 arch/arm64/boot/dts/ti/k3-am62.dtsi      | 22 ++++++++++
 arch/arm64/boot/dts/ti/k3-am62a.dtsi     | 27 ++++++++++++
 arch/arm64/boot/dts/ti/k3-am62a7-sk.dts  | 71 ++++++++++++++++++++++++++++++++
 arch/arm64/boot/dts/ti/k3-am62p.dtsi     | 27 ++++++++++++
 arch/arm64/boot/dts/ti/k3-am62p5-sk.dts  | 71 ++++++++++++++++++++++++++++++++
 arch/arm64/boot/dts/ti/k3-pinctrl.h      |  2 +
 7 files changed, 280 insertions(+)
---
base-commit: 062b3e4a1f880f104a8d4b90b767788786aa7b78
change-id: 20250415-topic-am62-dt-partialio-v6-15-327dd1ff17da
prerequisite-change-id: 20241009-topic-mcan-wakeup-source-v6-12-8c1d69931bd8:v8
prerequisite-patch-id: 02b7142f56c849c9a3faab2d2871805febd647aa
prerequisite-patch-id: 830b339ea452edd750b04f719da91e721be630cb
prerequisite-patch-id: 2c9142d2bc47e64c49b7b8a7ca20a62a0be14870
prerequisite-patch-id: f7652a616dca17fd5e4a7e5cba59de6a6a36079f

Best regards,
-- 
Markus Schneider-Pargmann <msp@baylibre.com>

[PATCH v2 1/7] arm64: dts: ti: k3-pinctrl: Add WKUP_EN flag

[Markus Schneider-Pargmann]

WKUP_EN is a flag to enable pin wakeup. Any activity will wakeup the SoC
in that case.

Signed-off-by: Markus Schneider-Pargmann <msp@baylibre.com>
---
 arch/arm64/boot/dts/ti/k3-pinctrl.h | 2 ++
 1 file changed, 2 insertions(+)

diff --git a/arch/arm64/boot/dts/ti/k3-pinctrl.h b/arch/arm64/boot/dts/ti/k3-pinctrl.h
index c0f09be8d3f94a70812b66c3f91626aac35f4026..d3b0ecdf1a4a4de25ee6121ec9e62d1c7df26eb9 100644
--- a/arch/arm64/boot/dts/ti/k3-pinctrl.h
+++ b/arch/arm64/boot/dts/ti/k3-pinctrl.h
@@ -19,6 +19,7 @@
 #define DS_OUT_VAL_SHIFT	(26)
 #define DS_PULLUD_EN_SHIFT	(27)
 #define DS_PULLTYPE_SEL_SHIFT	(28)
+#define WKUP_EN_SHIFT		(29)
 
 /* Schmitt trigger configuration */
 #define ST_DISABLE		(0 << ST_EN_SHIFT)
@@ -65,6 +66,7 @@
 #define PIN_DS_PULLUD_DISABLE		(1 << DS_PULLUD_EN_SHIFT)
 #define PIN_DS_PULL_DOWN		(0 << DS_PULLTYPE_SEL_SHIFT)
 #define PIN_DS_PULL_UP			(1 << DS_PULLTYPE_SEL_SHIFT)
+#define WKUP_EN				(1 << WKUP_EN_SHIFT)
 
 /* Default mux configuration for gpio-ranges to use with pinctrl */
 #define PIN_GPIO_RANGE_IOPAD	(PIN_INPUT | 7)

-- 
2.50.1

[PATCH v2 2/7] arm64: dts: ti: k3-am62: Define possible system states

[Markus Schneider-Pargmann]

Add the system states that are available on am62 SoCs.

Signed-off-by: Markus Schneider-Pargmann <msp@baylibre.com>
---
 arch/arm64/boot/dts/ti/k3-am62.dtsi | 22 ++++++++++++++++++++++
 1 file changed, 22 insertions(+)

diff --git a/arch/arm64/boot/dts/ti/k3-am62.dtsi b/arch/arm64/boot/dts/ti/k3-am62.dtsi
index 59f6dff552ed40e4ac0f9c7077aa25d68d3b5283..b08b7062060ca12ecae83917a831ee779f1a288f 100644
--- a/arch/arm64/boot/dts/ti/k3-am62.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-am62.dtsi
@@ -46,6 +46,28 @@ pmu: pmu {
 		interrupts = <GIC_PPI 7 IRQ_TYPE_LEVEL_HIGH>;
 	};
 
