Problem with ACPI on Abit KT7,HPT370

Problem with ACPI on Abit KT7,HPT370

[Dominik Geisel]

Hi,

with all 2.4 kernels (latest I tried were 2.4.10 + 2.4.10-ac9), my Abit KT7-RAID
with onboard HPT370 IDE RAID controller, BIOS version 4A, locks up when ACPI
is enabled in the kernel. APM works fine. I enable

CONFIG_PM=Y
CONFIG_ACPI=Y
CONFIG_ACPI_BUSMGR=Y
CONFIG_ACPI_SYS=Y
CONFIG_ACPI_CPU=Y

The following messages could be useful:

this is the bootup messages when ACPI is disabled:
------------------------------------------------------------------------
Oct  8 19:50:31 pc1 kernel: HPT370: IDE controller on PCI bus 00 dev 98
Oct  8 19:50:31 pc1 kernel: PCI: Found IRQ 11 for device 00:13.0
Oct  8 19:50:31 pc1 kernel: HPT370: chipset revision 3
Oct  8 19:50:31 pc1 kernel: HPT370: not 100%% native mode: will probe irqs
later
Oct  8 19:50:31 pc1 kernel:     ide2: BM-DMA at 0xec00-0xec07,
BIOS settings: hde:DMA, hdf:pio
Oct  8 19:50:31 pc1 kernel:     ide3: BM-DMA at 0xec08-0xec0f, BIOS settings:
hdg:pio, hdh:pio
Oct  8 19:50:31 pc1 kernel: hda: IBM-DTTA-351010, ATA DISK drive
Oct  8 19:50:31 pc1 kernel: hdc: SONY CD-RW CRX140E, ATAPI CD/DVD-ROM drive
Oct  8 19:50:31 pc1 kernel: hde: IC35L040AVER07-0, ATA DISK drive
------------------------------------------------------------------------

When ACPI is enabled, it locks up after it detected "hdc: SONY CD-RW",
the HDD access LED stays on and the system hangs until I do a hard reboot.

Contact me if you need further logs or reports.
Dominik Geisel

-- 
Women want mediocre men. And men are working hard to become as medicore
as possible.
GPG public key @ http://www.geisel.info/key.asc
B216 156D 04EE AE0C 4C03  80C2 CE4B DBB3 801B 3CC2

RE: Problem with ACPI on Abit KT7,HPT370

[Dominik Thinay]

Hi 
with kernel 2.4.11-pre3-xfs + i2c CVS-patch + lmsensors it works fine on my
system (Abit Bios KT7_49B0)


CONFIG_PM=y
CONFIG_ACPI=y
CONFIG_ACPI_DEBUG=y
CONFIG_ACPI_BUSMGR=y
CONFIG_ACPI_SYS=y
CONFIG_ACPI_CPU=y
CONFIG_ACPI_BUTTON=y
But i don't use ide cdrom's 

I remember disabled sth in the bios ...but i have forget ... :(

regards dominik


Ps: "IC35L040AVER07-0" works in UDMA(44) or :( I have disabled the entry in the
        blacklist of  hpt366.c (dtla307030,dtla307060) for testing with the new
        mb bios



> Hi,
> 
> with all 2.4 kernels (latest I tried were 2.4.10 + 2.4.10-ac9), my Abit
> KT7-RAID
> with onboard HPT370 IDE RAID controller, BIOS version 4A, locks up when ACPI
> is enabled in the kernel. APM works fine. I enable
> 
> CONFIG_PM=Y
> CONFIG_ACPI=Y
> CONFIG_ACPI_BUSMGR=Y
> CONFIG_ACPI_SYS=Y
> CONFIG_ACPI_CPU=Y
> 
> The following messages could be useful:
> 
> this is the bootup messages when ACPI is disabled:
> ------------------------------------------------------------------------
> Oct  8 19:50:31 pc1 kernel: HPT370: IDE controller on PCI bus 00 dev 98
> Oct  8 19:50:31 pc1 kernel: PCI: Found IRQ 11 for device 00:13.0
> Oct  8 19:50:31 pc1 kernel: HPT370: chipset revision 3
> Oct  8 19:50:31 pc1 kernel: HPT370: not 100%% native mode: will probe irqs
> later
> Oct  8 19:50:31 pc1 kernel:     ide2: BM-DMA at 0xec00-0xec07,
> BIOS settings: hde:DMA, hdf:pio
> Oct  8 19:50:31 pc1 kernel:     ide3: BM-DMA at 0xec08-0xec0f, BIOS settings:
> hdg:pio, hdh:pio
> Oct  8 19:50:31 pc1 kernel: hda: IBM-DTTA-351010, ATA DISK drive
> Oct  8 19:50:31 pc1 kernel: hdc: SONY CD-RW CRX140E, ATAPI CD/DVD-ROM drive
> Oct  8 19:50:31 pc1 kernel: hde: IC35L040AVER07-0, ATA DISK drive
> ------------------------------------------------------------------------
> 
> When ACPI is enabled, it locks up after it detected "hdc: SONY CD-RW",
> the HDD access LED stays on and the system hangs until I do a hard reboot.
> 
> Contact me if you need further logs or reports.
> Dominik Geisel
> 
> -- 
> Women want mediocre men. And men are working hard to become as medicore
> as possible.
> GPG public key @ http://www.geisel.info/key.asc
> B216 156D 04EE AE0C 4C03  80C2 CE4B DBB3 801B 3CC2
> -

-- 
----------------------------------
E-Mail: Dominik Thinay <dominik@unix-ag.org>
Date: 08-Oct-2001

----------------------------------

Re: Problem with ACPI on Abit KT7,HPT370

[Dominik Geisel]

I tried 2.4.10-ac10 with your config and played around with all possible
BIOS settings...the problem persists.

Also, I am now quite sure it broke with BIOS version 3R.


On Mon, Oct 08, 2001 at 10:35:42PM +0200, Dominik Thinay wrote:
> with kernel 2.4.11-pre3-xfs + i2c CVS-patch + lmsensors it works fine on my
> system (Abit Bios KT7_49B0)
> CONFIG_PM=y
> CONFIG_ACPI=y
> CONFIG_ACPI_DEBUG=y
> CONFIG_ACPI_BUSMGR=y
> CONFIG_ACPI_SYS=y
> CONFIG_ACPI_CPU=y
> CONFIG_ACPI_BUTTON=y
> 
> I remember disabled sth in the bios ...but i have forget ... :(

Re: Problem with ACPI on Abit KT7,HPT370

[Xavier Bestel]

le lun 08-10-2001 at 20:10 Dominik Geisel a écrit :

> When ACPI is enabled, it locks up after it detected "hdc: SONY CD-RW",
> the HDD access LED stays on and the system hangs until I do a hard reboot.

ABit VP6, HPT370, same problem here (lock before "hde...")

... plus: locks system on some IDE CDROM read errors, with or without
ACPI.

	Xav

RE: Problem with ACPI on Abit KT7,HPT370

[Arthur Aldridge]

   I'm running a KT7-Raid with bios A9.

   After rebuilding my kernel yesterday (2.4.19-gentoo-r9) with
ACPI I ran into this same issue. I noted that at that time the
devices attached to the HPT370 were reporting at DMA 2.
I realized I'd turned the IDE cables around.

   After fixing that the system worked fine. Early this morning I
decided to move the DVD drive to a different system and replaced
it with an older Samsung CD-ROM and I haven't been able to boot
since. The only change besides the CD-ROM is that my bios
setting were reset and perhaps I don't have exactly the same
settings. Alt-SysRq+b responds, and if I disable the HPT370 the
system boots without issue. I've tried disconnecting the CD-ROM
and disabling DMA at boot, none of which is working.....

I suppose I'll just go back with the HPT370 disabled and compile
a non-acpi kernel to see if it starts working again but this is baffle
the bejesus out of me.

 >Dominik Geisel (dominik_at_geisel.info) Wrote:
 >
 >I tried 2.4.10-ac10 with your config and played around with all possible
 >BIOS settings...the problem persists.
 >Also, I am now quite sure it broke with BIOS version 3R.

 >>On Mon, Oct 08, 2001 at 10:35:42PM +0200, Dominik Thinay wrote:
 >> with kernel 2.4.11-pre3-xfs + i2c CVS-patch + lmsensors it works fine 
on my
 >> system (Abit Bios KT7_49B0)
 >> CONFIG_PM=y
 >> CONFIG_ACPI=y
 >> CONFIG_ACPI_DEBUG=y
 >> CONFIG_ACPI_BUSMGR=y
 >> CONFIG_ACPI_SYS=y
 >> CONFIG_ACPI_CPU=y
 >> CONFIG_ACPI_BUTTON=y
 >>
 >> I remember disabled sth in the bios ...but i have forget ... :(




--
Arthur Aldridge
Sun Certified Solaris Admin
aj@yasashi.net