* Oops (ide?) with 2.4.20-pre8-ac3 at boot on scsi only smp
@ 2002-10-02 4:01 lists
2002-10-04 1:44 ` lists
0 siblings, 1 reply; 3+ messages in thread
From: lists @ 2002-10-02 4:01 UTC (permalink / raw)
To: linux-kernel
hi,
First report - please let me know what more
I can do to help.
gene/
(0) 2.4.20-pre8-ac3 - oops at boot - scsi disks only -
no IDE disks - smp.
(1) Fresh build of 2.4.20-pre8-ac3 - aic7xxx driver in kernel -
oops'es at boot in IDE code with 'Unable to handle kernel NULL pointer'
Does have IDE cdrom and CDRW (latter booted with ide-scsi)
Machine is dual P4 with 1 Gb memory and kernel compiled with 4Gb memory
model. Runs fine under stock redhat 2.4.18-10 kernel
------------------------------------------------------------------------
(2) Oops: (hand entered)
ksymoops 2.4.6 on i686 2.4.18-10smp. Options used
-v /boot/2.4/2.4.20-pre8-ac3/vmlinux (specified)
-K (specified)
-L (specified)
-o /lib/modules/2.4.20-pre8-ac3/ (specified)
-m /boot/2.4/2.4.20-pre8-ac3/System.map (specified)
No modules in ksyms, skipping objects
ide1: BM-DMA at 0xffa8-0xffaf<1> Unable to handle kernel NULL pointer
c01baa84
*pde = 00000000
Oops: 0000
CPU: 0
EIP: 0010:[<c01baa84>] Not tainted
Using defaults from ksymoops -t elf32-i386 -a i386
EFLAGS: 00010202
eax: 00000000 ebx: c039c6e0 ecx: c36944cc edx: c02b87d4
esi: c039c6cc edi: 0000ffa8 ebp: 00000000 esp: c34abedc
ds: 0018 es: 0018 ss: 0018
Process swapper (pid: 1, stackpage=c34ab000)
Stack: 00000008 c039c6cc c3694400 c02b87d4 c01bab46 c039c6cc 0000ffa8 00000008
0000ffa8 c039c6cc c0303b81 c039c6cc 0000ffa8 00000008 c01b9356 c039c6cc
0000ffa8 000587f5 c039c6cc c02b87f5 c03901f0 c02b87d4 c01b96c6 c3694400
Call Trace: [<c01bab46>] [<c01b9356>] [<c01b96c6>] [<c01b9737>] [<c01a51d5>]
[<c0105000>] [<c0105078>] [<c0105000>] [<c01071f6>] [<c0105050>]
Code: 8b 80 3c 04 00 00 eb 06 8d 74 26 00 89 f8 89 86 38 04 00 00
>>EIP; c01baa84 <ide_iomio_dma+a4/110> <=====
>>ebx; c039c6e0 <ide_hwifs+480/2c38>
>>edx; c02b87d4 <piix_pci_info+1e0/330>
>>esi; c039c6cc <ide_hwifs+46c/2c38>
Trace; c01bab46 <ide_setup_dma+16/2a0>
Trace; c01b9356 <ide_hwif_setup_dma+b6/f0>
Trace; c01b96c6 <do_ide_setup_pci_device+236/290>
Trace; c01b9737 <ide_setup_pci_device+17/20>
Trace; c01a51d5 <piix_init_one+35/40>
Trace; c0105000 <_stext+0/0>
Trace; c0105078 <init+28/190>
Trace; c0105000 <_stext+0/0>
Trace; c01071f6 <kernel_thread+26/30>
Trace; c0105050 <init+0/190>
Code; c01baa84 <ide_iomio_dma+a4/110>
00000000 <_EIP>:
Code; c01baa84 <ide_iomio_dma+a4/110> <=====
0: 8b 80 3c 04 00 00 mov 0x43c(%eax),%eax <=====
Code; c01baa8a <ide_iomio_dma+aa/110>
6: eb 06 jmp e <_EIP+0xe> c01baa92 <ide_iomio_dma+b2/110>
Code; c01baa8c <ide_iomio_dma+ac/110>
8: 8d 74 26 00 lea 0x0(%esi,1),%esi
Code; c01baa90 <ide_iomio_dma+b0/110>
c: 89 f8 mov %edi,%eax
Code; c01baa92 <ide_iomio_dma+b2/110>
e: 89 86 38 04 00 00 mov %eax,0x438(%esi)
<0>Kernel panic: Attempted to kill init!
------------------------------------------------------------------------
(3) ver_linux:
Linux flash 2.4.18-10smp #1 SMP Wed Aug 7 11:17:48 EDT 2002 i686 unknown
Gnu C 2.96
Gnu make 3.79.1
util-linux 2.11n
mount 2.11n
modutils 2.4.14
e2fsprogs 1.27
jfsutils 1.0.17
reiserfsprogs 3.x.0j
pcmcia-cs 3.1.22
PPP 2.4.1
isdn4k-utils 3.1pre1
Linux C Library 2.2.5
Dynamic linker (ldd) 2.2.5
Procps 2.0.7
Net-tools 1.60
Console-tools 0.3.3
Sh-utils 2.0.11
Modules Loaded nfs lockd sunrpc sr_mod emu10k1 sound ac97_codec soundcore radeon agpgart parport_pc lp parport binfmt_misc autofs 3c59x ide-scsi ide-cd cdrom mousedev hid input usb-uhci usbcore ext3 jbd aic7xxx sd_mod scsi_mod
------------------------------------------------------------------------
4) cat /proc/cpuinfo
processor : 0
vendor_id : GenuineIntel
cpu family : 15
model : 1
model name : Intel(R) Xeon(TM) CPU 1.70GHz
stepping : 2
cpu MHz : 1694.897
cache size : 256 KB
fdiv_bug : no
hlt_bug : no
f00f_bug : no
coma_bug : no
fpu : yes
fpu_exception : yes
cpuid level : 2
wp : yes
flags : fpu vme de pse tsc msr pae mce cx8 apic sep mtrr pge mca cmov pat pse36 clflush dts acpi mmx fxsr sse sse2 ss ht tm
bogomips : 3381.65
processor : 1
vendor_id : GenuineIntel
cpu family : 15
model : 1
model name : Intel(R) Xeon(TM) CPU 1.70GHz
stepping : 2
cpu MHz : 1694.897
cache size : 256 KB
fdiv_bug : no
hlt_bug : no
f00f_bug : no
coma_bug : no
fpu : yes
fpu_exception : yes
cpuid level : 2
wp : yes
flags : fpu vme de pse tsc msr pae mce cx8 apic sep mtrr pge mca cmov pat pse36 clflush dts acpi mmx fxsr sse sse2 ss ht tm
bogomips : 3381.65
------------------------------------------------------------------------
5) lspci -vvv
00:00.0 Host bridge: Intel Corp. 82850 860 (Wombat) Chipset Host Bridge (MCH) (rev 04)
Subsystem: Dell Computer Corporation: Unknown device 00d8
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ >SERR- <PERR+
Latency: 0
Region 0: Memory at e8000000 (32-bit, prefetchable) [size=128M]
Capabilities: [a0] AGP version 2.0
Status: RQ=31 SBA+ 64bit- FW+ Rate=x1,x2
Command: RQ=0 SBA+ AGP+ 64bit- FW- Rate=x1
00:01.0 PCI bridge: Intel Corp. 82850 850 (Tehama) Chipset AGP Bridge (rev 04) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap- 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64
Bus: primary=00, secondary=01, subordinate=01, sec-latency=64
I/O behind bridge: 0000e000-0000efff
Memory behind bridge: ff800000-ff9fffff
Prefetchable memory behind bridge: f0000000-f7ffffff
BridgeCtl: Parity- SERR+ NoISA+ VGA+ MAbort- >Reset- FastB2B-
00:02.0 PCI bridge: Intel Corp. 82860 860 (Wombat) Chipset AGP Bridge (rev 04) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap- 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64
Bus: primary=00, secondary=02, subordinate=03, sec-latency=0
I/O behind bridge: 0000d000-0000dfff
Memory behind bridge: ff500000-ff7fffff
Prefetchable memory behind bridge: fff00000-000fffff
BridgeCtl: Parity- SERR+ NoISA+ VGA- MAbort- >Reset- FastB2B-
00:1e.0 PCI bridge: Intel Corp. 82801BA/CA PCI Bridge (rev 04) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Bus: primary=00, secondary=04, subordinate=04, sec-latency=64
I/O behind bridge: 0000c000-0000cfff
Memory behind bridge: ff300000-ff4fffff
Prefetchable memory behind bridge: fff00000-000fffff
BridgeCtl: Parity- SERR+ NoISA+ VGA- MAbort- >Reset- FastB2B-
00:1f.0 ISA bridge: Intel Corp. 82801BA ISA Bridge (LPC) (rev 04)
Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
00:1f.1 IDE interface: Intel Corp. 82801BA IDE U100 (rev 04) (prog-if 80 [Master])
Subsystem: Dell Computer Corporation: Unknown device 00d8
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Region 4: I/O ports at ffa0 [size=16]
00:1f.2 USB Controller: Intel Corp. 82801BA/BAM USB (Hub (rev 04) (prog-if 00 [UHCI])
Subsystem: Dell Computer Corporation: Unknown device 00d8
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin D routed to IRQ 19
Region 4: I/O ports at ff80 [size=32]
00:1f.3 SMBus: Intel Corp. 82801BA/BAM SMBus (rev 04)
Subsystem: Dell Computer Corporation: Unknown device 00d8
Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin B routed to IRQ 17
Region 4: I/O ports at bcd0 [size=16]
00:1f.4 USB Controller: Intel Corp. 82801BA/BAM USB (Hub (rev 04) (prog-if 00 [UHCI])
Subsystem: Dell Computer Corporation: Unknown device 00d8
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin C routed to IRQ 23
Region 4: I/O ports at ff60 [size=32]
01:00.0 VGA compatible controller: ATI Technologies Inc Radeon VE QY (prog-if 00 [VGA])
Subsystem: ATI Technologies Inc: Unknown device 1b8a
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping+ SERR+ FastB2B-
Status: Cap+ 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (2000ns min), cache line size 10
Interrupt: pin A routed to IRQ 16
Region 0: Memory at f0000000 (32-bit, prefetchable) [size=128M]
Region 1: I/O ports at ec00 [size=256]
Region 2: Memory at ff8f0000 (32-bit, non-prefetchable) [size=64K]
Expansion ROM at c1000000 [disabled] [size=128K]
Capabilities: [58] AGP version 2.0
Status: RQ=47 SBA+ 64bit- FW- Rate=x1,x2
Command: RQ=31 SBA+ AGP+ 64bit- FW- Rate=x1
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
02:1f.0 PCI bridge: Intel Corp. 82806AA PCI64 Hub PCI Bridge (rev 03) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap- 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Bus: primary=02, secondary=03, subordinate=03, sec-latency=64
I/O behind bridge: 0000d000-0000dfff
Memory behind bridge: ff600000-ff7fffff
Prefetchable memory behind bridge: fff00000-000fffff
BridgeCtl: Parity- SERR+ NoISA+ VGA- MAbort- >Reset- FastB2B-
03:00.0 PIC: Intel Corp. 82806AA PCI64 Hub Advanced Programmable Interrupt Controller (rev 01) (prog-if 20 [IO(X)-APIC])
Subsystem: Intel Corp. 82806AA PCI64 Hub APIC
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Region 0: Memory at ff6ff000 (32-bit, non-prefetchable) [disabled] [size=4K]
03:0c.0 SCSI storage controller: Adaptec AIC-7892A U160/m (rev 02)
Subsystem: Adaptec 29160 Ultra160 SCSI Controller
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (10000ns min, 6250ns max), cache line size 10
Interrupt: pin A routed to IRQ 20
BIST result: 00
Region 0: I/O ports at dc00 [disabled] [size=256]
Region 1: Memory at ff6fe000 (64-bit, non-prefetchable) [size=4K]
Expansion ROM at ff700000 [disabled] [size=128K]
Capabilities: [dc] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
03:0e.0 SCSI storage controller: Adaptec AIC-7892P U160/m (rev 02)
Subsystem: Dell Computer Corporation: Unknown device 00d8
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (10000ns min, 6250ns max), cache line size 10
Interrupt: pin A routed to IRQ 22
BIST result: 00
Region 0: I/O ports at d800 [disabled] [size=256]
Region 1: Memory at ff6fd000 (64-bit, non-prefetchable) [size=4K]
Expansion ROM at ff700000 [disabled] [size=128K]
Capabilities: [dc] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
04:0b.0 Ethernet controller: 3Com Corporation 3c905C-TX/TX-M [Tornado] (rev 78)
Subsystem: Dell Computer Corporation: Unknown device 00d8
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (2500ns min, 2500ns max), cache line size 10
Interrupt: pin A routed to IRQ 23
Region 0: I/O ports at cc80 [size=128]
Region 1: Memory at ff3ffc00 (32-bit, non-prefetchable) [size=128]
Expansion ROM at ff400000 [disabled] [size=128K]
Capabilities: [dc] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=2 PME-
04:0c.0 FireWire (IEEE 1394): Texas Instruments TSB12LV26 IEEE-1394 Controller (Link) (prog-if 10 [OHCI])
Subsystem: Dell Computer Corporation: Unknown device 00d8
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (500ns min, 1000ns max), cache line size 10
Interrupt: pin A routed to IRQ 16
Region 0: Memory at ff3ff000 (32-bit, non-prefetchable) [size=2K]
Region 1: Memory at ff3f8000 (32-bit, non-prefetchable) [size=16K]
Capabilities: [44] Power Management version 1
Flags: PMEClk- DSI- D1- D2+ AuxCurrent=0mA PME(D0-,D1-,D2+,D3hot+,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
04:0e.0 Multimedia audio controller: Creative Labs SB Live! EMU10k1 (rev 08)
Subsystem: Creative Labs CT4780 SBLive! Value
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (500ns min, 5000ns max)
Interrupt: pin A routed to IRQ 18
Region 0: I/O ports at cc60 [size=32]
Capabilities: [dc] Power Management version 2
Flags: PMEClk- DSI+ D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
04:0e.1 Input device controller: Creative Labs SB Live! MIDI/Game Port (rev 08)
Subsystem: Creative Labs Gameport Joystick
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64
Region 0: I/O ports at cc58 [size=8]
Capabilities: [dc] Power Management version 2
Flags: PMEClk- DSI+ D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
------------------------------------------------------------------------
5) cat /proc/scsi/scsi
Attached devices:
Host: scsi1 Channel: 00 Id: 00 Lun: 00
Vendor: FUJITSU Model: MAM3184MP Rev: 5A01
Type: Direct-Access ANSI SCSI revision: 03
Host: scsi1 Channel: 00 Id: 01 Lun: 00
Vendor: FUJITSU Model: MAM3184MP Rev: 5A01
Type: Direct-Access ANSI SCSI revision: 03
Host: scsi2 Channel: 00 Id: 00 Lun: 00
Vendor: _NEC Model: NR-7800A Rev: 1.0B
Type: CD-ROM ANSI SCSI revision: 02
------------------------------------------------------------------------
^ permalink raw reply [flat|nested] 3+ messages in thread* Re: Oops (ide?) with 2.4.20-pre8-ac3 at boot on scsi only smp
2002-10-02 4:01 Oops (ide?) with 2.4.20-pre8-ac3 at boot on scsi only smp lists
@ 2002-10-04 1:44 ` lists
2002-10-05 2:38 ` lists
0 siblings, 1 reply; 3+ messages in thread
From: lists @ 2002-10-04 1:44 UTC (permalink / raw)
To: linux-kernel
Here are the things I tried to see if I could make headway - none
helped - still OOPS at boot:
o Compiled with no highmem -
o Compiled without SMP
o removed hdd=ide-scsi boot option
o added ide0=nodma ide1=nodma boot option
o switched to aic7xxx as a module using initrd
Still crashes - any suggestions on what I should try next?
Thanks,
gene/
On Wed, Oct 02, 2002 at 12:01:35AM -0400, lists@sapience.com wrote:
>
>
> hi,
>
> First report - please let me know what more
> I can do to help.
>
> gene/
>
>
> (0) 2.4.20-pre8-ac3 - oops at boot - scsi disks only -
> no IDE disks - smp.
>
> (1) Fresh build of 2.4.20-pre8-ac3 - aic7xxx driver in kernel -
> oops'es at boot in IDE code with 'Unable to handle kernel NULL pointer'
> Does have IDE cdrom and CDRW (latter booted with ide-scsi)
>
> Machine is dual P4 with 1 Gb memory and kernel compiled with 4Gb memory
> model. Runs fine under stock redhat 2.4.18-10 kernel
>
^ permalink raw reply [flat|nested] 3+ messages in thread* Re: Oops (ide?) with 2.4.20-pre8-ac3 at boot on scsi only smp
2002-10-04 1:44 ` lists
@ 2002-10-05 2:38 ` lists
0 siblings, 0 replies; 3+ messages in thread
From: lists @ 2002-10-05 2:38 UTC (permalink / raw)
To: linux-kernel
I have more info - 2.4.20-pre9 boots no problem - so whatever the
problem is it is _only_ in the -ac kernel. (2.4.18 is also fine)
I'd be happy to do further testing should anyone need it.
Regards,
gene/
On Thu, Oct 03, 2002 at 09:44:39PM -0400, lists@sapience.com wrote:
>
> Here are the things I tried to see if I could make headway - none
> helped - still OOPS at boot:
>
^ permalink raw reply [flat|nested] 3+ messages in thread
end of thread, other threads:[~2002-10-05 2:33 UTC | newest]
Thread overview: 3+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
2002-10-02 4:01 Oops (ide?) with 2.4.20-pre8-ac3 at boot on scsi only smp lists
2002-10-04 1:44 ` lists
2002-10-05 2:38 ` lists
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox