* Re: interrupt problem with MPS 1.4 / not with MPS 1.1 ?
2001-05-31 18:39 interrupt problem with MPS 1.4 / not with MPS 1.1 ? thunder7
@ 2001-05-31 18:06 ` Greg KH
2001-05-31 19:48 ` [lkml]Re: " thunder7
0 siblings, 1 reply; 11+ messages in thread
From: Greg KH @ 2001-05-31 18:06 UTC (permalink / raw)
To: thunder7; +Cc: linux-kernel
On Thu, May 31, 2001 at 08:39:08PM +0200, thunder7@xs4all.nl wrote:
> What information would be necessary to debug this?
Which kernel version?
greg k-h
^ permalink raw reply [flat|nested] 11+ messages in thread
* interrupt problem with MPS 1.4 / not with MPS 1.1 ?
@ 2001-05-31 18:39 thunder7
2001-05-31 18:06 ` Greg KH
0 siblings, 1 reply; 11+ messages in thread
From: thunder7 @ 2001-05-31 18:39 UTC (permalink / raw)
To: linux-kernel
Hardware:
Abit VP6 (Via 694x) x86/SMP motherboard
with USB controller
If I set the bios for MPS 1.1, USB runs fine. If I set the bios
for MPS 1.4, I get this:
May 31 13:08:06 middle kernel: hub.c: USB new device connect on bus1/1, assigned device number 4
May 31 13:08:09 middle kernel: usb_control/bulk_msg: timeout
May 31 13:08:09 middle kernel: usb.c: USB device not accepting new address=4 (error=-110)
May 31 13:08:09 middle kernel: hub.c: USB new device connect on bus1/1, assigned device number 5
May 31 13:08:12 middle kernel: usb_control/bulk_msg: timeout
May 31 13:08:12 middle kernel: usb.c: USB device not accepting new address=5 (error=-110)
May 31 13:08:12 middle kernel: hub.c: USB new device connect on bus1/1, assigned device number 6
May 31 13:08:15 middle kernel: usb_control/bulk_msg: timeout
May 31 13:08:15 middle kernel: usb.c: USB device not accepting new address=6 (error=-110)
May 31 13:08:16 middle kernel: hub.c: USB new device connect on bus1/1, assigned device number 7
May 31 13:08:19 middle kernel: usb_control/bulk_msg: timeout
May 31 13:08:19 middle kernel: usb.c: USB device not accepting new address=7 (error=-110)
May 31 13:08:19 middle kernel: hub.c: USB new device connect on bus1/1, assigned device number 8
May 31 13:08:22 middle kernel: usb_control/bulk_msg: timeout
May 31 13:08:22 middle kernel: usb.c: USB device not accepting new address=8 (error=-110)
May 31 13:08:22 middle kernel: hub.c: USB new device connect on bus1/1, assigned device number 9
Now I understand this mail doesn't have all the necessary info, but my
question is:
What information would be necessary to debug this?
dmesg
/var/log/messages
lspci -vv (or -x?)
or more?
Jurriaan
--
BOFH excuse #57:
Groundskeepers stole the root password
GNU/Linux 2.4.5-ac4 SMP/ReiserFS 2x1402 bogomips load av: 0.41 0.11 0.03
^ permalink raw reply [flat|nested] 11+ messages in thread
* Re: interrupt problem with MPS 1.4 / not with MPS 1.1 ?
2001-05-31 19:48 ` [lkml]Re: " thunder7
@ 2001-05-31 18:56 ` Greg KH
2001-06-01 8:51 ` thunder7
0 siblings, 1 reply; 11+ messages in thread
From: Greg KH @ 2001-05-31 18:56 UTC (permalink / raw)
To: thunder7; +Cc: linux-kernel
On Thu, May 31, 2001 at 09:48:35PM +0200, thunder7@xs4all.nl wrote:
> On Thu, May 31, 2001 at 11:06:42AM -0700, Greg KH wrote:
> > On Thu, May 31, 2001 at 08:39:08PM +0200, thunder7@xs4all.nl wrote:
> > > What information would be necessary to debug this?
> >
> > Which kernel version?
> >
> > greg k-h
> >
> 2.4.5-ac4, but I rebooted in 2.4.4 and it did the same.
Is the BIOS set to "Plug and Play supported OS" somewhere? If not, try
enabling it.
Also the MPS 1.4 boot messages would be helpful :)
thanks,
greg k-h
^ permalink raw reply [flat|nested] 11+ messages in thread
* Re: [lkml]Re: interrupt problem with MPS 1.4 / not with MPS 1.1 ?
2001-05-31 18:06 ` Greg KH
@ 2001-05-31 19:48 ` thunder7
2001-05-31 18:56 ` Greg KH
0 siblings, 1 reply; 11+ messages in thread
From: thunder7 @ 2001-05-31 19:48 UTC (permalink / raw)
To: Greg KH; +Cc: linux-kernel
On Thu, May 31, 2001 at 11:06:42AM -0700, Greg KH wrote:
> On Thu, May 31, 2001 at 08:39:08PM +0200, thunder7@xs4all.nl wrote:
> > What information would be necessary to debug this?
>
> Which kernel version?
>
> greg k-h
>
2.4.5-ac4, but I rebooted in 2.4.4 and it did the same.
I'll try and add some info here (from the bios= MPS 1.1 case!)
I have the following expansion cards:
Matrox G400 agp video-card
ITI 4280 dual-UW scsi + fast ethernet card
NCR860 ultra-scsi card
Soundblaster Live! 5.1 card
from dmesg:
Total of 2 processors activated (2808.21 BogoMIPS).
ENABLING IO-APIC IRQs
...changing IO-APIC physical APIC ID to 2 ... ok.
init IO_APIC IRQs
IO-APIC (apicid-pin) 2-0, 2-16, 2-17, 2-18, 2-19, 2-20, 2-21, 2-22, 2-23 not connected.
..TIMER: vector=49 pin1=2 pin2=0
number of MP IRQ sources: 16.
number of IO-APIC #2 registers: 24.
testing the IO APIC.......................
IO APIC #2......
.... register #00: 02000000
....... : physical APIC id: 02
.... register #01: 00178011
....... : max redirection entries: 0017
....... : IO APIC version: 0011
WARNING: unexpected IO-APIC, please mail
to linux-smp@vger.kernel.org
.... register #02: 00000000
....... : arbitration: 00
.... IRQ redirection table:
NR Log Phy Mask Trig IRR Pol Stat Dest Deli Vect:
00 000 00 1 0 0 0 0 0 0 00
01 003 03 0 0 0 0 0 1 1 39
02 003 03 0 0 0 0 0 1 1 31
03 003 03 0 0 0 0 0 1 1 41
04 003 03 0 0 0 0 0 1 1 49
05 003 03 1 1 0 1 0 1 1 51
06 003 03 0 0 0 0 0 1 1 59
07 003 03 0 0 0 0 0 1 1 61
08 003 03 0 0 0 0 0 1 1 69
09 003 03 0 0 0 0 0 1 1 71
0a 003 03 1 1 0 1 0 1 1 79
0b 003 03 1 1 0 1 0 1 1 81
0c 003 03 0 0 0 0 0 1 1 89
0d 003 03 0 0 0 0 0 1 1 91
0e 003 03 0 0 0 0 0 1 1 99
0f 003 03 1 1 0 1 0 1 1 A1
10 000 00 1 0 0 0 0 0 0 00
11 000 00 1 0 0 0 0 0 0 00
12 000 00 1 0 0 0 0 0 0 00
13 000 00 1 0 0 0 0 0 0 00
14 000 00 1 0 0 0 0 0 0 00
15 000 00 1 0 0 0 0 0 0 00
16 000 00 1 0 0 0 0 0 0 00
17 000 00 1 0 0 0 0 0 0 00
IRQ to pin mappings:
IRQ0 -> 0:2
IRQ1 -> 0:1
IRQ3 -> 0:3
IRQ4 -> 0:4
IRQ5 -> 0:5
IRQ6 -> 0:6
IRQ7 -> 0:7
IRQ8 -> 0:8
IRQ9 -> 0:9
IRQ10 -> 0:10
IRQ11 -> 0:11
IRQ12 -> 0:12
IRQ13 -> 0:13
IRQ14 -> 0:14
IRQ15 -> 0:15
.................................... done.
Using local APIC timer interrupts.
calibrating APIC timer ...
..... CPU clock speed is 703.1338 MHz.
..... host bus clock speed is 100.4475 MHz.
cpu: 0, clocks: 1004475, slice: 334825
CPU0<T0:1004464,T1:669632,D:7,S:334825,C:1004475>
cpu: 1, clocks: 1004475, slice: 334825
CPU1<T0:1004464,T1:334800,D:14,S:334825,C:1004475>
checking TSC synchronization across CPUs: passed.
mtrr: your CPUs had inconsistent variable MTRR settings
mtrr: probably your BIOS does not setup all CPUs
PCI: PCI BIOS revision 2.10 entry at 0xfb3a0, last bus=2
PCI: Using configuration type 1
PCI: Probing PCI hardware
Unknown bridge resource 0: assuming transparent
Unknown bridge resource 2: assuming transparent
PCI: Using IRQ router VIA [1106/0686] at 00:07.0
Linux NET4.0 for Linux 2.4
usb.c: registered new driver hub
uhci.c: USB UHCI at I/O 0xa000, IRQ 5
usb.c: new USB bus registered, assigned bus number 1
hub.c: USB hub found
hub.c: 2 ports detected
uhci.c: USB UHCI at I/O 0xa400, IRQ 5
usb.c: new USB bus registered, assigned bus number 2
hub.c: USB hub found
hub.c: 2 ports detected
uhci.c: Linus Torvalds, Johannes Erdfelt, Randy Dunlap, Georg Acher, Deti Fliegl, Thomas Sailer, Roman Weissgaerber
uhci.c: USB Universal Host Controller Interface driver
Initializing USB Mass Storage driver...
usb.c: registered new driver usb-storage
USB Mass Storage support registered.
NET4: Linux TCP/IP 1.0 for NET4.0
Freeing unused kernel memory: 248k freed
hub.c: USB new device connect on bus1/1, assigned device number 2
scsi3 : SCSI emulation for USB Mass Storage devices
Vendor: IOMEGA Model: ZIP 250 Rev: 61.T
Type: Direct-Access ANSI SCSI revision: 02
Attached scsi removable disk sda at scsi3, channel 0, id 0, lun 0
sda : READ CAPACITY failed.
sda : status = 1, message = 00, host = 0, driver = 08
sda : extended sense code = 2
sda : block size assumed to be 512 bytes, disk size 1GB.
sda: I/O error: dev 08:00, sector 0
unable to read partition table
WARNING: USB Mass Storage data integrity not assured
USB Mass Storage device found at 2
Adding Swap: 1047776k swap-space (priority -1)
from lspci:
00:00.0 Host bridge: VIA Technologies, Inc. VT82C693A/694x [Apollo PRO133x] (rev c4)
Subsystem: ABIT Computer Corp.: Unknown device a204
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR-
Latency: 8
Region 0: Memory at d0000000 (32-bit, prefetchable) [size=64M]
Capabilities: [a0] AGP version 2.0
Status: RQ=31 SBA+ 64bit- FW- Rate=x1,x2
Command: RQ=0 SBA- AGP- 64bit- FW- Rate=<none>
Capabilities: [c0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:01.0 PCI bridge: VIA Technologies, Inc. VT82C598/694x [Apollo MVP3/Pro133x AGP] (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR-
Latency: 0
Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
Memory behind bridge: d6000000-d8ffffff
Prefetchable memory behind bridge: d4000000-d5ffffff
BridgeCtl: Parity- SERR- NoISA+ VGA+ MAbort- >Reset- FastB2B-
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1+ D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:07.0 ISA bridge: VIA Technologies, Inc. VT82C686 [Apollo Super South] (rev 40)
Subsystem: ABIT Computer Corp.: Unknown device 0000
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping+ SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Capabilities: [c0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:07.1 IDE interface: VIA Technologies, Inc. Bus Master IDE (rev 06) (prog-if 8a [Master SecP PriP])
Subsystem: VIA Technologies, Inc. Bus Master IDE
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32
Region 4: I/O ports at a800 [size=16]
Capabilities: [c0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:07.2 USB Controller: VIA Technologies, Inc. UHCI USB (rev 16) (prog-if 00 [UHCI])
Subsystem: Unknown device 0925:1234
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32, cache line size 08
Interrupt: pin D routed to IRQ 5
Region 4: I/O ports at a000 [size=32]
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:07.3 USB Controller: VIA Technologies, Inc. UHCI USB (rev 16) (prog-if 00 [UHCI])
Subsystem: Unknown device 0925:1234
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32, cache line size 08
Interrupt: pin D routed to IRQ 5
Region 4: I/O ports at a400 [size=32]
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:07.4 Bridge: VIA Technologies, Inc. VT82C686 [Apollo Super ACPI] (rev 40)
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin ? routed to IRQ 3
Capabilities: [68] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:09.0 PCI bridge: Digital Equipment Corporation DECchip 21152 (rev 02) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32, cache line size 08
Bus: primary=00, secondary=02, subordinate=02, sec-latency=32
I/O behind bridge: 00009000-00009fff
Memory behind bridge: d9000000-daffffff
BridgeCtl: Parity- SERR+ NoISA+ VGA- MAbort- >Reset- FastB2B-
00:0a.0 SCSI storage controller: Symbios Logic Inc. (formerly NCR) 53c860 (rev 13)
Subsystem: Symbios Logic Inc. (formerly NCR): Unknown device 1000
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32 (2000ns min, 16000ns max), cache line size 08
Interrupt: pin A routed to IRQ 11
Region 0: I/O ports at ac00 [size=256]
Region 1: Memory at dc000000 (32-bit, non-prefetchable) [size=256]
Capabilities: [40] Power Management version 1
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:0b.0 Multimedia audio controller: Creative Labs SB Live! EMU10000 (rev 07)
Subsystem: Creative Labs: Unknown device 8061
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32 (500ns min, 5000ns max)
Interrupt: pin A routed to IRQ 11
Region 0: I/O ports at b000 [size=32]
Capabilities: [dc] Power Management version 1
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:0b.1 Input device controller: Creative Labs SB Live! (rev 07)
Subsystem: Creative Labs Gameport Joystick
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32
Region 0: I/O ports at b400 [size=8]
Capabilities: [dc] Power Management version 1
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:0e.0 Unknown mass storage controller: Triones Technologies, Inc. HPT366 (rev 03)
Subsystem: Triones Technologies, Inc.: Unknown device 0001
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 120 (2000ns min, 2000ns max), cache line size 08
Interrupt: pin A routed to IRQ 10
Region 0: I/O ports at b800 [size=8]
Region 1: I/O ports at bc00 [size=4]
Region 2: I/O ports at c000 [size=8]
Region 3: I/O ports at c400 [size=4]
Region 4: I/O ports at c800 [size=256]
Expansion ROM at <unassigned> [disabled] [size=128K]
Capabilities: [60] Power Management version 2
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
01:00.0 VGA compatible controller: Matrox Graphics, Inc. MGA G400 AGP (rev 03) (prog-if 00 [VGA])
Subsystem: Matrox Graphics, Inc. Millennium G400 32Mb SGRAM
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32 (4000ns min, 8000ns max), cache line size 08
Interrupt: pin A routed to IRQ 15
Region 0: Memory at d4000000 (32-bit, prefetchable) [size=32M]
Region 1: Memory at d6000000 (32-bit, non-prefetchable) [size=16K]
Region 2: Memory at d7000000 (32-bit, non-prefetchable) [size=8M]
Expansion ROM at <unassigned> [disabled] [size=64K]
Capabilities: [dc] Power Management version 2
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [f0] AGP version 2.0
Status: RQ=31 SBA+ 64bit- FW- Rate=x1,x2
Command: RQ=31 SBA+ AGP+ 64bit- FW- Rate=x1
02:00.0 SCSI storage controller: Symbios Logic Inc. (formerly NCR) 53c875 (rev 04)
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 72 (4250ns min, 16000ns max), cache line size 08
Interrupt: pin A routed to IRQ 15
Region 0: I/O ports at 9000 [size=256]
Region 1: Memory at da001000 (32-bit, non-prefetchable) [size=256]
Region 2: Memory at da000000 (32-bit, non-prefetchable) [size=4K]
Expansion ROM at <unassigned> [disabled] [size=64K]
02:01.0 SCSI storage controller: Symbios Logic Inc. (formerly NCR) 53c875 (rev 04)
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 72 (4250ns min, 16000ns max), cache line size 08
Interrupt: pin A routed to IRQ 11
Region 0: I/O ports at 9400 [size=256]
Region 1: Memory at da002000 (32-bit, non-prefetchable) [size=256]
Region 2: Memory at da003000 (32-bit, non-prefetchable) [size=4K]
Expansion ROM at <unassigned> [disabled] [size=64K]
02:02.0 Ethernet controller: Digital Equipment Corporation DECchip 21140 [FasterNet] (rev 22)
Subsystem: Digital Equipment Corporation: Unknown device 500a
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 96 (5000ns min, 10000ns max), cache line size 08
Interrupt: pin A routed to IRQ 10
Region 0: I/O ports at 9800 [size=128]
Region 1: Memory at da004000 (32-bit, non-prefetchable) [size=128]
Expansion ROM at <unassigned> [disabled] [size=256K]
I know that with MPS 1.4, the USB controller finds itself at an
unshared interrupt 19. I can't reboot at the moment to check.
Good luck,
Jurriaan
--
HORROR FILM WISDOM:
13. If you are using a gun to combat the all-consuming evil, it is a good
idea to quickly find a new means of defense, because no matter how much
ammo you have, you'll run out just before you kill the monster (unless
your name is Ash, in which case, you'll never have to reload).
GNU/Linux 2.4.5-ac4 SMP/ReiserFS 2x1402 bogomips load av: 0.06 0.03 0.00
^ permalink raw reply [flat|nested] 11+ messages in thread
* Re: interrupt problem with MPS 1.4 / not with MPS 1.1 ?
2001-05-31 20:45 ` Manfred Spraul
@ 2001-06-01 5:14 ` thunder7
2001-06-01 5:20 ` Jeff Garzik
2001-06-01 17:28 ` Manfred Spraul
0 siblings, 2 replies; 11+ messages in thread
From: thunder7 @ 2001-06-01 5:14 UTC (permalink / raw)
To: Manfred Spraul; +Cc: linux-kernel
On Thu, May 31, 2001 at 10:45:17PM +0200, Manfred Spraul wrote:
> thunder7@xs4all.nl wrote:
> >
> > 00:07.2 USB Controller: VIA Technologies, Inc. UHCI USB (rev 16) (prog-if 00 [UHCI])
> > Subsystem: Unknown device 0925:1234
> > Flags: bus master, medium devsel, latency 32, IRQ 5
> > I/O ports at a000 [size=32]
> > Capabilities: [80] Power Management version 2
> > 30: 00 00 00 00 80 00 00 00 00 00 00 00 05 04 00 00
> >
> > 0x3X is at 5, not at 3.
> >
> You still run with MPS 1.1.
> It should be 3 or 19 after you reboot with MPS 1.4.
>
> Could you please try the following commands as root, but just before
> rebooting. It'll kill the USB controller.
>
> #setpci -s 00:07.2 INTERRUPT_LINE=15
> #lspci -vx -s 00:07.2
> <<< 0x3C should be 15
> #setpci -s 00:07.2 INTERRUPT_LINE=19
> #lspci -vx -s 00:07.2
> <<< 0x3C is now either 19 or 3
>
:setpci -s 00:07.2 INTERRUPT_LINE=15
:lspci -vx -s 00:07.2
00:07.2 USB Controller: VIA Technologies, Inc. UHCI USB (rev 16) (prog-if 00 [UHCI])
Subsystem: Unknown device 0925:1234
Flags: bus master, medium devsel, latency 32, IRQ 19
I/O ports at a000 [size=32]
Capabilities: [80] Power Management version 2
30: 00 00 00 00 80 00 00 00 00 00 00 00 15 04 00 00
:setpci -s 00:07.2 INTERRUPT_LINE=19
:lspci -vx -s 00:07.2
00:07.2 USB Controller: VIA Technologies, Inc. UHCI USB (rev 16) (prog-if 00 [UHCI])
Subsystem: Unknown device 0925:1234
Flags: bus master, medium devsel, latency 32, IRQ 19
I/O ports at a000 [size=32]
Capabilities: [80] Power Management version 2
30: 00 00 00 00 80 00 00 00 00 00 00 00 19 04 00 00
So that is correct. I'll attach all the information from the MPS 1.4
reboot, in which 00:07.2 happily points at 05, while everything else
thinks it's at 19.....
0: 00000000000f0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000001fff0000 (usable)
BIOS-e820: 000000001fff0000 - 000000001fff3000 (ACPI NVS)
BIOS-e820: 000000001fff3000 - 0000000020000000 (ACPI data)
BIOS-e820: 00000000fec00000 - 00000000fec01000 (reserved)
BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
BIOS-e820: 00000000ffff0000 - 0000000100000000 (reserved)
found SMP MP-table at 000f5770
hm, page 000f5000 reserved twice.
hm, page 000f6000 reserved twice.
hm, page 000f1000 reserved twice.
hm, page 000f2000 reserved twice.
On node 0 totalpages: 131056
zone(0): 4096 pages.
zone(1): 126960 pages.
zone(2): 0 pages.
Intel MultiProcessor Specification v1.4
Virtual Wire compatibility mode.
OEM ID: OEM00000 Product ID: PROD00000000 APIC at: 0xFEE00000
Processor #0 Pentium(tm) Pro APIC version 17
Processor #1 Pentium(tm) Pro APIC version 17
I/O APIC #2 Version 17 at 0xFEC00000.
Processors: 2
Kernel command line: auto BOOT_IMAGE=SuSE-2.4.5ac5 ro root=2101 BOOT_FILE=/boot/prod/vmlinuz-245ac5 video=matrox:vesa:0x11E,fv:80,sgram
Total of 2 processors activated (2808.21 BogoMIPS).
ENABLING IO-APIC IRQs
...changing IO-APIC physical APIC ID to 2 ... ok.
init IO_APIC IRQs
IO-APIC (apicid-pin) 2-0, 2-5, 2-10, 2-11, 2-15, 2-20, 2-21, 2-22, 2-23 not connected.
..TIMER: vector=49 pin1=2 pin2=0
number of MP IRQ sources: 22.
number of IO-APIC #2 registers: 24.
testing the IO APIC.......................
IO APIC #2......
.... register #00: 02000000
....... : physical APIC id: 02
.... register #01: 00178011
....... : max redirection entries: 0017
....... : IO APIC version: 0011
WARNING: unexpected IO-APIC, please mail
to linux-smp@vger.kernel.org
.... register #02: 00000000
....... : arbitration: 00
.... IRQ redirection table:
NR Log Phy Mask Trig IRR Pol Stat Dest Deli Vect:
00 000 00 1 0 0 0 0 0 0 00
01 003 03 0 0 0 0 0 1 1 39
02 003 03 0 0 0 0 0 1 1 31
03 003 03 0 0 0 0 0 1 1 41
04 003 03 0 0 0 0 0 1 1 49
05 000 00 1 0 0 0 0 0 0 00
06 003 03 0 0 0 0 0 1 1 51
07 003 03 0 0 0 0 0 1 1 59
08 003 03 0 0 0 0 0 1 1 61
09 003 03 0 0 0 0 0 1 1 69
0a 000 00 1 0 0 0 0 0 0 00
0b 000 00 1 0 0 0 0 0 0 00
0c 003 03 0 0 0 0 0 1 1 71
0d 003 03 0 0 0 0 0 1 1 79
0e 003 03 0 0 0 0 0 1 1 81
0f 000 00 1 0 0 0 0 0 0 00
10 003 03 1 1 0 1 0 1 1 89
11 003 03 1 1 0 1 0 1 1 91
12 003 03 1 1 0 1 0 1 1 99
13 003 03 1 1 0 1 0 1 1 A1
14 000 00 1 0 0 0 0 0 0 00
15 000 00 1 0 0 0 0 0 0 00
16 000 00 1 0 0 0 0 0 0 00
17 000 00 1 0 0 0 0 0 0 00
IRQ to pin mappings:
IRQ0 -> 0:2
IRQ1 -> 0:1
IRQ3 -> 0:3
IRQ4 -> 0:4
IRQ6 -> 0:6
IRQ7 -> 0:7
IRQ8 -> 0:8
IRQ9 -> 0:9
IRQ12 -> 0:12
IRQ13 -> 0:13
IRQ14 -> 0:14
IRQ16 -> 0:16
IRQ17 -> 0:17
IRQ18 -> 0:18
IRQ19 -> 0:19
.................................... done.
Using local APIC timer interrupts.
calibrating APIC timer ...
..... CPU clock speed is 703.2166 MHz.
..... host bus clock speed is 100.4593 MHz.
PCI: Probing PCI hardware
Unknown bridge resource 0: assuming transparent
Unknown bridge resource 2: assuming transparent
PCI: Using IRQ router VIA [1106/0686] at 00:07.0
PCI->APIC IRQ transform: (B0,I7,P3) -> 19
PCI->APIC IRQ transform: (B0,I7,P3) -> 19
PCI->APIC IRQ transform: (B0,I10,P0) -> 17
PCI->APIC IRQ transform: (B0,I11,P0) -> 17
PCI->APIC IRQ transform: (B0,I14,P0) -> 18
PCI->APIC IRQ transform: (B1,I0,P0) -> 16
PCI->APIC IRQ transform: (B2,I0,P0) -> 16
PCI->APIC IRQ transform: (B2,I1,P0) -> 17
PCI->APIC IRQ transform: (B2,I2,P0) -> 18
Linux NET4.0 for Linux 2.4
i2c-core.o: adapter MAVEN:fb0 on i2c-matroxfb registered as adapter 2.
usb.c: registered new driver hub
uhci.c: USB UHCI at I/O 0xa000, IRQ 19
usb.c: new USB bus registered, assigned bus number 1
hub.c: USB hub found
hub.c: 2 ports detected
uhci.c: USB UHCI at I/O 0xa400, IRQ 19
usb.c: new USB bus registered, assigned bus number 2
hub.c: USB hub found
hub.c: 2 ports detected
uhci.c: Linus Torvalds, Johannes Erdfelt, Randy Dunlap, Georg Acher, Deti Fliegl, Thomas Sailer, Roman Weissgaerber
uhci.c: USB Universal Host Controller Interface driver
Initializing USB Mass Storage driver...
usb.c: registered new driver usb-storage
USB Mass Storage support registered.
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP, IGMP
IP: routing cache hash table of 2048 buckets, 32Kbytes
TCP: Hash tables configured (established 16384 bind 21845)
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
VFS: Mounted root (ext2 filesystem) readonly.
Freeing unused kernel memory: 248k freed
hub.c: USB new device connect on bus1/1, assigned device number 2
Adding Swap: 1047776k swap-space (priority -1)
reiserfs: checking transaction log (device 22:02) ...
usb_control/bulk_msg: timeout
usb.c: USB device not accepting new address=2 (error=-110)
hub.c: USB new device connect on bus1/1, assigned device number 3
usb_control/bulk_msg: timeout
usb.c: USB device not accepting new address=3 (error=-110)
/proc/interrupts:
CPU0 CPU1
0: 6043 3005 IO-APIC-edge timer
1: 38 3 IO-APIC-edge keyboard
2: 0 0 XT-PIC cascade
8: 0 2 IO-APIC-edge rtc
14: 179 224 IO-APIC-edge ide0
16: 32 33 IO-APIC-level sym53c8xx
17: 22 22 IO-APIC-level sym53c8xx, sym53c8xx, EMU10K1
18: 1657 1681 IO-APIC-level ide2, ide3, DE500-AA (eth0)
19: 0 0 IO-APIC-level usb-uhci, usb-uhci
NMI: 0 0
LOC: 8966 8963
ERR: 0
MIS: 0
lspci:
00:00.0 Host bridge: VIA Technologies, Inc. VT82C693A/694x [Apollo PRO133x] (rev c4)
Subsystem: ABIT Computer Corp.: Unknown device a204
Flags: bus master, medium devsel, latency 8
Memory at d0000000 (32-bit, prefetchable) [size=64M]
Capabilities: [a0] AGP version 2.0
Capabilities: [c0] Power Management version 2
00:01.0 PCI bridge: VIA Technologies, Inc. VT82C598/694x [Apollo MVP3/Pro133x AGP] (prog-if 00 [Normal decode])
Flags: bus master, 66Mhz, medium devsel, latency 0
Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
Memory behind bridge: d6000000-d8ffffff
Prefetchable memory behind bridge: d4000000-d5ffffff
Capabilities: [80] Power Management version 2
00:07.0 ISA bridge: VIA Technologies, Inc. VT82C686 [Apollo Super South] (rev 40)
Subsystem: ABIT Computer Corp.: Unknown device 0000
Flags: bus master, stepping, medium devsel, latency 0
Capabilities: [c0] Power Management version 2
00:07.1 IDE interface: VIA Technologies, Inc. Bus Master IDE (rev 06) (prog-if 8a [Master SecP PriP])
Subsystem: VIA Technologies, Inc. Bus Master IDE
Flags: bus master, medium devsel, latency 32
I/O ports at a800 [size=16]
Capabilities: [c0] Power Management version 2
00:07.2 USB Controller: VIA Technologies, Inc. UHCI USB (rev 16) (prog-if 00 [UHCI])
Subsystem: Unknown device 0925:1234
Flags: bus master, medium devsel, latency 32, IRQ 19
I/O ports at a000 [size=32]
Capabilities: [80] Power Management version 2
00:07.3 USB Controller: VIA Technologies, Inc. UHCI USB (rev 16) (prog-if 00 [UHCI])
Subsystem: Unknown device 0925:1234
Flags: bus master, medium devsel, latency 32, IRQ 19
I/O ports at a400 [size=32]
Capabilities: [80] Power Management version 2
00:07.4 Bridge: VIA Technologies, Inc. VT82C686 [Apollo Super ACPI] (rev 40)
Flags: medium devsel, IRQ 3
Capabilities: [68] Power Management version 2
00:09.0 PCI bridge: Digital Equipment Corporation DECchip 21152 (rev 02) (prog-if 00 [Normal decode])
Flags: bus master, medium devsel, latency 32
Bus: primary=00, secondary=02, subordinate=02, sec-latency=32
I/O behind bridge: 00009000-00009fff
Memory behind bridge: d9000000-daffffff
00:0a.0 SCSI storage controller: Symbios Logic Inc. (formerly NCR) 53c860 (rev 13)
Subsystem: Symbios Logic Inc. (formerly NCR): Unknown device 1000
Flags: bus master, medium devsel, latency 32, IRQ 17
I/O ports at ac00 [size=256]
Memory at dc000000 (32-bit, non-prefetchable) [size=256]
Capabilities: [40] Power Management version 1
00:0b.0 Multimedia audio controller: Creative Labs SB Live! EMU10000 (rev 07)
Subsystem: Creative Labs: Unknown device 8061
Flags: bus master, medium devsel, latency 32, IRQ 17
I/O ports at b000 [size=32]
Capabilities: [dc] Power Management version 1
00:0b.1 Input device controller: Creative Labs SB Live! (rev 07)
Subsystem: Creative Labs Gameport Joystick
Flags: bus master, medium devsel, latency 32
I/O ports at b400 [size=8]
Capabilities: [dc] Power Management version 1
00:0e.0 Unknown mass storage controller: Triones Technologies, Inc. HPT366 (rev 03)
Subsystem: Triones Technologies, Inc.: Unknown device 0001
Flags: bus master, 66Mhz, medium devsel, latency 120, IRQ 18
I/O ports at b800 [size=8]
I/O ports at bc00 [size=4]
I/O ports at c000 [size=8]
I/O ports at c400 [size=4]
I/O ports at c800 [size=256]
Expansion ROM at <unassigned> [disabled] [size=128K]
Capabilities: [60] Power Management version 2
01:00.0 VGA compatible controller: Matrox Graphics, Inc. MGA G400 AGP (rev 03) (prog-if 00 [VGA])
Subsystem: Matrox Graphics, Inc. Millennium G400 32Mb SGRAM
Flags: bus master, medium devsel, latency 32, IRQ 16
Memory at d4000000 (32-bit, prefetchable) [size=32M]
Memory at d6000000 (32-bit, non-prefetchable) [size=16K]
Memory at d7000000 (32-bit, non-prefetchable) [size=8M]
Expansion ROM at <unassigned> [disabled] [size=64K]
Capabilities: [dc] Power Management version 2
Capabilities: [f0] AGP version 2.0
02:00.0 SCSI storage controller: Symbios Logic Inc. (formerly NCR) 53c875 (rev 04)
Flags: bus master, medium devsel, latency 72, IRQ 16
I/O ports at 9000 [size=256]
Memory at da001000 (32-bit, non-prefetchable) [size=256]
Memory at da000000 (32-bit, non-prefetchable) [size=4K]
Expansion ROM at <unassigned> [disabled] [size=64K]
02:01.0 SCSI storage controller: Symbios Logic Inc. (formerly NCR) 53c875 (rev 04)
Flags: bus master, medium devsel, latency 72, IRQ 17
I/O ports at 9400 [size=256]
Memory at da002000 (32-bit, non-prefetchable) [size=256]
Memory at da003000 (32-bit, non-prefetchable) [size=4K]
Expansion ROM at <unassigned> [disabled] [size=64K]
02:02.0 Ethernet controller: Digital Equipment Corporation DECchip 21140 [FasterNet] (rev 22)
Subsystem: Digital Equipment Corporation: Unknown device 500a
Flags: bus master, medium devsel, latency 96, IRQ 18
I/O ports at 9800 [size=128]
Memory at da004000 (32-bit, non-prefetchable) [size=128]
Expansion ROM at <unassigned> [disabled] [size=256K]
lspci -vvvxx:
00:00.0 Host bridge: VIA Technologies, Inc. VT82C693A/694x [Apollo PRO133x] (rev c4)
Subsystem: ABIT Computer Corp.: Unknown device a204
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR-
Latency: 8
Region 0: Memory at d0000000 (32-bit, prefetchable) [size=64M]
Capabilities: [a0] AGP version 2.0
Status: RQ=31 SBA+ 64bit- FW- Rate=x1,x2
Command: RQ=0 SBA- AGP- 64bit- FW- Rate=<none>
Capabilities: [c0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00: 06 11 91 06 06 00 10 22 c4 00 00 06 00 08 00 00
10: 08 00 00 d0 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 7b 14 04 a2
30: 00 00 00 00 a0 00 00 00 00 00 00 00 00 00 00 00
00:01.0 PCI bridge: VIA Technologies, Inc. VT82C598/694x [Apollo MVP3/Pro133x AGP] (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR-
Latency: 0
Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
I/O behind bridge: 0000f000-00000fff
Memory behind bridge: d6000000-d8ffffff
Prefetchable memory behind bridge: d4000000-d5ffffff
BridgeCtl: Parity- SERR- NoISA+ VGA+ MAbort- >Reset- FastB2B-
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1+ D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00: 06 11 98 85 07 00 30 22 00 00 04 06 00 00 01 00
10: 00 00 00 00 00 00 00 00 00 01 01 00 f0 00 00 00
20: 00 d6 f0 d8 00 d4 f0 d5 00 00 00 00 00 00 00 00
30: 00 00 00 00 80 00 00 00 00 00 00 00 00 00 0c 00
00:07.0 ISA bridge: VIA Technologies, Inc. VT82C686 [Apollo Super South] (rev 40)
Subsystem: ABIT Computer Corp.: Unknown device 0000
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping+ SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Capabilities: [c0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00: 06 11 86 06 87 00 10 02 40 00 01 06 00 00 80 00
10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 7b 14 00 00
30: 00 00 00 00 c0 00 00 00 00 00 00 00 00 00 00 00
00:07.1 IDE interface: VIA Technologies, Inc. Bus Master IDE (rev 06) (prog-if 8a [Master SecP PriP])
Subsystem: VIA Technologies, Inc. Bus Master IDE
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32
Region 4: I/O ports at a800 [size=16]
Capabilities: [c0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00: 06 11 71 05 07 00 90 02 06 8a 01 01 00 20 00 00
10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
20: 01 a8 00 00 00 00 00 00 00 00 00 00 06 11 71 05
30: 00 00 00 00 c0 00 00 00 00 00 00 00 ff 00 00 00
00:07.2 USB Controller: VIA Technologies, Inc. UHCI USB (rev 16) (prog-if 00 [UHCI])
Subsystem: Unknown device 0925:1234
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32, cache line size 08
Interrupt: pin D routed to IRQ 19
Region 4: I/O ports at a000 [size=32]
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00: 06 11 38 30 07 00 10 02 16 00 03 0c 08 20 00 00
10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
20: 01 a0 00 00 00 00 00 00 00 00 00 00 25 09 34 12
30: 00 00 00 00 80 00 00 00 00 00 00 00 05 04 00 00
00:07.3 USB Controller: VIA Technologies, Inc. UHCI USB (rev 16) (prog-if 00 [UHCI])
Subsystem: Unknown device 0925:1234
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32, cache line size 08
Interrupt: pin D routed to IRQ 19
Region 4: I/O ports at a400 [size=32]
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00: 06 11 38 30 07 00 10 02 16 00 03 0c 08 20 00 00
10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
20: 01 a4 00 00 00 00 00 00 00 00 00 00 25 09 34 12
30: 00 00 00 00 80 00 00 00 00 00 00 00 05 04 00 00
00:07.4 Bridge: VIA Technologies, Inc. VT82C686 [Apollo Super ACPI] (rev 40)
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin ? routed to IRQ 3
Capabilities: [68] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00: 06 11 57 30 00 00 90 02 40 00 80 06 00 00 00 00
10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
30: 00 00 00 00 68 00 00 00 00 00 00 00 00 00 00 00
00:09.0 PCI bridge: Digital Equipment Corporation DECchip 21152 (rev 02) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32, cache line size 08
Bus: primary=00, secondary=02, subordinate=02, sec-latency=32
I/O behind bridge: 00009000-00009fff
Memory behind bridge: d9000000-daffffff
Prefetchable memory behind bridge: 00000000fff00000-0000000000000000
BridgeCtl: Parity- SERR+ NoISA+ VGA- MAbort- >Reset- FastB2B-
00: 11 10 24 00 07 01 80 02 02 00 04 06 08 20 01 00
10: 00 00 00 00 00 00 00 00 00 02 02 20 91 91 80 22
20: 00 d9 f0 da f1 ff 01 00 00 00 00 00 00 00 00 00
30: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 06 00
00:0a.0 SCSI storage controller: Symbios Logic Inc. (formerly NCR) 53c860 (rev 13)
Subsystem: Symbios Logic Inc. (formerly NCR): Unknown device 1000
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32 (2000ns min, 16000ns max), cache line size 08
Interrupt: pin A routed to IRQ 17
Region 0: I/O ports at ac00 [size=256]
Region 1: Memory at dc000000 (32-bit, non-prefetchable) [size=256]
Capabilities: [40] Power Management version 1
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00: 00 10 06 00 47 00 10 02 13 00 00 01 08 20 00 00
10: 01 ac 00 00 00 00 00 dc 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 00 10 00 10
30: 00 00 00 00 40 00 00 00 00 00 00 00 0b 01 08 40
00:0b.0 Multimedia audio controller: Creative Labs SB Live! EMU10000 (rev 07)
Subsystem: Creative Labs: Unknown device 8061
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32 (500ns min, 5000ns max)
Interrupt: pin A routed to IRQ 17
Region 0: I/O ports at b000 [size=32]
Capabilities: [dc] Power Management version 1
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00: 02 11 02 00 05 00 90 02 07 00 01 04 00 20 80 00
10: 01 b0 00 00 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 02 11 61 80
30: 00 00 00 00 dc 00 00 00 00 00 00 00 0b 01 02 14
00:0b.1 Input device controller: Creative Labs SB Live! (rev 07)
Subsystem: Creative Labs Gameport Joystick
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32
Region 0: I/O ports at b400 [size=8]
Capabilities: [dc] Power Management version 1
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00: 02 11 02 70 05 00 90 02 07 00 80 09 00 20 80 00
10: 01 b4 00 00 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 02 11 20 00
30: 00 00 00 00 dc 00 00 00 00 00 00 00 00 00 00 00
00:0e.0 Unknown mass storage controller: Triones Technologies, Inc. HPT366 (rev 03)
Subsystem: Triones Technologies, Inc.: Unknown device 0001
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 120 (2000ns min, 2000ns max), cache line size 08
Interrupt: pin A routed to IRQ 18
Region 0: I/O ports at b800 [size=8]
Region 1: I/O ports at bc00 [size=4]
Region 2: I/O ports at c000 [size=8]
Region 3: I/O ports at c400 [size=4]
Region 4: I/O ports at c800 [size=256]
Expansion ROM at <unassigned> [disabled] [size=128K]
Capabilities: [60] Power Management version 2
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00: 03 11 04 00 05 00 30 02 03 00 80 01 08 78 00 00
10: 01 b8 00 00 01 bc 00 00 01 c0 00 00 01 c4 00 00
20: 01 c8 00 00 00 00 00 00 00 00 00 00 03 11 01 00
30: 00 00 00 00 60 00 00 00 00 00 00 00 0a 01 08 08
01:00.0 VGA compatible controller: Matrox Graphics, Inc. MGA G400 AGP (rev 03) (prog-if 00 [VGA])
Subsystem: Matrox Graphics, Inc. Millennium G400 32Mb SGRAM
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32 (4000ns min, 8000ns max), cache line size 08
Interrupt: pin A routed to IRQ 16
Region 0: Memory at d4000000 (32-bit, prefetchable) [size=32M]
Region 1: Memory at d6000000 (32-bit, non-prefetchable) [size=16K]
Region 2: Memory at d7000000 (32-bit, non-prefetchable) [size=8M]
Expansion ROM at <unassigned> [disabled] [size=64K]
Capabilities: [dc] Power Management version 2
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [f0] AGP version 2.0
Status: RQ=31 SBA+ 64bit- FW- Rate=x1,x2
Command: RQ=31 SBA+ AGP+ 64bit- FW- Rate=x1
00: 2b 10 25 05 07 00 90 02 03 00 00 03 08 20 00 00
10: 08 00 00 d4 00 00 00 d6 00 00 00 d7 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 2b 10 f8 19
30: 00 00 00 00 dc 00 00 00 00 00 00 00 0f 01 10 20
02:00.0 SCSI storage controller: Symbios Logic Inc. (formerly NCR) 53c875 (rev 04)
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 72 (4250ns min, 16000ns max), cache line size 08
Interrupt: pin A routed to IRQ 16
Region 0: I/O ports at 9000 [size=256]
Region 1: Memory at da001000 (32-bit, non-prefetchable) [size=256]
Region 2: Memory at da000000 (32-bit, non-prefetchable) [size=4K]
Expansion ROM at <unassigned> [disabled] [size=64K]
00: 00 10 0f 00 47 00 00 02 04 00 00 01 08 48 00 00
10: 01 90 00 00 00 10 00 da 00 00 00 da 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
30: 00 00 00 00 00 00 00 00 00 00 00 00 0f 01 11 40
02:01.0 SCSI storage controller: Symbios Logic Inc. (formerly NCR) 53c875 (rev 04)
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 72 (4250ns min, 16000ns max), cache line size 08
Interrupt: pin A routed to IRQ 17
Region 0: I/O ports at 9400 [size=256]
Region 1: Memory at da002000 (32-bit, non-prefetchable) [size=256]
Region 2: Memory at da003000 (32-bit, non-prefetchable) [size=4K]
Expansion ROM at <unassigned> [disabled] [size=64K]
00: 00 10 0f 00 47 00 00 02 04 00 00 01 08 48 00 00
10: 01 94 00 00 00 20 00 da 00 30 00 da 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
30: 00 00 00 00 00 00 00 00 00 00 00 00 0b 01 11 40
02:02.0 Ethernet controller: Digital Equipment Corporation DECchip 21140 [FasterNet] (rev 22)
Subsystem: Digital Equipment Corporation: Unknown device 500a
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 96 (5000ns min, 10000ns max), cache line size 08
Interrupt: pin A routed to IRQ 18
Region 0: I/O ports at 9800 [size=128]
Region 1: Memory at da004000 (32-bit, non-prefetchable) [size=128]
Expansion ROM at <unassigned> [disabled] [size=256K]
00: 11 10 09 00 07 00 80 02 22 00 00 02 08 60 00 00
10: 01 98 00 00 00 40 00 da 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 11 10 0a 50
30: 00 00 00 00 00 00 00 00 00 00 00 00 0a 01 14 28
Good luck,
Jurriaan
--
BOFH excuse #222:
I'm not sure. Try calling the Internet's head office -- it's in the book.
GNU/Linux 2.4.5-ac5 SMP/ReiserFS 2x1402 bogomips load av: 0.03 0.10 0.06
^ permalink raw reply [flat|nested] 11+ messages in thread
* Re: interrupt problem with MPS 1.4 / not with MPS 1.1 ?
2001-06-01 5:14 ` thunder7
@ 2001-06-01 5:20 ` Jeff Garzik
2001-06-01 5:39 ` thunder7
2001-06-01 17:28 ` Manfred Spraul
1 sibling, 1 reply; 11+ messages in thread
From: Jeff Garzik @ 2001-06-01 5:20 UTC (permalink / raw)
To: thunder7; +Cc: Manfred Spraul, linux-kernel
Looking at the diff of "lspci -vvvxxx" between MPS1.1 and MPS1.4 (on the
same system) may be quite useful... maybe I missed the earlier "lspci
-vvvxxx", but I only see one here...
--
Jeff Garzik | Disbelief, that's why you fail.
Building 1024 |
MandrakeSoft |
^ permalink raw reply [flat|nested] 11+ messages in thread
* Re: interrupt problem with MPS 1.4 / not with MPS 1.1 ?
2001-06-01 5:20 ` Jeff Garzik
@ 2001-06-01 5:39 ` thunder7
0 siblings, 0 replies; 11+ messages in thread
From: thunder7 @ 2001-06-01 5:39 UTC (permalink / raw)
To: Jeff Garzik; +Cc: linux-kernel
On Fri, Jun 01, 2001 at 01:20:23AM -0400, Jeff Garzik wrote:
> Looking at the diff of "lspci -vvvxxx" between MPS1.1 and MPS1.4 (on the
> same system) may be quite useful... maybe I missed the earlier "lspci
> -vvvxxx", but I only see one here...
Yep, I didn't want to keep sending long messages. Here goes:
diff pci_11 pci_14:
--
4c4
< Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR+
---
> Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR-
I see, this isn't going to work.
I'll insert the complete dump from mps 1.1 here, followed by the same
from 1.4:
00:00.0 Host bridge: VIA Technologies, Inc. VT82C693A/694x [Apollo PRO133x] (rev c4)
Subsystem: ABIT Computer Corp.: Unknown device a204
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR+
Latency: 8
Region 0: Memory at d0000000 (32-bit, prefetchable) [size=64M]
Capabilities: [a0] AGP version 2.0
Status: RQ=31 SBA+ 64bit- FW- Rate=x1,x2
Command: RQ=0 SBA- AGP- 64bit- FW- Rate=<none>
Capabilities: [c0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00: 06 11 91 06 06 00 10 a2 c4 00 00 06 00 08 00 00
10: 08 00 00 d0 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 7b 14 04 a2
30: 00 00 00 00 a0 00 00 00 00 00 00 00 00 00 00 00
00:01.0 PCI bridge: VIA Technologies, Inc. VT82C598/694x [Apollo MVP3/Pro133x AGP] (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR-
Latency: 0
Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
I/O behind bridge: 0000f000-00000fff
Memory behind bridge: d6000000-d8ffffff
Prefetchable memory behind bridge: d4000000-d5ffffff
BridgeCtl: Parity- SERR- NoISA+ VGA+ MAbort- >Reset- FastB2B-
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1+ D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00: 06 11 98 85 07 00 30 22 00 00 04 06 00 00 01 00
10: 00 00 00 00 00 00 00 00 00 01 01 00 f0 00 00 00
20: 00 d6 f0 d8 00 d4 f0 d5 00 00 00 00 00 00 00 00
30: 00 00 00 00 80 00 00 00 00 00 00 00 00 00 0c 00
00:07.0 ISA bridge: VIA Technologies, Inc. VT82C686 [Apollo Super South] (rev 40)
Subsystem: ABIT Computer Corp.: Unknown device 0000
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping+ SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Capabilities: [c0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00: 06 11 86 06 87 00 10 02 40 00 01 06 00 00 80 00
10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 7b 14 00 00
30: 00 00 00 00 c0 00 00 00 00 00 00 00 00 00 00 00
00:07.1 IDE interface: VIA Technologies, Inc. Bus Master IDE (rev 06) (prog-if 8a [Master SecP PriP])
Subsystem: VIA Technologies, Inc. Bus Master IDE
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32
Region 4: I/O ports at a800 [size=16]
Capabilities: [c0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00: 06 11 71 05 07 00 90 02 06 8a 01 01 00 20 00 00
10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
20: 01 a8 00 00 00 00 00 00 00 00 00 00 06 11 71 05
30: 00 00 00 00 c0 00 00 00 00 00 00 00 ff 00 00 00
00:07.2 USB Controller: VIA Technologies, Inc. UHCI USB (rev 16) (prog-if 00 [UHCI])
Subsystem: Unknown device 0925:1234
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32, cache line size 08
Interrupt: pin D routed to IRQ 5
Region 4: I/O ports at a000 [size=32]
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00: 06 11 38 30 07 00 10 02 16 00 03 0c 08 20 00 00
10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
20: 01 a0 00 00 00 00 00 00 00 00 00 00 25 09 34 12
30: 00 00 00 00 80 00 00 00 00 00 00 00 05 04 00 00
00:07.3 USB Controller: VIA Technologies, Inc. UHCI USB (rev 16) (prog-if 00 [UHCI])
Subsystem: Unknown device 0925:1234
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32, cache line size 08
Interrupt: pin D routed to IRQ 5
Region 4: I/O ports at a400 [size=32]
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00: 06 11 38 30 07 00 10 02 16 00 03 0c 08 20 00 00
10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
20: 01 a4 00 00 00 00 00 00 00 00 00 00 25 09 34 12
30: 00 00 00 00 80 00 00 00 00 00 00 00 05 04 00 00
00:07.4 Bridge: VIA Technologies, Inc. VT82C686 [Apollo Super ACPI] (rev 40)
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin ? routed to IRQ 3
Capabilities: [68] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00: 06 11 57 30 00 00 90 02 40 00 80 06 00 00 00 00
10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
30: 00 00 00 00 68 00 00 00 00 00 00 00 00 00 00 00
00:09.0 PCI bridge: Digital Equipment Corporation DECchip 21152 (rev 02) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32, cache line size 08
Bus: primary=00, secondary=02, subordinate=02, sec-latency=32
I/O behind bridge: 00009000-00009fff
Memory behind bridge: d9000000-daffffff
Prefetchable memory behind bridge: 00000000fff00000-0000000000000000
BridgeCtl: Parity- SERR+ NoISA+ VGA- MAbort- >Reset- FastB2B-
00: 11 10 24 00 07 01 80 02 02 00 04 06 08 20 01 00
10: 00 00 00 00 00 00 00 00 00 02 02 20 91 91 80 22
20: 00 d9 f0 da f1 ff 01 00 00 00 00 00 00 00 00 00
30: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 06 00
00:0a.0 SCSI storage controller: Symbios Logic Inc. (formerly NCR) 53c860 (rev 13)
Subsystem: Symbios Logic Inc. (formerly NCR): Unknown device 1000
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32 (2000ns min, 16000ns max), cache line size 08
Interrupt: pin A routed to IRQ 11
Region 0: I/O ports at ac00 [size=256]
Region 1: Memory at dc000000 (32-bit, non-prefetchable) [size=256]
Capabilities: [40] Power Management version 1
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00: 00 10 06 00 47 00 10 02 13 00 00 01 08 20 00 00
10: 01 ac 00 00 00 00 00 dc 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 00 10 00 10
30: 00 00 00 00 40 00 00 00 00 00 00 00 0b 01 08 40
00:0b.0 Multimedia audio controller: Creative Labs SB Live! EMU10000 (rev 07)
Subsystem: Creative Labs: Unknown device 8061
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32 (500ns min, 5000ns max)
Interrupt: pin A routed to IRQ 11
Region 0: I/O ports at b000 [size=32]
Capabilities: [dc] Power Management version 1
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00: 02 11 02 00 05 00 90 02 07 00 01 04 00 20 80 00
10: 01 b0 00 00 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 02 11 61 80
30: 00 00 00 00 dc 00 00 00 00 00 00 00 0b 01 02 14
00:0b.1 Input device controller: Creative Labs SB Live! (rev 07)
Subsystem: Creative Labs Gameport Joystick
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32
Region 0: I/O ports at b400 [size=8]
Capabilities: [dc] Power Management version 1
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00: 02 11 02 70 05 00 90 02 07 00 80 09 00 20 80 00
10: 01 b4 00 00 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 02 11 20 00
30: 00 00 00 00 dc 00 00 00 00 00 00 00 00 00 00 00
00:0e.0 Unknown mass storage controller: Triones Technologies, Inc. HPT366 (rev 03)
Subsystem: Triones Technologies, Inc.: Unknown device 0001
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 120 (2000ns min, 2000ns max), cache line size 08
Interrupt: pin A routed to IRQ 10
Region 0: I/O ports at b800 [size=8]
Region 1: I/O ports at bc00 [size=4]
Region 2: I/O ports at c000 [size=8]
Region 3: I/O ports at c400 [size=4]
Region 4: I/O ports at c800 [size=256]
Expansion ROM at <unassigned> [disabled] [size=128K]
Capabilities: [60] Power Management version 2
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00: 03 11 04 00 05 00 30 02 03 00 80 01 08 78 00 00
10: 01 b8 00 00 01 bc 00 00 01 c0 00 00 01 c4 00 00
20: 01 c8 00 00 00 00 00 00 00 00 00 00 03 11 01 00
30: 00 00 00 00 60 00 00 00 00 00 00 00 0a 01 08 08
01:00.0 VGA compatible controller: Matrox Graphics, Inc. MGA G400 AGP (rev 03) (prog-if 00 [VGA])
Subsystem: Matrox Graphics, Inc. Millennium G400 32Mb SGRAM
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32 (4000ns min, 8000ns max), cache line size 08
Interrupt: pin A routed to IRQ 15
Region 0: Memory at d4000000 (32-bit, prefetchable) [size=32M]
Region 1: Memory at d6000000 (32-bit, non-prefetchable) [size=16K]
Region 2: Memory at d7000000 (32-bit, non-prefetchable) [size=8M]
Expansion ROM at <unassigned> [disabled] [size=64K]
Capabilities: [dc] Power Management version 2
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [f0] AGP version 2.0
Status: RQ=31 SBA+ 64bit- FW- Rate=x1,x2
Command: RQ=31 SBA+ AGP+ 64bit- FW- Rate=x1
00: 2b 10 25 05 07 00 90 02 03 00 00 03 08 20 00 00
10: 08 00 00 d4 00 00 00 d6 00 00 00 d7 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 2b 10 f8 19
30: 00 00 00 00 dc 00 00 00 00 00 00 00 0f 01 10 20
02:00.0 SCSI storage controller: Symbios Logic Inc. (formerly NCR) 53c875 (rev 04)
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 72 (4250ns min, 16000ns max), cache line size 08
Interrupt: pin A routed to IRQ 15
Region 0: I/O ports at 9000 [size=256]
Region 1: Memory at da001000 (32-bit, non-prefetchable) [size=256]
Region 2: Memory at da000000 (32-bit, non-prefetchable) [size=4K]
Expansion ROM at <unassigned> [disabled] [size=64K]
00: 00 10 0f 00 47 00 00 02 04 00 00 01 08 48 00 00
10: 01 90 00 00 00 10 00 da 00 00 00 da 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
30: 00 00 00 00 00 00 00 00 00 00 00 00 0f 01 11 40
02:01.0 SCSI storage controller: Symbios Logic Inc. (formerly NCR) 53c875 (rev 04)
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 72 (4250ns min, 16000ns max), cache line size 08
Interrupt: pin A routed to IRQ 11
Region 0: I/O ports at 9400 [size=256]
Region 1: Memory at da002000 (32-bit, non-prefetchable) [size=256]
Region 2: Memory at da003000 (32-bit, non-prefetchable) [size=4K]
Expansion ROM at <unassigned> [disabled] [size=64K]
00: 00 10 0f 00 47 00 00 02 04 00 00 01 08 48 00 00
10: 01 94 00 00 00 20 00 da 00 30 00 da 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
30: 00 00 00 00 00 00 00 00 00 00 00 00 0b 01 11 40
02:02.0 Ethernet controller: Digital Equipment Corporation DECchip 21140 [FasterNet] (rev 22)
Subsystem: Digital Equipment Corporation: Unknown device 500a
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 96 (5000ns min, 10000ns max), cache line size 08
Interrupt: pin A routed to IRQ 10
Region 0: I/O ports at 9800 [size=128]
Region 1: Memory at da004000 (32-bit, non-prefetchable) [size=128]
Expansion ROM at <unassigned> [disabled] [size=256K]
00: 11 10 09 00 07 00 80 02 22 00 00 02 08 60 00 00
10: 01 98 00 00 00 40 00 da 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 11 10 0a 50
30: 00 00 00 00 00 00 00 00 00 00 00 00 0a 01 14 28
from 1.4:
00:00.0 Host bridge: VIA Technologies, Inc. VT82C693A/694x [Apollo PRO133x] (rev c4)
Subsystem: ABIT Computer Corp.: Unknown device a204
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR-
Latency: 8
Region 0: Memory at d0000000 (32-bit, prefetchable) [size=64M]
Capabilities: [a0] AGP version 2.0
Status: RQ=31 SBA+ 64bit- FW- Rate=x1,x2
Command: RQ=0 SBA- AGP- 64bit- FW- Rate=<none>
Capabilities: [c0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00: 06 11 91 06 06 00 10 22 c4 00 00 06 00 08 00 00
10: 08 00 00 d0 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 7b 14 04 a2
30: 00 00 00 00 a0 00 00 00 00 00 00 00 00 00 00 00
00:01.0 PCI bridge: VIA Technologies, Inc. VT82C598/694x [Apollo MVP3/Pro133x AGP] (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR-
Latency: 0
Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
I/O behind bridge: 0000f000-00000fff
Memory behind bridge: d6000000-d8ffffff
Prefetchable memory behind bridge: d4000000-d5ffffff
BridgeCtl: Parity- SERR- NoISA+ VGA+ MAbort- >Reset- FastB2B-
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1+ D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00: 06 11 98 85 07 00 30 22 00 00 04 06 00 00 01 00
10: 00 00 00 00 00 00 00 00 00 01 01 00 f0 00 00 00
20: 00 d6 f0 d8 00 d4 f0 d5 00 00 00 00 00 00 00 00
30: 00 00 00 00 80 00 00 00 00 00 00 00 00 00 0c 00
00:07.0 ISA bridge: VIA Technologies, Inc. VT82C686 [Apollo Super South] (rev 40)
Subsystem: ABIT Computer Corp.: Unknown device 0000
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping+ SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Capabilities: [c0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00: 06 11 86 06 87 00 10 02 40 00 01 06 00 00 80 00
10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 7b 14 00 00
30: 00 00 00 00 c0 00 00 00 00 00 00 00 00 00 00 00
00:07.1 IDE interface: VIA Technologies, Inc. Bus Master IDE (rev 06) (prog-if 8a [Master SecP PriP])
Subsystem: VIA Technologies, Inc. Bus Master IDE
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32
Region 4: I/O ports at a800 [size=16]
Capabilities: [c0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00: 06 11 71 05 07 00 90 02 06 8a 01 01 00 20 00 00
10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
20: 01 a8 00 00 00 00 00 00 00 00 00 00 06 11 71 05
30: 00 00 00 00 c0 00 00 00 00 00 00 00 ff 00 00 00
00:07.2 USB Controller: VIA Technologies, Inc. UHCI USB (rev 16) (prog-if 00 [UHCI])
Subsystem: Unknown device 0925:1234
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32, cache line size 08
Interrupt: pin D routed to IRQ 19
Region 4: I/O ports at a000 [size=32]
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00: 06 11 38 30 07 00 10 02 16 00 03 0c 08 20 00 00
10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
20: 01 a0 00 00 00 00 00 00 00 00 00 00 25 09 34 12
30: 00 00 00 00 80 00 00 00 00 00 00 00 05 04 00 00
00:07.3 USB Controller: VIA Technologies, Inc. UHCI USB (rev 16) (prog-if 00 [UHCI])
Subsystem: Unknown device 0925:1234
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32, cache line size 08
Interrupt: pin D routed to IRQ 19
Region 4: I/O ports at a400 [size=32]
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00: 06 11 38 30 07 00 10 02 16 00 03 0c 08 20 00 00
10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
20: 01 a4 00 00 00 00 00 00 00 00 00 00 25 09 34 12
30: 00 00 00 00 80 00 00 00 00 00 00 00 05 04 00 00
00:07.4 Bridge: VIA Technologies, Inc. VT82C686 [Apollo Super ACPI] (rev 40)
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin ? routed to IRQ 3
Capabilities: [68] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00: 06 11 57 30 00 00 90 02 40 00 80 06 00 00 00 00
10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
30: 00 00 00 00 68 00 00 00 00 00 00 00 00 00 00 00
00:09.0 PCI bridge: Digital Equipment Corporation DECchip 21152 (rev 02) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32, cache line size 08
Bus: primary=00, secondary=02, subordinate=02, sec-latency=32
I/O behind bridge: 00009000-00009fff
Memory behind bridge: d9000000-daffffff
Prefetchable memory behind bridge: 00000000fff00000-0000000000000000
BridgeCtl: Parity- SERR+ NoISA+ VGA- MAbort- >Reset- FastB2B-
00: 11 10 24 00 07 01 80 02 02 00 04 06 08 20 01 00
10: 00 00 00 00 00 00 00 00 00 02 02 20 91 91 80 22
20: 00 d9 f0 da f1 ff 01 00 00 00 00 00 00 00 00 00
30: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 06 00
00:0a.0 SCSI storage controller: Symbios Logic Inc. (formerly NCR) 53c860 (rev 13)
Subsystem: Symbios Logic Inc. (formerly NCR): Unknown device 1000
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32 (2000ns min, 16000ns max), cache line size 08
Interrupt: pin A routed to IRQ 17
Region 0: I/O ports at ac00 [size=256]
Region 1: Memory at dc000000 (32-bit, non-prefetchable) [size=256]
Capabilities: [40] Power Management version 1
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00: 00 10 06 00 47 00 10 02 13 00 00 01 08 20 00 00
10: 01 ac 00 00 00 00 00 dc 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 00 10 00 10
30: 00 00 00 00 40 00 00 00 00 00 00 00 0b 01 08 40
00:0b.0 Multimedia audio controller: Creative Labs SB Live! EMU10000 (rev 07)
Subsystem: Creative Labs: Unknown device 8061
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32 (500ns min, 5000ns max)
Interrupt: pin A routed to IRQ 17
Region 0: I/O ports at b000 [size=32]
Capabilities: [dc] Power Management version 1
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00: 02 11 02 00 05 00 90 02 07 00 01 04 00 20 80 00
10: 01 b0 00 00 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 02 11 61 80
30: 00 00 00 00 dc 00 00 00 00 00 00 00 0b 01 02 14
00:0b.1 Input device controller: Creative Labs SB Live! (rev 07)
Subsystem: Creative Labs Gameport Joystick
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32
Region 0: I/O ports at b400 [size=8]
Capabilities: [dc] Power Management version 1
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00: 02 11 02 70 05 00 90 02 07 00 80 09 00 20 80 00
10: 01 b4 00 00 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 02 11 20 00
30: 00 00 00 00 dc 00 00 00 00 00 00 00 00 00 00 00
00:0e.0 Unknown mass storage controller: Triones Technologies, Inc. HPT366 (rev 03)
Subsystem: Triones Technologies, Inc.: Unknown device 0001
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 120 (2000ns min, 2000ns max), cache line size 08
Interrupt: pin A routed to IRQ 18
Region 0: I/O ports at b800 [size=8]
Region 1: I/O ports at bc00 [size=4]
Region 2: I/O ports at c000 [size=8]
Region 3: I/O ports at c400 [size=4]
Region 4: I/O ports at c800 [size=256]
Expansion ROM at <unassigned> [disabled] [size=128K]
Capabilities: [60] Power Management version 2
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00: 03 11 04 00 05 00 30 02 03 00 80 01 08 78 00 00
10: 01 b8 00 00 01 bc 00 00 01 c0 00 00 01 c4 00 00
20: 01 c8 00 00 00 00 00 00 00 00 00 00 03 11 01 00
30: 00 00 00 00 60 00 00 00 00 00 00 00 0a 01 08 08
01:00.0 VGA compatible controller: Matrox Graphics, Inc. MGA G400 AGP (rev 03) (prog-if 00 [VGA])
Subsystem: Matrox Graphics, Inc. Millennium G400 32Mb SGRAM
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32 (4000ns min, 8000ns max), cache line size 08
Interrupt: pin A routed to IRQ 16
Region 0: Memory at d4000000 (32-bit, prefetchable) [size=32M]
Region 1: Memory at d6000000 (32-bit, non-prefetchable) [size=16K]
Region 2: Memory at d7000000 (32-bit, non-prefetchable) [size=8M]
Expansion ROM at <unassigned> [disabled] [size=64K]
Capabilities: [dc] Power Management version 2
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [f0] AGP version 2.0
Status: RQ=31 SBA+ 64bit- FW- Rate=x1,x2
Command: RQ=31 SBA+ AGP+ 64bit- FW- Rate=x1
00: 2b 10 25 05 07 00 90 02 03 00 00 03 08 20 00 00
10: 08 00 00 d4 00 00 00 d6 00 00 00 d7 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 2b 10 f8 19
30: 00 00 00 00 dc 00 00 00 00 00 00 00 0f 01 10 20
02:00.0 SCSI storage controller: Symbios Logic Inc. (formerly NCR) 53c875 (rev 04)
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 72 (4250ns min, 16000ns max), cache line size 08
Interrupt: pin A routed to IRQ 16
Region 0: I/O ports at 9000 [size=256]
Region 1: Memory at da001000 (32-bit, non-prefetchable) [size=256]
Region 2: Memory at da000000 (32-bit, non-prefetchable) [size=4K]
Expansion ROM at <unassigned> [disabled] [size=64K]
00: 00 10 0f 00 47 00 00 02 04 00 00 01 08 48 00 00
10: 01 90 00 00 00 10 00 da 00 00 00 da 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
30: 00 00 00 00 00 00 00 00 00 00 00 00 0f 01 11 40
02:01.0 SCSI storage controller: Symbios Logic Inc. (formerly NCR) 53c875 (rev 04)
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 72 (4250ns min, 16000ns max), cache line size 08
Interrupt: pin A routed to IRQ 17
Region 0: I/O ports at 9400 [size=256]
Region 1: Memory at da002000 (32-bit, non-prefetchable) [size=256]
Region 2: Memory at da003000 (32-bit, non-prefetchable) [size=4K]
Expansion ROM at <unassigned> [disabled] [size=64K]
00: 00 10 0f 00 47 00 00 02 04 00 00 01 08 48 00 00
10: 01 94 00 00 00 20 00 da 00 30 00 da 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
30: 00 00 00 00 00 00 00 00 00 00 00 00 0b 01 11 40
02:02.0 Ethernet controller: Digital Equipment Corporation DECchip 21140 [FasterNet] (rev 22)
Subsystem: Digital Equipment Corporation: Unknown device 500a
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 96 (5000ns min, 10000ns max), cache line size 08
Interrupt: pin A routed to IRQ 18
Region 0: I/O ports at 9800 [size=128]
Region 1: Memory at da004000 (32-bit, non-prefetchable) [size=128]
Expansion ROM at <unassigned> [disabled] [size=256K]
00: 11 10 09 00 07 00 80 02 22 00 00 02 08 60 00 00
10: 01 98 00 00 00 40 00 da 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 11 10 0a 50
30: 00 00 00 00 00 00 00 00 00 00 00 00 0a 01 14 28
Good luck,
Jurriaan
--
BOFH excuse #175:
OS swapped to disk
GNU/Linux 2.4.5-ac5 SMP/ReiserFS 2x1402 bogomips load av: 0.00 0.00 0.00
^ permalink raw reply [flat|nested] 11+ messages in thread
* Re: interrupt problem with MPS 1.4 / not with MPS 1.1 ?
2001-05-31 18:56 ` Greg KH
@ 2001-06-01 8:51 ` thunder7
0 siblings, 0 replies; 11+ messages in thread
From: thunder7 @ 2001-06-01 8:51 UTC (permalink / raw)
To: Greg KH; +Cc: linux-kernel
On Thu, May 31, 2001 at 11:56:44AM -0700, Greg KH wrote:
> Is the BIOS set to "Plug and Play supported OS" somewhere? If not, try
> enabling it.
>
It wasn't set, but with it set there is no difference.
Greetings,
Jurriaan
--
IF MICROSOFT BUILT CARS......
New seats would force everyone to have the same size butt.
GNU/Linux 2.4.5-ac5 SMP/ReiserFS 2x1402 bogomips load av: 0.87 0.42 0.16
^ permalink raw reply [flat|nested] 11+ messages in thread
* Re: interrupt problem with MPS 1.4 / not with MPS 1.1 ?
2001-06-01 5:14 ` thunder7
2001-06-01 5:20 ` Jeff Garzik
@ 2001-06-01 17:28 ` Manfred Spraul
2001-06-01 17:41 ` Jeff Garzik
2001-06-01 19:03 ` thunder7
1 sibling, 2 replies; 11+ messages in thread
From: Manfred Spraul @ 2001-06-01 17:28 UTC (permalink / raw)
To: thunder7; +Cc: linux-kernel, Jeff Garzik
thunder7@xs4all.nl wrote:
>
> :setpci -s 00:07.2 INTERRUPT_LINE=15
> :lspci -vx -s 00:07.2
> 00:07.2 USB Controller: VIA Technologies, Inc. UHCI USB (rev 16) (prog-if 00 [UHCI])
> Subsystem: Unknown device 0925:1234
> Flags: bus master, medium devsel, latency 32, IRQ 19
> I/O ports at a000 [size=32]
> Capabilities: [80] Power Management version 2
> 30: 00 00 00 00 80 00 00 00 00 00 00 00 15 04 00
> :setpci -s 00:07.2 INTERRUPT_LINE=19
> :lspci -vx -s 00:07.2
> 00:07.2 USB Controller: VIA Technologies, Inc. UHCI USB (rev 16) (prog-if 00 [UHCI])
> Subsystem: Unknown device 0925:1234
> Flags: bus master, medium devsel, latency 32, IRQ 19
> I/O ports at a000 [size=32]
> Capabilities: [80] Power Management version 2
> 30: 00 00 00 00 80 00 00 00 00 00 00 00 19 04 00 00
>
> So that is correct. I'll attach all the information from the MPS 1.4
> reboot, in which 00:07.2 happily points at 05, while everything else
> thinks it's at 19.....
>
Could you compile uhci as a module, set the configuration to MPS1.4 and
find out with which interrupt line setting it works.
I'd try both
setpci -s 00:07.2 INTERRUPT_LINE=13
setpci -s 00:07.2 INTERRUPT_LINE=3
[even if 13 works, please try 03 as well. 13 is hexadecimal==19]
The via ac97 sound driver contains an irq fixup for this problem. Either
a similar fixup is necessary in the uhci driver, or the fixup from the
ac97 driver could be moved to the pci-quirks and applied to all devices
in the southbridge.
--
Manfred
^ permalink raw reply [flat|nested] 11+ messages in thread
* Re: interrupt problem with MPS 1.4 / not with MPS 1.1 ?
2001-06-01 17:28 ` Manfred Spraul
@ 2001-06-01 17:41 ` Jeff Garzik
2001-06-01 19:03 ` thunder7
1 sibling, 0 replies; 11+ messages in thread
From: Jeff Garzik @ 2001-06-01 17:41 UTC (permalink / raw)
To: Manfred Spraul; +Cc: thunder7, linux-kernel
Manfred Spraul wrote:
> Could you compile uhci as a module, set the configuration to MPS1.4 and
> find out with which interrupt line setting it works.
> I'd try both
>
> setpci -s 00:07.2 INTERRUPT_LINE=13
> setpci -s 00:07.2 INTERRUPT_LINE=3
> [even if 13 works, please try 03 as well. 13 is hexadecimal==19]
>
> The via ac97 sound driver contains an irq fixup for this problem. Either
I am not sure this fixup is necessary, though IIRC it did solve some
problems. Since this latest round of Via fixups, I would like to remove
that little change in via audio, and see it anyone complains.
The 686A and 686B docs list no irq after 14. Adrian Cox has said that
setting the PCI intr line value actually makes a connection on the PIC,
instead of just being a scratchpad register like it is normally. Adrian
said the same thing about the USB IRQ, and I presume the other internal
irqs (like ACPI) listed for register 0x58 apply as well.
--
Jeff Garzik | Disbelief, that's why you fail.
Building 1024 |
MandrakeSoft |
^ permalink raw reply [flat|nested] 11+ messages in thread
* Re: interrupt problem with MPS 1.4 / not with MPS 1.1 ?
2001-06-01 17:28 ` Manfred Spraul
2001-06-01 17:41 ` Jeff Garzik
@ 2001-06-01 19:03 ` thunder7
1 sibling, 0 replies; 11+ messages in thread
From: thunder7 @ 2001-06-01 19:03 UTC (permalink / raw)
To: Manfred Spraul; +Cc: linux-kernel, jgarzik
On Fri, Jun 01, 2001 at 07:28:33PM +0200, Manfred Spraul wrote:
> thunder7@xs4all.nl wrote:
> >
> > :setpci -s 00:07.2 INTERRUPT_LINE=15
> > :lspci -vx -s 00:07.2
> > 00:07.2 USB Controller: VIA Technologies, Inc. UHCI USB (rev 16) (prog-if 00 [UHCI])
> > Subsystem: Unknown device 0925:1234
> > Flags: bus master, medium devsel, latency 32, IRQ 19
> > I/O ports at a000 [size=32]
> > Capabilities: [80] Power Management version 2
> > 30: 00 00 00 00 80 00 00 00 00 00 00 00 15 04 00
> > :setpci -s 00:07.2 INTERRUPT_LINE=19
> > :lspci -vx -s 00:07.2
> > 00:07.2 USB Controller: VIA Technologies, Inc. UHCI USB (rev 16) (prog-if 00 [UHCI])
> > Subsystem: Unknown device 0925:1234
> > Flags: bus master, medium devsel, latency 32, IRQ 19
> > I/O ports at a000 [size=32]
> > Capabilities: [80] Power Management version 2
> > 30: 00 00 00 00 80 00 00 00 00 00 00 00 19 04 00 00
> >
> > So that is correct. I'll attach all the information from the MPS 1.4
> > reboot, in which 00:07.2 happily points at 05, while everything else
> > thinks it's at 19.....
> >
>
> Could you compile uhci as a module, set the configuration to MPS1.4 and
> find out with which interrupt line setting it works.
> I'd try both
>
> setpci -s 00:07.2 INTERRUPT_LINE=13
no change, still this in /var/log/messages:
Jun 1 20:57:48 middle kernel: uhci.c: USB Universal Host Controller Interface driver
Jun 1 20:57:48 middle kernel: hub.c: USB new device connect on bus1/1, assigned device number 2
Jun 1 20:57:51 middle kernel: usb_control/bulk_msg: timeout
Jun 1 20:57:51 middle kernel: usb.c: USB device not accepting new address=2 (error=-110)
Jun 1 20:57:51 middle kernel: hub.c: USB new device connect on bus1/1, assigned device number 3
Jun 1 20:57:54 middle kernel: usb_control/bulk_msg: timeout
Jun 1 20:57:54 middle kernel: usb.c: USB device not accepting new address=3 (error=-110)
> setpci -s 00:07.2 INTERRUPT_LINE=3
> [even if 13 works, please try 03 as well. 13 is hexadecimal==19]
Bingo!!
Jun 1 20:59:34 middle kernel: Type: Direct-Access ANSI SCSI revision: 02
Jun 1 20:59:34 middle kernel: Attached scsi removable disk sda at scsi3, channel 0, id 0, lun 0
Jun 1 20:59:34 middle kernel: sda : READ CAPACITY failed.
Jun 1 20:59:34 middle kernel: sda : status = 1, message = 00, host = 0, driver = 08
Jun 1 20:59:34 middle kernel: sda : extended sense code = 2
Jun 1 20:59:34 middle kernel: sda : block size assumed to be 512 bytes, disk size 1GB.
Jun 1 20:59:34 middle kernel: sda: I/O error: dev 08:00, sector 0
Jun 1 20:59:34 middle kernel: unable to read partition table
Jun 1 20:59:34 middle kernel: WARNING: USB Mass Storage data integrity not assured
Jun 1 20:59:34 middle kernel: USB Mass Storage device found at 2
>
> The via ac97 sound driver contains an irq fixup for this problem. Either
> a similar fixup is necessary in the uhci driver, or the fixup from the
> ac97 driver could be moved to the pci-quirks and applied to all devices
> in the southbridge.
>
Just to be sure, the lspci -vvvxxx reading of 07.2 after this setpci -s
00:07.2 INTERRUPT_LINE=3 with MPS=1.4 in the bios:
00:07.2 USB Controller: VIA Technologies, Inc. UHCI USB (rev 16) (prog-if 00 [UHCI])
Subsystem: Unknown device 0925:1234
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32, cache line size 08
Interrupt: pin D routed to IRQ 19
Region 4: I/O ports at a000 [size=32]
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00: 06 11 38 30 07 00 10 02 16 00 03 0c 08 20 00 00
10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
20: 01 a0 00 00 00 00 00 00 00 00 00 00 25 09 34 12
30: 00 00 00 00 80 00 00 00 00 00 00 00 03 04 00 00
40: 00 10 03 00 02 00 32 e0 00 00 00 00 00 00 00 00
50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
60: 10 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
80: 01 00 02 00 00 00 00 00 00 00 00 00 00 00 00 00
90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
c0: 00 20 00 00 00 00 00 00 00 00 00 00 00 00 00 00
d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
/proc/interrupts:
CPU0 CPU1
0: 22004 24207 IO-APIC-edge timer
1: 2073 2617 IO-APIC-edge keyboard
2: 0 0 XT-PIC cascade
8: 2 0 IO-APIC-edge rtc
14: 240 241 IO-APIC-edge ide0
16: 5342007 5342450 IO-APIC-level sym53c8xx
17: 23 21 IO-APIC-level sym53c8xx, sym53c8xx
18: 6448 6349 IO-APIC-level ide2, ide3, DE500-AA (eth0)
19: 42 42 IO-APIC-level usb-uhci, usb-uhci
NMI: 0 0
LOC: 46131 46128
ERR: 0
MIS: 0
Good luck,
Jurriaan
--
BOFH excuse #317:
Internet exceeded Luser level, please wait until a luser
logs off before attempting to log back on.
GNU/Linux 2.4.5-ac6 SMP/ReiserFS 2x1402 bogomips load av: 0.49 0.12 0.04
^ permalink raw reply [flat|nested] 11+ messages in thread
end of thread, other threads:[~2001-06-01 19:04 UTC | newest]
Thread overview: 11+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
2001-05-31 18:39 interrupt problem with MPS 1.4 / not with MPS 1.1 ? thunder7
2001-05-31 18:06 ` Greg KH
2001-05-31 19:48 ` [lkml]Re: " thunder7
2001-05-31 18:56 ` Greg KH
2001-06-01 8:51 ` thunder7
-- strict thread matches above, loose matches on Subject: below --
2001-05-31 20:21 [lkml]Re: " Manfred Spraul
2001-05-31 20:27 ` [lkml]Re: " thunder7
2001-05-31 20:45 ` Manfred Spraul
2001-06-01 5:14 ` thunder7
2001-06-01 5:20 ` Jeff Garzik
2001-06-01 5:39 ` thunder7
2001-06-01 17:28 ` Manfred Spraul
2001-06-01 17:41 ` Jeff Garzik
2001-06-01 19:03 ` thunder7
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox