From: Cliff Albert <cliff@oisec.net>
To: Yusuf Goolamabbas <yusufg@outblaze.com>
Cc: linux-kernel@vger.kernel.org, gibbs@scsiguy.com
Subject: Re: aic7xxx errors with 2.4.8-ac7 on 440gx mobo
Date: Mon, 20 Aug 2001 10:55:20 +0200 [thread overview]
Message-ID: <20010820105520.A22087@oisec.net> (raw)
In-Reply-To: <20010820083630.16182.qmail@yusufg.portal2.com>
In-Reply-To: <20010820083630.16182.qmail@yusufg.portal2.com>
On Mon, Aug 20, 2001 at 08:36:30AM -0000, Yusuf Goolamabbas wrote:
> Hi, 2.4.8 and 2.4.9 have no problems compiling and booting on a P3 500
> 440GX mobo (APIC not compiled in the kernel)
>
> With 2.4.8-ac7, I get SCSI errors and the kernel fails to boot. If I
> compile with APIC enabled and APIC on UP also enabled, it boots
> cleanly
I'm getting similair errors on 2.4.8-ac7 on my P2B-S motherboard using
the NEW AIC7xxx driver, the old isn't experiencing these problems. Further
i've been getting these errors since 2.4.3.
> booting with append="noapic", gives the same errors
This also didn't resolve my problems
> SCSI subsystem driver Revision: 1.00
> PCI: Assigned IRQ 11 for device 00:0c.0
> PCI: Sharing IRQ 11 with 00:0c.1
> PCI: Found IRQ 11 for device 00:0c.1
> PCI: Sharing IRQ 11 with 00:0c.0
>
> scsi0 : Adaptec AIC7XXX EISA/VLB/PCI SCSI HBA DRIVER, Rev 6.2.1
> <Adaptec aic7896/97 Ultra2 SCSI adapter>
> aic7896/97: Ultra2 Wide Channel A, SCSI Id=7, 32/255 SCBs
>
> scsi1 : Adaptec AIC7XXX EISA/VLB/PCI SCSI HBA DRIVER, Rev 6.2.1
> <Adaptec aic7896/97 Ultra2 SCSI adapter>
> aic7896/97: Ultra2 Wide Channel B, SCSI Id=7, 32/255 SCBs
SCSI subsystem driver Revision: 1.00
PCI: Found IRQ 14 for device 00:06.0
PCI: Sharing IRQ 14 with 00:04.2
scsi0 : Adaptec AIC7XXX EISA/VLB/PCI SCSI HBA DRIVER, Rev 6.2.1
<Adaptec aic7890/91 Ultra2 SCSI adapter>
aic7890/91: Ultra2 Wide Channel A, SCSI Id=7, 32/255 SCBs
>
> scsi0:0:0:0: Attempting to queue an ABORT message
> scsi0:0:0:0: Command already completed
> aic7xxx_abort returns 8194
> scsi0:0:0:0: Attempting to queue an ABORT message
> scsi0:0:0:0: Device is active, asserting ATN
> Recovery code sleeping
> Recovery code awake
> Timer Expired
> aic7xxx_abort returns 8195
> scsi0:0:0:0: Attempting to queue a TARGET RESET message
> aic7xxx_dev_reset returns 8195
> Recovery SCB completes
> scsi0:0:0:0: Attempting to queue an ABORT message
> ahc_intr: HOST_MSG_LOOP bad phase 0x0
> scsi0:0:0:0: Cmd aborted from QINFIFO
> aic7xxx_abort returns 8194
> scsi: device set offline - not ready or command retry failed after bus reset: host 0 channel 0 id 0 lun 0
> scsi0:0:1:0: Attempting to queue an ABORT message
> scsi0:0:1:0: Command already completed
> aic7xxx_abort returns 8194
> scsi0:0:1:0: Attempting to queue an ABORT message
> scsi0:0:1:0: Command already completed
> aic7xxx_abort returns 8194
> scsi0:0:1:0: Attempting to queue a TARGET RESET message
> scsi0:0:1:0: Is not an active device
> scsi0:0:1:0: Attempting to queue an ABORT message
> scsi0:0:1:0: Command already completed
> aic7xxx_abort returns 8194
scsi0:0:0:0: Attempting to queue an ABORT message
(scsi0:A:0:0): Queuing a recovery SCB
scsi0:0:0:0: Device is disconnected, re-queuing SCB
Recovery code sleeping
(scsi0:A:0:0): Abort Tag Message Sent
(scsi0:A:0:0): SCB 1 - Abort Tag Completed.
Recovery SCB completes
Recovery code awake
aic7xxx_abort returns 8194
scsi0:0:0:0: Attempting to queue an ABORT message
scsi0:0:0:0: Command found on device queue
aic7xxx_abort returns 8194
scsi0:0:0:0: Attempting to queue an ABORT message
(scsi0:A:0:0): Queuing a recovery SCB
scsi0:0:0:0: Device is disconnected, re-queuing SCB
Recovery code sleeping
(scsi0:A:0:0): Abort Tag Message Sent
(scsi0:A:0:0): SCB 4 - Abort Tag Completed.
Recovery SCB completes
Recovery code awake
aic7xxx_abort returns 8194
scsi0:0:0:0: Attempting to queue an ABORT message
(scsi0:A:0:0): Queuing a recovery SCB
scsi0:0:0:0: Device is disconnected, re-queuing SCB
Recovery code sleeping
(scsi0:A:0:0): Abort Tag Message Sent
(scsi0:A:0:0): SCB 2 - Abort Tag Completed.
Recovery SCB completes
Recovery code awake
aic7xxx_abort returns 8194
scsi0:0:0:0: Attempting to queue an ABORT message
(scsi0:A:0:0): Queuing a recovery SCB
scsi0:0:0:0: Device is disconnected, re-queuing SCB
Recovery code sleeping
(scsi0:A:0:0): Abort Tag Message Sent
(scsi0:A:0:0): SCB 9 - Abort Tag Completed.
Recovery SCB completes
Recovery code awake
aic7xxx_abort returns 8194
scsi0:0:0:0: Attempting to queue an ABORT message
(scsi0:A:0:0): Queuing a recovery SCB
scsi0:0:0:0: Device is disconnected, re-queuing SCB
(scsi0:A:0:0): Abort Tag Message Sent
Recovery code sleeping
(scsi0:A:0:0): SCB 0 - Abort Tag Completed.
Recovery SCB completes
Recovery code awake
aic7xxx_abort returns 8194
scsi0:0:0:0: Attempting to queue an ABORT message
scsi0:0:0:0: Command not found
aic7xxx_abort returns 8194
scsi0:0:0:0: Attempting to queue an ABORT message
scsi0:0:0:0: Command found on device queue
aic7xxx_abort returns 8194
scsi0:0:0:0: Attempting to queue an ABORT message
scsi0:0:0:0: Command not found
aic7xxx_abort returns 8194
scsi0:0:0:0: Attempting to queue an ABORT message
scsi0:0:0:0: Command found on device queue
aic7xxx_abort returns 8194
scsi0:0:0:0: Attempting to queue an ABORT message
scsi0:0:0:0: Command not found
aic7xxx_abort returns 8194
scsi0:0:0:0: Attempting to queue an ABORT message
scsi0:0:0:0: Command found on device queue
aic7xxx_abort returns 8194
scsi0:0:0:0: Attempting to queue an ABORT message
scsi0:0:0:0: Command not found
aic7xxx_abort returns 8194
scsi0:0:0:0: Attempting to queue an ABORT message
scsi0:0:0:0: Command found on device queue
aic7xxx_abort returns 8194
scsi0:0:0:0: Attempting to queue an ABORT message
(scsi0:A:0:0): Queuing a recovery SCB
scsi0:0:0:0: Device is disconnected, re-queuing SCB
(scsi0:A:0:0): Abort Tag Message Sent
Recovery code sleeping
(scsi0:A:0:0): SCB 11 - Abort Tag Completed.
Recovery SCB completes
Recovery code awake
aic7xxx_abort returns 8194
scsi0:0:0:0: Attempting to queue an ABORT message
(scsi0:A:0:0): Queuing a recovery SCB
scsi0:0:0:0: Device is disconnected, re-queuing SCB
Recovery code sleeping
(scsi0:A:0:0): Abort Tag Message Sent
(scsi0:A:0:0): SCB 6 - Abort Tag Completed.
Recovery SCB completes
Recovery code awake
aic7xxx_abort returns 8194
scsi0:0:0:0: Attempting to queue an ABORT message
(scsi0:A:0:0): Queuing a recovery SCB
scsi0:0:0:0: Device is disconnected, re-queuing SCB
Recovery code sleeping
(scsi0:A:0:0): Abort Tag Message Sent
(scsi0:A:0:0): SCB 3 - Abort Tag Completed.
Recovery SCB completes
Recovery code awake
aic7xxx_abort returns 8194
scsi0:0:0:0: Attempting to queue a TARGET RESET message
scsi0:0:0:0: Command not found
aic7xxx_dev_reset returns 8194
Device not ready. Make sure there is a disc in the drive.
Device not ready. Make sure there is a disc in the drive.
SCSI device listing is:
Vendor: QUANTUM Model: FIREBALL ST6.4S Rev: 0F0C
Type: Direct-Access ANSI SCSI revision: 02
(scsi0:A:0): 20.000MB/s transfers (20.000MHz, offset 15)
Vendor: IOMEGA Model: ZIP 100 Rev: J.03
Type: Direct-Access ANSI SCSI revision: 02
Vendor: YAMAHA Model: CRW2100S Rev: 1.0H
Type: CD-ROM ANSI SCSI revision: 02
(scsi0:A:5): 20.000MB/s transfers (20.000MHz, offset 7)
Vendor: PLEXTOR Model: CD-ROM PX-32TS Rev: 1.01
Type: CD-ROM ANSI SCSI revision: 02
(scsi0:A:6): 20.000MB/s transfers (20.000MHz, offset 15)
--
Cliff Albert | RIPE: CA3348-RIPE | www.oisec.net
cliff@oisec.net | 6BONE: CA2-6BONE | icq 18461740
next prev parent reply other threads:[~2001-08-20 8:55 UTC|newest]
Thread overview: 69+ messages / expand[flat|nested] mbox.gz Atom feed top
2001-08-20 8:36 aic7xxx errors with 2.4.8-ac7 on 440gx mobo Yusuf Goolamabbas
2001-08-20 8:55 ` Cliff Albert [this message]
2001-08-20 10:37 ` Alan Cox
2001-08-20 10:56 ` Yusuf Goolamabbas
2001-08-20 10:56 ` Alan Cox
2001-08-20 11:13 ` Yusuf Goolamabbas
2001-08-20 11:09 ` Alan Cox
2001-08-20 16:43 ` Doug Ledford
2001-08-20 12:46 ` Stefan Fleiter
2001-08-20 15:19 ` Ville Herva
2001-08-20 20:33 ` Justin T. Gibbs
2001-08-20 16:45 ` Doug Ledford
2001-08-20 17:23 ` Stefan Fleiter
2001-08-20 20:28 ` Justin T. Gibbs
2001-08-21 20:24 ` Stefan Fleiter
2001-08-20 16:21 ` Cliff Albert
2001-08-20 17:23 ` Peter T. Breuer
2001-08-20 17:28 ` Cliff Albert
2001-08-20 20:27 ` Justin T. Gibbs
2001-08-20 20:45 ` Cliff Albert
2001-08-20 21:04 ` Cliff Albert
2001-08-20 21:09 ` Cliff Albert
2001-08-20 21:45 ` Justin T. Gibbs
2001-08-20 22:36 ` aic7xxx with 2.4.9 on 7899P Sven Heinicke
2001-08-21 14:42 ` With Daniel Phillips Patch (was: aic7xxx with 2.4.9 on 7899P) Sven Heinicke
2001-08-21 15:08 ` Daniel Phillips
2001-08-21 16:48 ` Sven Heinicke
2001-08-21 17:18 ` Justin T. Gibbs
2001-08-21 22:49 ` Sven Heinicke
2001-08-22 13:06 ` Gérard Roudier
2001-08-21 17:26 ` Daniel Phillips
2001-08-21 17:55 ` Stephan von Krawczynski
2001-08-21 18:33 ` Justin T. Gibbs
2001-08-22 6:46 ` Jens Axboe
2001-08-22 13:24 ` Justin T. Gibbs
2001-08-22 15:05 ` With Daniel Phillips Patch David S. Miller
2001-08-22 18:21 ` Gérard Roudier
2001-08-22 18:32 ` David S. Miller
2001-08-22 18:32 ` Justin T. Gibbs
2001-08-22 18:46 ` David S. Miller
2001-08-22 19:41 ` Justin T. Gibbs
2001-08-22 20:19 ` David S. Miller
2001-08-22 21:07 ` Gérard Roudier
2001-08-22 21:14 ` David S. Miller
2001-08-22 21:14 ` David S. Miller
2001-08-22 21:40 ` Justin T. Gibbs
2001-08-22 23:09 ` David S. Miller
2001-08-23 0:01 ` Justin T. Gibbs
2001-08-23 0:40 ` David S. Miller
2001-08-23 0:55 ` Justin T. Gibbs
2001-08-23 1:03 ` Matthew Jacob
2001-08-23 1:08 ` David S. Miller
2001-08-23 1:32 ` Justin T. Gibbs
2001-08-23 1:39 ` David S. Miller
2001-08-23 1:49 ` Justin T. Gibbs
2001-08-21 22:44 ` With Daniel Phillips Patch (was: aic7xxx with 2.4.9 on 7899P) Sven Heinicke
2001-08-22 0:58 ` Daniel Phillips
2001-08-22 10:25 ` Marcelo Tosatti
2001-08-22 16:09 ` Sven Heinicke
2001-08-22 15:42 ` Marcelo Tosatti
2001-08-22 20:25 ` Sven Heinicke
2001-08-29 7:30 ` Andrey Nekrasov
2001-09-03 14:58 ` Marcelo Tosatti
2001-08-20 22:55 ` aic7xxx errors with 2.4.8-ac7 on 440gx mobo Cliff Albert
2001-08-21 0:36 ` Justin T. Gibbs
2001-08-21 15:34 ` Gérard Roudier
2001-08-20 21:44 ` Justin T. Gibbs
2001-08-20 21:48 ` Cliff Albert
2001-08-25 7:15 ` Cliff Albert
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20010820105520.A22087@oisec.net \
--to=cliff@oisec.net \
--cc=gibbs@scsiguy.com \
--cc=linux-kernel@vger.kernel.org \
--cc=yusufg@outblaze.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox