* ide-convert-9 oops on boot
@ 2002-05-04 2:24 J.A. Magallon
2002-05-04 8:45 ` Heinz Diehl
2002-05-05 1:08 ` ide-convert-[89] oops (decoded) " J.A. Magallon
0 siblings, 2 replies; 3+ messages in thread
From: J.A. Magallon @ 2002-05-04 2:24 UTC (permalink / raw)
To: Lista Linux-Kernel; +Cc: Andre Hedrick
Hi.
Just patched pre8 with ide-convert-9, and system hangs on boot:
PIIX4: IDE controller on PCI bus 00 dev 39
PIIX4: chipset revision 1
PIIX4: not 100% native mode: will probe irqs later
ide0: BM-DMA at 0xffa0-0xffa7, BIOS settings: hda:DMA, hdb:DMA
ide1: BM-DMA at 0xffa8-0xffaf, BIOS settings: hdc:DMA, hdd:pio
hda: Conner Peripherals 1080MB - CFS1081A, ATA DISK drive
hdb: CREATIVE CD5230E, ATAPI CD/DVD-ROM drive
hdc: YAMAHA CRW8424E, ATAPI CD/DVD-ROM drive
hdd: IOMEGA ZIP 250 ATAPI, ATAPI FLOPPY drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
ide1 at 0x170-0x177,0x376 on irq 15
<=======0 OOPS here, just got hung...
<usual output follows >
hda: 2114180 sectors (1082 MB), CHS=524/64/63, DMA
ide-cd: passing drive hdb to ide-scsi emulation.
ide-cd: passing drive hdc to ide-scsi emulation.
ide-floppy driver 0.99.newide
If it is not a known problem, and anyone needs more info I can write
down the hex and decode it.
TIA
werewolf:/proc/ide# lspci
00:00.0 Host bridge: Intel Corp. 440GX - 82443GX Host bridge
00:01.0 PCI bridge: Intel Corp. 440GX - 82443GX AGP bridge
00:07.0 ISA bridge: Intel Corp. 82371AB/EB/MB PIIX4 ISA (rev 02)
00:07.1 IDE interface: Intel Corp. 82371AB/EB/MB PIIX4 IDE (rev 01)
00:07.2 USB Controller: Intel Corp. 82371AB/EB/MB PIIX4 USB (rev 01)
00:07.3 Bridge: Intel Corp. 82371AB/EB/MB PIIX4 ACPI (rev 02)
00:0d.0 Multimedia video controller: Brooktree Corporation Bt878 Video Capture (rev 11)
00:0d.1 Multimedia controller: Brooktree Corporation Bt878 Audio Capture (rev 11)
00:0e.0 SCSI storage controller: Adaptec AHA-2940U2/U2W / 7890/7891 (rev 01)
00:0f.0 Multimedia audio controller: Creative Labs SB Live! EMU10k1 (rev 06)
00:0f.1 Input device controller: Creative Labs SB Live! MIDI/Game Port (rev 06)
00:10.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8029(AS)
00:12.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8139/8139C (rev 10)
01:00.0 VGA compatible controller: nVidia Corporation NV11 [GeForce2 MX] (rev b2)
werewolf:/proc/ide# cat piix
Intel PIIX4 Ultra 33 Chipset.
--------------- Primary Channel ---------------- Secondary Channel -------------
enabled enabled
--------------- drive0 --------- drive1 -------- drive0 ---------- drive1 ------
DMA enabled: yes yes yes no
UDMA enabled: no no no no
UDMA enabled: X X X X
UDMA
DMA
PIO
--
J.A. Magallon # Let the source be with you...
mailto:jamagallon@able.es
Mandrake Linux release 8.3 (Cooker) for i586
Linux werewolf 2.4.19-pre7-jam9 #2 SMP mié may 1 12:09:38 CEST 2002 i686
^ permalink raw reply [flat|nested] 3+ messages in thread* Re: ide-convert-9 oops on boot
2002-05-04 2:24 ide-convert-9 oops on boot J.A. Magallon
@ 2002-05-04 8:45 ` Heinz Diehl
2002-05-05 1:08 ` ide-convert-[89] oops (decoded) " J.A. Magallon
1 sibling, 0 replies; 3+ messages in thread
From: Heinz Diehl @ 2002-05-04 8:45 UTC (permalink / raw)
To: linux-kernel; +Cc: jamagallon, andre
On Sat May 04 2002, J.A. Magallon wrote:
> Just patched pre8 with ide-convert-9, and system hangs on boot:
Exactly the same thing here. You're not alone ;)
[....]
Journalled Block Device driver loaded
Real Time Clock Driver v1.10e
Uniform Multi-Platform E-IDE driver Revision: 6.31
ide: Assuming 33MHz system bus speed for PIO modes
VP_IDE: IDE controller on PCI bus 00 dev 39
VP_IDE: chipset revision 6
VP_IDE: not 100% native mode: will probe irqs later
VP_IDE: VIA vt82c586b (rev 41) IDE UDMA33 controller on pci00:07.1
ide0: BM-DMA at 0xe000-0xe007, BIOS settings: hda:DMA, hdb:DMA
ide1: BM-DMA at 0xe008-0xe00f, BIOS settings: hdc:DMA, hdd:DMA
hda: IBM-DHEA-36481, ATA DISK drive
hdb: Conner Peripherals 1275MB - CFS1275A, ATA DISK drive
hdc: CD-540E, ATAPI CD/DVD-ROM drive
hdd: CD-W54E, ATAPI CD/DVD-ROM drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
ide1 at 0x170-0x177,0x376 on irq 15
hda: 12692736 sectors (6499 MB) w/472KiB Cache, CHS=790/255/63, UDMA(33)
hdb: 2496876 sectors (1278 MB) w/64KiB Cache, CHS=619/64/63, DMA
[....]
chiara:~ # lspci
00:00.0 Host bridge: VIA Technologies, Inc. VT82C598 [Apollo MVP3] (rev 04)
00:01.0 PCI bridge: VIA Technologies, Inc. VT82C598 [Apollo MVP3 AGP]
00:07.0 ISA bridge: VIA Technologies, Inc. VT82C586/A/B PCI-to-ISA [Apollo
VP] (rev 41)
00:07.1 IDE interface: VIA Technologies, Inc. VT82C586 IDE [Apollo] (rev 06)
00:07.3 Host bridge: VIA Technologies, Inc. VT82C586B ACPI (rev 10)
00:11.0 VGA compatible controller: S3 Inc. ViRGE/DX or /GX (rev 01)
chiara:~ cat /proc/ide/via
----------VIA BusMastering IDE Configuration----------------
Driver Version: 3.34
South Bridge: VIA vt82c586b
Revision: ISA 0x41 IDE 0x6
Highest DMA rate: UDMA33
BM-DMA base: 0xe000
PCI clock: 33.3MHz
Master Read Cycle IRDY: 1ws
Master Write Cycle IRDY: 1ws
BM IDE Status Register Read Retry: yes
Max DRDY Pulse Width: No limit
-----------------------Primary IDE-------Secondary IDE------
Read DMA FIFO flush: yes yes
End Sector FIFO flush: no no
Prefetch Buffer: yes yes
Post Write Buffer: yes no
Enabled: yes yes
Simplex only: no no
Cable Type: 40w 40w
-------------------drive0----drive1----drive2----drive3-----
Transfer Mode: UDMA DMA UDMA DMA
Address Setup: 30ns 30ns 30ns 30ns
Cmd Active: 90ns 90ns 90ns 90ns
Cmd Recovery: 30ns 30ns 30ns 30ns
Data Active: 90ns 90ns 90ns 90ns
Data Recovery: 30ns 30ns 30ns 30ns
Cycle Time: 60ns 120ns 60ns 120ns
Transfer Rate: 33.3MB/s 16.6MB/s 33.3MB/s 16.6MB/s
--
# Heinz Diehl, 68259 Mannheim, Germany
^ permalink raw reply [flat|nested] 3+ messages in thread
* ide-convert-[89] oops (decoded) on boot
2002-05-04 2:24 ide-convert-9 oops on boot J.A. Magallon
2002-05-04 8:45 ` Heinz Diehl
@ 2002-05-05 1:08 ` J.A. Magallon
1 sibling, 0 replies; 3+ messages in thread
From: J.A. Magallon @ 2002-05-05 1:08 UTC (permalink / raw)
To: Lista Linux-Kernel; +Cc: Andre Hedrick
On 2002.05.04 J.A. Magallon wrote:
>Hi.
>
>Just patched pre8 with ide-convert-9, and system hangs on boot:
>
>PIIX4: IDE controller on PCI bus 00 dev 39
>PIIX4: chipset revision 1
>PIIX4: not 100% native mode: will probe irqs later
> ide0: BM-DMA at 0xffa0-0xffa7, BIOS settings: hda:DMA, hdb:DMA
> ide1: BM-DMA at 0xffa8-0xffaf, BIOS settings: hdc:DMA, hdd:pio
>hda: Conner Peripherals 1080MB - CFS1081A, ATA DISK drive
>hdb: CREATIVE CD5230E, ATAPI CD/DVD-ROM drive
>hdc: YAMAHA CRW8424E, ATAPI CD/DVD-ROM drive
>hdd: IOMEGA ZIP 250 ATAPI, ATAPI FLOPPY drive
>ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
>ide1 at 0x170-0x177,0x376 on irq 15
>
><=======0 OOPS here, just got hung...
> <usual output follows >
>hda: 2114180 sectors (1082 MB), CHS=524/64/63, DMA
>ide-cd: passing drive hdb to ide-scsi emulation.
>ide-cd: passing drive hdc to ide-scsi emulation.
>ide-floppy driver 0.99.newide
convert.8 also hangs. convert.6 worked in my latest 2.4.19-pre7-jam6.
Now I'm building -pre8-jam1, and the jump from convert.6 to convert.9
does not work. Bott is fine without the patch, with included ide.
Only option yet to be tested is convert.7...
Decoded oops:
ksymoops 2.4.5 on i686 2.4.19-pre7-jam9. Options used
-V (default)
-k /proc/ksyms (default)
-l /proc/modules (default)
-o /lib/modules/2.4.19-pre8-jam1/ (specified)
-m /boot/System.map-2.4.19-pre8-jam1 (specified)
[ton of warnings about ksyms mismatchs...]
Unable to handle kernel NULL pointer derefernce at virtual address 00000040
c01cd2d7
*pde = 000000000
Oops: 0000
CPU: 1
EIP: 0010:[<c01cd2d7>] Not tainted
Using defaults from ksymoops -t elf32-i386 -a i386
EFLAGS: 00010292
eax: 00000000 ebx: c0376f40 ecx: c01d4010 edx: 00000020
esi: c0376f84 edi: 00000007 ebp: 0008e000 esp: c15b5f38
ds: 0018 es: 0018 ss: 0018
Process swapper (pid: 1, stackpage=c15b5000)
c0288031 c0165de1 dfe549a0 00000000 0000004c c02ad1f0 00000001 c01cd2b0
c0376f84 c02ad2a0 0008e000 c01cc19f 00000007 c0376f84 c0376f40 c0376f84
00000001 c0105000 c01d4064 c0376f84 c02ad2a0 00000001 00000000 c0376f40
[<c0165de1>]
[<c01cd2b0>]
[<c01cc19f>]
[<c0105000>]
[<c01d4064>]
[<c010508b>]
[<c0105000>]
[<c010758d>]
Code: 8b 40 40 89 44 24 18 8b ab 2c 03 00 0f b6 86 c4 00 00 00
>>EIP; c01cd2d7 <ide_dmaproc+27/370> <=====
>>ebx; c0376f40 <ide_hwifs+0/2238>
>>ecx; c01d4010 <idedisk_init+0/130>
>>esi; c0376f84 <ide_hwifs+44/2238>
>>ebp; 0008e000 Before first symbol
>>esp; c15b5f38 <_end+12305e4/204a86ac>
Code; c01cd2d7 <ide_dmaproc+27/370>
00000000 <_EIP>:
Code; c01cd2d7 <ide_dmaproc+27/370> <=====
0: 8b 40 40 mov 0x40(%eax),%eax <=====
Code; c01cd2da <ide_dmaproc+2a/370>
3: 89 44 24 18 mov %eax,0x18(%esp,1)
Code; c01cd2de <ide_dmaproc+2e/370>
7: 8b ab 2c 03 00 0f mov 0xf00032c(%ebx),%ebp
Code; c01cd2e4 <ide_dmaproc+34/370>
d: b6 86 mov $0x86,%dh
Code; c01cd2e6 <ide_dmaproc+36/370>
f: c4 00 les (%eax),%eax
<0> Kernel panic: Attempted to kill init !
1211 warnings issued. Results may not be reliable.
Hope this helps...
--
J.A. Magallon # Let the source be with you...
mailto:jamagallon@able.es
Mandrake Linux release 8.3 (Cooker) for i586
Linux werewolf 2.4.19-pre8-jam1 #3 SMP dom may 5 02:28:08 CEST 2002 i686
^ permalink raw reply [flat|nested] 3+ messages in thread
end of thread, other threads:[~2002-05-05 1:08 UTC | newest]
Thread overview: 3+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
2002-05-04 2:24 ide-convert-9 oops on boot J.A. Magallon
2002-05-04 8:45 ` Heinz Diehl
2002-05-05 1:08 ` ide-convert-[89] oops (decoded) " J.A. Magallon
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox