From: Petro <petro@corp.vendio.com>
To: linux-kernel@vger.kernel.org
Subject: Oops report.
Date: Mon, 26 May 2003 11:35:25 -0700 [thread overview]
Message-ID: <20030526183525.GC21507@corp.vendio.com> (raw)
I'm probably going to complete screw this up:
Last night one of our test machines wedged while under a rather
moderate load. We were able to recover the oops from the serial
console (screen is your buddy):
At the time of the crash the machine was running Mysql 3.23.43 with
a rather large dataset--probably filling the available memory space.
The machine has been run hard for a couple days (loads of around 50,
CPU at 85% user, 15% system), lots of disk and network IO, basically
doing a lot of jpg->proprietary image conversions, then storing them
in the DB.) It had "come down" off this load, and was doing the same
thing + a lot of reading other images from the db when it hung.
I hope I've provided enough information.
Here is the output from kysmoops:
ksymoops 2.4.1 on i686 2.4.18. Options used
-V (default)
-k /var/log/ksymoops/20030525062539.ksyms (specified)
-l /var/log/ksymoops/20030525062539.modules (specified)
-o /lib/modules/2.4.18/ (default)
-m /boot/System.map-2.4.18 (default)
Warning (compare_maps): mismatch on symbol partition_name , ksyms_base says c0208860, System.map says c0158050. Ignoring ksyms_base entry
Warning (compare_maps): mismatch on symbol nlmsvc_ops , lockd says f89defb0, /lib/modules/2.4.18/kernel/fs/lockd/lockd.o says f89de408. Ignoring /lib/modules/2.4.18/kernel/fs/lockd/lockd.o entry
Warning (compare_maps): mismatch on symbol nfs_debug , sunrpc says f89d1524, /lib/modules/2.4.18/kernel/net/sunrpc/sunrpc.o says f89d1204. Ignoring /lib/modules/2.4.18/kernel/net/sunrpc/sunrpc.o entry
Warning (compare_maps): mismatch on symbol nfsd_debug , sunrpc says f89d1528, /lib/modules/2.4.18/kernel/net/sunrpc/sunrpc.o says f89d1208. Ignoring /lib/modules/2.4.18/kernel/net/sunrpc/sunrpc.o entry
Warning (compare_maps): mismatch on symbol nlm_debug , sunrpc says f89d152c, /lib/modules/2.4.18/kernel/net/sunrpc/sunrpc.o says f89d120c. Ignoring /lib/modules/2.4.18/kernel/net/sunrpc/sunrpc.o entry
Warning (compare_maps): mismatch on symbol rpc_debug , sunrpc says f89d1520, /lib/modules/2.4.18/kernel/net/sunrpc/sunrpc.o says f89d1200. Ignoring /lib/modules/2.4.18/kernel/net/sunrpc/sunrpc.o entry
Unable to handle kernel NULL pointer dereference at virtual address 00000028
c0164b12
*pde = 00000000
Oops: 0000
CPU: 0
EIP: 0010:[<c0164b12>] Not tainted
Using defaults from ksymoops -t elf32-i386 -a i386
EFLAGS: 00010213
eax: 0000084d ebx: 00000000 ecx: 000001d0 edx: 00000000
esi: e5ec0efc edi: 00000001 ebp: 00000050 esp: c4e55f10
ds: 0018 es: 0018 ss: 0018
Process kswapd (pid: 7, stackpage=c4e55000)
Stack: c4caec00 000001d0 00000000 00000017 00000000 c015cb86 f7589c00 c4caec00
000001d0 c013991c c4caec00 000001d0 c4caec1c c4caec00 c012f712 c4caec00
000001d0 00000020 000001d0 00000020 00000006 c4e54000 00000200 00024a85
Call Trace: [<c015cb86>] [<c013991c>] [<c012f712>] [<c012f9e6>] [<c012fa43>]
[<c012fad3>] [<c012fb2e>] [<c012fc3d>] [<c01055c4>]
Warning (Oops_read): Code line not seen, dumping what data is available
>>EIP; c0164b12 <journal_try_to_free_buffers+7a/c0> <=====
Trace; c015cb86 <ext3_releasepage+22/28>
Trace; c013991c <try_to_release_page+3c/54>
Trace; c012f712 <shrink_cache+23e/3bc>
Trace; c012f9e6 <shrink_caches+56/7c>
Trace; c012fa43 <try_to_free_pages+37/58>
Trace; c012fad3 <kswapd_balance_pgdat+43/8c>
Trace; c012fb2e <kswapd_balance+12/28>
Trace; c012fc3d <kswapd+99/b4>
Trace; c01055c4 <kernel_thread+28/38>
7 warnings issued. Results may not be reliable.
Now this ksymoops was run well after the reboot--the -k and -l options I
passed were the closest in time prior to the crash.
Here is the output of ver_linux:
If some fields are empty or look unusual you may have an old version.
Compare to the current minimal requirements in Documentation/Changes.
Linux dbspare00-red.auctionwatch.com 2.4.18 #1 SMP Wed Nov 20 18:57:08 PST 2002 i686 unknown
Gnu C command
Gnu make 3.79.1
binutils 2.11.90.0.24
util-linux 2.11h
mount 2.11h
modutils 2.4.6
e2fsprogs 1.22
reiserfsprogs 3.x.0j
Linux C Library 2.2.3
Dynamic linker (ldd) 2.2.3
Procps 2.0.7
Net-tools 1.60
Console-tools 0.2.3
Sh-utils 2.0.11
Modules Loaded nfs lockd sunrpc e1000
Note that the kernel was not compiled on this machine, on the machine it
was compiled on the Gnu C line is reads "2.95.4"--everything else is the
same. Well, except for the modules line.
This machine is a SuperServer 6022P-i (SYS-6022-Pi), with a SUPER P4DPI-G2
motherboard, 2 2.40Ghz CPUs:
(cat /proc/cpuinfo, all 4 entries are identical, here's the last:
Processor : 3
vendor_id : GenuineIntel
cpu family : 15
model : 2
model name : Intel(R) Xeon(TM) CPU 2.40GHz
stepping : 7
cpu MHz : 1799.813
cache size : 512 KB
fdiv_bug : no
hlt_bug : no
f00f_bug : no
coma_bug : no
fpu : yes
fpu_exception : yes
cpuid level : 2
wp : yes
flags : fpu vme de pse tsc msr pae mce cx8 apic sep mtrr pge
mca cmov pat pse36 clflush dts acpi mmx fxsr sse sse2 ss ht tm
bogomips : 3591.37
Hyperthreading is enabled.
cat /proc/meminfo
total: used: free: shared: buffers: cached:
Mem: 4092157952 4079968256 12189696 0 123207680 3683569664
Swap: 1077501952 5050368 1072451584
MemTotal: 3996248 kB
MemFree: 11904 kB
MemShared: 0 kB
Buffers: 120320 kB
Cached: 3594424 kB
SwapCached: 2812 kB
Active: 226780 kB
Inactive: 3622324 kB
HighTotal: 3145152 kB
HighFree: 2044 kB
LowTotal: 851096 kB
LowFree: 9860 kB
SwapTotal: 1052248 kB
SwapFree: 1047316 kB
here is the output of lspci:
00:00.0 Host bridge: Intel Corporation: Unknown device 2540 (rev 03)
Subsystem: Super Micro Computer Inc: Unknown device 3880
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
00:00.1 Class ff00: Intel Corporation: Unknown device 2541 (rev 03)
Subsystem: Super Micro Computer Inc: Unknown device 3880
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
00:02.0 PCI bridge: Intel Corporation: Unknown device 2543 (rev 03) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap- 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64
Bus: primary=00, secondary=01, subordinate=03, sec-latency=0
I/O behind bridge: 00003000-00003fff
Memory behind bridge: fc100000-fc3fffff
Prefetchable memory behind bridge: fff00000-000fffff
BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
00:04.0 PCI bridge: Intel Corporation: Unknown device 2547 (rev 03) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap- 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64
Bus: primary=00, secondary=04, subordinate=06, sec-latency=0
I/O behind bridge: 00004000-00004fff
Memory behind bridge: fc400000-fcffffff
Prefetchable memory behind bridge: fff00000-000fffff
BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
00:1d.0 USB Controller: Intel Corporation: Unknown device 2482 (rev 02) (prog-if 00 [UHCI])
Subsystem: Super Micro Computer Inc: Unknown device 3880
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin A routed to IRQ 16
Region 4: I/O ports at 2000 [size=32]
00:1d.1 USB Controller: Intel Corporation: Unknown device 2484 (rev 02) (prog-if 00 [UHCI])
Subsystem: Super Micro Computer Inc: Unknown device 3880
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin B routed to IRQ 19
Region 4: I/O ports at 2020 [size=32]
00:1d.2 USB Controller: Intel Corporation: Unknown device 2487 (rev 02) (prog-if 00 [UHCI])
Subsystem: Super Micro Computer Inc: Unknown device 3880
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin C routed to IRQ 18
Region 4: I/O ports at 2040 [size=32]
00:1e.0 PCI bridge: Intel Corporation 82820 820 (Camino 2) Chipset PCI (rev 42) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Bus: primary=00, secondary=07, subordinate=07, sec-latency=64
I/O behind bridge: 00005000-00005fff
Memory behind bridge: fd000000-fe0fffff
Prefetchable memory behind bridge: fff00000-000fffff
BridgeCtl: Parity- SERR- NoISA+ VGA+ MAbort- >Reset- FastB2B-
00:1f.0 ISA bridge: Intel Corporation: Unknown device 2480 (rev 02)
Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
00:1f.1 IDE interface: Intel Corporation: Unknown device 248b (rev 02) (prog-if 8a [Master SecP PriP])
Subsystem: Super Micro Computer Inc: Unknown device 3880
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin A routed to IRQ 0
Region 0: I/O ports at 01f0 [size=8]
Region 1: I/O ports at 03f4
Region 2: I/O ports at 0170 [size=8]
Region 3: I/O ports at 0374
Region 4: I/O ports at 2060 [size=16]
Region 5: Memory at fc000000 (32-bit, non-prefetchable) [size=1K]
00:1f.3 SMBus: Intel Corporation: Unknown device 2483 (rev 02)
Subsystem: Super Micro Computer Inc: Unknown device 3880
Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin B routed to IRQ 0
Region 4: I/O ports at 1100 [size=32]
01:1c.0 PIC: Intel Corporation: Unknown device 1461 (rev 03) (prog-if 20 [IO(X)-APIC])
Subsystem: Super Micro Computer Inc: Unknown device 3880
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Region 0: Memory at fc100000 (32-bit, non-prefetchable) [size=4K]
Capabilities: [50] #07 [0000]
01:1d.0 PCI bridge: Intel Corporation: Unknown device 1460 (rev 03) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64, cache line size 10
Bus: primary=01, secondary=02, subordinate=02, sec-latency=48
I/O behind bridge: 0000f000-00000fff
Memory behind bridge: fc200000-fc2fffff
Prefetchable memory behind bridge: 00000000fff00000-0000000000000000
BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort+ >Reset- FastB2B-
Capabilities: [50] #07 [0003]
01:1e.0 PIC: Intel Corporation: Unknown device 1461 (rev 03) (prog-if 20 [IO(X)-APIC])
Subsystem: Super Micro Computer Inc: Unknown device 3880
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Region 0: Memory at fc101000 (32-bit, non-prefetchable) [size=4K]
Capabilities: [50] #07 [0000]
01:1f.0 PCI bridge: Intel Corporation: Unknown device 1460 (rev 03) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64, cache line size 10
Bus: primary=01, secondary=03, subordinate=03, sec-latency=64
I/O behind bridge: 00003000-00003fff
Memory behind bridge: fc300000-fc3fffff
Prefetchable memory behind bridge: 00000000fff00000-0000000000000000
BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort+ >Reset- FastB2B-
Capabilities: [50] #07 [0083]
02:01.0 Ethernet controller: Netgear GA620 (rev 01)
Subsystem: Netgear: Unknown device 0001
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR+ FastB2B+
Status: Cap- 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (16000ns min), cache line size 08
Interrupt: pin A routed to IRQ 48
Region 0: Memory at fc200000 (32-bit, non-prefetchable) [size=16K]
03:02.0 Ethernet controller: Intel Corporation: Unknown device 1010 (rev 01)
Subsystem: Intel Corporation: Unknown device 1011
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (63750ns min), cache line size 08
Interrupt: pin A routed to IRQ 28
Region 0: Memory at fc300000 (64-bit, non-prefetchable) [size=128K]
Region 4: I/O ports at 3000 [size=64]
Capabilities: [dc] Power Management version 2
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=1 PME-
Capabilities: [e4] #07 [0002]
Capabilities: [f0] Message Signalled Interrupts: 64bit+ Queue=0/0 Enable-
Address: 0000000000000000 Data: 0000
03:02.1 Ethernet controller: Intel Corporation: Unknown device 1010 (rev 01)
Subsystem: Intel Corporation: Unknown device 1011
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (63750ns min), cache line size 08
Interrupt: pin B routed to IRQ 29
Region 0: Memory at fc320000 (64-bit, non-prefetchable) [size=128K]
Region 4: I/O ports at 3040 [size=64]
Capabilities: [dc] Power Management version 2
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=1 PME-
Capabilities: [e4] #07 [0002]
Capabilities: [f0] Message Signalled Interrupts: 64bit+ Queue=0/0 Enable-
Address: 0000000000000000 Data: 0000
04:1c.0 PIC: Intel Corporation: Unknown device 1461 (rev 03) (prog-if 20 [IO(X)-APIC])
Subsystem: Super Micro Computer Inc: Unknown device 3880
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Region 0: Memory at fc400000 (32-bit, non-prefetchable) [size=4K]
Capabilities: [50] #07 [0000]
04:1d.0 PCI bridge: Intel Corporation: Unknown device 1460 (rev 03) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64, cache line size 10
Bus: primary=04, secondary=05, subordinate=05, sec-latency=48
I/O behind bridge: 00004000-00004fff
Memory behind bridge: fc500000-fcffffff
Prefetchable memory behind bridge: 00000000fff00000-0000000000000000
BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort+ >Reset- FastB2B-
Capabilities: [50] #07 [0003]
04:1e.0 PIC: Intel Corporation: Unknown device 1461 (rev 03) (prog-if 20 [IO(X)-APIC])
Subsystem: Super Micro Computer Inc: Unknown device 3880
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Region 0: Memory at fc401000 (32-bit, non-prefetchable) [size=4K]
Capabilities: [50] #07 [0000]
04:1f.0 PCI bridge: Intel Corporation: Unknown device 1460 (rev 03) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64, cache line size 10
Bus: primary=04, secondary=06, subordinate=06, sec-latency=64
I/O behind bridge: 0000f000-00000fff
Memory behind bridge: fff00000-000fffff
Prefetchable memory behind bridge: 00000000fff00000-0000000000000000
BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort+ >Reset- FastB2B-
Capabilities: [50] #07 [0083]
05:01.0 RAID bus controller: 3ware Inc: Unknown device 1001 (rev 01)
Subsystem: 3ware Inc: Unknown device 1001
Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV+ VGASnoop- ParErr- Stepping- SERR+ FastB2B+
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 72 (2250ns min), cache line size 08
Interrupt: pin A routed to IRQ 96
Region 0: I/O ports at 4000 [size=16]
Region 1: Memory at fc500000 (32-bit, non-prefetchable) [size=16]
Region 2: Memory at fc800000 (32-bit, non-prefetchable) [size=8M]
Expansion ROM at <unassigned> [disabled] [size=64K]
Capabilities: [40] Power Management version 1
Flags: PMEClk- DSI- D1+ D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
07:01.0 VGA compatible controller: ATI Technologies Inc Rage XL (rev 27) (prog-if 00 [VGA])
Subsystem: ATI Technologies Inc: Unknown device 0008
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping+ SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (2000ns min), cache line size 08
Interrupt: pin A routed to IRQ 16
Region 0: Memory at fd000000 (32-bit, non-prefetchable) [size=16M]
Region 1: I/O ports at 5000 [size=256]
Region 2: Memory at fe000000 (32-bit, non-prefetchable) [size=4K]
Expansion ROM at <unassigned> [disabled] [size=128K]
Capabilities: [5c] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
--
"On two occasions, I have been asked [by members of Parliament], 'Pray,
Mr. Babbage, if you put into the machine wrong figures, will the right
answers come out?' I am not able to rightly apprehend the kind of confusion
of ideas that could provoke such a question." -- Charles Babbage
next reply other threads:[~2003-05-26 18:22 UTC|newest]
Thread overview: 11+ messages / expand[flat|nested] mbox.gz Atom feed top
2003-05-26 18:35 Petro [this message]
-- strict thread matches above, loose matches on Subject: below --
2009-01-02 8:42 OOPS report Daryl Radivojevic
2009-01-05 10:04 ` Oliver Neukum
2005-09-27 19:09 David J. M. Karlsen
2003-05-28 15:16 OOPs report Lawrence Walton
2003-05-28 22:53 ` Andrew Morton
2003-05-28 23:05 ` Dave Jones
2003-05-28 23:55 ` Andrew Morton
2003-01-25 17:05 Oops report Asher Yanich
2001-12-27 20:51 Mark Hindley
2000-12-22 10:48 Bill K.
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20030526183525.GC21507@corp.vendio.com \
--to=petro@corp.vendio.com \
--cc=linux-kernel@vger.kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox