Re: [bug] 2.4.19-pre4-ac2 hang at boot with ALI15x3 chipset support

public inbox for linux-kernel@vger.kernel.org
 help / color / mirror / Atom feed

* Re: [bug] 2.4.19-pre4-ac2 hang at boot with ALI15x3 chipset support
       [not found] <86387368@toto.iv>
@ 2002-03-28  3:37 ` bhoward
  2002-03-29  1:08   ` James Mayer
  0 siblings, 1 reply; 9+ messages in thread
From: bhoward @ 2002-03-28  3:37 UTC (permalink / raw)
  To: James Mayer; +Cc: linux-kernel

>> > After adding printk calls to alim15x3.c, it seems to hang during the
>> > pci_write_config_byte(isa_dev, 0x79, tmpbyte | 0x02) call on line 588.
>> 
>> Does it work if you comemtn that line out ?

James> No, if the line is commented out I get:

James> hda: status error: status=0x58 { DriveReady SeekComplete DataRequest }
James> hda: drive not ready for command

I ran into this as well under various kernels including 2.4.18.  Try
adding:
    append="idebus=50"

to the lilo stanza for your kernel.

It seems even after I amputated the offending "write" that causes the
lockup, the bus speed was being set to 33MHz instead of 50Mhz.  The
above solved the problem for me.

I don't need to specifically set idebus in the 2.5.7 version of the
driver so I assume something has been corrected in more recent
releases.

For anyone else trying to configure the pcg-c1mrx or pcg-c1mv, I'm
updating linux configuration document as I work through the
setup of the various devices:
    http://hale.org/~bhoward/issue_7/pcg-c1mrx.html

						Bruce

^ permalink raw reply	[flat|nested] 9+ messages in thread

* Re: [bug] 2.4.19-pre4-ac2 hang at boot with ALI15x3 chipset support
  2002-03-28  3:37 ` [bug] 2.4.19-pre4-ac2 hang at boot with ALI15x3 chipset support bhoward
@ 2002-03-29  1:08   ` James Mayer
  0 siblings, 0 replies; 9+ messages in thread
From: James Mayer @ 2002-03-29  1:08 UTC (permalink / raw)
  To: linux-kernel

> James> hda: status error: status=0x58 { DriveReady SeekComplete DataRequest }
> James> hda: drive not ready for command
> 
> I ran into this as well under various kernels including 2.4.18.  Try
> adding:
>     append="idebus=50"
> 
> to the lilo stanza for your kernel.
> 
> It seems even after I amputated the offending "write" that causes the
> lockup, the bus speed was being set to 33MHz instead of 50Mhz.  The
> above solved the problem for me.

This worked for me as well -- interesting.

> For anyone else trying to configure the pcg-c1mrx or pcg-c1mv, I'm
> updating linux configuration document as I work through the
> setup of the various devices:
>     http://hale.org/~bhoward/issue_7/pcg-c1mrx.html

Good information there.  Oddly enough, I don't need to specify the
pci=conf2, though.

Thanks to everyone for the speedy assistance!
 - James

^ permalink raw reply	[flat|nested] 9+ messages in thread

[parent not found: <124088188@toto.iv>]

* Re: [bug] 2.4.19-pre4-ac2 hang at boot with ALI15x3 chipset support
       [not found] <124088188@toto.iv>
@ 2002-03-29 10:01 ` bhoward
  0 siblings, 0 replies; 9+ messages in thread
From: bhoward @ 2002-03-29 10:01 UTC (permalink / raw)
  To: James Mayer; +Cc: linux-kernel

James> Good information there.  Oddly enough, I don't need to specify the
James> pci=conf2, though.

Remember that you only need the pci=conf2 to get past the lockup bug
when doing an initial installation from CDROM.  After that, once you
have installed a kernel updated with the patch to alim15x3.c, the need
for it goes away (and in fact, continuing to use pci=conf2 will
actually prevent many of the other devices from being properly
recognized).

					Cheers,
					Bruce

^ permalink raw reply	[flat|nested] 9+ messages in thread

* [bug] 2.4.19-pre4-ac2 hang at boot with ALI15x3 chipset support
@ 2002-03-27 23:38 James Mayer
  2002-03-27 23:52 ` Brian D Heaton
                   ` (2 more replies)
  0 siblings, 3 replies; 9+ messages in thread
From: James Mayer @ 2002-03-27 23:38 UTC (permalink / raw)
  To: linux-kernel

Hi,

I'm seeing a kernel hang at boot with the ALI15x3 driver on a Sony
PCG-C1MV/M with 2.4.19-pre4-ac2.

The kernel hangs right after printing
ALI15X3: chipset revision 196
ALI15X3: not 100% native mode: will probe irqs later

After adding printk calls to alim15x3.c, it seems to hang during the
pci_write_config_byte(isa_dev, 0x79, tmpbyte | 0x02) call on line 588.

The kernel successfully loads if I build without ALI15x3 support,
printing these messages:

ALI15X3: chipset revision 196
ALI15X3: not 100% native mode: will probe irqs later
ALI15X3: simplex device:  DMA disabled
ide0: ALI15X3 Bus-Master DMA disabled (BIOS)
ALI15X3: simplex device:  DMA disabled
ide1: ALI15X3 Bus-Master DMA disabled (BIOS)
hda: IC25N020ATDA04-0, ATA DISK drive

Is the ALI15x3 driver falsely enabling udma on my system?

ide0=nodma doesn't help, either...

I'm appending the output from lspci -vv in case that helps.

Thanks for any help... 
 - James

00:00.0 Host bridge: Transmeta Corporation LongRun Northbridge (rev 01)
	Subsystem: Sony Corporation: Unknown device 80ec
	Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
	Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR-
	Latency: 0
	Region 0: Memory at e8000000 (32-bit, non-prefetchable) [size=1M]

00:00.1 RAM memory: Transmeta Corporation SDRAM controller
	Subsystem: Sony Corporation: Unknown device 80ec
	Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
	Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-

00:00.2 RAM memory: Transmeta Corporation BIOS scratchpad
	Subsystem: Sony Corporation: Unknown device 80ec
	Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
	Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-

00:06.0 Multimedia audio controller: Acer Laboratories Inc. [ALi] M5451 PCI South Bridge Audio (rev 02)
	Subsystem: Sony Corporation: Unknown device 80ec
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
	Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR+ <PERR+
	Latency: 64 (500ns min, 6000ns max)
	Interrupt: pin A routed to IRQ 9
	Region 0: I/O ports at 1800 [size=256]
	Region 1: Memory at e8100000 (32-bit, non-prefetchable) [size=4K]
	Capabilities: <available only to root>

00:07.0 ISA bridge: Acer Laboratories Inc. [ALi] M1533 PCI to ISA Bridge [Aladdin IV]
	Subsystem: Sony Corporation: Unknown device 80ec
	Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
	Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
	Latency: 0
	Capabilities: <available only to root>

00:08.0 Modem: Acer Laboratories Inc. [ALi]: Unknown device 5457 (prog-if 00 [Generic])
	Subsystem: Sony Corporation: Unknown device 80ec
	Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
	Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
	Interrupt: pin A routed to IRQ 9
	Region 0: Memory at e8101000 (32-bit, non-prefetchable) [disabled] [size=4K]
	Region 1: I/O ports at 1c00 [disabled] [size=256]
	Capabilities: <available only to root>

00:09.0 FireWire (IEEE 1394): Texas Instruments: Unknown device 8021 (rev 02) (prog-if 10 [OHCI])
	Subsystem: Sony Corporation: Unknown device 80ec
	Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B-
	Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
	Latency: 64 (750ns min, 1000ns max), cache line size 08
	Interrupt: pin A routed to IRQ 9
	Region 0: Memory at e8102000 (32-bit, non-prefetchable) [size=2K]
	Region 1: Memory at e8104000 (32-bit, non-prefetchable) [size=16K]
	Capabilities: <available only to root>

00:0a.0 Multimedia controller: Citicorp TTI: Unknown device 2011
	Subsystem: Sony Corporation: Unknown device 80ec
	Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
	Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
	Interrupt: pin A routed to IRQ 9
	Region 0: I/O ports at 2000 [disabled] [size=256]
	Region 1: Memory at e8200000 (32-bit, non-prefetchable) [disabled] [size=1M]
	Capabilities: <available only to root>

00:0b.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8139 (rev 10)
	Subsystem: Sony Corporation: Unknown device 80ec
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
	Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
	Latency: 64 (8000ns min, 16000ns max)
	Interrupt: pin A routed to IRQ 9
	Region 0: I/O ports at 2400 [size=256]
	Region 1: Memory at e8102800 (32-bit, non-prefetchable) [size=256]
	Capabilities: <available only to root>