+	system-idle-states {
+		system_partial_io: system-partial-io {
+			compatible = "system-idle-state";
+			idle-state-name = "off-wake";
+		};
+
+		system_deep_sleep: system-deep-sleep {
+			compatible = "system-idle-state";
+			idle-state-name = "mem";
+		};
+
+		system_mcu_only: system-mcu-only {
+			compatible = "system-idle-state";
+			idle-state-name = "mem-mcu-active";
+		};
+
+		system_standby: system-standby {
+			compatible = "system-idle-state";
+			idle-state-name = "standby";
+		};
+	};
+
 	cbass_main: bus@f0000 {
 		bootph-all;
 		compatible = "simple-bus";

-- 
2.50.1

[PATCH v2 3/7] arm64: dts: ti: k3-am62a: Define possible system states

[Markus Schneider-Pargmann]

Add the system states that are available on am62a SoCs.

Signed-off-by: Markus Schneider-Pargmann <msp@baylibre.com>
---
 arch/arm64/boot/dts/ti/k3-am62a.dtsi | 27 +++++++++++++++++++++++++++
 1 file changed, 27 insertions(+)

diff --git a/arch/arm64/boot/dts/ti/k3-am62a.dtsi b/arch/arm64/boot/dts/ti/k3-am62a.dtsi
index 4d79b3e9486af18b8813a8980a57937669ff6095..31b2de035f0f748e34b8919f90251aa0551d9b32 100644
--- a/arch/arm64/boot/dts/ti/k3-am62a.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-am62a.dtsi
@@ -46,6 +46,33 @@ pmu: pmu {
 		interrupts = <GIC_PPI 7 IRQ_TYPE_LEVEL_HIGH>;
 	};
 
+	system-idle-states {
+		system_partial_io: system-partial-io {
+			compatible = "system-idle-state";
+			idle-state-name = "off-wake";
+		};
+
+		system_io_ddr: system-io-ddr {
+			compatible = "system-idle-state";
+			idle-state-name = "mem-deep";
+		};
+
+		system_deep_sleep: system-deep-sleep {
+			compatible = "system-idle-state";
+			idle-state-name = "mem";
+		};
+
+		system_mcu_only: system-mcu-only {
+			compatible = "system-idle-state";
+			idle-state-name = "mem-mcu-active";
+		};
+
+		system_standby: system-standby {
+			compatible = "system-idle-state";
+			idle-state-name = "standby";
+		};
+	};
+
 	cbass_main: bus@f0000 {
 		compatible = "simple-bus";
 		#address-cells = <2>;

-- 
2.50.1

[PATCH v2 4/7] arm64: dts: ti: k3-am62p: Define possible system states

[Markus Schneider-Pargmann]

Add the system states that are available on am62p SoCs.

Signed-off-by: Markus Schneider-Pargmann <msp@baylibre.com>
---
 arch/arm64/boot/dts/ti/k3-am62p.dtsi | 27 +++++++++++++++++++++++++++
 1 file changed, 27 insertions(+)

diff --git a/arch/arm64/boot/dts/ti/k3-am62p.dtsi b/arch/arm64/boot/dts/ti/k3-am62p.dtsi
index 75a15c368c11b068430362fe0b8d2d9ecc052588..c69e16f16c835489f2bc5cba158235ab955347e3 100644
--- a/arch/arm64/boot/dts/ti/k3-am62p.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-am62p.dtsi
@@ -44,6 +44,33 @@ pmu: pmu {
 		interrupts = <GIC_PPI 7 IRQ_TYPE_LEVEL_HIGH>;
 	};
 
+	system-idle-states {
+		system_partial_io: system-partial-io {
+			compatible = "system-idle-state";
+			idle-state-name = "off-wake";
+		};
+
+		system_io_ddr: system-io-ddr {
+			compatible = "system-idle-state";
+			idle-state-name = "mem-deep";
+		};
+
+		system_deep_sleep: system-deep-sleep {
+			compatible = "system-idle-state";
+			idle-state-name = "mem";
+		};
+
+		system_mcu_only: system-mcu-only {
+			compatible = "system-idle-state";
+			idle-state-name = "mem-mcu-active";
+		};
+
+		system_standby: system-standby {
+			compatible = "system-idle-state";
+			idle-state-name = "standby";
+		};
+	};
+
 	cbass_main: bus@f0000 {
 		compatible = "simple-bus";
 		#address-cells = <2>;

-- 
2.50.1

[PATCH v2 5/7] arm64: dts: ti: k3-am62-lp-sk: Set wakeup-source system-states

[Markus Schneider-Pargmann]

The CANUART pins of mcu_mcan0, mcu_mcan1, mcu_uart0 and wkup_uart0 are
powered during Partial-IO and IO+DDR and are capable of waking up the
system in these states. Specify the states in which these units can do a
wakeup on this board.

Note that the UARTs are not capable of wakeup in Partial-IO because of
of a UART mux on the board not being powered during Partial-IO. As
IO+DDR is not supported on am62, the UARTs are not added in this patch.

Add pincontrol definitions for mcu_mcan0 and mcu_mcan1 for wakeup from
Partial-IO. Add these as wakeup pinctrl entries for both devices.

Signed-off-by: Markus Schneider-Pargmann <msp@baylibre.com>
---
 arch/arm64/boot/dts/ti/k3-am62-lp-sk.dts | 60 ++++++++++++++++++++++++++++++++
 1 file changed, 60 insertions(+)

diff --git a/arch/arm64/boot/dts/ti/k3-am62-lp-sk.dts b/arch/arm64/boot/dts/ti/k3-am62-lp-sk.dts
index 4609f366006e4cdf0c162f72634ce90623f60a90..0314f857ea05acc4ffc62bccb5184e58d19a6103 100644
--- a/arch/arm64/boot/dts/ti/k3-am62-lp-sk.dts
+++ b/arch/arm64/boot/dts/ti/k3-am62-lp-sk.dts
@@ -268,3 +268,63 @@ &main_gpio1 {
 &gpmc0 {
 	ranges = <0 0 0x00 0x51000000 0x01000000>; /* CS0 space. Min partition = 16MB */
 };
+
+&mcu_mcan0 {
+	pinctrl-names = "default", "wakeup";
+	pinctrl-0 = <&mcu_mcan0_tx_pins_default>, <&mcu_mcan0_rx_pins_default>;
+	pinctrl-1 = <&mcu_mcan0_tx_pins_default>, <&mcu_mcan0_rx_pins_wakeup>;
+	wakeup-source = <&system_partial_io>,
+			<&system_deep_sleep>,
+			<&system_mcu_only>,
+			<&system_standby>;
+	status = "okay";
+};
+
+&mcu_mcan1 {
+	pinctrl-names = "default", "wakeup";
+	pinctrl-0 = <&mcu_mcan1_tx_pins_default>, <&mcu_mcan1_rx_pins_default>;
+	pinctrl-1 = <&mcu_mcan1_tx_pins_default>, <&mcu_mcan1_rx_pins_wakeup>;
+	wakeup-source = <&system_partial_io>,
+			<&system_deep_sleep>,
+			<&system_mcu_only>,
+			<&system_standby>;
+	status = "okay";
+};
+
+&mcu_pmx0 {
+	mcu_mcan0_tx_pins_default: mcu-mcan0-tx-default-pins {
+		pinctrl-single,pins = <
+			AM62X_IOPAD(0x034, PIN_OUTPUT, 0) /* (D6) MCU_MCAN0_TX */
+		>;
+	};
+
+	mcu_mcan0_rx_pins_default: mcu-mcan0-rx-default-pins {
+		pinctrl-single,pins = <
+			AM62X_IOPAD(0x038, PIN_INPUT, 0) /* (B3) MCU_MCAN0_RX */
+		>;
+	};
+
+	mcu_mcan0_rx_pins_wakeup: mcu-mcan0-rx-wakeup-pins {
+		pinctrl-single,pins = <
+			AM62X_IOPAD(0x038, PIN_INPUT | WKUP_EN, 0) /* (B3) MCU_MCAN0_RX */
+		>;
+	};
+
+	mcu_mcan1_tx_pins_default: mcu-mcan1-tx-default-pins {
+		pinctrl-single,pins = <
+			AM62X_IOPAD(0x03c, PIN_OUTPUT, 0) /* (E5) MCU_MCAN1_TX */
+		>;
+	};
+
+	mcu_mcan1_rx_pins_default: mcu-mcan1-rx-default-pins {
+		pinctrl-single,pins = <
+			AM62X_IOPAD(0x040, PIN_INPUT, 0) /* (D4) MCU_MCAN1_RX */
+		>;
+	};
+
+	mcu_mcan1_rx_pins_wakeup: mcu-mcan1-rx-wakeup-pins {
+		pinctrl-single,pins = <
+			AM62X_IOPAD(0x040, PIN_INPUT | WKUP_EN, 0) /* (D4) MCU_MCAN1_RX */
+		>;
+	};
+};

-- 
2.50.1

[PATCH v2 6/7] arm64: dts: ti: k3-am62a7-sk: Set wakeup-source system-states

[Markus Schneider-Pargmann]

The CANUART pins of mcu_mcan0, mcu_mcan1, mcu_uart0 and wkup_uart0 are
powered during Partial-IO and IO+DDR and are capable of waking up the
system in these states. Specify the states in which these units can do a
wakeup on this board.

Note that the UARTs are not capable of wakeup in Partial-IO because of
of a UART mux on the board not being powered during Partial-IO.

Add pincontrol definitions for mcu_mcan0 and mcu_mcan1 for wakeup from
Partial-IO. Add these as wakeup pinctrl entries for both devices.

Signed-off-by: Markus Schneider-Pargmann <msp@baylibre.com>

- Combine k3-am62a7-sk.dts devicetree nodes
---
 arch/arm64/boot/dts/ti/k3-am62a7-sk.dts | 71 +++++++++++++++++++++++++++++++++
 1 file changed, 71 insertions(+)

diff --git a/arch/arm64/boot/dts/ti/k3-am62a7-sk.dts b/arch/arm64/boot/dts/ti/k3-am62a7-sk.dts
index bceead5e288e6d78c671baf0afabd1a9aa23fbee..55cab49f26382f08e2cc93d17afc424af8c59caa 100644
--- a/arch/arm64/boot/dts/ti/k3-am62a7-sk.dts
+++ b/arch/arm64/boot/dts/ti/k3-am62a7-sk.dts
@@ -257,6 +257,10 @@ AM62AX_MCU_IOPAD(0x0030, PIN_OUTPUT, 0) /* (C8) WKUP_UART0_RTSn */
 &wkup_uart0 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&wkup_uart0_pins_default>;
+	wakeup-source = <&system_io_ddr>,
+			<&system_deep_sleep>,
+			<&system_mcu_only>,
+			<&system_standby>;
 	status = "reserved";
 };
 
@@ -450,6 +454,42 @@ pmic_irq_pins_default: pmic-irq-default-pins {
 			AM62AX_MCU_IOPAD(0x000, PIN_INPUT, 7) /* (E11) MCU_GPIO0_0 */
 		>;
 	};
+
+	mcu_mcan0_tx_pins_default: mcu-mcan0-tx-default-pins {
+		pinctrl-single,pins = <
+			AM62X_IOPAD(0x034, PIN_OUTPUT, 0) /* (D6) MCU_MCAN0_TX */
+		>;
+	};
+
+	mcu_mcan0_rx_pins_default: mcu-mcan0-rx-default-pins {
+		pinctrl-single,pins = <
+			AM62X_IOPAD(0x038, PIN_INPUT, 0) /* (B3) MCU_MCAN0_RX */
+		>;
+	};
+
+	mcu_mcan0_rx_pins_wakeup: mcu-mcan0-rx-wakeup-pins {
+		pinctrl-single,pins = <
+			AM62X_IOPAD(0x038, PIN_INPUT | WKUP_EN, 0) /* (B3) MCU_MCAN0_RX */
+		>;
+	};
+
+	mcu_mcan1_tx_pins_default: mcu-mcan1-tx-default-pins {
+		pinctrl-single,pins = <
+			AM62X_IOPAD(0x03c, PIN_OUTPUT, 0) /* (E5) MCU_MCAN1_TX */
+		>;
+	};
+
+	mcu_mcan1_rx_pins_default: mcu-mcan1-rx-default-pins {
+		pinctrl-single,pins = <
+			AM62X_IOPAD(0x040, PIN_INPUT, 0) /* (D4) MCU_MCAN1_RX */
+		>;
+	};
+
+	mcu_mcan1_rx_pins_wakeup: mcu-mcan1-rx-wakeup-pins {
+		pinctrl-single,pins = <
+			AM62X_IOPAD(0x040, PIN_INPUT | WKUP_EN, 0) /* (D4) MCU_MCAN1_RX */
+		>;
+	};
 };
 
 &mcu_gpio0 {
@@ -935,3 +975,34 @@ AM62AX_IOPAD(0x008, PIN_INPUT, 0) /* (J24) OSPI0_DQS */
 		>;
 	};
 };
+
+&mcu_mcan0 {
+	pinctrl-names = "default", "wakeup";
+	pinctrl-0 = <&mcu_mcan0_tx_pins_default>, <&mcu_mcan0_rx_pins_default>;
+	pinctrl-1 = <&mcu_mcan0_tx_pins_default>, <&mcu_mcan0_rx_pins_wakeup>;
+	wakeup-source = <&system_partial_io>,
+			<&system_io_ddr>,
+			<&system_deep_sleep>,
+			<&system_mcu_only>,
+			<&system_standby>;
+	status = "okay";
+};
+
+&mcu_mcan1 {
+	pinctrl-names = "default", "wakeup";
+	pinctrl-0 = <&mcu_mcan1_tx_pins_default>, <&mcu_mcan1_rx_pins_default>;
+	pinctrl-1 = <&mcu_mcan1_tx_pins_default>, <&mcu_mcan1_rx_pins_wakeup>;
+	wakeup-source = <&system_partial_io>,
+			<&system_io_ddr>,
+			<&system_deep_sleep>,
+			<&system_mcu_only>,
+			<&system_standby>;
+	status = "okay";
+};
+
+&mcu_uart0 {
+	wakeup-source = <&system_io_ddr>,
+			<&system_deep_sleep>,
+			<&system_mcu_only>,
+			<&system_standby>;
+};

-- 
2.50.1

[PATCH v2 7/7] arm64: dts: ti: k3-am62p5-sk: Set wakeup-source system-states

[Markus Schneider-Pargmann]

The CANUART pins of mcu_mcan0, mcu_mcan1, mcu_uart0 and wkup_uart0 are
powered during Partial-IO and IO+DDR and are capable of waking up the
system in these states. Specify the states in which these units can do a
wakeup on this board.

Note that the UARTs are not capable of wakeup in Partial-IO because of
of a UART mux on the board not being powered during Partial-IO.

Add pincontrol definitions for mcu_mcan0 and mcu_mcan1 for wakeup from
Partial-IO. Add these as wakeup pinctrl entries for both devices.

Signed-off-by: Markus Schneider-Pargmann <msp@baylibre.com>

- Merge devicetree nodes in k3-am62p5-sk.dts
---
 arch/arm64/boot/dts/ti/k3-am62p5-sk.dts | 71 +++++++++++++++++++++++++++++++++
 1 file changed, 71 insertions(+)

diff --git a/arch/arm64/boot/dts/ti/k3-am62p5-sk.dts b/arch/arm64/boot/dts/ti/k3-am62p5-sk.dts
index 899da7896563b43021de14eda1b0058a5c6d36da..a2dffb5e243f543c90081eeacdc0758b38bd0eb9 100644
--- a/arch/arm64/boot/dts/ti/k3-am62p5-sk.dts
+++ b/arch/arm64/boot/dts/ti/k3-am62p5-sk.dts
@@ -762,12 +762,52 @@ AM62PX_MCU_IOPAD(0x028, PIN_OUTPUT, 0)	/* (D7) WKUP_UART0_TXD */
 		>;
 		bootph-all;
 	};
+
+	mcu_mcan0_tx_pins_default: mcu-mcan0-tx-default-pins {
+		pinctrl-single,pins = <
+			AM62X_IOPAD(0x034, PIN_OUTPUT, 0) /* (D6) MCU_MCAN0_TX */
+		>;
+	};
+
+	mcu_mcan0_rx_pins_default: mcu-mcan0-rx-default-pins {
+		pinctrl-single,pins = <
+			AM62X_IOPAD(0x038, PIN_INPUT, 0) /* (B3) MCU_MCAN0_RX */
+		>;
+	};
+
+	mcu_mcan0_rx_pins_wakeup: mcu-mcan0-rx-wakeup-pins {
+		pinctrl-single,pins = <
+			AM62X_IOPAD(0x038, PIN_INPUT | WKUP_EN, 0) /* (B3) MCU_MCAN0_RX */
+		>;
+	};
+
+	mcu_mcan1_tx_pins_default: mcu-mcan1-tx-default-pins {
+		pinctrl-single,pins = <
+			AM62X_IOPAD(0x03c, PIN_OUTPUT, 0) /* (E5) MCU_MCAN1_TX */
+		>;
+	};
+
+	mcu_mcan1_rx_pins_default: mcu-mcan1-rx-default-pins {
+		pinctrl-single,pins = <
+			AM62X_IOPAD(0x040, PIN_INPUT, 0) /* (D4) MCU_MCAN1_RX */
+		>;
+	};
+
+	mcu_mcan1_rx_pins_wakeup: mcu-mcan1-rx-wakeup-pins {
+		pinctrl-single,pins = <
+			AM62X_IOPAD(0x040, PIN_INPUT | WKUP_EN, 0) /* (D4) MCU_MCAN1_RX */
+		>;
+	};
 };
 
 &wkup_uart0 {
 	/* WKUP UART0 is used by DM firmware */
 	pinctrl-names = "default";
 	pinctrl-0 = <&wkup_uart0_pins_default>;
+	wakeup-source = <&system_io_ddr>,
+			<&system_deep_sleep>,
+			<&system_mcu_only>,
+			<&system_standby>;
 	status = "reserved";
 	bootph-all;
 };
@@ -808,3 +848,34 @@ &epwm1 {
 	pinctrl-0 = <&main_epwm1_pins_default>;
 	status = "okay";
 };
+
+&mcu_mcan0 {
+	pinctrl-names = "default", "wakeup";
+	pinctrl-0 = <&mcu_mcan0_tx_pins_default>, <&mcu_mcan0_rx_pins_default>;
+	pinctrl-1 = <&mcu_mcan0_tx_pins_default>, <&mcu_mcan0_rx_pins_wakeup>;
+	wakeup-source = <&system_partial_io>,
+			<&system_io_ddr>,
+			<&system_deep_sleep>,
+			<&system_mcu_only>,
+			<&system_standby>;
+	status = "okay";
+};
+
+&mcu_mcan1 {
+	pinctrl-names = "default", "wakeup";
+	pinctrl-0 = <&mcu_mcan1_tx_pins_default>, <&mcu_mcan1_rx_pins_default>;
+	pinctrl-1 = <&mcu_mcan1_tx_pins_default>, <&mcu_mcan1_rx_pins_wakeup>;
+	wakeup-source = <&system_partial_io>,
+			<&system_io_ddr>,
+			<&system_deep_sleep>,
+			<&system_mcu_only>,
+			<&system_standby>;
+	status = "okay";
+};
+
+&mcu_uart0 {
+	wakeup-source = <&system_io_ddr>,
+			<&system_deep_sleep>,
+			<&system_mcu_only>,
+			<&system_standby>;
+};

-- 
2.50.1

Re: [PATCH v2 1/7] arm64: dts: ti: k3-pinctrl: Add WKUP_EN flag

[Kendall Willis]

On 8/12/25 04:15, Markus Schneider-Pargmann wrote:
> WKUP_EN is a flag to enable pin wakeup. Any activity will wakeup the SoC
> in that case.
> 
> Signed-off-by: Markus Schneider-Pargmann <msp@baylibre.com>
> ---
>   arch/arm64/boot/dts/ti/k3-pinctrl.h | 2 ++
>   1 file changed, 2 insertions(+)
> 
> diff --git a/arch/arm64/boot/dts/ti/k3-pinctrl.h b/arch/arm64/boot/dts/ti/k3-pinctrl.h
> index c0f09be8d3f94a70812b66c3f91626aac35f4026..d3b0ecdf1a4a4de25ee6121ec9e62d1c7df26eb9 100644
> --- a/arch/arm64/boot/dts/ti/k3-pinctrl.h
> +++ b/arch/arm64/boot/dts/ti/k3-pinctrl.h
> @@ -19,6 +19,7 @@
>   #define DS_OUT_VAL_SHIFT	(26)
>   #define DS_PULLUD_EN_SHIFT	(27)
>   #define DS_PULLTYPE_SEL_SHIFT	(28)
> +#define WKUP_EN_SHIFT		(29)
>   
>   /* Schmitt trigger configuration */
>   #define ST_DISABLE		(0 << ST_EN_SHIFT)
> @@ -65,6 +66,7 @@
>   #define PIN_DS_PULLUD_DISABLE		(1 << DS_PULLUD_EN_SHIFT)
>   #define PIN_DS_PULL_DOWN		(0 << DS_PULLTYPE_SEL_SHIFT)
>   #define PIN_DS_PULL_UP			(1 << DS_PULLTYPE_SEL_SHIFT)
> +#define WKUP_EN				(1 << WKUP_EN_SHIFT)
>   
>   /* Default mux configuration for gpio-ranges to use with pinctrl */
>   #define PIN_GPIO_RANGE_IOPAD	(PIN_INPUT | 7)
> 

Reviewed-by: Kendall Willis <k-willis@ti.com>