Netmos PCI parallel card

Netmos PCI parallel card

[Igmar Palsenberg]

[-- Attachment #1: Type: TEXT/PLAIN, Size: 360 bytes --]


Hi,

Attached is a patch to make a Netmos PCI parallal port card working.

Card is a PCI card with a Netmos 9705 controller and an Atmel serial
eeprom.



	Regards,


		Igmar


-- 

--
Igmar Palsenberg
JDI Media Solutions

Jansplaats 11
6811 GB Arnhem
The Netherlands

mailto: i.palsenberg@jdimedia.nl
PGP/GPG key : http://www.jdimedia.nl/formulier/pgp/igmar

[-- Attachment #2: Type: TEXT/PLAIN, Size: 3160 bytes --]

00:00.0 Class 0600: 8086:7122 (rev 03)
	Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
	Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ >SERR- <PERR-
	Latency: 0 set

00:01.0 Class 0300: 8086:7123 (rev 03)
	Subsystem: 8086:0200
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
	Status: Cap+ 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
	Latency: 0 set
	Interrupt: pin A routed to IRQ 11
	Region 0: Memory at ec000000 (32-bit, prefetchable)
	Region 1: Memory at ffe80000 (32-bit, non-prefetchable)
	Capabilities: [dc] Power Management version 1
		Flags: PMEClk- AuxPwr- DSI+ D1- D2- PME-
		Status: D0 PME-Enable- DSel=0 DScale=0 PME-

00:1e.0 Class 0604: 8086:2418 (rev 01)
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
	Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
	Latency: 0 set
	Bus: primary=00, secondary=01, subordinate=01, sec-latency=64
	I/O behind bridge: 0000d000-0000dfff
	Memory behind bridge: ffc00000-ffcfffff
	Prefetchable memory behind bridge: e7e00000-e7efffff
	BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-

00:1f.0 Class 0601: 8086:2410 (rev 01)
	Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
	Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
	Latency: 0 set

00:1f.1 Class 0101: 8086:2411 (rev 01) (prog-if 80 [Master])
	Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
	Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
	Latency: 0 set
	Region 4: I/O ports at ffa0

00:1f.2 Class 0c03: 8086:2412 (rev 01)
	Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
	Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
	Latency: 0 set
	Interrupt: pin D routed to IRQ 5
	Region 4: I/O ports at ef80

00:1f.3 Class 0c05: 8086:2413 (rev 01)
	Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
	Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
	Interrupt: pin B routed to IRQ 10
	Region 4: I/O ports at efa0

01:05.0 Class 0200: 10ec:8029
	Subsystem: 10ec:8029
	Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
	Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
	Interrupt: pin A routed to IRQ 10
	Region 0: I/O ports at df80

01:0b.0 Class 0701: 9710:9705 (rev 01) (prog-if 02)
	Subsystem: 1000:0010
	Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
	Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
	Interrupt: pin A routed to IRQ 5
	Region 0: I/O ports at df00


[-- Attachment #3: Type: TEXT/PLAIN, Size: 1246 bytes --]

--- linux/include/linux/pci.h.orig	Thu Feb 15 11:18:43 2001
+++ linux/include/linux/pci.h	Thu Feb 15 11:52:27 2001
@@ -1268,6 +1268,9 @@
 #define PCI_DEVICE_ID_INTERPHASE_5526	0x0004
 #define PCI_DEVICE_ID_INTERPHASE_55x6	0x0005
 
+#define PCI_VENDOR_ID_NETMOS		0x9710
+#define PCI_VENDOR_ID_NETMOS_9705	0x9705
+
 /*
  * The PCI interface treats multi-function devices as independent
  * devices.  The slot/function address of each device is encoded
--- linux/drivers/misc/parport_pc.c.orig	Thu Feb 15 11:49:00 2001
+++ linux/drivers/misc/parport_pc.c	Thu Feb 15 11:53:21 2001
@@ -910,6 +910,8 @@
 		  { { 0, -1 }, } },
 		{ PCI_VENDOR_ID_OXSEMI, PCI_DEVICE_ID_OXSEMI_12PCI840, 1,
 		  { { 0, 1 }, } },
+		{ PCI_VENDOR_ID_NETMOS, PCI_DEVICE_ID_NETMOS_9705, 1, 
+		  { { 0, -1 }, } },
 		{ 0, }
 	};
 
--- linux/drivers/pci/oldproc.c.orig	Thu Feb 15 11:30:36 2001
+++ linux/drivers/pci/oldproc.c	Thu Feb 15 11:30:06 2001
@@ -947,6 +947,7 @@
 	      case PCI_VENDOR_ID_TIGERJET:	return "TigerJet";
 	      case PCI_VENDOR_ID_ARK:		return "ARK Logic";
 	      case PCI_VENDOR_ID_SYSKONNECT:	return "SysKonnect";
+	      case PCI_VENDOR_ID_NETMOS:	return "Netmos";
 	      default:				return "Unknown vendor";
 	}
 }

Re: Netmos PCI parallel card

[Tim Waugh]

[-- Attachment #1: Type: text/plain, Size: 301 bytes --]

On Thu, Feb 15, 2001 at 11:52:46AM +0100, Igmar Palsenberg wrote:

> Attached is a patch to make a Netmos PCI parallal port card working.

Please try the following patch instead.  That card _should_ have a
working ECR.

<URL:ftp://people.redhat.com/twaugh/patches/linux24/linux-netmos.patch>

Tim.
*/

[-- Attachment #2: Type: application/pgp-signature, Size: 232 bytes --]