00:0c.0 VGA compatible controller: ATI Technologies Inc Radeon Mobility M6 LY (prog-if 00 [VGA])
	Subsystem: Sony Corporation: Unknown device 80ec
	Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping+ SERR- FastB2B-
	Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
	Interrupt: pin A routed to IRQ 9
	Region 0: Memory at f0000000 (32-bit, prefetchable) [size=128M]
	Region 1: I/O ports at 2800 [size=256]
	Region 2: Memory at e8110000 (32-bit, non-prefetchable) [size=64K]
	Expansion ROM at <unassigned> [disabled] [size=128K]
	Capabilities: <available only to root>

00:0f.0 USB Controller: Acer Laboratories Inc. [ALi] M5237 USB (rev 03) (prog-if 10 [OHCI])
	Subsystem: Sony Corporation: Unknown device 80ec
	Control: I/O- Mem- BusMaster- SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B-
	Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
	Interrupt: pin A routed to IRQ 9
	Region 0: Memory at e8103000 (32-bit, non-prefetchable) [disabled] [size=4K]
	Capabilities: <available only to root>

00:10.0 IDE interface: Acer Laboratories Inc. [ALi] M5229 IDE (rev c4) (prog-if a0)
	Subsystem: Sony Corporation: Unknown device 80ec
	Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
	Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
	Latency: 64 (500ns min, 1000ns max)
	Interrupt: pin A routed to IRQ 0
	Region 0: [virtual] I/O ports at 01f0 [size=16]
	Region 1: [virtual] I/O ports at 03f4
	Region 2: [virtual] I/O ports at 0170 [size=16]
	Region 3: [virtual] I/O ports at 0374
	Region 4: I/O ports at 1400 [size=16]
	Capabilities: <available only to root>

00:11.0 Non-VGA unclassified device: Acer Laboratories Inc. [ALi] M7101 PMU
	Subsystem: Sony Corporation: Unknown device 80ec
	Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
	Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-

00:12.0 CardBus bridge: Ricoh Co Ltd RL5c475 (rev 80)
	Subsystem: Sony Corporation: Unknown device 80ec
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
	Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
	Latency: 168
	Interrupt: pin A routed to IRQ 9
	Region 0: Memory at 10000000 (32-bit, non-prefetchable) [size=4K]
	Bus: primary=00, secondary=01, subordinate=01, sec-latency=176
	Memory window 0: 10400000-107ff000 (prefetchable)
	Memory window 1: 10800000-10bff000
	I/O window 0: 00004000-000040ff
	I/O window 1: 00004400-000044ff
	BridgeCtl: Parity- SERR- ISA- VGA- MAbort- >Reset- 16bInt+ PostWrite+
	16-bit legacy interface ports at 0001

00:14.0 USB Controller: Acer Laboratories Inc. [ALi] M5237 USB (rev 03) (prog-if 10 [OHCI])
	Subsystem: Sony Corporation: Unknown device 80ec
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B-
	Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
	Latency: 64 (20000ns max), cache line size 08
	Interrupt: pin A routed to IRQ 9
	Region 0: Memory at 000e0000 (32-bit, non-prefetchable) [size=4K]
	Capabilities: <available only to root>


^ permalink raw reply	[flat|nested] 9+ messages in thread

* Re: [bug] 2.4.19-pre4-ac2 hang at boot with ALI15x3 chipset support
  2002-03-27 23:38 James Mayer
@ 2002-03-27 23:52 ` Brian D Heaton
  2002-03-27 23:59 ` Andre Hedrick
  2002-03-28  0:04 ` Alan Cox
  2 siblings, 0 replies; 9+ messages in thread
From: Brian D Heaton @ 2002-03-27 23:52 UTC (permalink / raw)
  To: James Mayer; +Cc: linux-kernel

I had the same issue with my Lifebook P-2040.  I found a patch on-line
to work around the issue.  I'll look for it and send you a link.

			THX/BDH


On Wed, 2002-03-27 at 18:38, James Mayer wrote:
> Hi,
> 
> I'm seeing a kernel hang at boot with the ALI15x3 driver on a Sony
> PCG-C1MV/M with 2.4.19-pre4-ac2.
> 
> The kernel hangs right after printing
> ALI15X3: chipset revision 196
> ALI15X3: not 100% native mode: will probe irqs later
> 
> After adding printk calls to alim15x3.c, it seems to hang during the
> pci_write_config_byte(isa_dev, 0x79, tmpbyte | 0x02) call on line 588.
> 
> The kernel successfully loads if I build without ALI15x3 support,
> printing these messages:
> 
> ALI15X3: chipset revision 196
> ALI15X3: not 100% native mode: will probe irqs later
> ALI15X3: simplex device:  DMA disabled
> ide0: ALI15X3 Bus-Master DMA disabled (BIOS)
> ALI15X3: simplex device:  DMA disabled
> ide1: ALI15X3 Bus-Master DMA disabled (BIOS)
> hda: IC25N020ATDA04-0, ATA DISK drive
> 
> Is the ALI15x3 driver falsely enabling udma on my system?
> 
> ide0=nodma doesn't help, either...
> 
> I'm appending the output from lspci -vv in case that helps.
> 
> Thanks for any help... 
>  - James
> 
> 00:00.0 Host bridge: Transmeta Corporation LongRun Northbridge (rev 01)
> 	Subsystem: Sony Corporation: Unknown device 80ec
> 	Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
> 	Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR-
> 	Latency: 0
> 	Region 0: Memory at e8000000 (32-bit, non-prefetchable) [size=1M]
> 
> 00:00.1 RAM memory: Transmeta Corporation SDRAM controller
> 	Subsystem: Sony Corporation: Unknown device 80ec
> 	Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
> 	Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
> 
> 00:00.2 RAM memory: Transmeta Corporation BIOS scratchpad
> 	Subsystem: Sony Corporation: Unknown device 80ec
> 	Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
> 	Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
> 
> 00:06.0 Multimedia audio controller: Acer Laboratories Inc. [ALi] M5451 PCI South Bridge Audio (rev 02)
> 	Subsystem: Sony Corporation: Unknown device 80ec
> 	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
> 	Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR+ <PERR+
> 	Latency: 64 (500ns min, 6000ns max)
> 	Interrupt: pin A routed to IRQ 9
> 	Region 0: I/O ports at 1800 [size=256]
> 	Region 1: Memory at e8100000 (32-bit, non-prefetchable) [size=4K]
> 	Capabilities: <available only to root>
> 
> 00:07.0 ISA bridge: Acer Laboratories Inc. [ALi] M1533 PCI to ISA Bridge [Aladdin IV]
> 	Subsystem: Sony Corporation: Unknown device 80ec
> 	Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
> 	Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
> 	Latency: 0
> 	Capabilities: <available only to root>
> 
> 00:08.0 Modem: Acer Laboratories Inc. [ALi]: Unknown device 5457 (prog-if 00 [Generic])
> 	Subsystem: Sony Corporation: Unknown device 80ec
> 	Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
> 	Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
> 	Interrupt: pin A routed to IRQ 9
> 	Region 0: Memory at e8101000 (32-bit, non-prefetchable) [disabled] [size=4K]
> 	Region 1: I/O ports at 1c00 [disabled] [size=256]
> 	Capabilities: <available only to root>
> 
> 00:09.0 FireWire (IEEE 1394): Texas Instruments: Unknown device 8021 (rev 02) (prog-if 10 [OHCI])
> 	Subsystem: Sony Corporation: Unknown device 80ec
> 	Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B-
> 	Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
> 	Latency: 64 (750ns min, 1000ns max), cache line size 08
> 	Interrupt: pin A routed to IRQ 9
> 	Region 0: Memory at e8102000 (32-bit, non-prefetchable) [size=2K]
> 	Region 1: Memory at e8104000 (32-bit, non-prefetchable) [size=16K]
> 	Capabilities: <available only to root>
> 
> 00:0a.0 Multimedia controller: Citicorp TTI: Unknown device 2011
> 	Subsystem: Sony Corporation: Unknown device 80ec
> 	Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
> 	Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
> 	Interrupt: pin A routed to IRQ 9
> 	Region 0: I/O ports at 2000 [disabled] [size=256]
> 	Region 1: Memory at e8200000 (32-bit, non-prefetchable) [disabled] [size=1M]
> 	Capabilities: <available only to root>
> 
> 00:0b.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8139 (rev 10)
> 	Subsystem: Sony Corporation: Unknown device 80ec
> 	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
> 	Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
> 	Latency: 64 (8000ns min, 16000ns max)
> 	Interrupt: pin A routed to IRQ 9
> 	Region 0: I/O ports at 2400 [size=256]
> 	Region 1: Memory at e8102800 (32-bit, non-prefetchable) [size=256]
> 	Capabilities: <available only to root>
> 
> 00:0c.0 VGA compatible controller: ATI Technologies Inc Radeon Mobility M6 LY (prog-if 00 [VGA])
> 	Subsystem: Sony Corporation: Unknown device 80ec
> 	Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping+ SERR- FastB2B-
> 	Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
> 	Interrupt: pin A routed to IRQ 9
> 	Region 0: Memory at f0000000 (32-bit, prefetchable) [size=128M]
> 	Region 1: I/O ports at 2800 [size=256]
> 	Region 2: Memory at e8110000 (32-bit, non-prefetchable) [size=64K]
> 	Expansion ROM at <unassigned> [disabled] [size=128K]
> 	Capabilities: <available only to root>
> 
> 00:0f.0 USB Controller: Acer Laboratories Inc. [ALi] M5237 USB (rev 03) (prog-if 10 [OHCI])
> 	Subsystem: Sony Corporation: Unknown device 80ec
> 	Control: I/O- Mem- BusMaster- SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B-
> 	Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
> 	Interrupt: pin A routed to IRQ 9
> 	Region 0: Memory at e8103000 (32-bit, non-prefetchable) [disabled] [size=4K]
> 	Capabilities: <available only to root>
> 
> 00:10.0 IDE interface: Acer Laboratories Inc. [ALi] M5229 IDE (rev c4) (prog-if a0)
> 	Subsystem: Sony Corporation: Unknown device 80ec
> 	Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
> 	Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
> 	Latency: 64 (500ns min, 1000ns max)
> 	Interrupt: pin A routed to IRQ 0
> 	Region 0: [virtual] I/O ports at 01f0 [size=16]
> 	Region 1: [virtual] I/O ports at 03f4
> 	Region 2: [virtual] I/O ports at 0170 [size=16]
> 	Region 3: [virtual] I/O ports at 0374
> 	Region 4: I/O ports at 1400 [size=16]
> 	Capabilities: <available only to root>
> 
> 00:11.0 Non-VGA unclassified device: Acer Laboratories Inc. [ALi] M7101 PMU
> 	Subsystem: Sony Corporation: Unknown device 80ec
> 	Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
> 	Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
> 
> 00:12.0 CardBus bridge: Ricoh Co Ltd RL5c475 (rev 80)
> 	Subsystem: Sony Corporation: Unknown device 80ec
> 	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
> 	Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
> 	Latency: 168
> 	Interrupt: pin A routed to IRQ 9
> 	Region 0: Memory at 10000000 (32-bit, non-prefetchable) [size=4K]
> 	Bus: primary=00, secondary=01, subordinate=01, sec-latency=176
> 	Memory window 0: 10400000-107ff000 (prefetchable)
> 	Memory window 1: 10800000-10bff000
> 	I/O window 0: 00004000-000040ff
> 	I/O window 1: 00004400-000044ff
> 	BridgeCtl: Parity- SERR- ISA- VGA- MAbort- >Reset- 16bInt+ PostWrite+
> 	16-bit legacy interface ports at 0001
> 
> 00:14.0 USB Controller: Acer Laboratories Inc. [ALi] M5237 USB (rev 03) (prog-if 10 [OHCI])
> 	Subsystem: Sony Corporation: Unknown device 80ec
> 	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B-
> 	Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
> 	Latency: 64 (20000ns max), cache line size 08
> 	Interrupt: pin A routed to IRQ 9
> 	Region 0: Memory at 000e0000 (32-bit, non-prefetchable) [size=4K]
> 	Capabilities: <available only to root>
> 
> -
> To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
> the body of a message to majordomo@vger.kernel.org
> More majordomo info at  http://vger.kernel.org/majordomo-info.html
> Please read the FAQ at  http://www.tux.org/lkml/
> 



^ permalink raw reply	[flat|nested] 9+ messages in thread

* Re: [bug] 2.4.19-pre4-ac2 hang at boot with ALI15x3 chipset support
  2002-03-27 23:38 James Mayer
  2002-03-27 23:52 ` Brian D Heaton
@ 2002-03-27 23:59 ` Andre Hedrick
  2002-03-28  0:04 ` Alan Cox
  2 siblings, 0 replies; 9+ messages in thread
From: Andre Hedrick @ 2002-03-27 23:59 UTC (permalink / raw)
  To: James Mayer; +Cc: linux-kernel


This problem is being addressed at ALI with the help of Sony.
I can not tell you the issue because I have not been authorized.

Cheers,

On Wed, 27 Mar 2002, James Mayer wrote:

> Hi,
> 
> I'm seeing a kernel hang at boot with the ALI15x3 driver on a Sony
> PCG-C1MV/M with 2.4.19-pre4-ac2.
> 
> The kernel hangs right after printing
> ALI15X3: chipset revision 196
> ALI15X3: not 100% native mode: will probe irqs later
> 
> After adding printk calls to alim15x3.c, it seems to hang during the
> pci_write_config_byte(isa_dev, 0x79, tmpbyte | 0x02) call on line 588.
> 
> The kernel successfully loads if I build without ALI15x3 support,
> printing these messages:
> 
> ALI15X3: chipset revision 196
> ALI15X3: not 100% native mode: will probe irqs later
> ALI15X3: simplex device:  DMA disabled
> ide0: ALI15X3 Bus-Master DMA disabled (BIOS)
> ALI15X3: simplex device:  DMA disabled
> ide1: ALI15X3 Bus-Master DMA disabled (BIOS)
> hda: IC25N020ATDA04-0, ATA DISK drive
> 
> Is the ALI15x3 driver falsely enabling udma on my system?
> 
> ide0=nodma doesn't help, either...
> 
> I'm appending the output from lspci -vv in case that helps.
> 
> Thanks for any help... 
>  - James
> 
> 00:00.0 Host bridge: Transmeta Corporation LongRun Northbridge (rev 01)
> 	Subsystem: Sony Corporation: Unknown device 80ec
> 	Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
> 	Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR-
> 	Latency: 0
> 	Region 0: Memory at e8000000 (32-bit, non-prefetchable) [size=1M]
> 
> 00:00.1 RAM memory: Transmeta Corporation SDRAM controller
> 	Subsystem: Sony Corporation: Unknown device 80ec
> 	Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
> 	Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
> 
> 00:00.2 RAM memory: Transmeta Corporation BIOS scratchpad
> 	Subsystem: Sony Corporation: Unknown device 80ec
> 	Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
> 	Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
> 
> 00:06.0 Multimedia audio controller: Acer Laboratories Inc. [ALi] M5451 PCI South Bridge Audio (rev 02)
> 	Subsystem: Sony Corporation: Unknown device 80ec
> 	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
> 	Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR+ <PERR+
> 	Latency: 64 (500ns min, 6000ns max)
> 	Interrupt: pin A routed to IRQ 9
> 	Region 0: I/O ports at 1800 [size=256]
> 	Region 1: Memory at e8100000 (32-bit, non-prefetchable) [size=4K]
> 	Capabilities: <available only to root>
> 
> 00:07.0 ISA bridge: Acer Laboratories Inc. [ALi] M1533 PCI to ISA Bridge [Aladdin IV]
> 	Subsystem: Sony Corporation: Unknown device 80ec
> 	Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
> 	Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
> 	Latency: 0
> 	Capabilities: <available only to root>
> 
> 00:08.0 Modem: Acer Laboratories Inc. [ALi]: Unknown device 5457 (prog-if 00 [Generic])
> 	Subsystem: Sony Corporation: Unknown device 80ec
> 	Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
> 	Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
> 	Interrupt: pin A routed to IRQ 9
> 	Region 0: Memory at e8101000 (32-bit, non-prefetchable) [disabled] [size=4K]
> 	Region 1: I/O ports at 1c00 [disabled] [size=256]
> 	Capabilities: <available only to root>
> 
> 00:09.0 FireWire (IEEE 1394): Texas Instruments: Unknown device 8021 (rev 02) (prog-if 10 [OHCI])
> 	Subsystem: Sony Corporation: Unknown device 80ec
> 	Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B-
> 	Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
> 	Latency: 64 (750ns min, 1000ns max), cache line size 08
> 	Interrupt: pin A routed to IRQ 9
> 	Region 0: Memory at e8102000 (32-bit, non-prefetchable) [size=2K]
> 	Region 1: Memory at e8104000 (32-bit, non-prefetchable) [size=16K]
> 	Capabilities: <available only to root>
> 
> 00:0a.0 Multimedia controller: Citicorp TTI: Unknown device 2011
> 	Subsystem: Sony Corporation: Unknown device 80ec
> 	Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
> 	Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
> 	Interrupt: pin A routed to IRQ 9
> 	Region 0: I/O ports at 2000 [disabled] [size=256]
> 	Region 1: Memory at e8200000 (32-bit, non-prefetchable) [disabled] [size=1M]
> 	Capabilities: <available only to root>
> 
> 00:0b.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8139 (rev 10)
> 	Subsystem: Sony Corporation: Unknown device 80ec
> 	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
> 	Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
> 	Latency: 64 (8000ns min, 16000ns max)
> 	Interrupt: pin A routed to IRQ 9
> 	Region 0: I/O ports at 2400 [size=256]
> 	Region 1: Memory at e8102800 (32-bit, non-prefetchable) [size=256]
> 	Capabilities: <available only to root>
> 
> 00:0c.0 VGA compatible controller: ATI Technologies Inc Radeon Mobility M6 LY (prog-if 00 [VGA])
> 	Subsystem: Sony Corporation: Unknown device 80ec
> 	Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping+ SERR- FastB2B-
> 	Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
> 	Interrupt: pin A routed to IRQ 9
> 	Region 0: Memory at f0000000 (32-bit, prefetchable) [size=128M]
> 	Region 1: I/O ports at 2800 [size=256]
> 	Region 2: Memory at e8110000 (32-bit, non-prefetchable) [size=64K]
> 	Expansion ROM at <unassigned> [disabled] [size=128K]
> 	Capabilities: <available only to root>
> 
> 00:0f.0 USB Controller: Acer Laboratories Inc. [ALi] M5237 USB (rev 03) (prog-if 10 [OHCI])
> 	Subsystem: Sony Corporation: Unknown device 80ec
> 	Control: I/O- Mem- BusMaster- SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B-
> 	Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
> 	Interrupt: pin A routed to IRQ 9
> 	Region 0: Memory at e8103000 (32-bit, non-prefetchable) [disabled] [size=4K]
> 	Capabilities: <available only to root>
> 
> 00:10.0 IDE interface: Acer Laboratories Inc. [ALi] M5229 IDE (rev c4) (prog-if a0)
> 	Subsystem: Sony Corporation: Unknown device 80ec
> 	Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
> 	Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
> 	Latency: 64 (500ns min, 1000ns max)
> 	Interrupt: pin A routed to IRQ 0
> 	Region 0: [virtual] I/O ports at 01f0 [size=16]
> 	Region 1: [virtual] I/O ports at 03f4
> 	Region 2: [virtual] I/O ports at 0170 [size=16]
> 	Region 3: [virtual] I/O ports at 0374
> 	Region 4: I/O ports at 1400 [size=16]
> 	Capabilities: <available only to root>
> 
> 00:11.0 Non-VGA unclassified device: Acer Laboratories Inc. [ALi] M7101 PMU
> 	Subsystem: Sony Corporation: Unknown device 80ec
> 	Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
> 	Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
> 
> 00:12.0 CardBus bridge: Ricoh Co Ltd RL5c475 (rev 80)
> 	Subsystem: Sony Corporation: Unknown device 80ec
> 	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
> 	Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
> 	Latency: 168
> 	Interrupt: pin A routed to IRQ 9
> 	Region 0: Memory at 10000000 (32-bit, non-prefetchable) [size=4K]
> 	Bus: primary=00, secondary=01, subordinate=01, sec-latency=176
> 	Memory window 0: 10400000-107ff000 (prefetchable)
> 	Memory window 1: 10800000-10bff000
> 	I/O window 0: 00004000-000040ff
> 	I/O window 1: 00004400-000044ff
> 	BridgeCtl: Parity- SERR- ISA- VGA- MAbort- >Reset- 16bInt+ PostWrite+
> 	16-bit legacy interface ports at 0001
> 
> 00:14.0 USB Controller: Acer Laboratories Inc. [ALi] M5237 USB (rev 03) (prog-if 10 [OHCI])
> 	Subsystem: Sony Corporation: Unknown device 80ec
> 	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B-
> 	Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
> 	Latency: 64 (20000ns max), cache line size 08
> 	Interrupt: pin A routed to IRQ 9
> 	Region 0: Memory at 000e0000 (32-bit, non-prefetchable) [size=4K]
> 	Capabilities: <available only to root>
> 
> -
> To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
> the body of a message to majordomo@vger.kernel.org
> More majordomo info at  http://vger.kernel.org/majordomo-info.html
> Please read the FAQ at  http://www.tux.org/lkml/
> 

Andre Hedrick
LAD Storage Consulting Group


^ permalink raw reply	[flat|nested] 9+ messages in thread

* Re: [bug] 2.4.19-pre4-ac2 hang at boot with ALI15x3 chipset support
  2002-03-27 23:38 James Mayer
  2002-03-27 23:52 ` Brian D Heaton
  2002-03-27 23:59 ` Andre Hedrick
@ 2002-03-28  0:04 ` Alan Cox
  2002-03-28  0:21   ` James Mayer
  2 siblings, 1 reply; 9+ messages in thread
From: Alan Cox @ 2002-03-28  0:04 UTC (permalink / raw)
  To: James Mayer; +Cc: linux-kernel

> After adding printk calls to alim15x3.c, it seems to hang during the
> pci_write_config_byte(isa_dev, 0x79, tmpbyte | 0x02) call on line 588.

Does it work if you comemtn that line out ?

^ permalink raw reply	[flat|nested] 9+ messages in thread

* Re: [bug] 2.4.19-pre4-ac2 hang at boot with ALI15x3 chipset support
  2002-03-28  0:04 ` Alan Cox
@ 2002-03-28  0:21   ` James Mayer
  2002-03-28  0:30     ` Andre Hedrick
  0 siblings, 1 reply; 9+ messages in thread
From: James Mayer @ 2002-03-28  0:21 UTC (permalink / raw)
  To: linux-kernel

On Thu, Mar 28, 2002 at 12:04:33AM +0000, Alan Cox wrote:
> > After adding printk calls to alim15x3.c, it seems to hang during the
> > pci_write_config_byte(isa_dev, 0x79, tmpbyte | 0x02) call on line 588.
> 
> Does it work if you comemtn that line out ?

No, if the line is commented out I get:

hda: status error: status=0x58 { DriveReady SeekComplete DataRequest }
hda: drive not ready for command

 . . . and then the kernel panics because it can't find init.

^ permalink raw reply	[flat|nested] 9+ messages in thread

* Re: [bug] 2.4.19-pre4-ac2 hang at boot with ALI15x3 chipset support
  2002-03-28  0:21   ` James Mayer
@ 2002-03-28  0:30     ` Andre Hedrick
  0 siblings, 0 replies; 9+ messages in thread
From: Andre Hedrick @ 2002-03-28  0:30 UTC (permalink / raw)
  To: James Mayer; +Cc: linux-kernel

On Wed, 27 Mar 2002, James Mayer wrote:

> On Thu, Mar 28, 2002 at 12:04:33AM +0000, Alan Cox wrote:
> > > After adding printk calls to alim15x3.c, it seems to hang during the
> > > pci_write_config_byte(isa_dev, 0x79, tmpbyte | 0x02) call on line 588.
> > 
> > Does it work if you comemtn that line out ?
> 
> No, if the line is commented out I get:
> 
> hda: status error: status=0x58 { DriveReady SeekComplete DataRequest }
> hda: drive not ready for command

Translation the HOST is not setup and the enable hooks are broken.
If you write to those bits it will tank the controller, and that is as
much as I can come forward on at this point.  This is appears to be
exclusive to the TransMeta based NorthBridge + ALI south bridge.

Regards,

Andre Hedrick
LAD Storage Consulting Group


^ permalink raw reply	[flat|nested] 9+ messages in thread

end of thread, other threads:[~2002-03-29 10:02 UTC | newest]

Thread overview: 9+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
     [not found] <86387368@toto.iv>
2002-03-28  3:37 ` [bug] 2.4.19-pre4-ac2 hang at boot with ALI15x3 chipset support bhoward
2002-03-29  1:08   ` James Mayer
     [not found] <124088188@toto.iv>
2002-03-29 10:01 ` bhoward
2002-03-27 23:38 James Mayer
2002-03-27 23:52 ` Brian D Heaton
2002-03-27 23:59 ` Andre Hedrick
2002-03-28  0:04 ` Alan Cox
2002-03-28  0:21   ` James Mayer
2002-03-28  0:30     ` Andre Hedrick

This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox