Re: linnux 2.4.19-rc1 i845e ide not detected. dma doesn't work

Re: linnux 2.4.19-rc1 i845e ide not detected. dma doesn't work

[Anthony Spinillo]

Andre,

I just fired up 2.5.25. DMA was enabled upon boot on 
my DVD drive and burner. (no IDE hard drive - SCSI)

2.4.19pre10ac2 works for me also.

I also turned in a Bugzilla for Limbo the new RedHat
beta.

Intel 845GBVL motherboard - 845G chipset.

Thanks!

Tony

>Does it work in 2.5 ?


On Thu, 4 Jul 2002, Nick Evgeniev wrote:

>> Well, anyway, 2.4.19-pre10-ac2 works for me :)

-- 
Get your free email from www.linuxmail.org 


Powered by Outblaze

linnux 2.4.19-rc1 i845e ide not detected. dma doesn't work

[Nick Evgeniev]

Hi,

I wrote here about my problems with promise pdc controller in smp
configuration, and I was told that I'm using bad hardware (VIA chipset)
and blah-blah-blah...

Well, I've changed hardware to UP P4 box based on i845e chipset...
Now I've got the following messages on kernel boot, and of cause no DMA
on ide channels (even with hdparm):


Uniform Multi-Platform E-IDE driver Revision: 6.31
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
ICH4: IDE controller on PCI bus 00 dev f9
PCI: Device 00:1f.1 not available because of resource collisions
ICH4: (ide_setup_pci_device:) Could not enable device.

here is lspci output:

00:1f.1 IDE interface: Intel Corp.: Unknown device 24cb (rev 01) (prog-if 8a
+[Master SecP PriP])
        Subsystem: Micro-star International Co Ltd: Unknown device 5661
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
+Stepping- SERR- FastB2B-
        Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
+<TAbort- <MAbort- >SERR- <PERR-
        Latency: 0
        Interrupt: pin A routed to IRQ 18
        Region 0: I/O ports at <unassigned> [size=8]
        Region 1: I/O ports at <unassigned> [size=4]
        Region 2: I/O ports at <unassigned> [size=8]
        Region 3: I/O ports at <unassigned> [size=4]
        Region 4: I/O ports at fc00 [size=16]
        Region 5: Memory at 20000000 (32-bit, non-prefetchable) [size=1K]

What should I do with my hardware? Through it away? round and around?!

Re: linnux 2.4.19-rc1 i845e ide not detected. dma doesn't work

[Alan Cox]

Complain to your BIOS vendor

A workaround for this BIOS flaw will be in the -ac tree in a week or so

Re: linnux 2.4.19-rc1 i845e ide not detected. dma doesn't work

[Nick Evgeniev]

Hi,

    Why are you so assure? It's "msi 845e Max" with LAN on-board mb with
_latest_ BIOS installed....
Just FYI 2.4.18 was even unable to run eepro100 driver on it while intels
e100 driver was working perfectly.

----- Original Message -----
From: "Alan Cox" <alan@lxorguk.ukuu.org.uk>
To: "Nick Evgeniev" <nick@octet.spb.ru>
Cc: <linux-kernel@vger.kernel.org>
Sent: Saturday, June 29, 2002 6:32 AM
Subject: Re: linnux 2.4.19-rc1 i845e ide not detected. dma doesn't work


> Complain to your BIOS vendor
>
> A workaround for this BIOS flaw will be in the -ac tree in a week or so
>
>

Re: linnux 2.4.19-rc1 i845e ide not detected. dma doesn't work

[Dave Jones]

On Mon, Jul 01, 2002 at 03:49:43PM +0400, Nick Evgeniev wrote:

 >     Why are you so assure? It's "msi 845e Max" with LAN on-board mb with
 > _latest_ BIOS installed....
 > Just FYI 2.4.18 was even unable to run eepro100 driver on it while intels
 > e100 driver was working perfectly.

Could this be related to the pci id clash I pointed out last week?
That id was for an intel IDE device iirc.

(Recap: Two id's don't tally between 2.4/2.5)

        Dave

-- 
| Dave Jones.        http://www.codemonkey.org.uk
| SuSE Labs

Re: linnux 2.4.19-rc1 i845e ide not detected. dma doesn't work

[Andre Hedrick]

No it has everything to do with determining if the HBA is in compatablity
or native mode and if the device is properly enabled.

On Wed, 3 Jul 2002, Dave Jones wrote:

> On Mon, Jul 01, 2002 at 03:49:43PM +0400, Nick Evgeniev wrote:
> 
>  >     Why are you so assure? It's "msi 845e Max" with LAN on-board mb with
>  > _latest_ BIOS installed....
>  > Just FYI 2.4.18 was even unable to run eepro100 driver on it while intels
>  > e100 driver was working perfectly.
> 
> Could this be related to the pci id clash I pointed out last week?
> That id was for an intel IDE device iirc.
> 
> (Recap: Two id's don't tally between 2.4/2.5)
> 
>         Dave
> 
> -- 
> | Dave Jones.        http://www.codemonkey.org.uk
> | SuSE Labs
> -
> To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
> the body of a message to majordomo@vger.kernel.org
> More majordomo info at  http://vger.kernel.org/majordomo-info.html
> Please read the FAQ at  http://www.tux.org/lkml/
> 

Andre Hedrick
LAD Storage Consulting Group

Re: linnux 2.4.19-rc1 i845e ide not detected. dma doesn't work

[Nick Evgeniev]

Well, anyway, 2.4.19-pre10-ac2 works for me :)

> No it has everything to do with determining if the HBA is in compatablity
> or native mode and if the device is properly enabled.
>
> On Wed, 3 Jul 2002, Dave Jones wrote:
>
> > On Mon, Jul 01, 2002 at 03:49:43PM +0400, Nick Evgeniev wrote:
> >
> >  >     Why are you so assure? It's "msi 845e Max" with LAN on-board mb
with
> >  > _latest_ BIOS installed....
> >  > Just FYI 2.4.18 was even unable to run eepro100 driver on it while
intels
> >  > e100 driver was working perfectly.
> >
> > Could this be related to the pci id clash I pointed out last week?
> > That id was for an intel IDE device iirc.
> >
> > (Recap: Two id's don't tally between 2.4/2.5)
> >
> >         Dave
> >
> > --
> > | Dave Jones.        http://www.codemonkey.org.uk
> > | SuSE Labs
> > -
> > To unsubscribe from this list: send the line "unsubscribe linux-kernel"
in
> > the body of a message to majordomo@vger.kernel.org
> > More majordomo info at  http://vger.kernel.org/majordomo-info.html
> > Please read the FAQ at  http://www.tux.org/lkml/
> >
>
> Andre Hedrick
> LAD Storage Consulting Group
>
> -
> To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
> the body of a message to majordomo@vger.kernel.org
> More majordomo info at  http://vger.kernel.org/majordomo-info.html
> Please read the FAQ at  http://www.tux.org/lkml/
>

Re: linnux 2.4.19-rc1 i845e ide not detected. dma doesn't work

[Andre Hedrick]

Does it work in 2.5 ?


On Thu, 4 Jul 2002, Nick Evgeniev wrote:

> Well, anyway, 2.4.19-pre10-ac2 works for me :)
> 
> > No it has everything to do with determining if the HBA is in compatablity
> > or native mode and if the device is properly enabled.
> >
> > On Wed, 3 Jul 2002, Dave Jones wrote:
> >
> > > On Mon, Jul 01, 2002 at 03:49:43PM +0400, Nick Evgeniev wrote:
> > >
> > >  >     Why are you so assure? It's "msi 845e Max" with LAN on-board mb
> with
> > >  > _latest_ BIOS installed....
> > >  > Just FYI 2.4.18 was even unable to run eepro100 driver on it while
> intels
> > >  > e100 driver was working perfectly.
> > >
> > > Could this be related to the pci id clash I pointed out last week?
> > > That id was for an intel IDE device iirc.
> > >
> > > (Recap: Two id's don't tally between 2.4/2.5)
> > >
> > >         Dave
> > >
> > > --
> > > | Dave Jones.        http://www.codemonkey.org.uk
> > > | SuSE Labs
> > > -
> > > To unsubscribe from this list: send the line "unsubscribe linux-kernel"
> in
> > > the body of a message to majordomo@vger.kernel.org
> > > More majordomo info at  http://vger.kernel.org/majordomo-info.html
> > > Please read the FAQ at  http://www.tux.org/lkml/
> > >
> >
> > Andre Hedrick
> > LAD Storage Consulting Group
> >
> > -
> > To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
> > the body of a message to majordomo@vger.kernel.org
> > More majordomo info at  http://vger.kernel.org/majordomo-info.html
> > Please read the FAQ at  http://www.tux.org/lkml/
> >
> 

Andre Hedrick
LAD Storage Consulting Group

Re: linnux 2.4.19-rc1 i845e ide not detected. dma doesn't work

[Nick Evgeniev]

I don't know. Actually, I'm trying to setup "production" environment :)) &
i845e (or i845pe) is the only one solution (I don't want to try via+promise
anymore)

----- Original Message -----
From: "Andre Hedrick" <andre@linux-ide.org>
To: "Nick Evgeniev" <nick@octet.spb.ru>
Cc: "Dave Jones" <davej@suse.de>; "Alan Cox" <alan@lxorguk.ukuu.org.uk>;
<linux-kernel@vger.kernel.org>
Sent: Saturday, July 06, 2002 4:25 AM
Subject: Re: linnux 2.4.19-rc1 i845e ide not detected. dma doesn't work


>
> Does it work in 2.5 ?
>
>
> On Thu, 4 Jul 2002, Nick Evgeniev wrote:
>
> > Well, anyway, 2.4.19-pre10-ac2 works for me :)
> >
> > > No it has everything to do with determining if the HBA is in
compatablity
> > > or native mode and if the device is properly enabled.
> > >
> > > On Wed, 3 Jul 2002, Dave Jones wrote:
> > >
> > > > On Mon, Jul 01, 2002 at 03:49:43PM +0400, Nick Evgeniev wrote:
> > > >
> > > >  >     Why are you so assure? It's "msi 845e Max" with LAN on-board
mb
> > with
> > > >  > _latest_ BIOS installed....
> > > >  > Just FYI 2.4.18 was even unable to run eepro100 driver on it
while
> > intels
> > > >  > e100 driver was working perfectly.
> > > >
> > > > Could this be related to the pci id clash I pointed out last week?
> > > > That id was for an intel IDE device iirc.
> > > >
> > > > (Recap: Two id's don't tally between 2.4/2.5)
> > > >
> > > >         Dave
> > > >
> > > > --
> > > > | Dave Jones.        http://www.codemonkey.org.uk
> > > > | SuSE Labs
> > > > -
> > > > To unsubscribe from this list: send the line "unsubscribe
linux-kernel"
> > in
> > > > the body of a message to majordomo@vger.kernel.org
> > > > More majordomo info at  http://vger.kernel.org/majordomo-info.html
> > > > Please read the FAQ at  http://www.tux.org/lkml/
> > > >
> > >
> > > Andre Hedrick
> > > LAD Storage Consulting Group
> > >
> > > -
> > > To unsubscribe from this list: send the line "unsubscribe
linux-kernel" in
> > > the body of a message to majordomo@vger.kernel.org
> > > More majordomo info at  http://vger.kernel.org/majordomo-info.html
> > > Please read the FAQ at  http://www.tux.org/lkml/
> > >
> >
>
> Andre Hedrick
> LAD Storage Consulting Group
>
>