* interrupt problem with MPS 1.4 / not with MPS 1.1 ? @ 2001-05-31 18:39 thunder7 2001-05-31 18:06 ` Greg KH 0 siblings, 1 reply; 11+ messages in thread From: thunder7 @ 2001-05-31 18:39 UTC (permalink / raw) To: linux-kernel Hardware: Abit VP6 (Via 694x) x86/SMP motherboard with USB controller If I set the bios for MPS 1.1, USB runs fine. If I set the bios for MPS 1.4, I get this: May 31 13:08:06 middle kernel: hub.c: USB new device connect on bus1/1, assigned device number 4 May 31 13:08:09 middle kernel: usb_control/bulk_msg: timeout May 31 13:08:09 middle kernel: usb.c: USB device not accepting new address=4 (error=-110) May 31 13:08:09 middle kernel: hub.c: USB new device connect on bus1/1, assigned device number 5 May 31 13:08:12 middle kernel: usb_control/bulk_msg: timeout May 31 13:08:12 middle kernel: usb.c: USB device not accepting new address=5 (error=-110) May 31 13:08:12 middle kernel: hub.c: USB new device connect on bus1/1, assigned device number 6 May 31 13:08:15 middle kernel: usb_control/bulk_msg: timeout May 31 13:08:15 middle kernel: usb.c: USB device not accepting new address=6 (error=-110) May 31 13:08:16 middle kernel: hub.c: USB new device connect on bus1/1, assigned device number 7 May 31 13:08:19 middle kernel: usb_control/bulk_msg: timeout May 31 13:08:19 middle kernel: usb.c: USB device not accepting new address=7 (error=-110) May 31 13:08:19 middle kernel: hub.c: USB new device connect on bus1/1, assigned device number 8 May 31 13:08:22 middle kernel: usb_control/bulk_msg: timeout May 31 13:08:22 middle kernel: usb.c: USB device not accepting new address=8 (error=-110) May 31 13:08:22 middle kernel: hub.c: USB new device connect on bus1/1, assigned device number 9 Now I understand this mail doesn't have all the necessary info, but my question is: What information would be necessary to debug this? dmesg /var/log/messages lspci -vv (or -x?) or more? Jurriaan -- BOFH excuse #57: Groundskeepers stole the root password GNU/Linux 2.4.5-ac4 SMP/ReiserFS 2x1402 bogomips load av: 0.41 0.11 0.03 ^ permalink raw reply [flat|nested] 11+ messages in thread
* Re: interrupt problem with MPS 1.4 / not with MPS 1.1 ? 2001-05-31 18:39 interrupt problem with MPS 1.4 / not with MPS 1.1 ? thunder7 @ 2001-05-31 18:06 ` Greg KH 2001-05-31 19:48 ` [lkml]Re: " thunder7 0 siblings, 1 reply; 11+ messages in thread From: Greg KH @ 2001-05-31 18:06 UTC (permalink / raw) To: thunder7; +Cc: linux-kernel On Thu, May 31, 2001 at 08:39:08PM +0200, thunder7@xs4all.nl wrote: > What information would be necessary to debug this? Which kernel version? greg k-h ^ permalink raw reply [flat|nested] 11+ messages in thread
* Re: [lkml]Re: interrupt problem with MPS 1.4 / not with MPS 1.1 ? 2001-05-31 18:06 ` Greg KH @ 2001-05-31 19:48 ` thunder7 2001-05-31 18:56 ` Greg KH 0 siblings, 1 reply; 11+ messages in thread From: thunder7 @ 2001-05-31 19:48 UTC (permalink / raw) To: Greg KH; +Cc: linux-kernel On Thu, May 31, 2001 at 11:06:42AM -0700, Greg KH wrote: > On Thu, May 31, 2001 at 08:39:08PM +0200, thunder7@xs4all.nl wrote: > > What information would be necessary to debug this? > > Which kernel version? > > greg k-h > 2.4.5-ac4, but I rebooted in 2.4.4 and it did the same. I'll try and add some info here (from the bios= MPS 1.1 case!) I have the following expansion cards: Matrox G400 agp video-card ITI 4280 dual-UW scsi + fast ethernet card NCR860 ultra-scsi card Soundblaster Live! 5.1 card from dmesg: Total of 2 processors activated (2808.21 BogoMIPS). ENABLING IO-APIC IRQs ...changing IO-APIC physical APIC ID to 2 ... ok. init IO_APIC IRQs IO-APIC (apicid-pin) 2-0, 2-16, 2-17, 2-18, 2-19, 2-20, 2-21, 2-22, 2-23 not connected. ..TIMER: vector=49 pin1=2 pin2=0 number of MP IRQ sources: 16. number of IO-APIC #2 registers: 24. testing the IO APIC....................... IO APIC #2...... .... register #00: 02000000 ....... : physical APIC id: 02 .... register #01: 00178011 ....... : max redirection entries: 0017 ....... : IO APIC version: 0011 WARNING: unexpected IO-APIC, please mail to linux-smp@vger.kernel.org .... register #02: 00000000 ....... : arbitration: 00 .... IRQ redirection table: NR Log Phy Mask Trig IRR Pol Stat Dest Deli Vect: 00 000 00 1 0 0 0 0 0 0 00 01 003 03 0 0 0 0 0 1 1 39 02 003 03 0 0 0 0 0 1 1 31 03 003 03 0 0 0 0 0 1 1 41 04 003 03 0 0 0 0 0 1 1 49 05 003 03 1 1 0 1 0 1 1 51 06 003 03 0 0 0 0 0 1 1 59 07 003 03 0 0 0 0 0 1 1 61 08 003 03 0 0 0 0 0 1 1 69 09 003 03 0 0 0 0 0 1 1 71 0a 003 03 1 1 0 1 0 1 1 79 0b 003 03 1 1 0 1 0 1 1 81 0c 003 03 0 0 0 0 0 1 1 89 0d 003 03 0 0 0 0 0 1 1 91 0e 003 03 0 0 0 0 0 1 1 99 0f 003 03 1 1 0 1 0 1 1 A1 10 000 00 1 0 0 0 0 0 0 00 11 000 00 1 0 0 0 0 0 0 00 12 000 00 1 0 0 0 0 0 0 00 13 000 00 1 0 0 0 0 0 0 00 14 000 00 1 0 0 0 0 0 0 00 15 000 00 1 0 0 0 0 0 0 00 16 000 00 1 0 0 0 0 0 0 00 17 000 00 1 0 0 0 0 0 0 00 IRQ to pin mappings: IRQ0 -> 0:2 IRQ1 -> 0:1 IRQ3 -> 0:3 IRQ4 -> 0:4 IRQ5 -> 0:5 IRQ6 -> 0:6 IRQ7 -> 0:7 IRQ8 -> 0:8 IRQ9 -> 0:9 IRQ10 -> 0:10 IRQ11 -> 0:11 IRQ12 -> 0:12 IRQ13 -> 0:13 IRQ14 -> 0:14 IRQ15 -> 0:15 .................................... done. Using local APIC timer interrupts. calibrating APIC timer ... ..... CPU clock speed is 703.1338 MHz. ..... host bus clock speed is 100.4475 MHz. cpu: 0, clocks: 1004475, slice: 334825 CPU0<T0:1004464,T1:669632,D:7,S:334825,C:1004475> cpu: 1, clocks: 1004475, slice: 334825 CPU1<T0:1004464,T1:334800,D:14,S:334825,C:1004475> checking TSC synchronization across CPUs: passed. mtrr: your CPUs had inconsistent variable MTRR settings mtrr: probably your BIOS does not setup all CPUs PCI: PCI BIOS revision 2.10 entry at 0xfb3a0, last bus=2 PCI: Using configuration type 1 PCI: Probing PCI hardware Unknown bridge resource 0: assuming transparent Unknown bridge resource 2: assuming transparent PCI: Using IRQ router VIA [1106/0686] at 00:07.0 Linux NET4.0 for Linux 2.4 usb.c: registered new driver hub uhci.c: USB UHCI at I/O 0xa000, IRQ 5 usb.c: new USB bus registered, assigned bus number 1 hub.c: USB hub found hub.c: 2 ports detected uhci.c: USB UHCI at I/O 0xa400, IRQ 5 usb.c: new USB bus registered, assigned bus number 2 hub.c: USB hub found hub.c: 2 ports detected uhci.c: Linus Torvalds, Johannes Erdfelt, Randy Dunlap, Georg Acher, Deti Fliegl, Thomas Sailer, Roman Weissgaerber uhci.c: USB Universal Host Controller Interface driver Initializing USB Mass Storage driver... usb.c: registered new driver usb-storage USB Mass Storage support registered. NET4: Linux TCP/IP 1.0 for NET4.0 Freeing unused kernel memory: 248k freed hub.c: USB new device connect on bus1/1, assigned device number 2 scsi3 : SCSI emulation for USB Mass Storage devices Vendor: IOMEGA Model: ZIP 250 Rev: 61.T Type: Direct-Access ANSI SCSI revision: 02 Attached scsi removable disk sda at scsi3, channel 0, id 0, lun 0 sda : READ CAPACITY failed. sda : status = 1, message = 00, host = 0, driver = 08 sda : extended sense code = 2 sda : block size assumed to be 512 bytes, disk size 1GB. sda: I/O error: dev 08:00, sector 0 unable to read partition table WARNING: USB Mass Storage data integrity not assured USB Mass Storage device found at 2 Adding Swap: 1047776k swap-space (priority -1) from lspci: 00:00.0 Host bridge: VIA Technologies, Inc. VT82C693A/694x [Apollo PRO133x] (rev c4) Subsystem: ABIT Computer Corp.: Unknown device a204 Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR- Latency: 8 Region 0: Memory at d0000000 (32-bit, prefetchable) [size=64M] Capabilities: [a0] AGP version 2.0 Status: RQ=31 SBA+ 64bit- FW- Rate=x1,x2 Command: RQ=0 SBA- AGP- 64bit- FW- Rate=<none> Capabilities: [c0] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME- 00:01.0 PCI bridge: VIA Technologies, Inc. VT82C598/694x [Apollo MVP3/Pro133x AGP] (prog-if 00 [Normal decode]) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR- Latency: 0 Bus: primary=00, secondary=01, subordinate=01, sec-latency=0 Memory behind bridge: d6000000-d8ffffff Prefetchable memory behind bridge: d4000000-d5ffffff BridgeCtl: Parity- SERR- NoISA+ VGA+ MAbort- >Reset- FastB2B- Capabilities: [80] Power Management version 2 Flags: PMEClk- DSI- D1+ D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME- 00:07.0 ISA bridge: VIA Technologies, Inc. VT82C686 [Apollo Super South] (rev 40) Subsystem: ABIT Computer Corp.: Unknown device 0000 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping+ SERR- FastB2B- Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 0 Capabilities: [c0] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME- 00:07.1 IDE interface: VIA Technologies, Inc. Bus Master IDE (rev 06) (prog-if 8a [Master SecP PriP]) Subsystem: VIA Technologies, Inc. Bus Master IDE Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 32 Region 4: I/O ports at a800 [size=16] Capabilities: [c0] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME- 00:07.2 USB Controller: VIA Technologies, Inc. UHCI USB (rev 16) (prog-if 00 [UHCI]) Subsystem: Unknown device 0925:1234 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 32, cache line size 08 Interrupt: pin D routed to IRQ 5 Region 4: I/O ports at a000 [size=32] Capabilities: [80] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME- 00:07.3 USB Controller: VIA Technologies, Inc. UHCI USB (rev 16) (prog-if 00 [UHCI]) Subsystem: Unknown device 0925:1234 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 32, cache line size 08 Interrupt: pin D routed to IRQ 5 Region 4: I/O ports at a400 [size=32] Capabilities: [80] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME- 00:07.4 Bridge: VIA Technologies, Inc. VT82C686 [Apollo Super ACPI] (rev 40) Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Interrupt: pin ? routed to IRQ 3 Capabilities: [68] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME- 00:09.0 PCI bridge: Digital Equipment Corporation DECchip 21152 (rev 02) (prog-if 00 [Normal decode]) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 32, cache line size 08 Bus: primary=00, secondary=02, subordinate=02, sec-latency=32 I/O behind bridge: 00009000-00009fff Memory behind bridge: d9000000-daffffff BridgeCtl: Parity- SERR+ NoISA+ VGA- MAbort- >Reset- FastB2B- 00:0a.0 SCSI storage controller: Symbios Logic Inc. (formerly NCR) 53c860 (rev 13) Subsystem: Symbios Logic Inc. (formerly NCR): Unknown device 1000 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR- FastB2B- Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 32 (2000ns min, 16000ns max), cache line size 08 Interrupt: pin A routed to IRQ 11 Region 0: I/O ports at ac00 [size=256] Region 1: Memory at dc000000 (32-bit, non-prefetchable) [size=256] Capabilities: [40] Power Management version 1 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME- 00:0b.0 Multimedia audio controller: Creative Labs SB Live! EMU10000 (rev 07) Subsystem: Creative Labs: Unknown device 8061 Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 32 (500ns min, 5000ns max) Interrupt: pin A routed to IRQ 11 Region 0: I/O ports at b000 [size=32] Capabilities: [dc] Power Management version 1 Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME- 00:0b.1 Input device controller: Creative Labs SB Live! (rev 07) Subsystem: Creative Labs Gameport Joystick Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 32 Region 0: I/O ports at b400 [size=8] Capabilities: [dc] Power Management version 1 Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME- 00:0e.0 Unknown mass storage controller: Triones Technologies, Inc. HPT366 (rev 03) Subsystem: Triones Technologies, Inc.: Unknown device 0001 Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 120 (2000ns min, 2000ns max), cache line size 08 Interrupt: pin A routed to IRQ 10 Region 0: I/O ports at b800 [size=8] Region 1: I/O ports at bc00 [size=4] Region 2: I/O ports at c000 [size=8] Region 3: I/O ports at c400 [size=4] Region 4: I/O ports at c800 [size=256] Expansion ROM at <unassigned> [disabled] [size=128K] Capabilities: [60] Power Management version 2 Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME- 01:00.0 VGA compatible controller: Matrox Graphics, Inc. MGA G400 AGP (rev 03) (prog-if 00 [VGA]) Subsystem: Matrox Graphics, Inc. Millennium G400 32Mb SGRAM Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 32 (4000ns min, 8000ns max), cache line size 08 Interrupt: pin A routed to IRQ 15 Region 0: Memory at d4000000 (32-bit, prefetchable) [size=32M] Region 1: Memory at d6000000 (32-bit, non-prefetchable) [size=16K] Region 2: Memory at d7000000 (32-bit, non-prefetchable) [size=8M] Expansion ROM at <unassigned> [disabled] [size=64K] Capabilities: [dc] Power Management version 2 Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME- Capabilities: [f0] AGP version 2.0 Status: RQ=31 SBA+ 64bit- FW- Rate=x1,x2 Command: RQ=31 SBA+ AGP+ 64bit- FW- Rate=x1 02:00.0 SCSI storage controller: Symbios Logic Inc. (formerly NCR) 53c875 (rev 04) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR- FastB2B- Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 72 (4250ns min, 16000ns max), cache line size 08 Interrupt: pin A routed to IRQ 15 Region 0: I/O ports at 9000 [size=256] Region 1: Memory at da001000 (32-bit, non-prefetchable) [size=256] Region 2: Memory at da000000 (32-bit, non-prefetchable) [size=4K] Expansion ROM at <unassigned> [disabled] [size=64K] 02:01.0 SCSI storage controller: Symbios Logic Inc. (formerly NCR) 53c875 (rev 04) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR- FastB2B- Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 72 (4250ns min, 16000ns max), cache line size 08 Interrupt: pin A routed to IRQ 11 Region 0: I/O ports at 9400 [size=256] Region 1: Memory at da002000 (32-bit, non-prefetchable) [size=256] Region 2: Memory at da003000 (32-bit, non-prefetchable) [size=4K] Expansion ROM at <unassigned> [disabled] [size=64K] 02:02.0 Ethernet controller: Digital Equipment Corporation DECchip 21140 [FasterNet] (rev 22) Subsystem: Digital Equipment Corporation: Unknown device 500a Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 96 (5000ns min, 10000ns max), cache line size 08 Interrupt: pin A routed to IRQ 10 Region 0: I/O ports at 9800 [size=128] Region 1: Memory at da004000 (32-bit, non-prefetchable) [size=128] Expansion ROM at <unassigned> [disabled] [size=256K] I know that with MPS 1.4, the USB controller finds itself at an unshared interrupt 19. I can't reboot at the moment to check. Good luck, Jurriaan -- HORROR FILM WISDOM: 13. If you are using a gun to combat the all-consuming evil, it is a good idea to quickly find a new means of defense, because no matter how much ammo you have, you'll run out just before you kill the monster (unless your name is Ash, in which case, you'll never have to reload). GNU/Linux 2.4.5-ac4 SMP/ReiserFS 2x1402 bogomips load av: 0.06 0.03 0.00 ^ permalink raw reply [flat|nested] 11+ messages in thread
* Re: interrupt problem with MPS 1.4 / not with MPS 1.1 ? 2001-05-31 19:48 ` [lkml]Re: " thunder7 @ 2001-05-31 18:56 ` Greg KH 2001-06-01 8:51 ` thunder7 0 siblings, 1 reply; 11+ messages in thread From: Greg KH @ 2001-05-31 18:56 UTC (permalink / raw) To: thunder7; +Cc: linux-kernel On Thu, May 31, 2001 at 09:48:35PM +0200, thunder7@xs4all.nl wrote: > On Thu, May 31, 2001 at 11:06:42AM -0700, Greg KH wrote: > > On Thu, May 31, 2001 at 08:39:08PM +0200, thunder7@xs4all.nl wrote: > > > What information would be necessary to debug this? > > > > Which kernel version? > > > > greg k-h > > > 2.4.5-ac4, but I rebooted in 2.4.4 and it did the same. Is the BIOS set to "Plug and Play supported OS" somewhere? If not, try enabling it. Also the MPS 1.4 boot messages would be helpful :) thanks, greg k-h ^ permalink raw reply [flat|nested] 11+ messages in thread
* Re: interrupt problem with MPS 1.4 / not with MPS 1.1 ? 2001-05-31 18:56 ` Greg KH @ 2001-06-01 8:51 ` thunder7 0 siblings, 0 replies; 11+ messages in thread From: thunder7 @ 2001-06-01 8:51 UTC (permalink / raw) To: Greg KH; +Cc: linux-kernel On Thu, May 31, 2001 at 11:56:44AM -0700, Greg KH wrote: > Is the BIOS set to "Plug and Play supported OS" somewhere? If not, try > enabling it. > It wasn't set, but with it set there is no difference. Greetings, Jurriaan -- IF MICROSOFT BUILT CARS...... New seats would force everyone to have the same size butt. GNU/Linux 2.4.5-ac5 SMP/ReiserFS 2x1402 bogomips load av: 0.87 0.42 0.16 ^ permalink raw reply [flat|nested] 11+ messages in thread
* Re: [lkml]Re: interrupt problem with MPS 1.4 / not with MPS 1.1 ?
@ 2001-05-31 20:21 Manfred Spraul
2001-05-31 20:27 ` [lkml]Re: " thunder7
0 siblings, 1 reply; 11+ messages in thread
From: Manfred Spraul @ 2001-05-31 20:21 UTC (permalink / raw)
To: thunder7, linux-kernel
>
> I know that with MPS 1.4, the USB controller finds itself at an
> unshared interrupt 19. I can't reboot at the moment to check.
>
lspci -vxxx -s 00:07.0
the APIC sits in the southbridge.
the low 2 bits of offset 0x58 must be set [route USB IRQ to APIC], and
lspci -vx -s 00:07.2
offset 0x3C must be set to 3 [19 & 15]
There was some discussion about the same problem with the sound part of
the southbridge.
What are the current values of these registers?
--
Manfred
^ permalink raw reply [flat|nested] 11+ messages in thread* Re: [lkml]Re: [lkml]Re: interrupt problem with MPS 1.4 / not with MPS 1.1 ? 2001-05-31 20:21 [lkml]Re: " Manfred Spraul @ 2001-05-31 20:27 ` thunder7 2001-05-31 20:45 ` Manfred Spraul 0 siblings, 1 reply; 11+ messages in thread From: thunder7 @ 2001-05-31 20:27 UTC (permalink / raw) To: Manfred Spraul; +Cc: linux-kernel On Thu, May 31, 2001 at 10:21:55PM +0200, Manfred Spraul wrote: > > > > I know that with MPS 1.4, the USB controller finds itself at an > > unshared interrupt 19. I can't reboot at the moment to check. > > > lspci -vxxx -s 00:07.0 > > the APIC sits in the southbridge. > the low 2 bits of offset 0x58 must be set [route USB IRQ to APIC], and > > lspci -vx -s 00:07.2 > > offset 0x3C must be set to 3 [19 & 15] > > There was some discussion about the same problem with the sound part of > the southbridge. > > What are the current values of these registers? > current, as in MPS 1.1: 00:07.0 ISA bridge: VIA Technologies, Inc. VT82C686 [Apollo Super South] (rev 40) Subsystem: ABIT Computer Corp.: Unknown device 0000 Flags: bus master, stepping, medium devsel, latency 0 Capabilities: [c0] Power Management version 2 50: 02 76 04 00 00 f0 ab 50 1f 06 ff 08 00 00 00 00 I'd say the lower 2 bits at 0x58 are set. 00:07.2 USB Controller: VIA Technologies, Inc. UHCI USB (rev 16) (prog-if 00 [UHCI]) Subsystem: Unknown device 0925:1234 Flags: bus master, medium devsel, latency 32, IRQ 5 I/O ports at a000 [size=32] Capabilities: [80] Power Management version 2 30: 00 00 00 00 80 00 00 00 00 00 00 00 05 04 00 00 0x3X is at 5, not at 3. Greetings, Jurriaan -- Endora is where we are, and you need to know that describing this place is like dancing to no music. Peter Hedges - What's eating Gilbert Grape GNU/Linux 2.4.5-ac4 SMP/ReiserFS 2x1402 bogomips load av: 0.02 0.01 0.00 ^ permalink raw reply [flat|nested] 11+ messages in thread
* Re: [lkml]Re: [lkml]Re: interrupt problem with MPS 1.4 / not with MPS 1.1 ? 2001-05-31 20:27 ` [lkml]Re: " thunder7 @ 2001-05-31 20:45 ` Manfred Spraul 2001-06-01 5:14 ` thunder7 0 siblings, 1 reply; 11+ messages in thread From: Manfred Spraul @ 2001-05-31 20:45 UTC (permalink / raw) To: thunder7; +Cc: linux-kernel thunder7@xs4all.nl wrote: > > 00:07.2 USB Controller: VIA Technologies, Inc. UHCI USB (rev 16) (prog-if 00 [UHCI]) > Subsystem: Unknown device 0925:1234 > Flags: bus master, medium devsel, latency 32, IRQ 5 > I/O ports at a000 [size=32] > Capabilities: [80] Power Management version 2 > 30: 00 00 00 00 80 00 00 00 00 00 00 00 05 04 00 00 > > 0x3X is at 5, not at 3. > You still run with MPS 1.1. It should be 3 or 19 after you reboot with MPS 1.4. Could you please try the following commands as root, but just before rebooting. It'll kill the USB controller. #setpci -s 00:07.2 INTERRUPT_LINE=15 #lspci -vx -s 00:07.2 <<< 0x3C should be 15 #setpci -s 00:07.2 INTERRUPT_LINE=19 #lspci -vx -s 00:07.2 <<< 0x3C is now either 19 or 3 -- Manfred ^ permalink raw reply [flat|nested] 11+ messages in thread
* Re: interrupt problem with MPS 1.4 / not with MPS 1.1 ? 2001-05-31 20:45 ` Manfred Spraul @ 2001-06-01 5:14 ` thunder7 2001-06-01 5:20 ` Jeff Garzik 2001-06-01 17:28 ` Manfred Spraul 0 siblings, 2 replies; 11+ messages in thread From: thunder7 @ 2001-06-01 5:14 UTC (permalink / raw) To: Manfred Spraul; +Cc: linux-kernel On Thu, May 31, 2001 at 10:45:17PM +0200, Manfred Spraul wrote: > thunder7@xs4all.nl wrote: > > > > 00:07.2 USB Controller: VIA Technologies, Inc. UHCI USB (rev 16) (prog-if 00 [UHCI]) > > Subsystem: Unknown device 0925:1234 > > Flags: bus master, medium devsel, latency 32, IRQ 5 > > I/O ports at a000 [size=32] > > Capabilities: [80] Power Management version 2 > > 30: 00 00 00 00 80 00 00 00 00 00 00 00 05 04 00 00 > > > > 0x3X is at 5, not at 3. > > > You still run with MPS 1.1. > It should be 3 or 19 after you reboot with MPS 1.4. > > Could you please try the following commands as root, but just before > rebooting. It'll kill the USB controller. > > #setpci -s 00:07.2 INTERRUPT_LINE=15 > #lspci -vx -s 00:07.2 > <<< 0x3C should be 15 > #setpci -s 00:07.2 INTERRUPT_LINE=19 > #lspci -vx -s 00:07.2 > <<< 0x3C is now either 19 or 3 > :setpci -s 00:07.2 INTERRUPT_LINE=15 :lspci -vx -s 00:07.2 00:07.2 USB Controller: VIA Technologies, Inc. UHCI USB (rev 16) (prog-if 00 [UHCI]) Subsystem: Unknown device 0925:1234 Flags: bus master, medium devsel, latency 32, IRQ 19 I/O ports at a000 [size=32] Capabilities: [80] Power Management version 2 30: 00 00 00 00 80 00 00 00 00 00 00 00 15 04 00 00 :setpci -s 00:07.2 INTERRUPT_LINE=19 :lspci -vx -s 00:07.2 00:07.2 USB Controller: VIA Technologies, Inc. UHCI USB (rev 16) (prog-if 00 [UHCI]) Subsystem: Unknown device 0925:1234 Flags: bus master, medium devsel, latency 32, IRQ 19 I/O ports at a000 [size=32] Capabilities: [80] Power Management version 2 30: 00 00 00 00 80 00 00 00 00 00 00 00 19 04 00 00 So that is correct. I'll attach all the information from the MPS 1.4 reboot, in which 00:07.2 happily points at 05, while everything else thinks it's at 19..... 0: 00000000000f0000 - 0000000000100000 (reserved) BIOS-e820: 0000000000100000 - 000000001fff0000 (usable) BIOS-e820: 000000001fff0000 - 000000001fff3000 (ACPI NVS) BIOS-e820: 000000001fff3000 - 0000000020000000 (ACPI data) BIOS-e820: 00000000fec00000 - 00000000fec01000 (reserved) BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved) BIOS-e820: 00000000ffff0000 - 0000000100000000 (reserved) found SMP MP-table at 000f5770 hm, page 000f5000 reserved twice. hm, page 000f6000 reserved twice. hm, page 000f1000 reserved twice. hm, page 000f2000 reserved twice. On node 0 totalpages: 131056 zone(0): 4096 pages. zone(1): 126960 pages. zone(2): 0 pages. Intel MultiProcessor Specification v1.4 Virtual Wire compatibility mode. OEM ID: OEM00000 Product ID: PROD00000000 APIC at: 0xFEE00000 Processor #0 Pentium(tm) Pro APIC version 17 Processor #1 Pentium(tm) Pro APIC version 17 I/O APIC #2 Version 17 at 0xFEC00000. Processors: 2 Kernel command line: auto BOOT_IMAGE=SuSE-2.4.5ac5 ro root=2101 BOOT_FILE=/boot/prod/vmlinuz-245ac5 video=matrox:vesa:0x11E,fv:80,sgram Total of 2 processors activated (2808.21 BogoMIPS). ENABLING IO-APIC IRQs ...changing IO-APIC physical APIC ID to 2 ... ok. init IO_APIC IRQs IO-APIC (apicid-pin) 2-0, 2-5, 2-10, 2-11, 2-15, 2-20, 2-21, 2-22, 2-23 not connected. ..TIMER: vector=49 pin1=2 pin2=0 number of MP IRQ sources: 22. number of IO-APIC #2 registers: 24. testing the IO APIC....................... IO APIC #2...... .... register #00: 02000000 ....... : physical APIC id: 02 .... register #01: 00178011 ....... : max redirection entries: 0017 ....... : IO APIC version: 0011 WARNING: unexpected IO-APIC, please mail to linux-smp@vger.kernel.org .... register #02: 00000000 ....... : arbitration: 00 .... IRQ redirection table: NR Log Phy Mask Trig IRR Pol Stat Dest Deli Vect: 00 000 00 1 0 0 0 0 0 0 00 01 003 03 0 0 0 0 0 1 1 39 02 003 03 0 0 0 0 0 1 1 31 03 003 03 0 0 0 0 0 1 1 41 04 003 03 0 0 0 0 0 1 1 49 05 000 00 1 0 0 0 0 0 0 00 06 003 03 0 0 0 0 0 1 1 51 07 003 03 0 0 0 0 0 1 1 59 08 003 03 0 0 0 0 0 1 1 61 09 003 03 0 0 0 0 0 1 1 69 0a 000 00 1 0 0 0 0 0 0 00 0b 000 00 1 0 0 0 0 0 0 00 0c 003 03 0 0 0 0 0 1 1 71 0d 003 03 0 0 0 0 0 1 1 79 0e 003 03 0 0 0 0 0 1 1 81 0f 000 00 1 0 0 0 0 0 0 00 10 003 03 1 1 0 1 0 1 1 89 11 003 03 1 1 0 1 0 1 1 91 12 003 03 1 1 0 1 0 1 1 99 13 003 03 1 1 0 1 0 1 1 A1 14 000 00 1 0 0 0 0 0 0 00 15 000 00 1 0 0 0 0 0 0 00 16 000 00 1 0 0 0 0 0 0 00 17 000 00 1 0 0 0 0 0 0 00 IRQ to pin mappings: IRQ0 -> 0:2 IRQ1 -> 0:1 IRQ3 -> 0:3 IRQ4 -> 0:4 IRQ6 -> 0:6 IRQ7 -> 0:7 IRQ8 -> 0:8 IRQ9 -> 0:9 IRQ12 -> 0:12 IRQ13 -> 0:13 IRQ14 -> 0:14 IRQ16 -> 0:16 IRQ17 -> 0:17 IRQ18 -> 0:18 IRQ19 -> 0:19 .................................... done. Using local APIC timer interrupts. calibrating APIC timer ... ..... CPU clock speed is 703.2166 MHz. ..... host bus clock speed is 100.4593 MHz. PCI: Probing PCI hardware Unknown bridge resource 0: assuming transparent Unknown bridge resource 2: assuming transparent PCI: Using IRQ router VIA [1106/0686] at 00:07.0 PCI->APIC IRQ transform: (B0,I7,P3) -> 19 PCI->APIC IRQ transform: (B0,I7,P3) -> 19 PCI->APIC IRQ transform: (B0,I10,P0) -> 17 PCI->APIC IRQ transform: (B0,I11,P0) -> 17 PCI->APIC IRQ transform: (B0,I14,P0) -> 18 PCI->APIC IRQ transform: (B1,I0,P0) -> 16 PCI->APIC IRQ transform: (B2,I0,P0) -> 16 PCI->APIC IRQ transform: (B2,I1,P0) -> 17 PCI->APIC IRQ transform: (B2,I2,P0) -> 18 Linux NET4.0 for Linux 2.4 i2c-core.o: adapter MAVEN:fb0 on i2c-matroxfb registered as adapter 2. usb.c: registered new driver hub uhci.c: USB UHCI at I/O 0xa000, IRQ 19 usb.c: new USB bus registered, assigned bus number 1 hub.c: USB hub found hub.c: 2 ports detected uhci.c: USB UHCI at I/O 0xa400, IRQ 19 usb.c: new USB bus registered, assigned bus number 2 hub.c: USB hub found hub.c: 2 ports detected uhci.c: Linus Torvalds, Johannes Erdfelt, Randy Dunlap, Georg Acher, Deti Fliegl, Thomas Sailer, Roman Weissgaerber uhci.c: USB Universal Host Controller Interface driver Initializing USB Mass Storage driver... usb.c: registered new driver usb-storage USB Mass Storage support registered. NET4: Linux TCP/IP 1.0 for NET4.0 IP Protocols: ICMP, UDP, TCP, IGMP IP: routing cache hash table of 2048 buckets, 32Kbytes TCP: Hash tables configured (established 16384 bind 21845) NET4: Unix domain sockets 1.0/SMP for Linux NET4.0. VFS: Mounted root (ext2 filesystem) readonly. Freeing unused kernel memory: 248k freed hub.c: USB new device connect on bus1/1, assigned device number 2 Adding Swap: 1047776k swap-space (priority -1) reiserfs: checking transaction log (device 22:02) ... usb_control/bulk_msg: timeout usb.c: USB device not accepting new address=2 (error=-110) hub.c: USB new device connect on bus1/1, assigned device number 3 usb_control/bulk_msg: timeout usb.c: USB device not accepting new address=3 (error=-110) /proc/interrupts: CPU0 CPU1 0: 6043 3005 IO-APIC-edge timer 1: 38 3 IO-APIC-edge keyboard 2: 0 0 XT-PIC cascade 8: 0 2 IO-APIC-edge rtc 14: 179 224 IO-APIC-edge ide0 16: 32 33 IO-APIC-level sym53c8xx 17: 22 22 IO-APIC-level sym53c8xx, sym53c8xx, EMU10K1 18: 1657 1681 IO-APIC-level ide2, ide3, DE500-AA (eth0) 19: 0 0 IO-APIC-level usb-uhci, usb-uhci NMI: 0 0 LOC: 8966 8963 ERR: 0 MIS: 0 lspci: 00:00.0 Host bridge: VIA Technologies, Inc. VT82C693A/694x [Apollo PRO133x] (rev c4) Subsystem: ABIT Computer Corp.: Unknown device a204 Flags: bus master, medium devsel, latency 8 Memory at d0000000 (32-bit, prefetchable) [size=64M] Capabilities: [a0] AGP version 2.0 Capabilities: [c0] Power Management version 2 00:01.0 PCI bridge: VIA Technologies, Inc. VT82C598/694x [Apollo MVP3/Pro133x AGP] (prog-if 00 [Normal decode]) Flags: bus master, 66Mhz, medium devsel, latency 0 Bus: primary=00, secondary=01, subordinate=01, sec-latency=0 Memory behind bridge: d6000000-d8ffffff Prefetchable memory behind bridge: d4000000-d5ffffff Capabilities: [80] Power Management version 2 00:07.0 ISA bridge: VIA Technologies, Inc. VT82C686 [Apollo Super South] (rev 40) Subsystem: ABIT Computer Corp.: Unknown device 0000 Flags: bus master, stepping, medium devsel, latency 0 Capabilities: [c0] Power Management version 2 00:07.1 IDE interface: VIA Technologies, Inc. Bus Master IDE (rev 06) (prog-if 8a [Master SecP PriP]) Subsystem: VIA Technologies, Inc. Bus Master IDE Flags: bus master, medium devsel, latency 32 I/O ports at a800 [size=16] Capabilities: [c0] Power Management version 2 00:07.2 USB Controller: VIA Technologies, Inc. UHCI USB (rev 16) (prog-if 00 [UHCI]) Subsystem: Unknown device 0925:1234 Flags: bus master, medium devsel, latency 32, IRQ 19 I/O ports at a000 [size=32] Capabilities: [80] Power Management version 2 00:07.3 USB Controller: VIA Technologies, Inc. UHCI USB (rev 16) (prog-if 00 [UHCI]) Subsystem: Unknown device 0925:1234 Flags: bus master, medium devsel, latency 32, IRQ 19 I/O ports at a400 [size=32] Capabilities: [80] Power Management version 2 00:07.4 Bridge: VIA Technologies, Inc. VT82C686 [Apollo Super ACPI] (rev 40) Flags: medium devsel, IRQ 3 Capabilities: [68] Power Management version 2 00:09.0 PCI bridge: Digital Equipment Corporation DECchip 21152 (rev 02) (prog-if 00 [Normal decode]) Flags: bus master, medium devsel, latency 32 Bus: primary=00, secondary=02, subordinate=02, sec-latency=32 I/O behind bridge: 00009000-00009fff Memory behind bridge: d9000000-daffffff 00:0a.0 SCSI storage controller: Symbios Logic Inc. (formerly NCR) 53c860 (rev 13) Subsystem: Symbios Logic Inc. (formerly NCR): Unknown device 1000 Flags: bus master, medium devsel, latency 32, IRQ 17 I/O ports at ac00 [size=256] Memory at dc000000 (32-bit, non-prefetchable) [size=256] Capabilities: [40] Power Management version 1 00:0b.0 Multimedia audio controller: Creative Labs SB Live! EMU10000 (rev 07) Subsystem: Creative Labs: Unknown device 8061 Flags: bus master, medium devsel, latency 32, IRQ 17 I/O ports at b000 [size=32] Capabilities: [dc] Power Management version 1 00:0b.1 Input device controller: Creative Labs SB Live! (rev 07) Subsystem: Creative Labs Gameport Joystick Flags: bus master, medium devsel, latency 32 I/O ports at b400 [size=8] Capabilities: [dc] Power Management version 1 00:0e.0 Unknown mass storage controller: Triones Technologies, Inc. HPT366 (rev 03) Subsystem: Triones Technologies, Inc.: Unknown device 0001 Flags: bus master, 66Mhz, medium devsel, latency 120, IRQ 18 I/O ports at b800 [size=8] I/O ports at bc00 [size=4] I/O ports at c000 [size=8] I/O ports at c400 [size=4] I/O ports at c800 [size=256] Expansion ROM at <unassigned> [disabled] [size=128K] Capabilities: [60] Power Management version 2 01:00.0 VGA compatible controller: Matrox Graphics, Inc. MGA G400 AGP (rev 03) (prog-if 00 [VGA]) Subsystem: Matrox Graphics, Inc. Millennium G400 32Mb SGRAM Flags: bus master, medium devsel, latency 32, IRQ 16 Memory at d4000000 (32-bit, prefetchable) [size=32M] Memory at d6000000 (32-bit, non-prefetchable) [size=16K] Memory at d7000000 (32-bit, non-prefetchable) [size=8M] Expansion ROM at <unassigned> [disabled] [size=64K] Capabilities: [dc] Power Management version 2 Capabilities: [f0] AGP version 2.0 02:00.0 SCSI storage controller: Symbios Logic Inc. (formerly NCR) 53c875 (rev 04) Flags: bus master, medium devsel, latency 72, IRQ 16 I/O ports at 9000 [size=256] Memory at da001000 (32-bit, non-prefetchable) [size=256] Memory at da000000 (32-bit, non-prefetchable) [size=4K] Expansion ROM at <unassigned> [disabled] [size=64K] 02:01.0 SCSI storage controller: Symbios Logic Inc. (formerly NCR) 53c875 (rev 04) Flags: bus master, medium devsel, latency 72, IRQ 17 I/O ports at 9400 [size=256] Memory at da002000 (32-bit, non-prefetchable) [size=256] Memory at da003000 (32-bit, non-prefetchable) [size=4K] Expansion ROM at <unassigned> [disabled] [size=64K] 02:02.0 Ethernet controller: Digital Equipment Corporation DECchip 21140 [FasterNet] (rev 22) Subsystem: Digital Equipment Corporation: Unknown device 500a Flags: bus master, medium devsel, latency 96, IRQ 18 I/O ports at 9800 [size=128] Memory at da004000 (32-bit, non-prefetchable) [size=128] Expansion ROM at <unassigned> [disabled] [size=256K] lspci -vvvxx: 00:00.0 Host bridge: VIA Technologies, Inc. VT82C693A/694x [Apollo PRO133x] (rev c4) Subsystem: ABIT Computer Corp.: Unknown device a204 Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR- Latency: 8 Region 0: Memory at d0000000 (32-bit, prefetchable) [size=64M] Capabilities: [a0] AGP version 2.0 Status: RQ=31 SBA+ 64bit- FW- Rate=x1,x2 Command: RQ=0 SBA- AGP- 64bit- FW- Rate=<none> Capabilities: [c0] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME- 00: 06 11 91 06 06 00 10 22 c4 00 00 06 00 08 00 00 10: 08 00 00 d0 00 00 00 00 00 00 00 00 00 00 00 00 20: 00 00 00 00 00 00 00 00 00 00 00 00 7b 14 04 a2 30: 00 00 00 00 a0 00 00 00 00 00 00 00 00 00 00 00 00:01.0 PCI bridge: VIA Technologies, Inc. VT82C598/694x [Apollo MVP3/Pro133x AGP] (prog-if 00 [Normal decode]) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR- Latency: 0 Bus: primary=00, secondary=01, subordinate=01, sec-latency=0 I/O behind bridge: 0000f000-00000fff Memory behind bridge: d6000000-d8ffffff Prefetchable memory behind bridge: d4000000-d5ffffff BridgeCtl: Parity- SERR- NoISA+ VGA+ MAbort- >Reset- FastB2B- Capabilities: [80] Power Management version 2 Flags: PMEClk- DSI- D1+ D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME- 00: 06 11 98 85 07 00 30 22 00 00 04 06 00 00 01 00 10: 00 00 00 00 00 00 00 00 00 01 01 00 f0 00 00 00 20: 00 d6 f0 d8 00 d4 f0 d5 00 00 00 00 00 00 00 00 30: 00 00 00 00 80 00 00 00 00 00 00 00 00 00 0c 00 00:07.0 ISA bridge: VIA Technologies, Inc. VT82C686 [Apollo Super South] (rev 40) Subsystem: ABIT Computer Corp.: Unknown device 0000 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping+ SERR- FastB2B- Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 0 Capabilities: [c0] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME- 00: 06 11 86 06 87 00 10 02 40 00 01 06 00 00 80 00 10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 20: 00 00 00 00 00 00 00 00 00 00 00 00 7b 14 00 00 30: 00 00 00 00 c0 00 00 00 00 00 00 00 00 00 00 00 00:07.1 IDE interface: VIA Technologies, Inc. Bus Master IDE (rev 06) (prog-if 8a [Master SecP PriP]) Subsystem: VIA Technologies, Inc. Bus Master IDE Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 32 Region 4: I/O ports at a800 [size=16] Capabilities: [c0] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME- 00: 06 11 71 05 07 00 90 02 06 8a 01 01 00 20 00 00 10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 20: 01 a8 00 00 00 00 00 00 00 00 00 00 06 11 71 05 30: 00 00 00 00 c0 00 00 00 00 00 00 00 ff 00 00 00 00:07.2 USB Controller: VIA Technologies, Inc. UHCI USB (rev 16) (prog-if 00 [UHCI]) Subsystem: Unknown device 0925:1234 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 32, cache line size 08 Interrupt: pin D routed to IRQ 19 Region 4: I/O ports at a000 [size=32] Capabilities: [80] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME- 00: 06 11 38 30 07 00 10 02 16 00 03 0c 08 20 00 00 10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 20: 01 a0 00 00 00 00 00 00 00 00 00 00 25 09 34 12 30: 00 00 00 00 80 00 00 00 00 00 00 00 05 04 00 00 00:07.3 USB Controller: VIA Technologies, Inc. UHCI USB (rev 16) (prog-if 00 [UHCI]) Subsystem: Unknown device 0925:1234 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 32, cache line size 08 Interrupt: pin D routed to IRQ 19 Region 4: I/O ports at a400 [size=32] Capabilities: [80] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME- 00: 06 11 38 30 07 00 10 02 16 00 03 0c 08 20 00 00 10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 20: 01 a4 00 00 00 00 00 00 00 00 00 00 25 09 34 12 30: 00 00 00 00 80 00 00 00 00 00 00 00 05 04 00 00 00:07.4 Bridge: VIA Technologies, Inc. VT82C686 [Apollo Super ACPI] (rev 40) Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Interrupt: pin ? routed to IRQ 3 Capabilities: [68] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME- 00: 06 11 57 30 00 00 90 02 40 00 80 06 00 00 00 00 10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 20: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 30: 00 00 00 00 68 00 00 00 00 00 00 00 00 00 00 00 00:09.0 PCI bridge: Digital Equipment Corporation DECchip 21152 (rev 02) (prog-if 00 [Normal decode]) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 32, cache line size 08 Bus: primary=00, secondary=02, subordinate=02, sec-latency=32 I/O behind bridge: 00009000-00009fff Memory behind bridge: d9000000-daffffff Prefetchable memory behind bridge: 00000000fff00000-0000000000000000 BridgeCtl: Parity- SERR+ NoISA+ VGA- MAbort- >Reset- FastB2B- 00: 11 10 24 00 07 01 80 02 02 00 04 06 08 20 01 00 10: 00 00 00 00 00 00 00 00 00 02 02 20 91 91 80 22 20: 00 d9 f0 da f1 ff 01 00 00 00 00 00 00 00 00 00 30: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 06 00 00:0a.0 SCSI storage controller: Symbios Logic Inc. (formerly NCR) 53c860 (rev 13) Subsystem: Symbios Logic Inc. (formerly NCR): Unknown device 1000 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR- FastB2B- Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 32 (2000ns min, 16000ns max), cache line size 08 Interrupt: pin A routed to IRQ 17 Region 0: I/O ports at ac00 [size=256] Region 1: Memory at dc000000 (32-bit, non-prefetchable) [size=256] Capabilities: [40] Power Management version 1 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME- 00: 00 10 06 00 47 00 10 02 13 00 00 01 08 20 00 00 10: 01 ac 00 00 00 00 00 dc 00 00 00 00 00 00 00 00 20: 00 00 00 00 00 00 00 00 00 00 00 00 00 10 00 10 30: 00 00 00 00 40 00 00 00 00 00 00 00 0b 01 08 40 00:0b.0 Multimedia audio controller: Creative Labs SB Live! EMU10000 (rev 07) Subsystem: Creative Labs: Unknown device 8061 Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 32 (500ns min, 5000ns max) Interrupt: pin A routed to IRQ 17 Region 0: I/O ports at b000 [size=32] Capabilities: [dc] Power Management version 1 Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME- 00: 02 11 02 00 05 00 90 02 07 00 01 04 00 20 80 00 10: 01 b0 00 00 00 00 00 00 00 00 00 00 00 00 00 00 20: 00 00 00 00 00 00 00 00 00 00 00 00 02 11 61 80 30: 00 00 00 00 dc 00 00 00 00 00 00 00 0b 01 02 14 00:0b.1 Input device controller: Creative Labs SB Live! (rev 07) Subsystem: Creative Labs Gameport Joystick Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 32 Region 0: I/O ports at b400 [size=8] Capabilities: [dc] Power Management version 1 Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME- 00: 02 11 02 70 05 00 90 02 07 00 80 09 00 20 80 00 10: 01 b4 00 00 00 00 00 00 00 00 00 00 00 00 00 00 20: 00 00 00 00 00 00 00 00 00 00 00 00 02 11 20 00 30: 00 00 00 00 dc 00 00 00 00 00 00 00 00 00 00 00 00:0e.0 Unknown mass storage controller: Triones Technologies, Inc. HPT366 (rev 03) Subsystem: Triones Technologies, Inc.: Unknown device 0001 Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 120 (2000ns min, 2000ns max), cache line size 08 Interrupt: pin A routed to IRQ 18 Region 0: I/O ports at b800 [size=8] Region 1: I/O ports at bc00 [size=4] Region 2: I/O ports at c000 [size=8] Region 3: I/O ports at c400 [size=4] Region 4: I/O ports at c800 [size=256] Expansion ROM at <unassigned> [disabled] [size=128K] Capabilities: [60] Power Management version 2 Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME- 00: 03 11 04 00 05 00 30 02 03 00 80 01 08 78 00 00 10: 01 b8 00 00 01 bc 00 00 01 c0 00 00 01 c4 00 00 20: 01 c8 00 00 00 00 00 00 00 00 00 00 03 11 01 00 30: 00 00 00 00 60 00 00 00 00 00 00 00 0a 01 08 08 01:00.0 VGA compatible controller: Matrox Graphics, Inc. MGA G400 AGP (rev 03) (prog-if 00 [VGA]) Subsystem: Matrox Graphics, Inc. Millennium G400 32Mb SGRAM Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 32 (4000ns min, 8000ns max), cache line size 08 Interrupt: pin A routed to IRQ 16 Region 0: Memory at d4000000 (32-bit, prefetchable) [size=32M] Region 1: Memory at d6000000 (32-bit, non-prefetchable) [size=16K] Region 2: Memory at d7000000 (32-bit, non-prefetchable) [size=8M] Expansion ROM at <unassigned> [disabled] [size=64K] Capabilities: [dc] Power Management version 2 Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME- Capabilities: [f0] AGP version 2.0 Status: RQ=31 SBA+ 64bit- FW- Rate=x1,x2 Command: RQ=31 SBA+ AGP+ 64bit- FW- Rate=x1 00: 2b 10 25 05 07 00 90 02 03 00 00 03 08 20 00 00 10: 08 00 00 d4 00 00 00 d6 00 00 00 d7 00 00 00 00 20: 00 00 00 00 00 00 00 00 00 00 00 00 2b 10 f8 19 30: 00 00 00 00 dc 00 00 00 00 00 00 00 0f 01 10 20 02:00.0 SCSI storage controller: Symbios Logic Inc. (formerly NCR) 53c875 (rev 04) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR- FastB2B- Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 72 (4250ns min, 16000ns max), cache line size 08 Interrupt: pin A routed to IRQ 16 Region 0: I/O ports at 9000 [size=256] Region 1: Memory at da001000 (32-bit, non-prefetchable) [size=256] Region 2: Memory at da000000 (32-bit, non-prefetchable) [size=4K] Expansion ROM at <unassigned> [disabled] [size=64K] 00: 00 10 0f 00 47 00 00 02 04 00 00 01 08 48 00 00 10: 01 90 00 00 00 10 00 da 00 00 00 da 00 00 00 00 20: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 30: 00 00 00 00 00 00 00 00 00 00 00 00 0f 01 11 40 02:01.0 SCSI storage controller: Symbios Logic Inc. (formerly NCR) 53c875 (rev 04) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR- FastB2B- Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 72 (4250ns min, 16000ns max), cache line size 08 Interrupt: pin A routed to IRQ 17 Region 0: I/O ports at 9400 [size=256] Region 1: Memory at da002000 (32-bit, non-prefetchable) [size=256] Region 2: Memory at da003000 (32-bit, non-prefetchable) [size=4K] Expansion ROM at <unassigned> [disabled] [size=64K] 00: 00 10 0f 00 47 00 00 02 04 00 00 01 08 48 00 00 10: 01 94 00 00 00 20 00 da 00 30 00 da 00 00 00 00 20: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 30: 00 00 00 00 00 00 00 00 00 00 00 00 0b 01 11 40 02:02.0 Ethernet controller: Digital Equipment Corporation DECchip 21140 [FasterNet] (rev 22) Subsystem: Digital Equipment Corporation: Unknown device 500a Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 96 (5000ns min, 10000ns max), cache line size 08 Interrupt: pin A routed to IRQ 18 Region 0: I/O ports at 9800 [size=128] Region 1: Memory at da004000 (32-bit, non-prefetchable) [size=128] Expansion ROM at <unassigned> [disabled] [size=256K] 00: 11 10 09 00 07 00 80 02 22 00 00 02 08 60 00 00 10: 01 98 00 00 00 40 00 da 00 00 00 00 00 00 00 00 20: 00 00 00 00 00 00 00 00 00 00 00 00 11 10 0a 50 30: 00 00 00 00 00 00 00 00 00 00 00 00 0a 01 14 28 Good luck, Jurriaan -- BOFH excuse #222: I'm not sure. Try calling the Internet's head office -- it's in the book. GNU/Linux 2.4.5-ac5 SMP/ReiserFS 2x1402 bogomips load av: 0.03 0.10 0.06 ^ permalink raw reply [flat|nested] 11+ messages in thread
* Re: interrupt problem with MPS 1.4 / not with MPS 1.1 ? 2001-06-01 5:14 ` thunder7 @ 2001-06-01 5:20 ` Jeff Garzik 2001-06-01 5:39 ` thunder7 2001-06-01 17:28 ` Manfred Spraul 1 sibling, 1 reply; 11+ messages in thread From: Jeff Garzik @ 2001-06-01 5:20 UTC (permalink / raw) To: thunder7; +Cc: Manfred Spraul, linux-kernel Looking at the diff of "lspci -vvvxxx" between MPS1.1 and MPS1.4 (on the same system) may be quite useful... maybe I missed the earlier "lspci -vvvxxx", but I only see one here... -- Jeff Garzik | Disbelief, that's why you fail. Building 1024 | MandrakeSoft | ^ permalink raw reply [flat|nested] 11+ messages in thread
* Re: interrupt problem with MPS 1.4 / not with MPS 1.1 ? 2001-06-01 5:20 ` Jeff Garzik @ 2001-06-01 5:39 ` thunder7 0 siblings, 0 replies; 11+ messages in thread From: thunder7 @ 2001-06-01 5:39 UTC (permalink / raw) To: Jeff Garzik; +Cc: linux-kernel On Fri, Jun 01, 2001 at 01:20:23AM -0400, Jeff Garzik wrote: > Looking at the diff of "lspci -vvvxxx" between MPS1.1 and MPS1.4 (on the > same system) may be quite useful... maybe I missed the earlier "lspci > -vvvxxx", but I only see one here... Yep, I didn't want to keep sending long messages. Here goes: diff pci_11 pci_14: -- 4c4 < Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR+ --- > Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR- I see, this isn't going to work. I'll insert the complete dump from mps 1.1 here, followed by the same from 1.4: 00:00.0 Host bridge: VIA Technologies, Inc. VT82C693A/694x [Apollo PRO133x] (rev c4) Subsystem: ABIT Computer Corp.: Unknown device a204 Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR+ Latency: 8 Region 0: Memory at d0000000 (32-bit, prefetchable) [size=64M] Capabilities: [a0] AGP version 2.0 Status: RQ=31 SBA+ 64bit- FW- Rate=x1,x2 Command: RQ=0 SBA- AGP- 64bit- FW- Rate=<none> Capabilities: [c0] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME- 00: 06 11 91 06 06 00 10 a2 c4 00 00 06 00 08 00 00 10: 08 00 00 d0 00 00 00 00 00 00 00 00 00 00 00 00 20: 00 00 00 00 00 00 00 00 00 00 00 00 7b 14 04 a2 30: 00 00 00 00 a0 00 00 00 00 00 00 00 00 00 00 00 00:01.0 PCI bridge: VIA Technologies, Inc. VT82C598/694x [Apollo MVP3/Pro133x AGP] (prog-if 00 [Normal decode]) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR- Latency: 0 Bus: primary=00, secondary=01, subordinate=01, sec-latency=0 I/O behind bridge: 0000f000-00000fff Memory behind bridge: d6000000-d8ffffff Prefetchable memory behind bridge: d4000000-d5ffffff BridgeCtl: Parity- SERR- NoISA+ VGA+ MAbort- >Reset- FastB2B- Capabilities: [80] Power Management version 2 Flags: PMEClk- DSI- D1+ D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME- 00: 06 11 98 85 07 00 30 22 00 00 04 06 00 00 01 00 10: 00 00 00 00 00 00 00 00 00 01 01 00 f0 00 00 00 20: 00 d6 f0 d8 00 d4 f0 d5 00 00 00 00 00 00 00 00 30: 00 00 00 00 80 00 00 00 00 00 00 00 00 00 0c 00 00:07.0 ISA bridge: VIA Technologies, Inc. VT82C686 [Apollo Super South] (rev 40) Subsystem: ABIT Computer Corp.: Unknown device 0000 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping+ SERR- FastB2B- Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 0 Capabilities: [c0] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME- 00: 06 11 86 06 87 00 10 02 40 00 01 06 00 00 80 00 10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 20: 00 00 00 00 00 00 00 00 00 00 00 00 7b 14 00 00 30: 00 00 00 00 c0 00 00 00 00 00 00 00 00 00 00 00 00:07.1 IDE interface: VIA Technologies, Inc. Bus Master IDE (rev 06) (prog-if 8a [Master SecP PriP]) Subsystem: VIA Technologies, Inc. Bus Master IDE Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 32 Region 4: I/O ports at a800 [size=16] Capabilities: [c0] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME- 00: 06 11 71 05 07 00 90 02 06 8a 01 01 00 20 00 00 10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 20: 01 a8 00 00 00 00 00 00 00 00 00 00 06 11 71 05 30: 00 00 00 00 c0 00 00 00 00 00 00 00 ff 00 00 00 00:07.2 USB Controller: VIA Technologies, Inc. UHCI USB (rev 16) (prog-if 00 [UHCI]) Subsystem: Unknown device 0925:1234 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 32, cache line size 08 Interrupt: pin D routed to IRQ 5 Region 4: I/O ports at a000 [size=32] Capabilities: [80] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME- 00: 06 11 38 30 07 00 10 02 16 00 03 0c 08 20 00 00 10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 20: 01 a0 00 00 00 00 00 00 00 00 00 00 25 09 34 12 30: 00 00 00 00 80 00 00 00 00 00 00 00 05 04 00 00 00:07.3 USB Controller: VIA Technologies, Inc. UHCI USB (rev 16) (prog-if 00 [UHCI]) Subsystem: Unknown device 0925:1234 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 32, cache line size 08 Interrupt: pin D routed to IRQ 5 Region 4: I/O ports at a400 [size=32] Capabilities: [80] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME- 00: 06 11 38 30 07 00 10 02 16 00 03 0c 08 20 00 00 10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 20: 01 a4 00 00 00 00 00 00 00 00 00 00 25 09 34 12 30: 00 00 00 00 80 00 00 00 00 00 00 00 05 04 00 00 00:07.4 Bridge: VIA Technologies, Inc. VT82C686 [Apollo Super ACPI] (rev 40) Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Interrupt: pin ? routed to IRQ 3 Capabilities: [68] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME- 00: 06 11 57 30 00 00 90 02 40 00 80 06 00 00 00 00 10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 20: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 30: 00 00 00 00 68 00 00 00 00 00 00 00 00 00 00 00 00:09.0 PCI bridge: Digital Equipment Corporation DECchip 21152 (rev 02) (prog-if 00 [Normal decode]) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 32, cache line size 08 Bus: primary=00, secondary=02, subordinate=02, sec-latency=32 I/O behind bridge: 00009000-00009fff Memory behind bridge: d9000000-daffffff Prefetchable memory behind bridge: 00000000fff00000-0000000000000000 BridgeCtl: Parity- SERR+ NoISA+ VGA- MAbort- >Reset- FastB2B- 00: 11 10 24 00 07 01 80 02 02 00 04 06 08 20 01 00 10: 00 00 00 00 00 00 00 00 00 02 02 20 91 91 80 22 20: 00 d9 f0 da f1 ff 01 00 00 00 00 00 00 00 00 00 30: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 06 00 00:0a.0 SCSI storage controller: Symbios Logic Inc. (formerly NCR) 53c860 (rev 13) Subsystem: Symbios Logic Inc. (formerly NCR): Unknown device 1000 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR- FastB2B- Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 32 (2000ns min, 16000ns max), cache line size 08 Interrupt: pin A routed to IRQ 11 Region 0: I/O ports at ac00 [size=256] Region 1: Memory at dc000000 (32-bit, non-prefetchable) [size=256] Capabilities: [40] Power Management version 1 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME- 00: 00 10 06 00 47 00 10 02 13 00 00 01 08 20 00 00 10: 01 ac 00 00 00 00 00 dc 00 00 00 00 00 00 00 00 20: 00 00 00 00 00 00 00 00 00 00 00 00 00 10 00 10 30: 00 00 00 00 40 00 00 00 00 00 00 00 0b 01 08 40 00:0b.0 Multimedia audio controller: Creative Labs SB Live! EMU10000 (rev 07) Subsystem: Creative Labs: Unknown device 8061 Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 32 (500ns min, 5000ns max) Interrupt: pin A routed to IRQ 11 Region 0: I/O ports at b000 [size=32] Capabilities: [dc] Power Management version 1 Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME- 00: 02 11 02 00 05 00 90 02 07 00 01 04 00 20 80 00 10: 01 b0 00 00 00 00 00 00 00 00 00 00 00 00 00 00 20: 00 00 00 00 00 00 00 00 00 00 00 00 02 11 61 80 30: 00 00 00 00 dc 00 00 00 00 00 00 00 0b 01 02 14 00:0b.1 Input device controller: Creative Labs SB Live! (rev 07) Subsystem: Creative Labs Gameport Joystick Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 32 Region 0: I/O ports at b400 [size=8] Capabilities: [dc] Power Management version 1 Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME- 00: 02 11 02 70 05 00 90 02 07 00 80 09 00 20 80 00 10: 01 b4 00 00 00 00 00 00 00 00 00 00 00 00 00 00 20: 00 00 00 00 00 00 00 00 00 00 00 00 02 11 20 00 30: 00 00 00 00 dc 00 00 00 00 00 00 00 00 00 00 00 00:0e.0 Unknown mass storage controller: Triones Technologies, Inc. HPT366 (rev 03) Subsystem: Triones Technologies, Inc.: Unknown device 0001 Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 120 (2000ns min, 2000ns max), cache line size 08 Interrupt: pin A routed to IRQ 10 Region 0: I/O ports at b800 [size=8] Region 1: I/O ports at bc00 [size=4] Region 2: I/O ports at c000 [size=8] Region 3: I/O ports at c400 [size=4] Region 4: I/O ports at c800 [size=256] Expansion ROM at <unassigned> [disabled] [size=128K] Capabilities: [60] Power Management version 2 Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME- 00: 03 11 04 00 05 00 30 02 03 00 80 01 08 78 00 00 10: 01 b8 00 00 01 bc 00 00 01 c0 00 00 01 c4 00 00 20: 01 c8 00 00 00 00 00 00 00 00 00 00 03 11 01 00 30: 00 00 00 00 60 00 00 00 00 00 00 00 0a 01 08 08 01:00.0 VGA compatible controller: Matrox Graphics, Inc. MGA G400 AGP (rev 03) (prog-if 00 [VGA]) Subsystem: Matrox Graphics, Inc. Millennium G400 32Mb SGRAM Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 32 (4000ns min, 8000ns max), cache line size 08 Interrupt: pin A routed to IRQ 15 Region 0: Memory at d4000000 (32-bit, prefetchable) [size=32M] Region 1: Memory at d6000000 (32-bit, non-prefetchable) [size=16K] Region 2: Memory at d7000000 (32-bit, non-prefetchable) [size=8M] Expansion ROM at <unassigned> [disabled] [size=64K] Capabilities: [dc] Power Management version 2 Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME- Capabilities: [f0] AGP version 2.0 Status: RQ=31 SBA+ 64bit- FW- Rate=x1,x2 Command: RQ=31 SBA+ AGP+ 64bit- FW- Rate=x1 00: 2b 10 25 05 07 00 90 02 03 00 00 03 08 20 00 00 10: 08 00 00 d4 00 00 00 d6 00 00 00 d7 00 00 00 00 20: 00 00 00 00 00 00 00 00 00 00 00 00 2b 10 f8 19 30: 00 00 00 00 dc 00 00 00 00 00 00 00 0f 01 10 20 02:00.0 SCSI storage controller: Symbios Logic Inc. (formerly NCR) 53c875 (rev 04) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR- FastB2B- Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 72 (4250ns min, 16000ns max), cache line size 08 Interrupt: pin A routed to IRQ 15 Region 0: I/O ports at 9000 [size=256] Region 1: Memory at da001000 (32-bit, non-prefetchable) [size=256] Region 2: Memory at da000000 (32-bit, non-prefetchable) [size=4K] Expansion ROM at <unassigned> [disabled] [size=64K] 00: 00 10 0f 00 47 00 00 02 04 00 00 01 08 48 00 00 10: 01 90 00 00 00 10 00 da 00 00 00 da 00 00 00 00 20: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 30: 00 00 00 00 00 00 00 00 00 00 00 00 0f 01 11 40 02:01.0 SCSI storage controller: Symbios Logic Inc. (formerly NCR) 53c875 (rev 04) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR- FastB2B- Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 72 (4250ns min, 16000ns max), cache line size 08 Interrupt: pin A routed to IRQ 11 Region 0: I/O ports at 9400 [size=256] Region 1: Memory at da002000 (32-bit, non-prefetchable) [size=256] Region 2: Memory at da003000 (32-bit, non-prefetchable) [size=4K] Expansion ROM at <unassigned> [disabled] [size=64K] 00: 00 10 0f 00 47 00 00 02 04 00 00 01 08 48 00 00 10: 01 94 00 00 00 20 00 da 00 30 00 da 00 00 00 00 20: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 30: 00 00 00 00 00 00 00 00 00 00 00 00 0b 01 11 40 02:02.0 Ethernet controller: Digital Equipment Corporation DECchip 21140 [FasterNet] (rev 22) Subsystem: Digital Equipment Corporation: Unknown device 500a Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 96 (5000ns min, 10000ns max), cache line size 08 Interrupt: pin A routed to IRQ 10 Region 0: I/O ports at 9800 [size=128] Region 1: Memory at da004000 (32-bit, non-prefetchable) [size=128] Expansion ROM at <unassigned> [disabled] [size=256K] 00: 11 10 09 00 07 00 80 02 22 00 00 02 08 60 00 00 10: 01 98 00 00 00 40 00 da 00 00 00 00 00 00 00 00 20: 00 00 00 00 00 00 00 00 00 00 00 00 11 10 0a 50 30: 00 00 00 00 00 00 00 00 00 00 00 00 0a 01 14 28 from 1.4: 00:00.0 Host bridge: VIA Technologies, Inc. VT82C693A/694x [Apollo PRO133x] (rev c4) Subsystem: ABIT Computer Corp.: Unknown device a204 Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR- Latency: 8 Region 0: Memory at d0000000 (32-bit, prefetchable) [size=64M] Capabilities: [a0] AGP version 2.0 Status: RQ=31 SBA+ 64bit- FW- Rate=x1,x2 Command: RQ=0 SBA- AGP- 64bit- FW- Rate=<none> Capabilities: [c0] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME- 00: 06 11 91 06 06 00 10 22 c4 00 00 06 00 08 00 00 10: 08 00 00 d0 00 00 00 00 00 00 00 00 00 00 00 00 20: 00 00 00 00 00 00 00 00 00 00 00 00 7b 14 04 a2 30: 00 00 00 00 a0 00 00 00 00 00 00 00 00 00 00 00 00:01.0 PCI bridge: VIA Technologies, Inc. VT82C598/694x [Apollo MVP3/Pro133x AGP] (prog-if 00 [Normal decode]) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR- Latency: 0 Bus: primary=00, secondary=01, subordinate=01, sec-latency=0 I/O behind bridge: 0000f000-00000fff Memory behind bridge: d6000000-d8ffffff Prefetchable memory behind bridge: d4000000-d5ffffff BridgeCtl: Parity- SERR- NoISA+ VGA+ MAbort- >Reset- FastB2B- Capabilities: [80] Power Management version 2 Flags: PMEClk- DSI- D1+ D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME- 00: 06 11 98 85 07 00 30 22 00 00 04 06 00 00 01 00 10: 00 00 00 00 00 00 00 00 00 01 01 00 f0 00 00 00 20: 00 d6 f0 d8 00 d4 f0 d5 00 00 00 00 00 00 00 00 30: 00 00 00 00 80 00 00 00 00 00 00 00 00 00 0c 00 00:07.0 ISA bridge: VIA Technologies, Inc. VT82C686 [Apollo Super South] (rev 40) Subsystem: ABIT Computer Corp.: Unknown device 0000 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping+ SERR- FastB2B- Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 0 Capabilities: [c0] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME- 00: 06 11 86 06 87 00 10 02 40 00 01 06 00 00 80 00 10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 20: 00 00 00 00 00 00 00 00 00 00 00 00 7b 14 00 00 30: 00 00 00 00 c0 00 00 00 00 00 00 00 00 00 00 00 00:07.1 IDE interface: VIA Technologies, Inc. Bus Master IDE (rev 06) (prog-if 8a [Master SecP PriP]) Subsystem: VIA Technologies, Inc. Bus Master IDE Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 32 Region 4: I/O ports at a800 [size=16] Capabilities: [c0] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME- 00: 06 11 71 05 07 00 90 02 06 8a 01 01 00 20 00 00 10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 20: 01 a8 00 00 00 00 00 00 00 00 00 00 06 11 71 05 30: 00 00 00 00 c0 00 00 00 00 00 00 00 ff 00 00 00 00:07.2 USB Controller: VIA Technologies, Inc. UHCI USB (rev 16) (prog-if 00 [UHCI]) Subsystem: Unknown device 0925:1234 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 32, cache line size 08 Interrupt: pin D routed to IRQ 19 Region 4: I/O ports at a000 [size=32] Capabilities: [80] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME- 00: 06 11 38 30 07 00 10 02 16 00 03 0c 08 20 00 00 10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 20: 01 a0 00 00 00 00 00 00 00 00 00 00 25 09 34 12 30: 00 00 00 00 80 00 00 00 00 00 00 00 05 04 00 00 00:07.3 USB Controller: VIA Technologies, Inc. UHCI USB (rev 16) (prog-if 00 [UHCI]) Subsystem: Unknown device 0925:1234 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 32, cache line size 08 Interrupt: pin D routed to IRQ 19 Region 4: I/O ports at a400 [size=32] Capabilities: [80] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME- 00: 06 11 38 30 07 00 10 02 16 00 03 0c 08 20 00 00 10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 20: 01 a4 00 00 00 00 00 00 00 00 00 00 25 09 34 12 30: 00 00 00 00 80 00 00 00 00 00 00 00 05 04 00 00 00:07.4 Bridge: VIA Technologies, Inc. VT82C686 [Apollo Super ACPI] (rev 40) Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Interrupt: pin ? routed to IRQ 3 Capabilities: [68] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME- 00: 06 11 57 30 00 00 90 02 40 00 80 06 00 00 00 00 10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 20: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 30: 00 00 00 00 68 00 00 00 00 00 00 00 00 00 00 00 00:09.0 PCI bridge: Digital Equipment Corporation DECchip 21152 (rev 02) (prog-if 00 [Normal decode]) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 32, cache line size 08 Bus: primary=00, secondary=02, subordinate=02, sec-latency=32 I/O behind bridge: 00009000-00009fff Memory behind bridge: d9000000-daffffff Prefetchable memory behind bridge: 00000000fff00000-0000000000000000 BridgeCtl: Parity- SERR+ NoISA+ VGA- MAbort- >Reset- FastB2B- 00: 11 10 24 00 07 01 80 02 02 00 04 06 08 20 01 00 10: 00 00 00 00 00 00 00 00 00 02 02 20 91 91 80 22 20: 00 d9 f0 da f1 ff 01 00 00 00 00 00 00 00 00 00 30: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 06 00 00:0a.0 SCSI storage controller: Symbios Logic Inc. (formerly NCR) 53c860 (rev 13) Subsystem: Symbios Logic Inc. (formerly NCR): Unknown device 1000 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR- FastB2B- Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 32 (2000ns min, 16000ns max), cache line size 08 Interrupt: pin A routed to IRQ 17 Region 0: I/O ports at ac00 [size=256] Region 1: Memory at dc000000 (32-bit, non-prefetchable) [size=256] Capabilities: [40] Power Management version 1 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME- 00: 00 10 06 00 47 00 10 02 13 00 00 01 08 20 00 00 10: 01 ac 00 00 00 00 00 dc 00 00 00 00 00 00 00 00 20: 00 00 00 00 00 00 00 00 00 00 00 00 00 10 00 10 30: 00 00 00 00 40 00 00 00 00 00 00 00 0b 01 08 40 00:0b.0 Multimedia audio controller: Creative Labs SB Live! EMU10000 (rev 07) Subsystem: Creative Labs: Unknown device 8061 Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 32 (500ns min, 5000ns max) Interrupt: pin A routed to IRQ 17 Region 0: I/O ports at b000 [size=32] Capabilities: [dc] Power Management version 1 Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME- 00: 02 11 02 00 05 00 90 02 07 00 01 04 00 20 80 00 10: 01 b0 00 00 00 00 00 00 00 00 00 00 00 00 00 00 20: 00 00 00 00 00 00 00 00 00 00 00 00 02 11 61 80 30: 00 00 00 00 dc 00 00 00 00 00 00 00 0b 01 02 14 00:0b.1 Input device controller: Creative Labs SB Live! (rev 07) Subsystem: Creative Labs Gameport Joystick Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 32 Region 0: I/O ports at b400 [size=8] Capabilities: [dc] Power Management version 1 Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME- 00: 02 11 02 70 05 00 90 02 07 00 80 09 00 20 80 00 10: 01 b4 00 00 00 00 00 00 00 00 00 00 00 00 00 00 20: 00 00 00 00 00 00 00 00 00 00 00 00 02 11 20 00 30: 00 00 00 00 dc 00 00 00 00 00 00 00 00 00 00 00 00:0e.0 Unknown mass storage controller: Triones Technologies, Inc. HPT366 (rev 03) Subsystem: Triones Technologies, Inc.: Unknown device 0001 Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 120 (2000ns min, 2000ns max), cache line size 08 Interrupt: pin A routed to IRQ 18 Region 0: I/O ports at b800 [size=8] Region 1: I/O ports at bc00 [size=4] Region 2: I/O ports at c000 [size=8] Region 3: I/O ports at c400 [size=4] Region 4: I/O ports at c800 [size=256] Expansion ROM at <unassigned> [disabled] [size=128K] Capabilities: [60] Power Management version 2 Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME- 00: 03 11 04 00 05 00 30 02 03 00 80 01 08 78 00 00 10: 01 b8 00 00 01 bc 00 00 01 c0 00 00 01 c4 00 00 20: 01 c8 00 00 00 00 00 00 00 00 00 00 03 11 01 00 30: 00 00 00 00 60 00 00 00 00 00 00 00 0a 01 08 08 01:00.0 VGA compatible controller: Matrox Graphics, Inc. MGA G400 AGP (rev 03) (prog-if 00 [VGA]) Subsystem: Matrox Graphics, Inc. Millennium G400 32Mb SGRAM Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 32 (4000ns min, 8000ns max), cache line size 08 Interrupt: pin A routed to IRQ 16 Region 0: Memory at d4000000 (32-bit, prefetchable) [size=32M] Region 1: Memory at d6000000 (32-bit, non-prefetchable) [size=16K] Region 2: Memory at d7000000 (32-bit, non-prefetchable) [size=8M] Expansion ROM at <unassigned> [disabled] [size=64K] Capabilities: [dc] Power Management version 2 Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME- Capabilities: [f0] AGP version 2.0 Status: RQ=31 SBA+ 64bit- FW- Rate=x1,x2 Command: RQ=31 SBA+ AGP+ 64bit- FW- Rate=x1 00: 2b 10 25 05 07 00 90 02 03 00 00 03 08 20 00 00 10: 08 00 00 d4 00 00 00 d6 00 00 00 d7 00 00 00 00 20: 00 00 00 00 00 00 00 00 00 00 00 00 2b 10 f8 19 30: 00 00 00 00 dc 00 00 00 00 00 00 00 0f 01 10 20 02:00.0 SCSI storage controller: Symbios Logic Inc. (formerly NCR) 53c875 (rev 04) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR- FastB2B- Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 72 (4250ns min, 16000ns max), cache line size 08 Interrupt: pin A routed to IRQ 16 Region 0: I/O ports at 9000 [size=256] Region 1: Memory at da001000 (32-bit, non-prefetchable) [size=256] Region 2: Memory at da000000 (32-bit, non-prefetchable) [size=4K] Expansion ROM at <unassigned> [disabled] [size=64K] 00: 00 10 0f 00 47 00 00 02 04 00 00 01 08 48 00 00 10: 01 90 00 00 00 10 00 da 00 00 00 da 00 00 00 00 20: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 30: 00 00 00 00 00 00 00 00 00 00 00 00 0f 01 11 40 02:01.0 SCSI storage controller: Symbios Logic Inc. (formerly NCR) 53c875 (rev 04) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR- FastB2B- Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 72 (4250ns min, 16000ns max), cache line size 08 Interrupt: pin A routed to IRQ 17 Region 0: I/O ports at 9400 [size=256] Region 1: Memory at da002000 (32-bit, non-prefetchable) [size=256] Region 2: Memory at da003000 (32-bit, non-prefetchable) [size=4K] Expansion ROM at <unassigned> [disabled] [size=64K] 00: 00 10 0f 00 47 00 00 02 04 00 00 01 08 48 00 00 10: 01 94 00 00 00 20 00 da 00 30 00 da 00 00 00 00 20: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 30: 00 00 00 00 00 00 00 00 00 00 00 00 0b 01 11 40 02:02.0 Ethernet controller: Digital Equipment Corporation DECchip 21140 [FasterNet] (rev 22) Subsystem: Digital Equipment Corporation: Unknown device 500a Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 96 (5000ns min, 10000ns max), cache line size 08 Interrupt: pin A routed to IRQ 18 Region 0: I/O ports at 9800 [size=128] Region 1: Memory at da004000 (32-bit, non-prefetchable) [size=128] Expansion ROM at <unassigned> [disabled] [size=256K] 00: 11 10 09 00 07 00 80 02 22 00 00 02 08 60 00 00 10: 01 98 00 00 00 40 00 da 00 00 00 00 00 00 00 00 20: 00 00 00 00 00 00 00 00 00 00 00 00 11 10 0a 50 30: 00 00 00 00 00 00 00 00 00 00 00 00 0a 01 14 28 Good luck, Jurriaan -- BOFH excuse #175: OS swapped to disk GNU/Linux 2.4.5-ac5 SMP/ReiserFS 2x1402 bogomips load av: 0.00 0.00 0.00 ^ permalink raw reply [flat|nested] 11+ messages in thread
* Re: interrupt problem with MPS 1.4 / not with MPS 1.1 ? 2001-06-01 5:14 ` thunder7 2001-06-01 5:20 ` Jeff Garzik @ 2001-06-01 17:28 ` Manfred Spraul 2001-06-01 17:41 ` Jeff Garzik 2001-06-01 19:03 ` thunder7 1 sibling, 2 replies; 11+ messages in thread From: Manfred Spraul @ 2001-06-01 17:28 UTC (permalink / raw) To: thunder7; +Cc: linux-kernel, Jeff Garzik thunder7@xs4all.nl wrote: > > :setpci -s 00:07.2 INTERRUPT_LINE=15 > :lspci -vx -s 00:07.2 > 00:07.2 USB Controller: VIA Technologies, Inc. UHCI USB (rev 16) (prog-if 00 [UHCI]) > Subsystem: Unknown device 0925:1234 > Flags: bus master, medium devsel, latency 32, IRQ 19 > I/O ports at a000 [size=32] > Capabilities: [80] Power Management version 2 > 30: 00 00 00 00 80 00 00 00 00 00 00 00 15 04 00 > :setpci -s 00:07.2 INTERRUPT_LINE=19 > :lspci -vx -s 00:07.2 > 00:07.2 USB Controller: VIA Technologies, Inc. UHCI USB (rev 16) (prog-if 00 [UHCI]) > Subsystem: Unknown device 0925:1234 > Flags: bus master, medium devsel, latency 32, IRQ 19 > I/O ports at a000 [size=32] > Capabilities: [80] Power Management version 2 > 30: 00 00 00 00 80 00 00 00 00 00 00 00 19 04 00 00 > > So that is correct. I'll attach all the information from the MPS 1.4 > reboot, in which 00:07.2 happily points at 05, while everything else > thinks it's at 19..... > Could you compile uhci as a module, set the configuration to MPS1.4 and find out with which interrupt line setting it works. I'd try both setpci -s 00:07.2 INTERRUPT_LINE=13 setpci -s 00:07.2 INTERRUPT_LINE=3 [even if 13 works, please try 03 as well. 13 is hexadecimal==19] The via ac97 sound driver contains an irq fixup for this problem. Either a similar fixup is necessary in the uhci driver, or the fixup from the ac97 driver could be moved to the pci-quirks and applied to all devices in the southbridge. -- Manfred ^ permalink raw reply [flat|nested] 11+ messages in thread
* Re: interrupt problem with MPS 1.4 / not with MPS 1.1 ? 2001-06-01 17:28 ` Manfred Spraul @ 2001-06-01 17:41 ` Jeff Garzik 2001-06-01 19:03 ` thunder7 1 sibling, 0 replies; 11+ messages in thread From: Jeff Garzik @ 2001-06-01 17:41 UTC (permalink / raw) To: Manfred Spraul; +Cc: thunder7, linux-kernel Manfred Spraul wrote: > Could you compile uhci as a module, set the configuration to MPS1.4 and > find out with which interrupt line setting it works. > I'd try both > > setpci -s 00:07.2 INTERRUPT_LINE=13 > setpci -s 00:07.2 INTERRUPT_LINE=3 > [even if 13 works, please try 03 as well. 13 is hexadecimal==19] > > The via ac97 sound driver contains an irq fixup for this problem. Either I am not sure this fixup is necessary, though IIRC it did solve some problems. Since this latest round of Via fixups, I would like to remove that little change in via audio, and see it anyone complains. The 686A and 686B docs list no irq after 14. Adrian Cox has said that setting the PCI intr line value actually makes a connection on the PIC, instead of just being a scratchpad register like it is normally. Adrian said the same thing about the USB IRQ, and I presume the other internal irqs (like ACPI) listed for register 0x58 apply as well. -- Jeff Garzik | Disbelief, that's why you fail. Building 1024 | MandrakeSoft | ^ permalink raw reply [flat|nested] 11+ messages in thread
* Re: interrupt problem with MPS 1.4 / not with MPS 1.1 ? 2001-06-01 17:28 ` Manfred Spraul 2001-06-01 17:41 ` Jeff Garzik @ 2001-06-01 19:03 ` thunder7 1 sibling, 0 replies; 11+ messages in thread From: thunder7 @ 2001-06-01 19:03 UTC (permalink / raw) To: Manfred Spraul; +Cc: linux-kernel, jgarzik On Fri, Jun 01, 2001 at 07:28:33PM +0200, Manfred Spraul wrote: > thunder7@xs4all.nl wrote: > > > > :setpci -s 00:07.2 INTERRUPT_LINE=15 > > :lspci -vx -s 00:07.2 > > 00:07.2 USB Controller: VIA Technologies, Inc. UHCI USB (rev 16) (prog-if 00 [UHCI]) > > Subsystem: Unknown device 0925:1234 > > Flags: bus master, medium devsel, latency 32, IRQ 19 > > I/O ports at a000 [size=32] > > Capabilities: [80] Power Management version 2 > > 30: 00 00 00 00 80 00 00 00 00 00 00 00 15 04 00 > > :setpci -s 00:07.2 INTERRUPT_LINE=19 > > :lspci -vx -s 00:07.2 > > 00:07.2 USB Controller: VIA Technologies, Inc. UHCI USB (rev 16) (prog-if 00 [UHCI]) > > Subsystem: Unknown device 0925:1234 > > Flags: bus master, medium devsel, latency 32, IRQ 19 > > I/O ports at a000 [size=32] > > Capabilities: [80] Power Management version 2 > > 30: 00 00 00 00 80 00 00 00 00 00 00 00 19 04 00 00 > > > > So that is correct. I'll attach all the information from the MPS 1.4 > > reboot, in which 00:07.2 happily points at 05, while everything else > > thinks it's at 19..... > > > > Could you compile uhci as a module, set the configuration to MPS1.4 and > find out with which interrupt line setting it works. > I'd try both > > setpci -s 00:07.2 INTERRUPT_LINE=13 no change, still this in /var/log/messages: Jun 1 20:57:48 middle kernel: uhci.c: USB Universal Host Controller Interface driver Jun 1 20:57:48 middle kernel: hub.c: USB new device connect on bus1/1, assigned device number 2 Jun 1 20:57:51 middle kernel: usb_control/bulk_msg: timeout Jun 1 20:57:51 middle kernel: usb.c: USB device not accepting new address=2 (error=-110) Jun 1 20:57:51 middle kernel: hub.c: USB new device connect on bus1/1, assigned device number 3 Jun 1 20:57:54 middle kernel: usb_control/bulk_msg: timeout Jun 1 20:57:54 middle kernel: usb.c: USB device not accepting new address=3 (error=-110) > setpci -s 00:07.2 INTERRUPT_LINE=3 > [even if 13 works, please try 03 as well. 13 is hexadecimal==19] Bingo!! Jun 1 20:59:34 middle kernel: Type: Direct-Access ANSI SCSI revision: 02 Jun 1 20:59:34 middle kernel: Attached scsi removable disk sda at scsi3, channel 0, id 0, lun 0 Jun 1 20:59:34 middle kernel: sda : READ CAPACITY failed. Jun 1 20:59:34 middle kernel: sda : status = 1, message = 00, host = 0, driver = 08 Jun 1 20:59:34 middle kernel: sda : extended sense code = 2 Jun 1 20:59:34 middle kernel: sda : block size assumed to be 512 bytes, disk size 1GB. Jun 1 20:59:34 middle kernel: sda: I/O error: dev 08:00, sector 0 Jun 1 20:59:34 middle kernel: unable to read partition table Jun 1 20:59:34 middle kernel: WARNING: USB Mass Storage data integrity not assured Jun 1 20:59:34 middle kernel: USB Mass Storage device found at 2 > > The via ac97 sound driver contains an irq fixup for this problem. Either > a similar fixup is necessary in the uhci driver, or the fixup from the > ac97 driver could be moved to the pci-quirks and applied to all devices > in the southbridge. > Just to be sure, the lspci -vvvxxx reading of 07.2 after this setpci -s 00:07.2 INTERRUPT_LINE=3 with MPS=1.4 in the bios: 00:07.2 USB Controller: VIA Technologies, Inc. UHCI USB (rev 16) (prog-if 00 [UHCI]) Subsystem: Unknown device 0925:1234 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 32, cache line size 08 Interrupt: pin D routed to IRQ 19 Region 4: I/O ports at a000 [size=32] Capabilities: [80] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME- 00: 06 11 38 30 07 00 10 02 16 00 03 0c 08 20 00 00 10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 20: 01 a0 00 00 00 00 00 00 00 00 00 00 25 09 34 12 30: 00 00 00 00 80 00 00 00 00 00 00 00 03 04 00 00 40: 00 10 03 00 02 00 32 e0 00 00 00 00 00 00 00 00 50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 60: 10 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 80: 01 00 02 00 00 00 00 00 00 00 00 00 00 00 00 00 90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 c0: 00 20 00 00 00 00 00 00 00 00 00 00 00 00 00 00 d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 /proc/interrupts: CPU0 CPU1 0: 22004 24207 IO-APIC-edge timer 1: 2073 2617 IO-APIC-edge keyboard 2: 0 0 XT-PIC cascade 8: 2 0 IO-APIC-edge rtc 14: 240 241 IO-APIC-edge ide0 16: 5342007 5342450 IO-APIC-level sym53c8xx 17: 23 21 IO-APIC-level sym53c8xx, sym53c8xx 18: 6448 6349 IO-APIC-level ide2, ide3, DE500-AA (eth0) 19: 42 42 IO-APIC-level usb-uhci, usb-uhci NMI: 0 0 LOC: 46131 46128 ERR: 0 MIS: 0 Good luck, Jurriaan -- BOFH excuse #317: Internet exceeded Luser level, please wait until a luser logs off before attempting to log back on. GNU/Linux 2.4.5-ac6 SMP/ReiserFS 2x1402 bogomips load av: 0.49 0.12 0.04 ^ permalink raw reply [flat|nested] 11+ messages in thread
end of thread, other threads:[~2001-06-01 19:04 UTC | newest] Thread overview: 11+ messages (download: mbox.gz follow: Atom feed -- links below jump to the message on this page -- 2001-05-31 18:39 interrupt problem with MPS 1.4 / not with MPS 1.1 ? thunder7 2001-05-31 18:06 ` Greg KH 2001-05-31 19:48 ` [lkml]Re: " thunder7 2001-05-31 18:56 ` Greg KH 2001-06-01 8:51 ` thunder7 -- strict thread matches above, loose matches on Subject: below -- 2001-05-31 20:21 [lkml]Re: " Manfred Spraul 2001-05-31 20:27 ` [lkml]Re: " thunder7 2001-05-31 20:45 ` Manfred Spraul 2001-06-01 5:14 ` thunder7 2001-06-01 5:20 ` Jeff Garzik 2001-06-01 5:39 ` thunder7 2001-06-01 17:28 ` Manfred Spraul 2001-06-01 17:41 ` Jeff Garzik 2001-06-01 19:03 ` thunder7
This is a public inbox, see mirroring instructions for how to clone and mirror all data and code used for this inbox