From: Jan Dittmer <jan@jandittmer.de>
To: linux-kernel@vger.kernel.org
Cc: linux-ide@vger.kernel.org
Subject: harddisk corruption with 2.5.41bk and tcq enabled
Date: Sat, 12 Oct 2002 10:50:01 +0200 [thread overview]
Message-ID: <200210121050.01471.jan@jandittmer.de> (raw)
Hi,
recent tcp additions seem to corrupt harddisk. X/KDE doesn't start up anymore
and 'mount' was broken after reboot. (Debian/unstable, ext3 fs) No Problem
with clean 2.5.41. Will try 2.5.42 now. You need any more information?
jan
Here goes dmesg/config output:
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
VP_IDE: IDE controller at PCI slot 00:07.1
VP_IDE: chipset revision 6
VP_IDE: not 100% native mode: will probe irqs later
VP_IDE: VIA vt82c686b (rev 40) IDE UDMA100 controller on pci00:07.1
ide0: BM-DMA at 0x9000-0x9007, BIOS settings: hda:DMA, hdb:pio
ide1: BM-DMA at 0x9008-0x900f, BIOS settings: hdc:DMA, hdd:DMA
hda: IC35L060AVVA07-0, ATA DISK drive
hda: DMA disabled
hda: bad special flag: 0x03
hda: tagged command queueing enabled, command queue depth 8
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
hdc: SONY CD-RW CRX175E2, ATAPI CD/DVD-ROM drive
hdd: Pioneer DVD-ROM ATAPIModel DVD-104S 012, ATAPI CD/DVD-ROM drive
hdc: DMA disabled
hdd: DMA disabled
ide1 at 0x170-0x177,0x376 on irq 15
hda: host protected area => 1
hda: 120103200 sectors (61493 MB) w/1863KiB Cache, CHS=7476/255/63, UDMA(100)
/dev/ide/host0/bus0/target0/lun0: p1 p2 p3 p4 < p5 p6 >
ide-cd: passing drive hdc to ide-scsi emulation.
hdd: ATAPI DVD-ROM drive, 512kB Cache, UDMA(33)
Uniform CD-ROM driver Revision: 3.12
SCSI subsystem driver Revision: 1.00
scsi0 : SCSI host adapter emulation for IDE ATAPI devices
Vendor: SONY Model: CD-RW CRX175E2 Rev: S002
Type: CD-ROM ANSI SCSI revision: 02
Attached scsi CD-ROM sr0 at scsi0, channel 0, id 0, lun 0
sr0: scsi3-mmc drive: 40x/40x writer cd/rw xa/form2 cdda tray
[...]
attempt to access beyond end of device
ide0(3,2): rw=0, want=1076371720, limit=19535040
attempt to access beyond end of device
ide0(3,2): rw=0, want=1076261672, limit=19535040
attempt to access beyond end of device
ide0(3,2): rw=0, want=1076240168, limit=19535040
attempt to access beyond end of device
ide0(3,2): rw=0, want=1076243240, limit=19535040
attempt to access beyond end of device
ide0(3,2): rw=0, want=1076335080, limit=19535040
attempt to access beyond end of device
ide0(3,2): rw=0, want=1076262568, limit=19535040
attempt to access beyond end of device
ide0(3,2): rw=0, want=1076262568, limit=19535040
attempt to access beyond end of device
ide0(3,2): rw=0, want=1076262568, limit=19535040
.config:
#
# IDE chipset support/bugfixes
#
# CONFIG_BLK_DEV_CMD640 is not set
# CONFIG_BLK_DEV_CMD640_ENHANCED is not set
# CONFIG_BLK_DEV_ISAPNP is not set
CONFIG_BLK_DEV_IDEPCI=y
# CONFIG_BLK_DEV_GENERIC is not set
CONFIG_IDEPCI_SHARE_IRQ=y
CONFIG_BLK_DEV_IDEDMA_PCI=y
CONFIG_BLK_DEV_IDE_TCQ=y
CONFIG_BLK_DEV_IDE_TCQ_DEFAULT=y
CONFIG_BLK_DEV_IDE_TCQ_DEPTH=8
# CONFIG_BLK_DEV_OFFBOARD is not set
CONFIG_BLK_DEV_IDEDMA_FORCED=y
CONFIG_IDEDMA_PCI_AUTO=y
# CONFIG_IDEDMA_ONLYDISK is not set
CONFIG_BLK_DEV_IDEDMA=y
CONFIG_IDEDMA_PCI_WIP=y
CONFIG_IDEDMA_NEW_DRIVE_LISTINGS=y
CONFIG_BLK_DEV_ADMA=y
# CONFIG_BLK_DEV_AEC62XX is not set
# CONFIG_BLK_DEV_ALI15X3 is not set
# CONFIG_WDC_ALI15X3 is not set
# CONFIG_BLK_DEV_AMD74XX is not set
# CONFIG_AMD74XX_OVERRIDE is not set
# CONFIG_BLK_DEV_CMD64X is not set
# CONFIG_BLK_DEV_CY82C693 is not set
# CONFIG_BLK_DEV_CS5530 is not set
# CONFIG_BLK_DEV_HPT34X is not set
# CONFIG_HPT34X_AUTODMA is not set
# CONFIG_BLK_DEV_HPT366 is not set
# CONFIG_BLK_DEV_PIIX is not set
# CONFIG_BLK_DEV_NFORCE is not set
# CONFIG_BLK_DEV_NS87415 is not set
# CONFIG_BLK_DEV_OPTI621 is not set
# CONFIG_BLK_DEV_PDC202XX_OLD is not set
# CONFIG_PDC202XX_BURST is not set
# CONFIG_BLK_DEV_PDC202XX_NEW is not set
# CONFIG_PDC202XX_FORCE is not set
# CONFIG_BLK_DEV_RZ1000 is not set
# CONFIG_BLK_DEV_SVWKS is not set
# CONFIG_BLK_DEV_SIIMAGE is not set
# CONFIG_BLK_DEV_SIS5513 is not set
# CONFIG_BLK_DEV_SLC90E66 is not set
# CONFIG_BLK_DEV_TRM290 is not set
CONFIG_BLK_DEV_VIA82CXXX=y
# CONFIG_IDE_CHIPSETS is not set
CONFIG_IDEDMA_AUTO=y
# CONFIG_IDEDMA_IVB is not set
# CONFIG_DMA_NONPCI is not set
CONFIG_BLK_DEV_IDE_MODES=y
next reply other threads:[~2002-10-12 8:42 UTC|newest]
Thread overview: 6+ messages / expand[flat|nested] mbox.gz Atom feed top
2002-10-12 8:50 Jan Dittmer [this message]
2002-10-12 9:06 ` harddisk corruption with 2.5.41bk and tcq enabled David S. Miller
2002-10-12 9:16 ` Jens Axboe
2002-10-12 11:37 ` Jan Dittmer
2002-10-13 23:30 ` Scott Henson
2002-10-12 18:40 ` Jan Dittmer
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=200210121050.01471.jan@jandittmer.de \
--to=jan@jandittmer.de \
--cc=linux-ide@vger.kernel.org \
--cc=linux-kernel@vger.kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox