2.5 BK boot hang after ide

2.5 BK boot hang after ide

[Duncan Sands]

Copied down by hand:

...
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
VP_IDE: IDE controller at PCI slot 00:11.1
ACPI: No IRQ known for interrupt pin A of device 00:11.1 - using IRQ 255
VP_IDE: Chipset revision 6
VP_IDE: not 100% native mode: will probe irqs later
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
VP_IDE: VIA vt 8235 (rev 00) IDE UDMA 133 controller on pci00:11.1
	ide0: BM_DMA at 0xfc00-0xfc07, BIOS settings: hda: DMA, hdb: DMA
	ide1: BM_DMA at 0xfc08-0xfc0f, BIOS settings: hdc: DMA, hdd: DMA
hda: ST320423A, ATA DISK drive
hdb: Maxtor 6E030L0, ATA DISK drive
id0 at 0x1f0-0x1f7, 0x3f6 on irq 14
hdc: TOSHIBA DVD-ROM SD-MI402, ATAPI CD/DVD-ROM drive
hdd: LG CD-RW CED-8080B, ATAPI CD/DVD-ROM drive
ide1 at 0x170-0x177, 0x376 on irq 15
hda: host protected area => 1
hda : 40011300 sectors (20486 MB) w/512KiB Cache, CHS=39693/16/63, UDMA(66)
	hda: hda1 hda2 hda3
hdb: host protected area => 1
hdb : 60058656 sectors (30750 MB) w/2048KiB Cache, CHS=59582/16/63, UDMA(133)
	hdb: hdb1
(hangs)

At this point in 2.4 the USB subsystem starts up, so it could be a problem there
of course.

00:00.0 Host bridge: VIA Technologies, Inc. VT8366/A/7 [Apollo KT266/A/333]
00:01.0 PCI bridge: VIA Technologies, Inc. VT8366/A/7 [Apollo KT266/A/333 AGP]
00:06.0 Multimedia video controller: Brooktree Corporation Bt878 Video Capture (rev 11)
00:06.1 Multimedia controller: Brooktree Corporation Bt878 Audio Capture (rev 11)
00:07.0 Multimedia audio controller: Cirrus Logic CS 4614/22/24 [CrystalClear SoundFusion Audio Accelerator] (rev 01)
00:0a.0 USB Controller: VIA Technologies, Inc. USB (rev 04)
00:10.0 USB Controller: VIA Technologies, Inc. USB (rev 80)
00:10.1 USB Controller: VIA Technologies, Inc. USB (rev 80)
00:10.2 USB Controller: VIA Technologies, Inc. USB (rev 80)
00:10.3 USB Controller: VIA Technologies, Inc. USB 2.0 (rev 82)
00:11.0 ISA bridge: VIA Technologies, Inc. VT8235 ISA Bridge
00:11.1 IDE interface: VIA Technologies, Inc. VT82C586/B/686A/B PIPC Bus Master IDE (rev 06)
00:11.5 Multimedia audio controller: VIA Technologies, Inc. VT8233 AC97 Audio Controller (rev 50)
01:00.0 VGA compatible controller: ATI Technologies Inc Radeon RV200 QW [Radeon 7500]

All the best,

Duncan.

Re: 2.5 BK boot hang after ide

[Felipe Alfaro Solana]

----- Original Message ----- 
From: Duncan Sands <baldrick@wanadoo.fr> 
Date: 	Sun, 23 Mar 2003 14:44:21 +0100 
To: alan@redhat.com 
Subject: 2.5 BK boot hang after ide 
 
> Copied down by hand: 
>  
> ... 
> ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx 
> VP_IDE: IDE controller at PCI slot 00:11.1 
> ACPI: No IRQ known for interrupt pin A of device 00:11.1 - using IRQ 255 
> VP_IDE: Chipset revision 6 
> VP_IDE: not 100% native mode: will probe irqs later 
> ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx 
> VP_IDE: VIA vt 8235 (rev 00) IDE UDMA 133 controller on pci00:11.1 
> 	ide0: BM_DMA at 0xfc00-0xfc07, BIOS settings: hda: DMA, hdb: DMA 
> 	ide1: BM_DMA at 0xfc08-0xfc0f, BIOS settings: hdc: DMA, hdd: DMA 
> hda: ST320423A, ATA DISK drive 
> hdb: Maxtor 6E030L0, ATA DISK drive 
> id0 at 0x1f0-0x1f7, 0x3f6 on irq 14 
> hdc: TOSHIBA DVD-ROM SD-MI402, ATAPI CD/DVD-ROM drive 
> hdd: LG CD-RW CED-8080B, ATAPI CD/DVD-ROM drive 
> ide1 at 0x170-0x177, 0x376 on irq 15 
> hda: host protected area => 1 
> hda : 40011300 sectors (20486 MB) w/512KiB Cache, CHS=39693/16/63, UDMA(66) 
> 	hda: hda1 hda2 hda3 
> hdb: host protected area => 1 
> hdb : 60058656 sectors (30750 MB) w/2048KiB Cache, CHS=59582/16/63, UDMA(133) 
> 	hdb: hdb1 
> (hangs) 
 
I'm experiencing exactly the same as you: 2.5 won't 
continue past IDE. I've tried 2.5.65-ac3, 2.5.65-bk3 
and 2.5.65-mm4. All of them fail at the same point. 
I've tried using ACPI, APM, disabling preempt, TCQ, 
enabling SysRq support, but had no luck. 
 
The machine is a Pentium 4 2.0Gz, with a QDI 
PlatiniX 2D/533-A (i845E), 2 UDMA100 disks 
(Seagate ST380021A 80GB and IBM-DTLA-307030 
20GB), a Pioneer DVD-ROM and Sony CRX185E3). 
 
-- 
______________________________________________
http://www.linuxmail.org/
Now with e-mail forwarding for only US$5.95/yr

Powered by Outblaze

Re: 2.5 BK boot hang after ide

[Duncan Sands]

> I'm experiencing exactly the same as you: 2.5 won't
> continue past IDE. I've tried 2.5.65-ac3, 2.5.65-bk3
> and 2.5.65-mm4. All of them fail at the same point.
> I've tried using ACPI, APM, disabling preempt, TCQ,
> enabling SysRq support, but had no luck.
>
> The machine is a Pentium 4 2.0Gz, with a QDI
> PlatiniX 2D/533-A (i845E), 2 UDMA100 disks
> (Seagate ST380021A 80GB and IBM-DTLA-307030
> 20GB), a Pioneer DVD-ROM and Sony CRX185E3).

2.5 BK worked for me two days ago, i.e. before Alan's
latest IDE changes went in.  Did any previous version
work for you?

Duncan.

Re: 2.5 BK boot hang after ide

[Felipe Alfaro Solana]

----- Original Message ----- 
From: Duncan Sands <baldrick@wanadoo.fr> 
Date: Sun, 23 Mar 2003 15:34:50 +0100 
To: "Felipe Alfaro Solana" <felipe_alfaro@linuxmail.org>, alan@redhat.com 
Subject: Re: 2.5 BK boot hang after ide 
 
> > I'm experiencing exactly the same as you: 2.5 won't 
> > continue past IDE. I've tried 2.5.65-ac3, 2.5.65-bk3 
> > and 2.5.65-mm4. All of them fail at the same point. 
> > I've tried using ACPI, APM, disabling preempt, TCQ, 
> > enabling SysRq support, but had no luck. 
> > 
> > The machine is a Pentium 4 2.0Gz, with a QDI 
> > PlatiniX 2D/533-A (i845E), 2 UDMA100 disks 
> > (Seagate ST380021A 80GB and IBM-DTLA-307030 
> > 20GB), a Pioneer DVD-ROM and Sony CRX185E3). 
>  
> 2.5 BK worked for me two days ago, i.e. before Alan's 
> latest IDE changes went in.  Did any previous version 
> work for you? 
>  
Yes, the last one I tried, before trying 2.5.65, was vanilla 
2.5.64, if my memory serves me well :-) 
 
-- 
______________________________________________
http://www.linuxmail.org/
Now with e-mail forwarding for only US$5.95/yr

Powered by Outblaze

Re: 2.5 BK boot hang after ide

[Nicholas Wourms]

Duncan Sands wrote:
>>I'm experiencing exactly the same as you: 2.5 won't
>>continue past IDE. I've tried 2.5.65-ac3, 2.5.65-bk3
>>and 2.5.65-mm4. All of them fail at the same point.
>>I've tried using ACPI, APM, disabling preempt, TCQ,
>>enabling SysRq support, but had no luck.
>>
>>The machine is a Pentium 4 2.0Gz, with a QDI
>>PlatiniX 2D/533-A (i845E), 2 UDMA100 disks
>>(Seagate ST380021A 80GB and IBM-DTLA-307030
>>20GB), a Pioneer DVD-ROM and Sony CRX185E3).
> 
> 
> 2.5 BK worked for me two days ago, i.e. before Alan's
> latest IDE changes went in.  Did any previous version
> work for you?
> 

I'm seeing the exact same behavior for AMD Opus.  It just 
hangs after the hdd, no messages.  I've been dropping 
printk's in random places, but still haven't figured it out. 
  Please see the "IDE Todo" thread for more info.  Also, it 
was working for me 2 days ago as well.

Cheers,
Nicholas

Re: 2.5 BK boot hang after ide

[Duncan Sands]

> > Copied down by hand:
> >
> > ...
> > ide: Assuming 33MHz system bus speed for PIO modes; override with
> > idebus=xx VP_IDE: IDE controller at PCI slot 00:11.1
> > ACPI: No IRQ known for interrupt pin A of device 00:11.1 - using IRQ 255
> > VP_IDE: Chipset revision 6
> > VP_IDE: not 100% native mode: will probe irqs later
> > ide: Assuming 33MHz system bus speed for PIO modes; override with
> > idebus=xx VP_IDE: VIA vt 8235 (rev 00) IDE UDMA 133 controller on
> > pci00:11.1 ide0: BM_DMA at 0xfc00-0xfc07, BIOS settings: hda: DMA, hdb:
> > DMA ide1: BM_DMA at 0xfc08-0xfc0f, BIOS settings: hdc: DMA, hdd: DMA hda:
> > ST320423A, ATA DISK drive
> > hdb: Maxtor 6E030L0, ATA DISK drive
> > id0 at 0x1f0-0x1f7, 0x3f6 on irq 14
> > hdc: TOSHIBA DVD-ROM SD-MI402, ATAPI CD/DVD-ROM drive
> > hdd: LG CD-RW CED-8080B, ATAPI CD/DVD-ROM drive
> > ide1 at 0x170-0x177, 0x376 on irq 15
> > hda: host protected area => 1
> > hda : 40011300 sectors (20486 MB) w/512KiB Cache, CHS=39693/16/63,
> > UDMA(66) hda: hda1 hda2 hda3
> > hdb: host protected area => 1
> > hdb : 60058656 sectors (30750 MB) w/2048KiB Cache, CHS=59582/16/63,
> > UDMA(133) hdb: hdb1
> > (hangs)
>
> I'm experiencing exactly the same as you: 2.5 won't
> continue past IDE. I've tried 2.5.65-ac3, 2.5.65-bk3
> and 2.5.65-mm4. All of them fail at the same point.
> I've tried using ACPI, APM, disabling preempt, TCQ,
> enabling SysRq support, but had no luck.
>
> The machine is a Pentium 4 2.0Gz, with a QDI
> PlatiniX 2D/533-A (i845E), 2 UDMA100 disks
> (Seagate ST380021A 80GB and IBM-DTLA-307030
> 20GB), a Pioneer DVD-ROM and Sony CRX185E3).

Seems to be OK with current BK.

Thanks,

Duncan.

Re: 2.5 BK boot hang after ide

[Felipe Alfaro Solana]

On Mon, 2003-03-24 at 10:38, Duncan Sands wrote:
> > I'm experiencing exactly the same as you: 2.5 won't
> > continue past IDE. I've tried 2.5.65-ac3, 2.5.65-bk3
> > and 2.5.65-mm4. All of them fail at the same point.
> > I've tried using ACPI, APM, disabling preempt, TCQ,
> > enabling SysRq support, but had no luck.
> >
> > The machine is a Pentium 4 2.0Gz, with a QDI
> > PlatiniX 2D/533-A (i845E), 2 UDMA100 disks
> > (Seagate ST380021A 80GB and IBM-DTLA-307030
> > 20GB), a Pioneer DVD-ROM and Sony CRX185E3).
> 
> Seems to be OK with current BK.

Yes, fortunately it's solved :-)

________________________________________________________________________
        Felipe Alfaro Solana
   Linux Registered User #287198
http://counter.li.org