From: Vojtech Pavlik <vojtech@suse.cz>
To: Fran?ois Cami <stilgar2k@wanadoo.fr>
Cc: Vojtech Pavlik <vojtech@suse.cz>,
linux-kernel@vger.kernel.org, martin@dalecki.de
Subject: Re: Anyone with an ICH2 or ICH3 Intel southbridge and UDMA133 harddrive willing to test?
Date: Sat, 30 Mar 2002 14:09:10 +0100 [thread overview]
Message-ID: <20020330140910.A731@ucw.cz> (raw)
In-Reply-To: <20020330124208.A537@ucw.cz> <3CA5B628.2010202@wanadoo.fr>
[-- Attachment #1: Type: text/plain, Size: 1006 bytes --]
On Sat, Mar 30, 2002 at 01:57:12PM +0100, Fran?ois Cami wrote:
> Vojtech Pavlik wrote:
> > Hi!
> >
> > I think it should be possible to make the ICH2 and ICH3 Intel chips
> > (82801BA and 82801CA) do UDMA133. (Intel only says they can do UDMA100).
> > If anyone running a 2.5 kernel with an Intel mainboard with one of those
> > chips and a UDMA133 capable harddrive is willing to test this, please
> > contact me, I'll give you a patch.
>
> I'm in.
> i815ep (tusl2-c mainboard) + maxtor 80GB udma 133.
>
> I'm wondering how you can do that though... Would you
> explain, please ?
The ich2/3 use a 133 MHz base clock for IDE timing. And have a divisor
settable, they divide by three to get 50 MHz base clock for UDMA100
(it's 16-bit), and can divide by two to get 66 and hence UDMA133.
However that value (division by 2 with 133 MHz clock) is marked as
'reserved' in the specs.
In the end it may or may not work. I'm very curious, though.
VERY untested patch attached.
--
Vojtech Pavlik
SuSE Labs
[-- Attachment #2: piix-test.diff --]
[-- Type: text/plain, Size: 3902 bytes --]
diff -urN linux-2.5.7/drivers/ide/piix.c linux-2.5.7-piix/drivers/ide/piix.c
--- linux-2.5.7/drivers/ide/piix.c Fri Mar 29 16:01:51 2002
+++ linux-2.5.7-piix/drivers/ide/piix.c Sat Mar 30 14:08:31 2002
@@ -1,5 +1,5 @@
/*
- * $Id: piix.c,v 1.2 2002/03/13 22:50:43 vojtech Exp $
+ * $Id: piix.c,v 1.2-test133 2002/03/13 22:50:43 vojtech Exp $
*
* Copyright (c) 2000-2002 Vojtech Pavlik
*
@@ -62,7 +62,7 @@
#define PIIX_UDMA_33 0x01
#define PIIX_UDMA_66 0x02
#define PIIX_UDMA_V66 0x03
-#define PIIX_UDMA_100 0x04
+#define PIIX_UDMA_133 0x05
#define PIIX_NO_SITRE 0x08 /* Chip doesn't have separate slave timing */
#define PIIX_PINGPONG 0x10 /* Enable ping-pong buffers */
#define PIIX_VICTORY 0x20 /* Efar Victory66 has a different UDMA setup */
@@ -77,10 +77,10 @@
unsigned short id;
unsigned char flags;
} piix_ide_chips[] = {
- { PCI_DEVICE_ID_INTEL_82801CA_11, PIIX_UDMA_100 | PIIX_PINGPONG }, /* Intel 82801CA ICH3 */
- { PCI_DEVICE_ID_INTEL_82801CA_10, PIIX_UDMA_100 | PIIX_PINGPONG }, /* Intel 82801CAM ICH3-M */
- { PCI_DEVICE_ID_INTEL_82801BA_9, PIIX_UDMA_100 | PIIX_PINGPONG }, /* Intel 82801BA ICH2 */
- { PCI_DEVICE_ID_INTEL_82801BA_8, PIIX_UDMA_100 | PIIX_PINGPONG }, /* Intel 82801BAM ICH2-M */
+ { PCI_DEVICE_ID_INTEL_82801CA_11, PIIX_UDMA_133 | PIIX_PINGPONG }, /* Intel 82801CA ICH3 */
+ { PCI_DEVICE_ID_INTEL_82801CA_10, PIIX_UDMA_133 | PIIX_PINGPONG }, /* Intel 82801CAM ICH3-M */
+ { PCI_DEVICE_ID_INTEL_82801BA_9, PIIX_UDMA_133 | PIIX_PINGPONG }, /* Intel 82801BA ICH2 */
+ { PCI_DEVICE_ID_INTEL_82801BA_8, PIIX_UDMA_133 | PIIX_PINGPONG }, /* Intel 82801BAM ICH2-M */
{ PCI_DEVICE_ID_INTEL_82801AB_1, PIIX_UDMA_33 | PIIX_PINGPONG }, /* Intel 82801AB ICH0 */
{ PCI_DEVICE_ID_INTEL_82801AA_1, PIIX_UDMA_66 | PIIX_PINGPONG }, /* Intel 82801AA ICH */
{ PCI_DEVICE_ID_INTEL_82372FB_1, PIIX_UDMA_66 }, /* Intel 82372FB PIIX5 */
@@ -97,7 +97,7 @@
static unsigned int piix_80w;
static unsigned int piix_clock;
-static char *piix_dma[] = { "MWDMA16", "UDMA33", "UDMA66", "UDMA66", "UDMA100" };
+static char *piix_dma[] = { "MWDMA16", "UDMA33", "UDMA66", "UDMA66", "UDMA100", "UDMA133" };
/*
* PIIX/ICH /proc entry.
@@ -128,7 +128,7 @@
piix_print("----------PIIX BusMastering IDE Configuration---------------");
- piix_print("Driver Version: 1.2");
+ piix_print("Driver Version: 1.2-test133");
piix_print("South Bridge: %s", bmide_dev->name);
pci_read_config_byte(dev, PCI_REVISION_ID, &t);
@@ -199,7 +199,7 @@
if (~piix_config->flags & PIIX_VICTORY) {
if ((piix_config->flags & PIIX_UDMA) >= PIIX_UDMA_66 && (u & (1 << i))) umul = 2;
- if ((piix_config->flags & PIIX_UDMA) >= PIIX_UDMA_100 && (u & ((1 << i) + 12))) umul = 1;
+ if ((piix_config->flags & PIIX_UDMA) >= PIIX_UDMA_133 && (u & (1 << (i + 12)))) umul = 1;
udma[i] = (4 - ((e >> (i << 2)) & 3)) * umul;
} else udma[i] = (8 - ((e >> (i << 2)) & 7)) * 2;
@@ -388,7 +388,7 @@
(piix_config->flags & PIIX_NODMA ? 0 : (XFER_SWDMA | XFER_MWDMA |
(piix_config->flags & PIIX_UDMA ? XFER_UDMA : 0) |
(w80 && (piix_config->flags & PIIX_UDMA) >= PIIX_UDMA_66 ? XFER_UDMA_66 : 0) |
- (w80 && (piix_config->flags & PIIX_UDMA) >= PIIX_UDMA_100 ? XFER_UDMA_100 : 0))));
+ (w80 && (piix_config->flags & PIIX_UDMA) >= PIIX_UDMA_133 ? (XFER_UDMA_100 | XFER_UDMA_133) : 0))));
piix_set_drive(drive, speed);
@@ -458,7 +458,7 @@
switch (piix_config->flags & PIIX_UDMA) {
case PIIX_UDMA_66:
- case PIIX_UDMA_100:
+ case PIIX_UDMA_133:
pci_read_config_dword(dev, PIIX_IDECFG, &u);
piix_80w = ((u & 0x30) ? 1 : 0) | ((u & 0xc0) ? 2 : 0);
break;
prev parent reply other threads:[~2002-03-30 13:09 UTC|newest]
Thread overview: 3+ messages / expand[flat|nested] mbox.gz Atom feed top
2002-03-30 11:42 Anyone with an ICH2 or ICH3 Intel southbridge and UDMA133 harddrive willing to test? Vojtech Pavlik
2002-03-30 12:57 ` François Cami
2002-03-30 13:09 ` Vojtech Pavlik [this message]
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20020330140910.A731@ucw.cz \
--to=vojtech@suse.cz \
--cc=linux-kernel@vger.kernel.org \
--cc=martin@dalecki.de \
--cc=stilgar2k@wanadoo.fr \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox