* 2.4.20-pre3 boot hang
@ 2002-08-18 15:31 Klaus Dittrich
2002-08-18 18:06 ` Markus Plail
` (2 more replies)
0 siblings, 3 replies; 13+ messages in thread
From: Klaus Dittrich @ 2002-08-18 15:31 UTC (permalink / raw)
To: linux mailing-list
SMP, P-III, Intel-BX
booting Linux 2.4.20-pre3 stops after
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
--
Regards Klaus
^ permalink raw reply [flat|nested] 13+ messages in thread
* Re: 2.4.20-pre3 boot hang
2002-08-18 15:31 2.4.20-pre3 boot hang Klaus Dittrich
@ 2002-08-18 18:06 ` Markus Plail
2002-08-18 18:22 ` Alan Cox
2002-08-18 18:42 ` Erik Andersen
2002-08-19 11:13 ` Mauricio Pretto
2 siblings, 1 reply; 13+ messages in thread
From: Markus Plail @ 2002-08-18 18:06 UTC (permalink / raw)
To: linux mailing-list
Hi Klaus!
* Klaus Dittrich writes:
>SMP, P-III, Intel-BX
>booting Linux 2.4.20-pre3 stops after
>Linux NET4.0 for Linux 2.4
>Based upon Swansea University Computer Society NET3.039
>Initializing RT netlink socket
Same here.
Apart from that, the latest ac series oopses when I try to mount a CD
in a drive driven by ide-scsi emulation. And the IDE performance was
quite a bit worse than 2.4.18. Sorry for not being able to make more
concrete statements, just wanted to mention it.
regards
Markus
Athlon XP1800+, ECS K7VZA, single processor, APIC
Gnu C 2.95.3
Gnu make 3.79.1
binutils 2.11.2
util-linux 2.11m
mount 2.11m
modutils 2.4.16
e2fsprogs 1.25
reiserfsprogs 3.x.0j
Linux C Library 2.2.4
Dynamic linker (ldd) 2.2.4
Procps 2.0.7
Net-tools 1.60
Kbd 1.06
Sh-utils 2.0
00:00.0 Host bridge: Silicon Integrated Systems [SiS] 735 Host (rev 01)
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66Mhz- UDF-
FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR-
<PERR- Latency: 32 Region 0: Memory at d0000000 (32-bit,
non-prefetchable) [size=128M] Capabilities: [c0] AGP version 2.0
Status: RQ=31 SBA+ 64bit- FW- Rate=x1,x2
Command: RQ=0 SBA- AGP- 64bit- FW- Rate=<none>
00:01.0 PCI bridge: Silicon Integrated Systems [SiS] 5591/5592 AGP
(prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR+ FastB2B- Status: Cap- 66Mhz- UDF-
FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR-
<PERR- Latency: 64 Bus: primary=00, secondary=01,
subordinate=01, sec-latency=64 I/O behind bridge:
0000f000-00000fff Memory behind bridge: cde00000-cfefffff
Prefetchable memory behind bridge: bdc00000-cdcfffff BridgeCtl:
Parity- SERR+ NoISA- VGA+ MAbort- >Reset- FastB2B-
00:02.0 ISA bridge: Silicon Integrated Systems [SiS] 85C503/5513
Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B- Status: Cap- 66Mhz- UDF-
FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR-
<PERR- Latency: 0
00:02.2 USB Controller: Silicon Integrated Systems [SiS] 7001 (rev 07)
(prog-if 10 [OHCI])
Subsystem: Elitegroup Computer Systems: Unknown device 0a14
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop-
ParErr- Stepping- SERR+ FastB2B- Status: Cap- 66Mhz- UDF-
FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR-
<PERR- Latency: 64 (20000ns max), cache line size 08 Interrupt:
pin D routed to IRQ 5 Region 0: Memory at cfffc000 (32-bit,
non-prefetchable) [size=4K]
00:02.3 USB Controller: Silicon Integrated Systems [SiS] 7001 (rev 07)
(prog-if 10 [OHCI])
Subsystem: Elitegroup Computer Systems: Unknown device 0a14
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop-
ParErr- Stepping- SERR+ FastB2B- Status: Cap- 66Mhz- UDF-
FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR-
<PERR- Latency: 64 (20000ns max), cache line size 08 Interrupt:
pin A routed to IRQ 10 Region 0: Memory at cfffd000 (32-bit,
non-prefetchable) [size=4K]
00:02.5 IDE interface: Silicon Integrated Systems [SiS] 5513 [IDE] (rev
d0) (prog-if 80 [Master])
Subsystem: Silicon Integrated Systems [SiS] SiS5513 EIDE
Controller (A,B step) Control: I/O+ Mem- BusMaster+ SpecCycle-
MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap-
66Mhz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- Latency: 128 Region 4: I/O ports at ff00
[size=16]
00:03.0 Ethernet controller: Silicon Integrated Systems [SiS] SiS900
10/100 Ethernet (rev 90)
Subsystem: Elitegroup Computer Systems: Unknown device 0a14
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR+ FastB2B- Status: Cap+ 66Mhz- UDF-
FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR-
<PERR- Latency: 64 (13000ns min, 2750ns max) Interrupt: pin A
routed to IRQ 12 Region 0: I/O ports at d400 [size=256] Region
1: Memory at cfffb000 (32-bit, non-prefetchable) [size=4K]
Expansion ROM at cffc0000 [disabled] [size=128K] Capabilities:
[40] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
PME(D0+,D1+,D2+,D3hot+,D3cold+) Status: D0 PME-Enable-
DSel=0 DScale=0 PME-
00:09.0 SCSI storage controller: LSI Logic / Symbios Logic (formerly
NCR) 53c875 (rev 26)
Subsystem: LSI Logic / Symbios Logic (formerly NCR): Unknown
device 1000 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+
VGASnoop- ParErr+ Stepping- SERR+ FastB2B- Status: Cap+ 66Mhz-
UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort-
>SERR- <PERR- Latency: 134 (4250ns min, 16000ns max), cache line
size 08 Interrupt: pin A routed to IRQ 11 Region 0: I/O ports at
d800 [size=256] Region 1: Memory at cfffff00 (32-bit,
non-prefetchable) [size=256] Region 2: Memory at cfffe000
(32-bit, non-prefetchable) [size=4K] Expansion ROM at cffe0000
[disabled] [size=64K] Capabilities: [40] Power Management
version 1
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 PME-Enable-
DSel=0 DScale=0 PME-
00:0b.0 Multimedia audio controller: Creative Labs SB Live! EMU10k1 (rev07)
Subsystem: Creative Labs: Unknown device 8061 Control: I/O+ Mem-
BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+
FastB2B- Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium
>TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 64 (500ns min,
5000ns max) Interrupt: pin A routed to IRQ 11 Region 0: I/O
ports at d000 [size=32] Capabilities: [dc] Power Management
version 1
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 PME-Enable-
DSel=0 DScale=0 PME-
00:0b.1 Input device controller: Creative Labs SB Live! (rev 07)
Subsystem: Creative Labs Gameport Joystick Control: I/O+ Mem-
BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+
FastB2B- Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium
>TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 64 Region 0:
I/O ports at dc00 [size=8] Capabilities: [dc] Power Management
version 1
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 PME-Enable-
DSel=0 DScale=0 PME-
00:0d.0 Multimedia video controller: Brooktree Corporation Bt878 (rev11)
Subsystem: Hauppauge computer works Inc. WinTV/GO Control: I/O-
Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping-
SERR+ FastB2B- Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr-
DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency:
64 (4000ns min, 10000ns max) Interrupt: pin A routed to IRQ 5
Region 0: Memory at cddfe000 (32-bit, prefetchable) [size=4K]
Capabilities: [44] Vital Product Data Capabilities: [4c] Power
Management version 2
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 PME-Enable-
DSel=0 DScale=0 PME-
00:0d.1 Multimedia controller: Brooktree Corporation Bt878 (rev 11)
Subsystem: Hauppauge computer works Inc. WinTV/GO Control: I/O-
Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping-
SERR+ FastB2B- Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr-
DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency:
64 (1000ns min, 63750ns max) Interrupt: pin A routed to IRQ 5
Region 0: Memory at cddff000 (32-bit, prefetchable) [size=4K]
Capabilities: [44] Vital Product Data Capabilities: [4c] Power
Management version 2
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 PME-Enable-
DSel=0 DScale=0 PME-
00:0f.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8029(AS)
Subsystem: Realtek Semiconductor Co., Ltd. RT8029(AS) Control:
I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- Status: Cap- 66Mhz- UDF- FastB2B-
ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin A routed to IRQ 5 Region 0: I/O ports at cc00
[size=32]
01:00.0 VGA compatible controller: nVidia Corporation NV11 (GeForce2 MX)
(rev b2) (prog-if 00 [VGA])
Subsystem: ABIT Computer Corp.: Unknown device 6109 Control:
I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- Status: Cap+ 66Mhz+ UDF- FastB2B+
ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (1250ns min, 250ns max) Interrupt: pin A routed to
IRQ 11 Region 0: Memory at ce000000 (32-bit, non-prefetchable)
[size=16M] Region 1: Memory at c0000000 (32-bit, prefetchable)
[size=128M] Expansion ROM at cfef0000 [disabled] [size=64K]
Capabilities: [60] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 PME-Enable-
DSel=0 DScale=0 PME-
Capabilities: [44] AGP version 2.0
Status: RQ=31 SBA- 64bit- FW+ Rate=x1,x2
Command: RQ=0 SBA- AGP- 64bit- FW- Rate=<none>
^ permalink raw reply [flat|nested] 13+ messages in thread
* Re: 2.4.20-pre3 boot hang
2002-08-18 18:06 ` Markus Plail
@ 2002-08-18 18:22 ` Alan Cox
2002-08-19 7:57 ` Markus Plail
0 siblings, 1 reply; 13+ messages in thread
From: Alan Cox @ 2002-08-18 18:22 UTC (permalink / raw)
To: Markus Plail; +Cc: linux mailing-list
On Sun, 2002-08-18 at 19:06, Markus Plail wrote:
> Apart from that, the latest ac series oopses when I try to mount a CD
> in a drive driven by ide-scsi emulation. And the IDE performance was
> quite a bit worse than 2.4.18. Sorry for not being able to make more
> concrete statements, just wanted to mention it.
Oops log, dmesg boot log of 2.4.18 and 2.4.20pre2-ac3 ?
^ permalink raw reply [flat|nested] 13+ messages in thread
* Re: 2.4.20-pre3 boot hang
2002-08-18 15:31 2.4.20-pre3 boot hang Klaus Dittrich
2002-08-18 18:06 ` Markus Plail
@ 2002-08-18 18:42 ` Erik Andersen
2002-08-18 20:03 ` Andre Hedrick
2002-08-19 11:13 ` Mauricio Pretto
2 siblings, 1 reply; 13+ messages in thread
From: Erik Andersen @ 2002-08-18 18:42 UTC (permalink / raw)
To: linux mailing-list
On Sun Aug 18, 2002 at 05:31:45PM +0200, Klaus Dittrich wrote:
> SMP, P-III, Intel-BX
>
> booting Linux 2.4.20-pre3 stops after
>
> Linux NET4.0 for Linux 2.4
> Based upon Swansea University Computer Society NET3.039
> Initializing RT netlink socket
On my UP Athlon, booting 2.4.20-pre3 hangs right after
the "apm: BIOS version" message...
-Erik
--
Erik B. Andersen http://codepoet-consulting.com/
--This message was written using 73% post-consumer electrons--
^ permalink raw reply [flat|nested] 13+ messages in thread
* Re: 2.4.20-pre3 boot hang
2002-08-18 18:42 ` Erik Andersen
@ 2002-08-18 20:03 ` Andre Hedrick
2002-08-18 20:18 ` Erik Andersen
0 siblings, 1 reply; 13+ messages in thread
From: Andre Hedrick @ 2002-08-18 20:03 UTC (permalink / raw)
To: Erik Andersen; +Cc: linux mailing-list
Turn of APM first please, if anyone knows the game you do :-P
On Sun, 18 Aug 2002, Erik Andersen wrote:
> On Sun Aug 18, 2002 at 05:31:45PM +0200, Klaus Dittrich wrote:
> > SMP, P-III, Intel-BX
> >
> > booting Linux 2.4.20-pre3 stops after
> >
> > Linux NET4.0 for Linux 2.4
> > Based upon Swansea University Computer Society NET3.039
> > Initializing RT netlink socket
>
> On my UP Athlon, booting 2.4.20-pre3 hangs right after
> the "apm: BIOS version" message...
>
> -Erik
>
> --
> Erik B. Andersen http://codepoet-consulting.com/
> --This message was written using 73% post-consumer electrons--
> -
> To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
> the body of a message to majordomo@vger.kernel.org
> More majordomo info at http://vger.kernel.org/majordomo-info.html
> Please read the FAQ at http://www.tux.org/lkml/
>
Andre Hedrick
LAD Storage Consulting Group
^ permalink raw reply [flat|nested] 13+ messages in thread
* Re: 2.4.20-pre3 boot hang
2002-08-18 20:03 ` Andre Hedrick
@ 2002-08-18 20:18 ` Erik Andersen
0 siblings, 0 replies; 13+ messages in thread
From: Erik Andersen @ 2002-08-18 20:18 UTC (permalink / raw)
To: Andre Hedrick; +Cc: linux mailing-list
On Sun Aug 18, 2002 at 01:03:42PM -0700, Andre Hedrick wrote:
>
> Turn of APM first please, if anyone knows the game you do :-P
I did of course. :) Booting with "apm=off" makes it boot.
-Erik
--
Erik B. Andersen http://codepoet-consulting.com/
--This message was written using 73% post-consumer electrons--
^ permalink raw reply [flat|nested] 13+ messages in thread
* Re: 2.4.20-pre3 boot hang
2002-08-18 18:22 ` Alan Cox
@ 2002-08-19 7:57 ` Markus Plail
2002-08-19 12:18 ` Alan Cox
0 siblings, 1 reply; 13+ messages in thread
From: Markus Plail @ 2002-08-19 7:57 UTC (permalink / raw)
To: linux mailing-list
[-- Attachment #1: Type: text/plain, Size: 587 bytes --]
Hi Alan!
* Alan Cox writes:
>On Sun, 2002-08-18 at 19:06, Markus Plail wrote:
>>Apart from that, the latest ac series oopses when I try to mount a CD
>>in a drive driven by ide-scsi emulation. And the IDE performance was
>>quite a bit worse than 2.4.18. Sorry for not being able to make more
>>concrete statements, just wanted to mention it.
>Oops log, dmesg boot log of 2.4.18 and 2.4.20pre2-ac3 ?
Here it comes. I tried ac4 this morning and it's still the same.
regards
Markus
PS: Can you tell me if it is theoretically possible to burn CDs DAO/RAW
under Linux with DMA enabled?
[-- Attachment #2: dmesg_2.4.20-pre2-ac4.txt --]
[-- Type: text/plain, Size: 15321 bytes --]
Aug 19 09:42:49 plailis syslogd 1.4.1: restart.
Aug 19 09:42:49 plailis kernel: klogd 1.4.1, log source = /proc/kmsg started.
Aug 19 09:42:49 plailis kernel: Inspecting /boot/System.map
Aug 19 09:42:49 plailis kernel: Loaded 18159 symbols from /boot/System.map.
Aug 19 09:42:49 plailis kernel: Symbols match kernel version 2.4.20.
Aug 19 09:42:49 plailis kernel: Loaded 61 symbols from 8 modules.
Aug 19 09:42:49 plailis kernel: Linux version 2.4.20-pre2-ac4 (root@plailis_lfs) (gcc version 2.95.3 20010315 (release)) #1 Mon Aug 19 09:28:26 CEST 2002
Aug 19 09:42:49 plailis kernel: BIOS-provided physical RAM map:
Aug 19 09:42:49 plailis kernel: BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
Aug 19 09:42:49 plailis kernel: BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
Aug 19 09:42:49 plailis kernel: BIOS-e820: 00000000000ee000 - 0000000000100000 (reserved)
Aug 19 09:42:49 plailis kernel: BIOS-e820: 0000000000100000 - 000000000fff0000 (usable)
Aug 19 09:42:49 plailis kernel: BIOS-e820: 000000000fff0000 - 000000000fff8000 (ACPI data)
Aug 19 09:42:49 plailis kernel: BIOS-e820: 000000000fff8000 - 0000000010000000 (ACPI NVS)
Aug 19 09:42:49 plailis kernel: BIOS-e820: 00000000fec00000 - 00000000fec01000 (reserved)
Aug 19 09:42:49 plailis kernel: BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
Aug 19 09:42:49 plailis kernel: BIOS-e820: 00000000ffee0000 - 00000000fff00000 (reserved)
Aug 19 09:42:49 plailis kernel: BIOS-e820: 00000000fffc0000 - 0000000100000000 (reserved)
Aug 19 09:42:49 plailis kernel: 255MB LOWMEM available.
Aug 19 09:42:49 plailis kernel: On node 0 totalpages: 65520
Aug 19 09:42:49 plailis kernel: zone(0): 4096 pages.
Aug 19 09:42:49 plailis kernel: zone(1): 61424 pages.
Aug 19 09:42:49 plailis kernel: zone(2): 0 pages.
Aug 19 09:42:49 plailis kernel: Kernel command line: BOOT_IMAGE=lfsneu ro root=307 hdc=ide-scsi hdd=ide-scsi
Aug 19 09:42:49 plailis kernel: ide_setup: hdc=ide-scsi
Aug 19 09:42:49 plailis kernel: ide_setup: hdd=ide-scsi
Aug 19 09:42:49 plailis kernel: Local APIC disabled by BIOS -- reenabling.
Aug 19 09:42:49 plailis kernel: Found and enabled local APIC!
Aug 19 09:42:49 plailis kernel: Initializing CPU#0
Aug 19 09:42:49 plailis kernel: Detected 1526.845 MHz processor.
Aug 19 09:42:49 plailis kernel: Console: colour VGA+ 80x25
Aug 19 09:42:49 plailis kernel: Calibrating delay loop... 3047.42 BogoMIPS
Aug 19 09:42:49 plailis kernel: Memory: 256048k/262080k available (1401k kernel code, 5644k reserved, 551k data, 100k init, 0k highmem)
Aug 19 09:42:49 plailis kernel: Dentry cache hash table entries: 32768 (order: 6, 262144 bytes)
Aug 19 09:42:49 plailis kernel: Inode cache hash table entries: 16384 (order: 5, 131072 bytes)
Aug 19 09:42:49 plailis kernel: Mount cache hash table entries: 512 (order: 0, 4096 bytes)
Aug 19 09:42:49 plailis kernel: ramfs: mounted with options: <defaults>
Aug 19 09:42:49 plailis kernel: ramfs: max_pages=32006 max_file_pages=0 max_inodes=0 max_dentries=32006
Aug 19 09:42:49 plailis kernel: Buffer cache hash table entries: 16384 (order: 4, 65536 bytes)
Aug 19 09:42:49 plailis kernel: Page-cache hash table entries: 65536 (order: 6, 262144 bytes)
Aug 19 09:42:49 plailis kernel: CPU: Before vendor init, caps: 0383fbff c1cbfbff 00000000, vendor = 2
Aug 19 09:42:49 plailis kernel: CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
Aug 19 09:42:49 plailis kernel: CPU: L2 Cache: 256K (64 bytes/line)
Aug 19 09:42:49 plailis kernel: CPU: After vendor init, caps: 0383fbff c1cbfbff 00000000 00000000
Aug 19 09:42:49 plailis kernel: Intel machine check architecture supported.
Aug 19 09:42:49 plailis kernel: Intel machine check reporting enabled on CPU#0.
Aug 19 09:42:49 plailis kernel: CPU: After generic, caps: 0383fbff c1cbfbff 00000000 00000000
Aug 19 09:42:49 plailis kernel: CPU: Common caps: 0383fbff c1cbfbff 00000000 00000000
Aug 19 09:42:49 plailis kernel: CPU: AMD Athlon(tm) XP 1800+ stepping 02
Aug 19 09:42:49 plailis kernel: Enabling fast FPU save and restore... done.
Aug 19 09:42:49 plailis kernel: Enabling unmasked SIMD FPU exception support... done.
Aug 19 09:42:49 plailis kernel: Checking 'hlt' instruction... OK.
Aug 19 09:42:49 plailis kernel: POSIX conformance testing by UNIFIX
Aug 19 09:42:49 plailis kernel: enabled ExtINT on CPU#0
Aug 19 09:42:49 plailis kernel: ESR value before enabling vector: 00000000
Aug 19 09:42:49 plailis kernel: ESR value after enabling vector: 00000000
Aug 19 09:42:49 plailis kernel: Using local APIC timer interrupts.
Aug 19 09:42:49 plailis kernel: calibrating APIC timer ...
Aug 19 09:42:49 plailis kernel: ..... CPU clock speed is 1526.8678 MHz.
Aug 19 09:42:49 plailis kernel: ..... host bus clock speed is 265.5422 MHz.
Aug 19 09:42:49 plailis kernel: cpu: 0, clocks: 2655422, slice: 1327711
Aug 19 09:42:49 plailis kernel: CPU0<T0:2655408,T1:1327696,D:1,S:1327711,C:2655422>
Aug 19 09:42:49 plailis kernel: mtrr: v1.40 (20010327) Richard Gooch (rgooch@atnf.csiro.au)
Aug 19 09:42:49 plailis kernel: mtrr: detected mtrr type: Intel
Aug 19 09:42:49 plailis kernel: PCI: PCI BIOS revision 2.10 entry at 0xfdb01, last bus=1
Aug 19 09:42:49 plailis kernel: PCI: Using configuration type 1
Aug 19 09:42:49 plailis kernel: PCI: Probing PCI hardware
Aug 19 09:42:49 plailis kernel: Unknown bridge resource 0: assuming transparent
Aug 19 09:42:49 plailis kernel: PCI: Using IRQ router SIS [1039/0008] at 00:02.0
Aug 19 09:42:49 plailis kernel: PnPBIOS: Found PnP BIOS installation structure at 0xc00f7160
Aug 19 09:42:49 plailis kernel: PnPBIOS: PnP BIOS version 1.0, entry 0xf0000:0x5c17, dseg 0xf0000
Aug 19 09:42:49 plailis kernel: PnPBIOS: 13 nodes reported by PnP BIOS; 13 recorded by driver
Aug 19 09:42:49 plailis kernel: Linux NET4.0 for Linux 2.4
Aug 19 09:42:49 plailis kernel: Based upon Swansea University Computer Society NET3.039
Aug 19 09:42:49 plailis kernel: Initializing RT netlink socket
Aug 19 09:42:49 plailis kernel: Starting kswapd
Aug 19 09:42:49 plailis kernel: Journalled Block Device driver loaded
Aug 19 09:42:49 plailis kernel: Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
Aug 19 09:42:49 plailis kernel: ACPI: Core Subsystem version [20011018]
Aug 19 09:42:49 plailis kernel: ACPI: Subsystem enabled
Aug 19 09:42:49 plailis kernel: Detected PS/2 Mouse Port.
Aug 19 09:42:49 plailis kernel: pty: 256 Unix98 ptys configured
Aug 19 09:42:49 plailis kernel: Serial driver version 5.05c (2001-07-08) with MANY_PORTS SHARE_IRQ SERIAL_PCI enabled
Aug 19 09:42:49 plailis kernel: ttyS00 at 0x03f8 (irq = 4) is a 16550A
Aug 19 09:42:49 plailis kernel: ttyS01 at 0x02f8 (irq = 3) is a 16550A
Aug 19 09:42:49 plailis kernel: Real Time Clock Driver v1.10e
Aug 19 09:42:49 plailis kernel: Uniform Multi-Platform E-IDE driver Revision: 6.31
Aug 19 09:42:49 plailis kernel: ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
Aug 19 09:42:49 plailis kernel: SIS5513: IDE controller on PCI bus 00 dev 15
Aug 19 09:42:49 plailis kernel: SIS5513: chipset revision 208
Aug 19 09:42:49 plailis kernel: SIS5513: not 100%% native mode: will probe irqs later
Aug 19 09:42:49 plailis kernel: SiS735 ATA 100 controller
Aug 19 09:42:49 plailis kernel: ide0: BM-DMA at 0xff00-0xff07, BIOS settings: hda:DMA, hdb:DMA
Aug 19 09:42:49 plailis kernel: ide1: BM-DMA at 0xff08-0xff0f, BIOS settings: hdc:DMA, hdd:DMA
Aug 19 09:42:49 plailis kernel: hda: SAMSUNG SV6004H, ATA DISK drive
Aug 19 09:42:49 plailis kernel: ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
Aug 19 09:42:49 plailis kernel: hdc: 20X10, ATAPI CD/DVD-ROM drive
Aug 19 09:42:49 plailis kernel: hdd: TOSHIBA DVD-ROM SD-M1612, ATAPI CD/DVD-ROM drive
Aug 19 09:42:49 plailis kernel: ide1 at 0x170-0x177,0x376 on irq 15
Aug 19 09:42:49 plailis kernel: hda: host protected area => 1
Aug 19 09:42:49 plailis kernel: hda: 117306000 sectors (60061 MB) w/468KiB Cache, CHS=7301/255/63, UDMA(100)
Aug 19 09:42:49 plailis kernel: ide-floppy driver 0.99.newide
Aug 19 09:42:49 plailis kernel: Partition check:
Aug 19 09:42:49 plailis kernel: hda: hda1 hda2 < hda5 hda6 hda7 hda8 hda9 hda10 hda11 >
Aug 19 09:42:49 plailis kernel: Floppy drive(s): fd0 is 1.44M
Aug 19 09:42:49 plailis kernel: FDC 0 is a post-1991 82077
Aug 19 09:42:49 plailis kernel: ide-floppy driver 0.99.newide
Aug 19 09:42:49 plailis kernel: SCSI subsystem driver Revision: 1.00
Aug 19 09:42:49 plailis kernel: PCI: Found IRQ 11 for device 00:09.0
Aug 19 09:42:49 plailis kernel: sym53c8xx: at PCI bus 0, device 9, function 0
Aug 19 09:42:49 plailis kernel: sym53c8xx: setting PCI_COMMAND_PARITY...(fix-up)
Aug 19 09:42:49 plailis kernel: sym53c8xx: 53c875 detected
Aug 19 09:42:49 plailis kernel: sym53c875-0: rev 0x26 on pci bus 0 device 9 function 0 irq 11
Aug 19 09:42:49 plailis kernel: sym53c875-0: ID 7, Fast-20, Parity Checking
Aug 19 09:42:49 plailis kernel: scsi0 : sym53c8xx-1.7.3c-20010512
Aug 19 09:42:49 plailis kernel: scsi1 : SCSI host adapter emulation for IDE ATAPI devices
Aug 19 09:42:49 plailis kernel: Vendor: ATAPI Model: CD-R/RW 20X10 Rev: H.JH
Aug 19 09:42:49 plailis kernel: Type: CD-ROM ANSI SCSI revision: 02
Aug 19 09:42:49 plailis kernel: Vendor: TOSHIBA Model: DVD-ROM SD-M1612 Rev: 1004
Aug 19 09:42:49 plailis kernel: Type: CD-ROM ANSI SCSI revision: 02
Aug 19 09:42:49 plailis kernel: Attached scsi CD-ROM sr0 at scsi1, channel 0, id 0, lun 0
Aug 19 09:42:49 plailis kernel: Attached scsi CD-ROM sr1 at scsi1, channel 0, id 1, lun 0
Aug 19 09:42:49 plailis kernel: sr0: scsi3-mmc drive: 40x/40x writer cd/rw xa/form2 cdda tray
Aug 19 09:42:49 plailis kernel: Uniform CD-ROM driver Revision: 3.12
Aug 19 09:42:49 plailis kernel: sr1: scsi3-mmc drive: 48x/48x cd/rw xa/form2 cdda tray
Aug 19 09:42:49 plailis kernel: usb.c: registered new driver usbdevfs
Aug 19 09:42:49 plailis kernel: usb.c: registered new driver hub
Aug 19 09:42:49 plailis kernel: Initializing USB Mass Storage driver...
Aug 19 09:42:49 plailis kernel: usb.c: registered new driver usb-storage
Aug 19 09:42:49 plailis kernel: USB Mass Storage support registered.
Aug 19 09:42:49 plailis kernel: NET4: Linux TCP/IP 1.0 for NET4.0
Aug 19 09:42:49 plailis kernel: IP Protocols: ICMP, UDP, TCP, IGMP
Aug 19 09:42:49 plailis kernel: IP: routing cache hash table of 2048 buckets, 16Kbytes
Aug 19 09:42:49 plailis kernel: TCP: Hash tables configured (established 16384 bind 32768)
Aug 19 09:42:49 plailis kernel: NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
Aug 19 09:42:49 plailis kernel: EXT3-fs: INFO: recovery required on readonly filesystem.
Aug 19 09:42:49 plailis kernel: EXT3-fs: write access will be enabled during recovery.
Aug 19 09:42:49 plailis kernel: kjournald starting. Commit interval 5 seconds
Aug 19 09:42:49 plailis kernel: EXT3-fs: recovery complete.
Aug 19 09:42:49 plailis kernel: EXT3-fs: mounted filesystem with ordered data mode.
Aug 19 09:42:49 plailis kernel: VFS: Mounted root (ext3 filesystem) readonly.
Aug 19 09:42:49 plailis kernel: Freeing unused kernel memory: 100k freed
Aug 19 09:42:49 plailis kernel: Adding Swap: 128480k swap-space (priority -1)
Aug 19 09:42:49 plailis kernel: SiS router pirq escape (99)
Aug 19 09:42:49 plailis kernel: SiS router pirq escape (99)
Aug 19 09:42:49 plailis kernel: usb-ohci.c: USB OHCI at membase 0xd0832000, IRQ 10
Aug 19 09:42:49 plailis kernel: usb-ohci.c: usb-00:02.3, Silicon Integrated Systems [SiS] 7001 (#2)
Aug 19 09:42:49 plailis kernel: usb.c: new USB bus registered, assigned bus number 1
Aug 19 09:42:49 plailis kernel: hub.c: USB hub found
Aug 19 09:42:49 plailis kernel: hub.c: 3 ports detected
Aug 19 09:42:49 plailis kernel: PCI: Found IRQ 5 for device 00:02.2
Aug 19 09:42:49 plailis kernel: PCI: Sharing IRQ 5 with 00:0f.0
Aug 19 09:42:49 plailis kernel: usb-ohci.c: USB OHCI at membase 0xd0834000, IRQ 5
Aug 19 09:42:49 plailis kernel: usb-ohci.c: usb-00:02.2, Silicon Integrated Systems [SiS] 7001
Aug 19 09:42:49 plailis kernel: usb.c: new USB bus registered, assigned bus number 2
Aug 19 09:42:49 plailis kernel: hub.c: USB hub found
Aug 19 09:42:49 plailis kernel: hub.c: 3 ports detected
Aug 19 09:42:49 plailis kernel: usb.c: registered new driver usblp
Aug 19 09:42:49 plailis kernel: printer.c: v0.11: USB Printer Device Class driver
Aug 19 09:42:49 plailis kernel: mice: PS/2 mouse device common for all mice
Aug 19 09:42:49 plailis kernel: usb.c: registered new driver hid
Aug 19 09:42:49 plailis kernel: hid-core.c: v1.8.1 Andreas Gal, Vojtech Pavlik <vojtech@suse.cz>
Aug 19 09:42:49 plailis kernel: hid-core.c: USB HID support drivers
Aug 19 09:42:49 plailis kernel: EXT3 FS 2.4-0.9.18, 14 May 2002 on ide0(3,7), internal journal
Aug 19 09:42:49 plailis kernel: NTFS driver v1.1.22 [Flags: R/O MODULE]
Aug 19 09:42:49 plailis kernel: NTFS: Warning! NTFS volume version is Win2k+: Mounting read-only
Aug 19 09:42:49 plailis kernel: kjournald starting. Commit interval 5 seconds
Aug 19 09:42:49 plailis kernel: EXT3 FS 2.4-0.9.18, 14 May 2002 on ide0(3,9), internal journal
Aug 19 09:42:49 plailis kernel: EXT3-fs: mounted filesystem with ordered data mode.
Aug 19 09:42:49 plailis kernel: kjournald starting. Commit interval 5 seconds
Aug 19 09:42:49 plailis kernel: EXT3 FS 2.4-0.9.18, 14 May 2002 on ide0(3,8), internal journal
Aug 19 09:42:49 plailis kernel: EXT3-fs: mounted filesystem with ordered data mode.
Aug 19 09:42:49 plailis kernel: kjournald starting. Commit interval 5 seconds
Aug 19 09:42:49 plailis kernel: EXT3 FS 2.4-0.9.18, 14 May 2002 on ide0(3,10), internal journal
Aug 19 09:42:49 plailis kernel: EXT3-fs: mounted filesystem with ordered data mode.
Aug 19 09:42:49 plailis kernel: kjournald starting. Commit interval 5 seconds
Aug 19 09:42:49 plailis kernel: EXT3 FS 2.4-0.9.18, 14 May 2002 on ide0(3,11), internal journal
Aug 19 09:42:49 plailis kernel: EXT3-fs: mounted filesystem with ordered data mode.
Aug 19 09:42:49 plailis kernel: devpts: called with bogus options
Aug 19 09:42:49 plailis kernel: hub.c: USB new device connect on bus2/1, assigned device number 2
Aug 19 09:42:49 plailis kernel: input0,hiddev0: USB HID v1.10 Keyboard [Logitech USB Receiver] on usb2:2.0
Aug 19 09:42:49 plailis kernel: input1,hiddev0: USB HID v1.10 Mouse [Logitech USB Receiver] on usb2:2.1
Aug 19 09:42:49 plailis kernel: ne2k-pci.c:v1.02 10/19/2000 D. Becker/P. Gortmaker
Aug 19 09:42:49 plailis kernel: http://www.scyld.com/network/ne2k-pci.html
Aug 19 09:42:49 plailis kernel: PCI: Found IRQ 5 for device 00:0f.0
Aug 19 09:42:49 plailis kernel: PCI: Sharing IRQ 5 with 00:02.2
Aug 19 09:42:49 plailis kernel: eth0: RealTek RTL-8029 found at 0xcc00, IRQ 5, 00:40:95:45:11:CF.
Aug 19 09:42:51 plailis kernel: sis900.c: v1.08.04 4/25/2002
Aug 19 09:42:51 plailis kernel: PCI: Assigned IRQ 12 for device 00:03.0
Aug 19 09:42:51 plailis kernel: eth1: Realtek RTL8201 PHY transceiver found at address 1.
Aug 19 09:42:51 plailis kernel: eth1: Using transceiver found at address 1 as default
Aug 19 09:42:51 plailis kernel: eth1: SiS 900 PCI Fast Ethernet at 0xd400, IRQ 12, 00:07:95:a8:9c:f9.
Aug 19 09:42:52 plailis kernel: eth1: Media Link On 10mbps half-duplex
Aug 19 09:42:52 plailis kernel: CSLIP: code copyright 1989 Regents of the University of California
Aug 19 09:42:52 plailis kernel: PPP generic driver version 2.4.2
[-- Attachment #3: dmesg_2.4.18.txt --]
[-- Type: text/plain, Size: 12906 bytes --]
Aug 13 19:01:19 plailis syslogd 1.4.1: restart.
Aug 13 19:01:19 plailis kernel: klogd 1.4.1, log source = /proc/kmsg started.
Aug 13 19:01:19 plailis kernel: Inspecting /boot/System.map
Aug 13 19:01:19 plailis kernel: Loaded 16679 symbols from /boot/System.map.
Aug 13 19:01:19 plailis kernel: Symbols match kernel version 2.4.18.
Aug 13 19:01:19 plailis kernel: Loaded 107 symbols from 11 modules.
Aug 13 19:01:19 plailis kernel: Linux version 2.4.18 (root@plailis_lfs) (gcc version 2.95.3 20010315 (release)) #1 Die Aug 13 18:53:01 CEST 2002
Aug 13 19:01:19 plailis kernel: BIOS-provided physical RAM map:
Aug 13 19:01:19 plailis kernel: BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
Aug 13 19:01:19 plailis kernel: BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
Aug 13 19:01:19 plailis kernel: BIOS-e820: 00000000000ee000 - 0000000000100000 (reserved)
Aug 13 19:01:19 plailis kernel: BIOS-e820: 0000000000100000 - 000000000fff0000 (usable)
Aug 13 19:01:19 plailis kernel: BIOS-e820: 000000000fff0000 - 000000000fff8000 (ACPI data)
Aug 13 19:01:19 plailis kernel: BIOS-e820: 000000000fff8000 - 0000000010000000 (ACPI NVS)
Aug 13 19:01:19 plailis kernel: BIOS-e820: 00000000fec00000 - 00000000fec01000 (reserved)
Aug 13 19:01:19 plailis kernel: BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
Aug 13 19:01:19 plailis kernel: BIOS-e820: 00000000ffee0000 - 00000000fff00000 (reserved)
Aug 13 19:01:19 plailis kernel: BIOS-e820: 00000000fffc0000 - 0000000100000000 (reserved)
Aug 13 19:01:19 plailis kernel: On node 0 totalpages: 65520
Aug 13 19:01:19 plailis kernel: zone(0): 4096 pages.
Aug 13 19:01:19 plailis kernel: zone(1): 61424 pages.
Aug 13 19:01:19 plailis kernel: zone(2): 0 pages.
Aug 13 19:01:19 plailis kernel: Local APIC disabled by BIOS -- reenabling.
Aug 13 19:01:19 plailis kernel: Found and enabled local APIC!
Aug 13 19:01:19 plailis kernel: Kernel command line: BOOT_IMAGE=lfsneu ro root=307 hdc=ide-scsi hdd=ide-scsi
Aug 13 19:01:19 plailis kernel: ide_setup: hdc=ide-scsi
Aug 13 19:01:19 plailis kernel: ide_setup: hdd=ide-scsi
Aug 13 19:01:19 plailis kernel: Initializing CPU#0
Aug 13 19:01:19 plailis kernel: Detected 1526.847 MHz processor.
Aug 13 19:01:19 plailis kernel: Console: colour VGA+ 80x25
Aug 13 19:01:19 plailis kernel: Calibrating delay loop... 3047.42 BogoMIPS
Aug 13 19:01:19 plailis kernel: Memory: 255496k/262080k available (1262k kernel code, 6196k reserved, 366k data, 224k init, 0k highmem)
Aug 13 19:01:19 plailis kernel: Dentry-cache hash table entries: 32768 (order: 6, 262144 bytes)
Aug 13 19:01:19 plailis kernel: Inode-cache hash table entries: 16384 (order: 5, 131072 bytes)
Aug 13 19:01:19 plailis kernel: Mount-cache hash table entries: 4096 (order: 3, 32768 bytes)
Aug 13 19:01:19 plailis kernel: Buffer-cache hash table entries: 16384 (order: 4, 65536 bytes)
Aug 13 19:01:19 plailis kernel: Page-cache hash table entries: 65536 (order: 6, 262144 bytes)
Aug 13 19:01:19 plailis kernel: CPU: Before vendor init, caps: 0383fbff c1cbfbff 00000000, vendor = 2
Aug 13 19:01:19 plailis kernel: CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
Aug 13 19:01:19 plailis kernel: CPU: L2 Cache: 256K (64 bytes/line)
Aug 13 19:01:19 plailis kernel: CPU: After vendor init, caps: 0383fbff c1cbfbff 00000000 00000000
Aug 13 19:01:19 plailis kernel: Intel machine check architecture supported.
Aug 13 19:01:19 plailis kernel: Intel machine check reporting enabled on CPU#0.
Aug 13 19:01:19 plailis kernel: CPU: After generic, caps: 0383fbff c1cbfbff 00000000 00000000
Aug 13 19:01:19 plailis kernel: CPU: Common caps: 0383fbff c1cbfbff 00000000 00000000
Aug 13 19:01:19 plailis kernel: CPU: AMD Athlon(tm) XP 1800+ stepping 02
Aug 13 19:01:19 plailis kernel: Enabling fast FPU save and restore... done.
Aug 13 19:01:19 plailis kernel: Enabling unmasked SIMD FPU exception support... done.
Aug 13 19:01:19 plailis kernel: Checking 'hlt' instruction... OK.
Aug 13 19:01:19 plailis kernel: POSIX conformance testing by UNIFIX
Aug 13 19:01:19 plailis kernel: enabled ExtINT on CPU#0
Aug 13 19:01:19 plailis kernel: ESR value before enabling vector: 00000000
Aug 13 19:01:19 plailis kernel: ESR value after enabling vector: 00000000
Aug 13 19:01:19 plailis kernel: Using local APIC timer interrupts.
Aug 13 19:01:19 plailis kernel: calibrating APIC timer ...
Aug 13 19:01:19 plailis kernel: ..... CPU clock speed is 1526.9051 MHz.
Aug 13 19:01:19 plailis kernel: ..... host bus clock speed is 265.5488 MHz.
Aug 13 19:01:19 plailis kernel: cpu: 0, clocks: 2655488, slice: 1327744
Aug 13 19:01:19 plailis kernel: CPU0<T0:2655488,T1:1327744,D:0,S:1327744,C:2655488>
Aug 13 19:01:19 plailis kernel: mtrr: v1.40 (20010327) Richard Gooch (rgooch@atnf.csiro.au)
Aug 13 19:01:19 plailis kernel: mtrr: detected mtrr type: Intel
Aug 13 19:01:19 plailis kernel: PCI: PCI BIOS revision 2.10 entry at 0xfdb01, last bus=1
Aug 13 19:01:19 plailis kernel: PCI: Using configuration type 1
Aug 13 19:01:19 plailis kernel: PCI: Probing PCI hardware
Aug 13 19:01:19 plailis kernel: Unknown bridge resource 0: assuming transparent
Aug 13 19:01:19 plailis kernel: PCI: Using IRQ router SIS [1039/0008] at 00:02.0
Aug 13 19:01:19 plailis kernel: Linux NET4.0 for Linux 2.4
Aug 13 19:01:19 plailis kernel: Based upon Swansea University Computer Society NET3.039
Aug 13 19:01:19 plailis kernel: Initializing RT netlink socket
Aug 13 19:01:19 plailis kernel: Starting kswapd
Aug 13 19:01:19 plailis kernel: ACPI: Core Subsystem version [20011018]
Aug 13 19:01:19 plailis kernel: ACPI: Subsystem enabled
Aug 13 19:01:19 plailis kernel: Detected PS/2 Mouse Port.
Aug 13 19:01:19 plailis kernel: pty: 256 Unix98 ptys configured
Aug 13 19:01:19 plailis kernel: Serial driver version 5.05c (2001-07-08) with MANY_PORTS SHARE_IRQ SERIAL_PCI enabled
Aug 13 19:01:19 plailis kernel: ttyS00 at 0x03f8 (irq = 4) is a 16550A
Aug 13 19:01:19 plailis kernel: ttyS01 at 0x02f8 (irq = 3) is a 16550A
Aug 13 19:01:19 plailis kernel: Real Time Clock Driver v1.10e
Aug 13 19:01:19 plailis kernel: block: 128 slots per queue, batch=32
Aug 13 19:01:19 plailis kernel: Uniform Multi-Platform E-IDE driver Revision: 6.31
Aug 13 19:01:19 plailis kernel: ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
Aug 13 19:01:19 plailis kernel: SIS5513: IDE controller on PCI bus 00 dev 15
Aug 13 19:01:19 plailis kernel: SIS5513: chipset revision 208
Aug 13 19:01:19 plailis kernel: SIS5513: not 100%% native mode: will probe irqs later
Aug 13 19:01:19 plailis kernel: SiS735
Aug 13 19:01:19 plailis kernel: ide0: BM-DMA at 0xff00-0xff07, BIOS settings: hda:DMA, hdb:DMA
Aug 13 19:01:19 plailis kernel: ide1: BM-DMA at 0xff08-0xff0f, BIOS settings: hdc:DMA, hdd:DMA
Aug 13 19:01:19 plailis kernel: hda: SAMSUNG SV6004H, ATA DISK drive
Aug 13 19:01:19 plailis kernel: hdc: 20X10, ATAPI CD/DVD-ROM drive
Aug 13 19:01:19 plailis kernel: hdd: TOSHIBA DVD-ROM SD-M1612, ATAPI CD/DVD-ROM drive
Aug 13 19:01:19 plailis kernel: ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
Aug 13 19:01:19 plailis kernel: ide1 at 0x170-0x177,0x376 on irq 15
Aug 13 19:01:19 plailis kernel: hda: 117306000 sectors (60061 MB) w/468KiB Cache, CHS=7301/255/63, UDMA(100)
Aug 13 19:01:19 plailis kernel: ide-floppy driver 0.97.sv
Aug 13 19:01:19 plailis kernel: Partition check:
Aug 13 19:01:19 plailis kernel: hda: hda1 hda2 < hda5 hda6 hda7 hda8 hda9 hda10 hda11 >
Aug 13 19:01:19 plailis kernel: Floppy drive(s): fd0 is 1.44M
Aug 13 19:01:19 plailis kernel: FDC 0 is a post-1991 82077
Aug 13 19:01:19 plailis kernel: ide-floppy driver 0.97.sv
Aug 13 19:01:19 plailis kernel: SCSI subsystem driver Revision: 1.00
Aug 13 19:01:19 plailis kernel: PCI: Found IRQ 11 for device 00:09.0
Aug 13 19:01:19 plailis kernel: sym53c8xx: at PCI bus 0, device 9, function 0
Aug 13 19:01:19 plailis kernel: sym53c8xx: setting PCI_COMMAND_PARITY...(fix-up)
Aug 13 19:01:19 plailis kernel: sym53c8xx: 53c875 detected
Aug 13 19:01:19 plailis kernel: sym53c875-0: rev 0x26 on pci bus 0 device 9 function 0 irq 11
Aug 13 19:01:19 plailis kernel: sym53c875-0: ID 7, Fast-20, Parity Checking
Aug 13 19:01:19 plailis kernel: scsi0 : sym53c8xx-1.7.3c-20010512
Aug 13 19:01:19 plailis kernel: scsi1 : SCSI host adapter emulation for IDE ATAPI devices
Aug 13 19:01:19 plailis kernel: Vendor: ATAPI Model: CD-R/RW 20X10 Rev: H.JH
Aug 13 19:01:19 plailis kernel: Type: CD-ROM ANSI SCSI revision: 02
Aug 13 19:01:19 plailis kernel: Vendor: TOSHIBA Model: DVD-ROM SD-M1612 Rev: 1004
Aug 13 19:01:19 plailis kernel: Type: CD-ROM ANSI SCSI revision: 02
Aug 13 19:01:19 plailis kernel: Attached scsi CD-ROM sr0 at scsi1, channel 0, id 0, lun 0
Aug 13 19:01:19 plailis kernel: Attached scsi CD-ROM sr1 at scsi1, channel 0, id 1, lun 0
Aug 13 19:01:19 plailis kernel: sr0: scsi3-mmc drive: 40x/40x writer cd/rw xa/form2 cdda tray
Aug 13 19:01:19 plailis kernel: Uniform CD-ROM driver Revision: 3.12
Aug 13 19:01:19 plailis kernel: sr1: scsi3-mmc drive: 48x/48x cd/rw xa/form2 cdda tray
Aug 13 19:01:19 plailis kernel: usb.c: registered new driver usbdevfs
Aug 13 19:01:19 plailis kernel: usb.c: registered new driver hub
Aug 13 19:01:19 plailis kernel: Initializing USB Mass Storage driver...
Aug 13 19:01:19 plailis kernel: usb.c: registered new driver usb-storage
Aug 13 19:01:19 plailis kernel: USB Mass Storage support registered.
Aug 13 19:01:19 plailis kernel: NET4: Linux TCP/IP 1.0 for NET4.0
Aug 13 19:01:19 plailis kernel: IP Protocols: ICMP, UDP, TCP, IGMP
Aug 13 19:01:19 plailis kernel: IP: routing cache hash table of 2048 buckets, 16Kbytes
Aug 13 19:01:19 plailis kernel: TCP: Hash tables configured (established 16384 bind 16384)
Aug 13 19:01:19 plailis kernel: NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
Aug 13 19:01:19 plailis kernel: VFS: Mounted root (ext2 filesystem) readonly.
Aug 13 19:01:19 plailis kernel: Freeing unused kernel memory: 224k freed
Aug 13 19:01:19 plailis kernel: Adding Swap: 128480k swap-space (priority -1)
Aug 13 19:01:19 plailis kernel: SiS router pirq escape (99)
Aug 13 19:01:19 plailis kernel: SiS router pirq escape (99)
Aug 13 19:01:19 plailis kernel: usb-ohci.c: USB OHCI at membase 0xd0832000, IRQ 10
Aug 13 19:01:19 plailis kernel: usb-ohci.c: usb-00:02.3, Silicon Integrated Systems [SiS] 7001 (#2)
Aug 13 19:01:19 plailis kernel: usb.c: new USB bus registered, assigned bus number 1
Aug 13 19:01:19 plailis kernel: hub.c: USB hub found
Aug 13 19:01:19 plailis kernel: hub.c: 3 ports detected
Aug 13 19:01:19 plailis kernel: PCI: Found IRQ 5 for device 00:02.2
Aug 13 19:01:19 plailis kernel: PCI: Sharing IRQ 5 with 00:0f.0
Aug 13 19:01:19 plailis kernel: usb-ohci.c: USB OHCI at membase 0xd0834000, IRQ 5
Aug 13 19:01:19 plailis kernel: usb-ohci.c: usb-00:02.2, Silicon Integrated Systems [SiS] 7001
Aug 13 19:01:19 plailis kernel: usb.c: new USB bus registered, assigned bus number 2
Aug 13 19:01:19 plailis kernel: hub.c: USB hub found
Aug 13 19:01:19 plailis kernel: hub.c: 3 ports detected
Aug 13 19:01:19 plailis kernel: usb.c: registered new driver usblp
Aug 13 19:01:19 plailis kernel: printer.c: v0.8:USB Printer Device Class driver
Aug 13 19:01:19 plailis kernel: mice: PS/2 mouse device common for all mice
Aug 13 19:01:19 plailis kernel: usb.c: registered new driver hid
Aug 13 19:01:19 plailis kernel: hid-core.c: v1.8 Andreas Gal, Vojtech Pavlik <vojtech@suse.cz>
Aug 13 19:01:19 plailis kernel: hid-core.c: USB HID support drivers
Aug 13 19:01:19 plailis kernel: NTFS driver v1.1.22 [Flags: R/O MODULE]
Aug 13 19:01:19 plailis kernel: NTFS: Warning! NTFS volume version is Win2k+: Mounting read-only
Aug 13 19:01:19 plailis kernel: devpts: called with bogus options
Aug 13 19:01:19 plailis kernel: hub.c: USB new device connect on bus2/1, assigned device number 2
Aug 13 19:01:19 plailis kernel: input0: USB HID v1.10 Keyboard [Logitech USB Receiver] on usb2:2.0
Aug 13 19:01:19 plailis kernel: input1: USB HID v1.10 Mouse [Logitech USB Receiver] on usb2:2.1
Aug 13 19:01:19 plailis kernel: ne2k-pci.c:v1.02 10/19/2000 D. Becker/P. Gortmaker
Aug 13 19:01:19 plailis kernel: http://www.scyld.com/network/ne2k-pci.html
Aug 13 19:01:19 plailis kernel: PCI: Found IRQ 5 for device 00:0f.0
Aug 13 19:01:19 plailis kernel: PCI: Sharing IRQ 5 with 00:02.2
Aug 13 19:01:19 plailis kernel: eth0: RealTek RTL-8029 found at 0xcc00, IRQ 5, 00:40:95:45:11:CF.
Aug 13 19:01:20 plailis kernel: sis900.c: v1.08.02 11/30/2001
Aug 13 19:01:20 plailis kernel: PCI: Assigned IRQ 12 for device 00:03.0
Aug 13 19:01:20 plailis kernel: eth1: Realtek RTL8201 PHY transceiver found at address 1.
Aug 13 19:01:20 plailis kernel: eth1: Using transceiver found at address 1 as default
Aug 13 19:01:20 plailis kernel: eth1: SiS 900 PCI Fast Ethernet at 0xd400, IRQ 12, 00:07:95:a8:9c:f9.
Aug 13 19:01:21 plailis kernel: eth1: Media Link On 10mbps half-duplex
[-- Attachment #4: oops.txt --]
[-- Type: text/plain, Size: 2340 bytes --]
Aug 19 09:41:22 plailis kernel: kernel BUG in header file at line 157
Aug 19 09:41:22 plailis kernel: kernel BUG at panic.c:286!
Aug 19 09:41:22 plailis kernel: invalid operand: 0000
Aug 19 09:41:22 plailis kernel: CPU: 0
Aug 19 09:41:22 plailis kernel: EIP: 0010:[__out_of_line_bug+15/32] Not tainted
Aug 19 09:41:22 plailis kernel: EIP: 0010:[<c01168df>] Not tainted
Aug 19 09:41:22 plailis kernel: EFLAGS: 00010282
Aug 19 09:41:22 plailis kernel: eax: 00000026 ebx: 00001000 ecx: c0309948 edx: ce872000
Aug 19 09:41:22 plailis kernel: esi: 00000001 edi: c13fe000 ebp: 00000000 esp: ce873d30
Aug 19 09:41:22 plailis kernel: ds: 0018 es: 0018 ss: 0018
Aug 19 09:41:22 plailis kernel: Process mount (pid: 564, stackpage=ce873000)
Aug 19 09:41:22 plailis kernel: Stack: c0265e00 0000009d c01cc6b1 0000009d cff01000 c0332f9c cee54d40 cee51000
Aug 19 09:41:22 plailis kernel: 00000000 c13fe000 00000001 c13fe000 c01cc8ab c0332db0 cee54d40 c0332db0
Aug 19 09:41:22 plailis kernel: c0332f9c cee54d40 cee51000 00000000 00000000 c0332db0 c01ccd39 c0332f9c
Aug 19 09:41:22 plailis kernel: Call Trace: [ide_build_sglist+321/384] [ide_build_dmatable+91/416] [__ide_dma_read+41/288] [idescsi_issue_pc+115/448] [idescsi_do_request+27/64]
Aug 19 09:41:22 plailis kernel: Call Trace: [<c01cc6b1>] [<c01cc8ab>] [<c01ccd39>] [<c01ecb63>] [<c01ecccb>]
Aug 19 09:41:22 plailis kernel: [start_request+374/464] [ide_do_request+618/704] [ide_do_drive_cmd+218/272] [idescsi_queue+1362/1440] [scsi_dispatch_cmd+426/544] [scsi_old_done+0/1472]
Aug 19 09:41:22 plailis kernel: [<c01c9576>] [<c01c988a>] [<c01c9e8a>] [<c01ed842>] [<c01db5aa>] [<c01e0340>]
Aug 19 09:41:22 plailis kernel: [scsi_request_fn+769/832] [generic_unplug_device+32/48] [__run_task_queue+76/96] [block_sync_page+22/32] [___wait_on_page+134/192] [do_generic_file_read+693/1024]
Aug 19 09:41:22 plailis kernel: [<c01e1b61>] [<c01bb650>] [<c011b0dc>] [<c0138ee6>] [<c0126946>] [<c0127255>]
Aug 19 09:41:22 plailis kernel: [generic_file_read+133/320] [file_read_actor+0/144] [sys_read+150/240] [system_call+51/56]
Aug 19 09:41:22 plailis kernel: [<c0127695>] [<c0127580>] [<c0135316>] [<c0106cd3>]
Aug 19 09:41:22 plailis kernel:
Aug 19 09:41:22 plailis kernel: Code: 0f 0b 1e 01 26 5e 26 c0 eb fe 8d b4 26 00 00 00 00 83 ec 18
[-- Attachment #5: ksymoops.txt --]
[-- Type: text/plain, Size: 4403 bytes --]
ksymoops 2.4.6 on i686 2.4.20-pre2-ac4. Options used
-V (default)
-k /proc/ksyms (default)
-l /proc/modules (default)
-o /lib/modules/2.4.20-pre2-ac4/ (default)
-m /usr/src/linux/System.map (default)
Warning: You did not tell me where to find symbol information. I will
assume that the log matches the kernel and modules that are running
right now and I'll use the default options above for symbol resolution.
If the current kernel and/or modules do not match the log, you can get
more accurate output by telling me the kernel version and where to find
map, modules, ksyms etc. ksymoops -h explains the options.
Aug 19 09:41:22 plailis kernel: kernel BUG in header file at line 157
Aug 19 09:41:22 plailis kernel: kernel BUG at panic.c:286!
Aug 19 09:41:22 plailis kernel: invalid operand: 0000
Aug 19 09:41:22 plailis kernel: CPU: 0
Aug 19 09:41:22 plailis kernel: EIP: 0010:[__out_of_line_bug+15/32] Not tainted
Aug 19 09:41:22 plailis kernel: EIP: 0010:[<c01168df>] Not tainted
Using defaults from ksymoops -t elf32-i386 -a i386
Aug 19 09:41:22 plailis kernel: EFLAGS: 00010282
Aug 19 09:41:22 plailis kernel: eax: 00000026 ebx: 00001000 ecx: c0309948 edx: ce872000
Aug 19 09:41:22 plailis kernel: esi: 00000001 edi: c13fe000 ebp: 00000000 esp: ce873d30
Aug 19 09:41:22 plailis kernel: ds: 0018 es: 0018 ss: 0018
Aug 19 09:41:22 plailis kernel: Process mount (pid: 564, stackpage=ce873000)
Aug 19 09:41:22 plailis kernel: Stack: c0265e00 0000009d c01cc6b1 0000009d cff01000 c0332f9c cee54d40 cee51000
Aug 19 09:41:22 plailis kernel: 00000000 c13fe000 00000001 c13fe000 c01cc8ab c0332db0 cee54d40 c0332db0
Aug 19 09:41:22 plailis kernel: c0332f9c cee54d40 cee51000 00000000 00000000 c0332db0 c01ccd39 c0332f9c
Aug 19 09:41:22 plailis kernel: Call Trace: [ide_build_sglist+321/384] [ide_build_dmatable+91/416] [__ide_dma_read+41/288] [idescsi_issue_pc+115/448] [idescsi_do_request+27/64]
Aug 19 09:41:22 plailis kernel: Call Trace: [<c01cc6b1>] [<c01cc8ab>] [<c01ccd39>] [<c01ecb63>] [<c01ecccb>]
Aug 19 09:41:22 plailis kernel: [<c01c9576>] [<c01c988a>] [<c01c9e8a>] [<c01ed842>] [<c01db5aa>] [<c01e0340>]
Aug 19 09:41:22 plailis kernel: [<c01e1b61>] [<c01bb650>] [<c011b0dc>] [<c0138ee6>] [<c0126946>] [<c0127255>]
Aug 19 09:41:22 plailis kernel: [<c0127695>] [<c0127580>] [<c0135316>] [<c0106cd3>]
Aug 19 09:41:22 plailis kernel: Code: 0f 0b 1e 01 26 5e 26 c0 eb fe 8d b4 26 00 00 00 00 83 ec 18
>>EIP; c01168df <__out_of_line_bug+f/20> <=====
>>ecx; c0309948 <runqueues+848/940>
>>edx; ce872000 <_end+e538b24/104f2b24>
>>edi; c13fe000 <_end+10c4b24/104f2b24>
>>esp; ce873d30 <_end+e53a854/104f2b24>
Trace; c01cc6b1 <ide_build_sglist+141/180>
Trace; c01cc8ab <ide_build_dmatable+5b/1a0>
Trace; c01ccd39 <__ide_dma_read+29/120>
Trace; c01ecb63 <idescsi_issue_pc+73/1c0>
Trace; c01ecccb <idescsi_do_request+1b/40>
Trace; c01c9576 <start_request+176/1d0>
Trace; c01c988a <ide_do_request+26a/2c0>
Trace; c01c9e8a <ide_do_drive_cmd+da/110>
Trace; c01ed842 <idescsi_queue+552/5a0>
Trace; c01db5aa <scsi_dispatch_cmd+1aa/220>
Trace; c01e0340 <scsi_old_done+0/5c0>
Trace; c01e1b61 <scsi_request_fn+301/340>
Trace; c01bb650 <generic_unplug_device+20/30>
Trace; c011b0dc <__run_task_queue+4c/60>
Trace; c0138ee6 <block_sync_page+16/20>
Trace; c0126946 <___wait_on_page+86/c0>
Trace; c0127255 <do_generic_file_read+2b5/400>
Trace; c0127695 <generic_file_read+85/140>
Trace; c0127580 <file_read_actor+0/90>
Trace; c0135316 <sys_read+96/f0>
Trace; c0106cd3 <system_call+33/38>
Code; c01168df <__out_of_line_bug+f/20>
00000000 <_EIP>:
Code; c01168df <__out_of_line_bug+f/20> <=====
0: 0f 0b ud2a <=====
Code; c01168e1 <__out_of_line_bug+11/20>
2: 1e push %ds
Code; c01168e2 <__out_of_line_bug+12/20>
3: 01 26 add %esp,(%esi)
Code; c01168e4 <__out_of_line_bug+14/20>
5: 5e pop %esi
Code; c01168e5 <__out_of_line_bug+15/20>
6: 26 es
Code; c01168e6 <__out_of_line_bug+16/20>
7: c0 eb fe shr $0xfe,%bl
Code; c01168e9 <__out_of_line_bug+19/20>
a: 8d b4 26 00 00 00 00 lea 0x0(%esi,1),%esi
Code; c01168f0 <do_syslog+0/2e0>
11: 83 ec 18 sub $0x18,%esp
1 warning issued. Results may not be reliable.
^ permalink raw reply [flat|nested] 13+ messages in thread
* Re: 2.4.20-pre3 boot hang
2002-08-18 15:31 2.4.20-pre3 boot hang Klaus Dittrich
2002-08-18 18:06 ` Markus Plail
2002-08-18 18:42 ` Erik Andersen
@ 2002-08-19 11:13 ` Mauricio Pretto
2002-08-19 11:38 ` Skidley
2 siblings, 1 reply; 13+ messages in thread
From: Mauricio Pretto @ 2002-08-19 11:13 UTC (permalink / raw)
Cc: linux mailing-list
[-- Attachment #1: Type: text/plain, Size: 447 bytes --]
Same Problem Here, athlon 1.1 , Right after Rt netlink socket it hangs.
My .config goes attach.
Klaus Dittrich wrote:
> SMP, P-III, Intel-BX
>
> booting Linux 2.4.20-pre3 stops after
>
> Linux NET4.0 for Linux 2.4
> Based upon Swansea University Computer Society NET3.039
> Initializing RT netlink socket
>
>
--
Mauricio Pretto
Gerente de Produtos
Interage Integradora
http://www.interage.com.br
Técnico Certificado Conectiva Linux
[-- Attachment #2: .config --]
[-- Type: text/plain, Size: 16534 bytes --]
#
# Automatically generated by make menuconfig: don't edit
#
CONFIG_X86=y
# CONFIG_SBUS is not set
CONFIG_UID16=y
#
# Code maturity level options
#
CONFIG_EXPERIMENTAL=y
#
# Loadable module support
#
CONFIG_MODULES=y
CONFIG_MODVERSIONS=y
CONFIG_KMOD=y
#
# Processor type and features
#
# CONFIG_M386 is not set
# CONFIG_M486 is not set
# CONFIG_M586 is not set
# CONFIG_M586TSC is not set
# CONFIG_M586MMX is not set
# CONFIG_M686 is not set
# CONFIG_MPENTIUMIII is not set
# CONFIG_MPENTIUM4 is not set
# CONFIG_MK6 is not set
CONFIG_MK7=y
# CONFIG_MELAN is not set
# CONFIG_MCRUSOE is not set
# CONFIG_MWINCHIPC6 is not set
# CONFIG_MWINCHIP2 is not set
# CONFIG_MWINCHIP3D is not set
# CONFIG_MCYRIXIII is not set
CONFIG_X86_WP_WORKS_OK=y
CONFIG_X86_INVLPG=y
CONFIG_X86_CMPXCHG=y
CONFIG_X86_XADD=y
CONFIG_X86_BSWAP=y
CONFIG_X86_POPAD_OK=y
# CONFIG_RWSEM_GENERIC_SPINLOCK is not set
CONFIG_RWSEM_XCHGADD_ALGORITHM=y
CONFIG_X86_L1_CACHE_SHIFT=6
CONFIG_X86_TSC=y
CONFIG_X86_GOOD_APIC=y
CONFIG_X86_USE_3DNOW=y
CONFIG_X86_PGE=y
CONFIG_X86_USE_PPRO_CHECKSUM=y
CONFIG_X86_F00F_WORKS_OK=y
CONFIG_X86_MCE=y
# CONFIG_TOSHIBA is not set
# CONFIG_I8K is not set
# CONFIG_MICROCODE is not set
# CONFIG_X86_MSR is not set
# CONFIG_X86_CPUID is not set
CONFIG_NOHIGHMEM=y
# CONFIG_HIGHMEM4G is not set
# CONFIG_HIGHMEM64G is not set
# CONFIG_HIGHMEM is not set
# CONFIG_MATH_EMULATION is not set
# CONFIG_MTRR is not set
# CONFIG_SMP is not set
# CONFIG_X86_UP_APIC is not set
# CONFIG_X86_UP_IOAPIC is not set
#
# General setup
#
CONFIG_NET=y
CONFIG_PCI=y
# CONFIG_PCI_GOBIOS is not set
# CONFIG_PCI_GODIRECT is not set
CONFIG_PCI_GOANY=y
CONFIG_PCI_BIOS=y
CONFIG_PCI_DIRECT=y
CONFIG_ISA=y
CONFIG_PCI_NAMES=y
# CONFIG_EISA is not set
# CONFIG_MCA is not set
# CONFIG_HOTPLUG is not set
# CONFIG_PCMCIA is not set
# CONFIG_HOTPLUG_PCI is not set
CONFIG_SYSVIPC=y
CONFIG_BSD_PROCESS_ACCT=y
CONFIG_SYSCTL=y
CONFIG_KCORE_ELF=y
# CONFIG_KCORE_AOUT is not set
CONFIG_BINFMT_AOUT=y
CONFIG_BINFMT_ELF=y
CONFIG_BINFMT_MISC=y
# CONFIG_PM is not set
# CONFIG_ACPI is not set
# CONFIG_APM is not set
#
# Memory Technology Devices (MTD)
#
# CONFIG_MTD is not set
#
# Parallel port support
#
# CONFIG_PARPORT is not set
#
# Plug and Play configuration
#
# CONFIG_PNP is not set
# CONFIG_ISAPNP is not set
#
# Block devices
#
CONFIG_BLK_DEV_FD=y
# CONFIG_BLK_DEV_XD is not set
# CONFIG_PARIDE is not set
# CONFIG_BLK_CPQ_DA is not set
# CONFIG_BLK_CPQ_CISS_DA is not set
# CONFIG_CISS_SCSI_TAPE is not set
# CONFIG_BLK_DEV_DAC960 is not set
# CONFIG_BLK_DEV_UMEM is not set
CONFIG_BLK_DEV_LOOP=y
CONFIG_BLK_DEV_NBD=y
# CONFIG_BLK_DEV_RAM is not set
# CONFIG_BLK_DEV_INITRD is not set
CONFIG_BLK_STATS=y
#
# Multi-device support (RAID and LVM)
#
# CONFIG_MD is not set
# CONFIG_BLK_DEV_MD is not set
# CONFIG_MD_LINEAR is not set
# CONFIG_MD_RAID0 is not set
# CONFIG_MD_RAID1 is not set
# CONFIG_MD_RAID5 is not set
# CONFIG_MD_MULTIPATH is not set
# CONFIG_BLK_DEV_LVM is not set
#
# Networking options
#
CONFIG_PACKET=y
# CONFIG_PACKET_MMAP is not set
# CONFIG_NETLINK_DEV is not set
CONFIG_NETFILTER=y
CONFIG_NETFILTER_DEBUG=y
# CONFIG_FILTER is not set
CONFIG_UNIX=y
CONFIG_INET=y
CONFIG_IP_MULTICAST=y
# CONFIG_IP_ADVANCED_ROUTER is not set
# CONFIG_IP_PNP is not set
# CONFIG_NET_IPIP is not set
# CONFIG_NET_IPGRE is not set
# CONFIG_IP_MROUTE is not set
# CONFIG_ARPD is not set
# CONFIG_INET_ECN is not set
CONFIG_SYN_COOKIES=y
#
# IP: Netfilter Configuration
#
CONFIG_IP_NF_CONNTRACK=y
CONFIG_IP_NF_FTP=y
CONFIG_IP_NF_IRC=y
CONFIG_IP_NF_QUEUE=y
CONFIG_IP_NF_IPTABLES=y
CONFIG_IP_NF_MATCH_LIMIT=y
CONFIG_IP_NF_MATCH_MAC=y
CONFIG_IP_NF_MATCH_PKTTYPE=y
CONFIG_IP_NF_MATCH_MARK=y
CONFIG_IP_NF_MATCH_MULTIPORT=y
CONFIG_IP_NF_MATCH_TOS=y
CONFIG_IP_NF_MATCH_ECN=y
CONFIG_IP_NF_MATCH_DSCP=y
CONFIG_IP_NF_MATCH_AH_ESP=y
CONFIG_IP_NF_MATCH_LENGTH=y
CONFIG_IP_NF_MATCH_TTL=y
CONFIG_IP_NF_MATCH_TCPMSS=y
CONFIG_IP_NF_MATCH_HELPER=y
CONFIG_IP_NF_MATCH_STATE=y
CONFIG_IP_NF_MATCH_CONNTRACK=y
CONFIG_IP_NF_MATCH_UNCLEAN=y
CONFIG_IP_NF_MATCH_OWNER=y
CONFIG_IP_NF_FILTER=y
CONFIG_IP_NF_TARGET_REJECT=y
CONFIG_IP_NF_TARGET_MIRROR=y
CONFIG_IP_NF_NAT=y
CONFIG_IP_NF_NAT_NEEDED=y
CONFIG_IP_NF_TARGET_MASQUERADE=y
CONFIG_IP_NF_TARGET_REDIRECT=y
CONFIG_IP_NF_NAT_LOCAL=y
CONFIG_IP_NF_NAT_SNMP_BASIC=y
CONFIG_IP_NF_NAT_IRC=y
CONFIG_IP_NF_NAT_FTP=y
CONFIG_IP_NF_MANGLE=y
CONFIG_IP_NF_TARGET_TOS=y
CONFIG_IP_NF_TARGET_ECN=y
CONFIG_IP_NF_TARGET_DSCP=y
CONFIG_IP_NF_TARGET_MARK=y
CONFIG_IP_NF_TARGET_LOG=y
CONFIG_IP_NF_TARGET_ULOG=y
CONFIG_IP_NF_TARGET_TCPMSS=y
CONFIG_IP_NF_ARPTABLES=y
CONFIG_IP_NF_ARPFILTER=y
# CONFIG_IPV6 is not set
# CONFIG_KHTTPD is not set
# CONFIG_ATM is not set
# CONFIG_VLAN_8021Q is not set
# CONFIG_IPX is not set
# CONFIG_ATALK is not set
#
# Appletalk devices
#
# CONFIG_DEV_APPLETALK is not set
# CONFIG_DECNET is not set
# CONFIG_BRIDGE is not set
# CONFIG_X25 is not set
# CONFIG_LAPB is not set
# CONFIG_LLC is not set
# CONFIG_NET_DIVERT is not set
# CONFIG_ECONET is not set
# CONFIG_WAN_ROUTER is not set
# CONFIG_NET_FASTROUTE is not set
# CONFIG_NET_HW_FLOWCONTROL is not set
#
# QoS and/or fair queueing
#
# CONFIG_NET_SCHED is not set
#
# Network testing
#
# CONFIG_NET_PKTGEN is not set
#
# Telephony Support
#
# CONFIG_PHONE is not set
# CONFIG_PHONE_IXJ is not set
# CONFIG_PHONE_IXJ_PCMCIA is not set
#
# ATA/IDE/MFM/RLL support
#
CONFIG_IDE=y
#
# IDE, ATA and ATAPI Block devices
#
CONFIG_BLK_DEV_IDE=y
# CONFIG_BLK_DEV_HD_IDE is not set
# CONFIG_BLK_DEV_HD is not set
CONFIG_BLK_DEV_IDEDISK=y
CONFIG_IDEDISK_MULTI_MODE=y
# CONFIG_IDEDISK_STROKE is not set
# CONFIG_BLK_DEV_IDEDISK_VENDOR is not set
# CONFIG_BLK_DEV_IDEDISK_FUJITSU is not set
# CONFIG_BLK_DEV_IDEDISK_IBM is not set
# CONFIG_BLK_DEV_IDEDISK_MAXTOR is not set
# CONFIG_BLK_DEV_IDEDISK_QUANTUM is not set
# CONFIG_BLK_DEV_IDEDISK_SEAGATE is not set
# CONFIG_BLK_DEV_IDEDISK_WD is not set
# CONFIG_BLK_DEV_COMMERIAL is not set
# CONFIG_BLK_DEV_TIVO is not set
# CONFIG_BLK_DEV_IDECS is not set
CONFIG_BLK_DEV_IDECD=y
# CONFIG_BLK_DEV_IDETAPE is not set
# CONFIG_BLK_DEV_IDEFLOPPY is not set
# CONFIG_BLK_DEV_IDESCSI is not set
# CONFIG_IDE_TASK_IOCTL is not set
# CONFIG_BLK_DEV_CMD640 is not set
# CONFIG_BLK_DEV_CMD640_ENHANCED is not set
# CONFIG_BLK_DEV_ISAPNP is not set
# CONFIG_BLK_DEV_RZ1000 is not set
CONFIG_BLK_DEV_IDEPCI=y
CONFIG_IDEPCI_SHARE_IRQ=y
CONFIG_BLK_DEV_IDEDMA_PCI=y
# CONFIG_BLK_DEV_OFFBOARD is not set
# CONFIG_BLK_DEV_IDEDMA_FORCED is not set
CONFIG_IDEDMA_PCI_AUTO=y
# CONFIG_IDEDMA_ONLYDISK is not set
CONFIG_BLK_DEV_IDEDMA=y
# CONFIG_IDEDMA_PCI_WIP is not set
# CONFIG_BLK_DEV_IDEDMA_TIMEOUT is not set
# CONFIG_IDEDMA_NEW_DRIVE_LISTINGS is not set
CONFIG_BLK_DEV_ADMA=y
# CONFIG_BLK_DEV_AEC62XX is not set
# CONFIG_AEC62XX_TUNING is not set
# CONFIG_BLK_DEV_ALI15X3 is not set
# CONFIG_WDC_ALI15X3 is not set
# CONFIG_BLK_DEV_AMD74XX is not set
# CONFIG_AMD74XX_OVERRIDE is not set
# CONFIG_BLK_DEV_CMD64X is not set
# CONFIG_BLK_DEV_CMD680 is not set
# CONFIG_BLK_DEV_CY82C693 is not set
# CONFIG_BLK_DEV_CS5530 is not set
# CONFIG_BLK_DEV_HPT34X is not set
# CONFIG_HPT34X_AUTODMA is not set
# CONFIG_BLK_DEV_HPT366 is not set
# CONFIG_BLK_DEV_PIIX is not set
# CONFIG_PIIX_TUNING is not set
# CONFIG_BLK_DEV_NS87415 is not set
# CONFIG_BLK_DEV_OPTI621 is not set
# CONFIG_BLK_DEV_PDC202XX is not set
# CONFIG_PDC202XX_BURST is not set
# CONFIG_PDC202XX_FORCE is not set
# CONFIG_BLK_DEV_SVWKS is not set
CONFIG_BLK_DEV_SIS5513=y
# CONFIG_BLK_DEV_SLC90E66 is not set
# CONFIG_BLK_DEV_TRM290 is not set
# CONFIG_BLK_DEV_VIA82CXXX is not set
# CONFIG_IDE_CHIPSETS is not set
CONFIG_IDEDMA_AUTO=y
# CONFIG_IDEDMA_IVB is not set
# CONFIG_DMA_NONPCI is not set
CONFIG_BLK_DEV_IDE_MODES=y
# CONFIG_BLK_DEV_ATARAID is not set
# CONFIG_BLK_DEV_ATARAID_PDC is not set
# CONFIG_BLK_DEV_ATARAID_HPT is not set
#
# SCSI support
#
# CONFIG_SCSI is not set
#
# Fusion MPT device support
#
# CONFIG_FUSION is not set
# CONFIG_FUSION_BOOT is not set
# CONFIG_FUSION_ISENSE is not set
# CONFIG_FUSION_CTL is not set
# CONFIG_FUSION_LAN is not set
#
# IEEE 1394 (FireWire) support (EXPERIMENTAL)
#
# CONFIG_IEEE1394 is not set
#
# I2O device support
#
# CONFIG_I2O is not set
# CONFIG_I2O_PCI is not set
# CONFIG_I2O_BLOCK is not set
# CONFIG_I2O_LAN is not set
# CONFIG_I2O_SCSI is not set
# CONFIG_I2O_PROC is not set
#
# Network device support
#
CONFIG_NETDEVICES=y
#
# ARCnet devices
#
# CONFIG_ARCNET is not set
# CONFIG_DUMMY is not set
# CONFIG_BONDING is not set
# CONFIG_EQUALIZER is not set
# CONFIG_TUN is not set
# CONFIG_ETHERTAP is not set
#
# Ethernet (10 or 100Mbit)
#
CONFIG_NET_ETHERNET=y
# CONFIG_SUNLANCE is not set
# CONFIG_HAPPYMEAL is not set
# CONFIG_SUNBMAC is not set
# CONFIG_SUNQE is not set
# CONFIG_SUNGEM is not set
# CONFIG_NET_VENDOR_3COM is not set
# CONFIG_LANCE is not set
# CONFIG_NET_VENDOR_SMC is not set
# CONFIG_NET_VENDOR_RACAL is not set
# CONFIG_AT1700 is not set
# CONFIG_DEPCA is not set
# CONFIG_HP100 is not set
# CONFIG_NET_ISA is not set
CONFIG_NET_PCI=y
# CONFIG_PCNET32 is not set
# CONFIG_ADAPTEC_STARFIRE is not set
# CONFIG_AC3200 is not set
# CONFIG_APRICOT is not set
# CONFIG_CS89x0 is not set
# CONFIG_TULIP is not set
# CONFIG_DE4X5 is not set
# CONFIG_DGRS is not set
# CONFIG_DM9102 is not set
# CONFIG_EEPRO100 is not set
# CONFIG_E100 is not set
# CONFIG_LNE390 is not set
# CONFIG_FEALNX is not set
# CONFIG_NATSEMI is not set
# CONFIG_NE2K_PCI is not set
# CONFIG_NE3210 is not set
# CONFIG_ES3210 is not set
# CONFIG_8139CP is not set
# CONFIG_8139TOO is not set
# CONFIG_8139TOO_PIO is not set
# CONFIG_8139TOO_TUNE_TWISTER is not set
# CONFIG_8139TOO_8129 is not set
# CONFIG_8139_OLD_RX_RESET is not set
CONFIG_SIS900=y
# CONFIG_EPIC100 is not set
# CONFIG_SUNDANCE is not set
# CONFIG_TLAN is not set
# CONFIG_TC35815 is not set
# CONFIG_VIA_RHINE is not set
# CONFIG_VIA_RHINE_MMIO is not set
# CONFIG_WINBOND_840 is not set
# CONFIG_NET_POCKET is not set
#
# Ethernet (1000 Mbit)
#
# CONFIG_ACENIC is not set
# CONFIG_DL2K is not set
# CONFIG_E1000 is not set
# CONFIG_MYRI_SBUS is not set
# CONFIG_NS83820 is not set
# CONFIG_HAMACHI is not set
# CONFIG_YELLOWFIN is not set
# CONFIG_SK98LIN is not set
# CONFIG_TIGON3 is not set
# CONFIG_FDDI is not set
# CONFIG_HIPPI is not set
# CONFIG_PLIP is not set
# CONFIG_PPP is not set
# CONFIG_SLIP is not set
#
# Wireless LAN (non-hamradio)
#
# CONFIG_NET_RADIO is not set
#
# Token Ring devices
#
# CONFIG_TR is not set
# CONFIG_NET_FC is not set
# CONFIG_RCPCI is not set
# CONFIG_SHAPER is not set
#
# Wan interfaces
#
# CONFIG_WAN is not set
#
# Amateur Radio support
#
# CONFIG_HAMRADIO is not set
#
# IrDA (infrared) support
#
# CONFIG_IRDA is not set
#
# ISDN subsystem
#
# CONFIG_ISDN is not set
#
# Old CD-ROM drivers (not SCSI, not IDE)
#
# CONFIG_CD_NO_IDESCSI is not set
#
# Input core support
#
# CONFIG_INPUT is not set
# CONFIG_INPUT_KEYBDEV is not set
# CONFIG_INPUT_MOUSEDEV is not set
# CONFIG_INPUT_JOYDEV is not set
# CONFIG_INPUT_EVDEV is not set
#
# Character devices
#
CONFIG_VT=y
CONFIG_VT_CONSOLE=y
CONFIG_SERIAL=y
# CONFIG_SERIAL_CONSOLE is not set
# CONFIG_SERIAL_EXTENDED is not set
# CONFIG_SERIAL_NONSTANDARD is not set
CONFIG_UNIX98_PTYS=y
CONFIG_UNIX98_PTY_COUNT=256
#
# I2C support
#
# CONFIG_I2C is not set
#
# Mice
#
# CONFIG_BUSMOUSE is not set
# CONFIG_MOUSE is not set
#
# Joysticks
#
# CONFIG_INPUT_GAMEPORT is not set
# CONFIG_QIC02_TAPE is not set
#
# Watchdog Cards
#
# CONFIG_WATCHDOG is not set
# CONFIG_AMD_RNG is not set
# CONFIG_INTEL_RNG is not set
# CONFIG_NVRAM is not set
CONFIG_RTC=y
# CONFIG_DTLK is not set
# CONFIG_R3964 is not set
# CONFIG_APPLICOM is not set
# CONFIG_SONYPI is not set
#
# Ftape, the floppy tape device driver
#
# CONFIG_FTAPE is not set
CONFIG_AGP=y
# CONFIG_AGP_INTEL is not set
# CONFIG_AGP_I810 is not set
# CONFIG_AGP_VIA is not set
# CONFIG_AGP_AMD is not set
CONFIG_AGP_SIS=y
# CONFIG_AGP_ALI is not set
# CONFIG_AGP_SWORKS is not set
# CONFIG_DRM is not set
# CONFIG_MWAVE is not set
#
# Multimedia devices
#
# CONFIG_VIDEO_DEV is not set
#
# File systems
#
# CONFIG_QUOTA is not set
# CONFIG_AUTOFS_FS is not set
CONFIG_AUTOFS4_FS=y
CONFIG_REISERFS_FS=y
# CONFIG_REISERFS_CHECK is not set
# CONFIG_REISERFS_PROC_INFO is not set
# CONFIG_ADFS_FS is not set
# CONFIG_ADFS_FS_RW is not set
# CONFIG_AFFS_FS is not set
# CONFIG_HFS_FS is not set
# CONFIG_BEFS_FS is not set
# CONFIG_BEFS_DEBUG is not set
# CONFIG_BFS_FS is not set
CONFIG_EXT3_FS=y
CONFIG_JBD=y
# CONFIG_JBD_DEBUG is not set
CONFIG_FAT_FS=y
CONFIG_MSDOS_FS=y
CONFIG_UMSDOS_FS=y
CONFIG_VFAT_FS=y
# CONFIG_EFS_FS is not set
# CONFIG_JFFS_FS is not set
# CONFIG_JFFS2_FS is not set
# CONFIG_CRAMFS is not set
CONFIG_TMPFS=y
CONFIG_RAMFS=y
CONFIG_ISO9660_FS=y
CONFIG_JOLIET=y
CONFIG_ZISOFS=y
CONFIG_MINIX_FS=y
# CONFIG_VXFS_FS is not set
# CONFIG_NTFS_FS is not set
# CONFIG_NTFS_RW is not set
# CONFIG_HPFS_FS is not set
CONFIG_PROC_FS=y
# CONFIG_DEVFS_FS is not set
# CONFIG_DEVFS_MOUNT is not set
# CONFIG_DEVFS_DEBUG is not set
CONFIG_DEVPTS_FS=y
# CONFIG_QNX4FS_FS is not set
# CONFIG_QNX4FS_RW is not set
# CONFIG_ROMFS_FS is not set
CONFIG_EXT2_FS=y
# CONFIG_SYSV_FS is not set
# CONFIG_UDF_FS is not set
# CONFIG_UDF_RW is not set
# CONFIG_UFS_FS is not set
# CONFIG_UFS_FS_WRITE is not set
#
# Network File Systems
#
# CONFIG_CODA_FS is not set
# CONFIG_INTERMEZZO_FS is not set
CONFIG_NFS_FS=y
# CONFIG_NFS_V3 is not set
# CONFIG_ROOT_NFS is not set
CONFIG_NFSD=y
# CONFIG_NFSD_V3 is not set
# CONFIG_NFSD_TCP is not set
CONFIG_SUNRPC=y
CONFIG_LOCKD=y
CONFIG_SMB_FS=y
# CONFIG_SMB_NLS_DEFAULT is not set
# CONFIG_NCP_FS is not set
# CONFIG_NCPFS_PACKET_SIGNING is not set
# CONFIG_NCPFS_IOCTL_LOCKING is not set
# CONFIG_NCPFS_STRONG is not set
# CONFIG_NCPFS_NFS_NS is not set
# CONFIG_NCPFS_OS2_NS is not set
# CONFIG_NCPFS_SMALLDOS is not set
# CONFIG_NCPFS_NLS is not set
# CONFIG_NCPFS_EXTRAS is not set
CONFIG_ZISOFS_FS=y
#
# Partition Types
#
# CONFIG_PARTITION_ADVANCED is not set
CONFIG_MSDOS_PARTITION=y
CONFIG_SMB_NLS=y
CONFIG_NLS=y
#
# Native Language Support
#
CONFIG_NLS_DEFAULT="iso8859-1"
CONFIG_NLS_CODEPAGE_437=y
# CONFIG_NLS_CODEPAGE_737 is not set
# CONFIG_NLS_CODEPAGE_775 is not set
# CONFIG_NLS_CODEPAGE_850 is not set
# CONFIG_NLS_CODEPAGE_852 is not set
# CONFIG_NLS_CODEPAGE_855 is not set
# CONFIG_NLS_CODEPAGE_857 is not set
CONFIG_NLS_CODEPAGE_860=y
# CONFIG_NLS_CODEPAGE_861 is not set
# CONFIG_NLS_CODEPAGE_862 is not set
# CONFIG_NLS_CODEPAGE_863 is not set
# CONFIG_NLS_CODEPAGE_864 is not set
# CONFIG_NLS_CODEPAGE_865 is not set
# CONFIG_NLS_CODEPAGE_866 is not set
# CONFIG_NLS_CODEPAGE_869 is not set
# CONFIG_NLS_CODEPAGE_936 is not set
# CONFIG_NLS_CODEPAGE_950 is not set
# CONFIG_NLS_CODEPAGE_932 is not set
# CONFIG_NLS_CODEPAGE_949 is not set
# CONFIG_NLS_CODEPAGE_874 is not set
# CONFIG_NLS_ISO8859_8 is not set
# CONFIG_NLS_CODEPAGE_1250 is not set
# CONFIG_NLS_CODEPAGE_1251 is not set
CONFIG_NLS_ISO8859_1=y
# CONFIG_NLS_ISO8859_2 is not set
# CONFIG_NLS_ISO8859_3 is not set
# CONFIG_NLS_ISO8859_4 is not set
# CONFIG_NLS_ISO8859_5 is not set
# CONFIG_NLS_ISO8859_6 is not set
# CONFIG_NLS_ISO8859_7 is not set
# CONFIG_NLS_ISO8859_9 is not set
# CONFIG_NLS_ISO8859_13 is not set
# CONFIG_NLS_ISO8859_14 is not set
# CONFIG_NLS_ISO8859_15 is not set
# CONFIG_NLS_KOI8_R is not set
# CONFIG_NLS_KOI8_U is not set
# CONFIG_NLS_UTF8 is not set
#
# Console drivers
#
CONFIG_VGA_CONSOLE=y
# CONFIG_VIDEO_SELECT is not set
# CONFIG_MDA_CONSOLE is not set
#
# Frame-buffer support
#
# CONFIG_FB is not set
#
# Sound
#
CONFIG_SOUND=y
# CONFIG_SOUND_ALI5455 is not set
# CONFIG_SOUND_BT878 is not set
# CONFIG_SOUND_CMPCI is not set
# CONFIG_SOUND_EMU10K1 is not set
# CONFIG_MIDI_EMU10K1 is not set
# CONFIG_SOUND_FUSION is not set
# CONFIG_SOUND_CS4281 is not set
# CONFIG_SOUND_ES1370 is not set
# CONFIG_SOUND_ES1371 is not set
# CONFIG_SOUND_ESSSOLO1 is not set
# CONFIG_SOUND_MAESTRO is not set
# CONFIG_SOUND_MAESTRO3 is not set
# CONFIG_SOUND_ICH is not set
# CONFIG_SOUND_RME96XX is not set
# CONFIG_SOUND_SONICVIBES is not set
CONFIG_SOUND_TRIDENT=y
# CONFIG_SOUND_MSNDCLAS is not set
# CONFIG_SOUND_MSNDPIN is not set
# CONFIG_SOUND_VIA82CXXX is not set
# CONFIG_MIDI_VIA82CXXX is not set
# CONFIG_SOUND_OSS is not set
# CONFIG_SOUND_TVMIXER is not set
#
# USB support
#
# CONFIG_USB is not set
#
# Bluetooth support
#
# CONFIG_BLUEZ is not set
#
# Kernel hacking
#
# CONFIG_DEBUG_KERNEL is not set
#
# Library routines
#
CONFIG_ZLIB_INFLATE=y
# CONFIG_ZLIB_DEFLATE is not set
^ permalink raw reply [flat|nested] 13+ messages in thread
* Re: 2.4.20-pre3 boot hang
2002-08-19 11:13 ` Mauricio Pretto
@ 2002-08-19 11:38 ` Skidley
2002-08-19 12:40 ` Mauricio Pretto
0 siblings, 1 reply; 13+ messages in thread
From: Skidley @ 2002-08-19 11:38 UTC (permalink / raw)
To: Mauricio Pretto; +Cc: linux-kernel
On Mon, Aug 19, 2002 at 08:13:31AM -0300, Mauricio Pretto wrote:
> Same Problem Here, athlon 1.1 , Right after Rt netlink socket it hangs.
> My .config goes attach.
>
>
> Klaus Dittrich wrote:
>
> >SMP, P-III, Intel-BX
> >
> >booting Linux 2.4.20-pre3 stops after
> >
> >Linux NET4.0 for Linux 2.4
> >Based upon Swansea University Computer Society NET3.039
> >Initializing RT netlink socket
> >
> >
>
>
> --
> Mauricio Pretto
> Gerente de Produtos
> Interage Integradora
> http://www.interage.com.br
>
> T?cnico Certificado Conectiva Linux
This patch was posted to lkml earlier, it fixed the same problem for me:
diff -urN linux-2.4/kernel/sched.c pmac/kernel/sched.c
--- linux-2.4/kernel/sched.c Wed Aug 7 18:10:01 2002
+++ pmac/kernel/sched.c Mon Aug 19 10:39:39 2002
@@ -1081,6 +1081,7 @@
{
set_current_state(TASK_RUNNING);
sys_sched_yield();
+ schedule();
}
void __cond_resched(void)
--
"I mean they are gonna kill ya so like if ya give em a quick, short, sharp,
shock they won't do it again. Dig it! I mean he got off lightly cuz I would
have given him a thrashing. I only hit him once. It was only a difference of
opinion but really... I mean good manners don't cost nothin do they. Eh?"
^ permalink raw reply [flat|nested] 13+ messages in thread
* Re: 2.4.20-pre3 boot hang
2002-08-19 7:57 ` Markus Plail
@ 2002-08-19 12:18 ` Alan Cox
2002-08-19 12:46 ` Markus Plail
0 siblings, 1 reply; 13+ messages in thread
From: Alan Cox @ 2002-08-19 12:18 UTC (permalink / raw)
To: Markus Plail; +Cc: linux mailing-list
On Mon, 2002-08-19 at 08:57, Markus Plail wrote:
> >Oops log, dmesg boot log of 2.4.18 and 2.4.20pre2-ac3 ?
>
> Here it comes. I tried ac4 this morning and it's still the same.
Ok thanks. That one does tell me something useful. The scsi layer (most
likely ide-scsi itself) passed down a buffer that did not have a valid
mapping.
Do you have Highmem/highio enabled ?
^ permalink raw reply [flat|nested] 13+ messages in thread
* Re: 2.4.20-pre3 boot hang
2002-08-19 11:38 ` Skidley
@ 2002-08-19 12:40 ` Mauricio Pretto
0 siblings, 0 replies; 13+ messages in thread
From: Mauricio Pretto @ 2002-08-19 12:40 UTC (permalink / raw)
Cc: linux-kernel
Ok It worked Here, Boots Ok.
Thanks
Skidley wrote:
> On Mon, Aug 19, 2002 at 08:13:31AM -0300, Mauricio Pretto wrote:
>
>>Same Problem Here, athlon 1.1 , Right after Rt netlink socket it hangs.
>>My .config goes attach.
>>
>>
>>Klaus Dittrich wrote:
>>
>>
>>>SMP, P-III, Intel-BX
>>>
>>>booting Linux 2.4.20-pre3 stops after
>>>
>>>Linux NET4.0 for Linux 2.4
>>>Based upon Swansea University Computer Society NET3.039
>>>Initializing RT netlink socket
>>>
>>>
>>>
>>
>>--
>>Mauricio Pretto
>>Gerente de Produtos
>>Interage Integradora
>>http://www.interage.com.br
>>
>>T?cnico Certificado Conectiva Linux
>>
>
> This patch was posted to lkml earlier, it fixed the same problem for me:
>
>
> diff -urN linux-2.4/kernel/sched.c pmac/kernel/sched.c
> --- linux-2.4/kernel/sched.c Wed Aug 7 18:10:01 2002
> +++ pmac/kernel/sched.c Mon Aug 19 10:39:39 2002
> @@ -1081,6 +1081,7 @@
> {
> set_current_state(TASK_RUNNING);
> sys_sched_yield();
> + schedule();
> }
>
> void __cond_resched(void)
>
>
--
Mauricio Pretto
Gerente de Produtos
Interage Integradora
http://www.interage.com.br
Técnico Certificado Conectiva Linux
^ permalink raw reply [flat|nested] 13+ messages in thread
* Re: 2.4.20-pre3 boot hang
2002-08-19 12:18 ` Alan Cox
@ 2002-08-19 12:46 ` Markus Plail
0 siblings, 0 replies; 13+ messages in thread
From: Markus Plail @ 2002-08-19 12:46 UTC (permalink / raw)
To: linux mailing-list
Hi Alan!
* Alan Cox writes:
>Ok thanks. That one does tell me something useful. The scsi layer (most
>likely ide-scsi itself) passed down a buffer that did not have a valid
>mapping.
>Do you have Highmem/highio enabled ?
Nope, neither of them.
regards
Markus
^ permalink raw reply [flat|nested] 13+ messages in thread
* 2.4.20-pre3 boot hang
@ 2002-08-19 17:32 Klaus Dittrich
0 siblings, 0 replies; 13+ messages in thread
From: Klaus Dittrich @ 2002-08-19 17:32 UTC (permalink / raw)
To: linux mailing-list
Thanks for the patch Sikdley, it works here too.
--
Regards Klaus
^ permalink raw reply [flat|nested] 13+ messages in thread
end of thread, other threads:[~2002-08-19 17:30 UTC | newest]
Thread overview: 13+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
2002-08-18 15:31 2.4.20-pre3 boot hang Klaus Dittrich
2002-08-18 18:06 ` Markus Plail
2002-08-18 18:22 ` Alan Cox
2002-08-19 7:57 ` Markus Plail
2002-08-19 12:18 ` Alan Cox
2002-08-19 12:46 ` Markus Plail
2002-08-18 18:42 ` Erik Andersen
2002-08-18 20:03 ` Andre Hedrick
2002-08-18 20:18 ` Erik Andersen
2002-08-19 11:13 ` Mauricio Pretto
2002-08-19 11:38 ` Skidley
2002-08-19 12:40 ` Mauricio Pretto
-- strict thread matches above, loose matches on Subject: below --
2002-08-19 17:32 Klaus Dittrich
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox